Search Documents

By N. R. Sainath

This paper discusses a laboratory investigation that studied the microscale flow characteristics of copper ores and the variation in flow behavior resulting from flow of leach solution. Fractures in 40- and 100-mm-diam (1.5- and 4-in.-diam) cores were first mapped by visual inspection. The permeability of cores to water-stressed in a triaxial stress field representative of in situ conditions - was estimated. The samples were then exposed to 20g/L (2.7 oz/gal) sulfuric acid and the experiment was repeated. The porosity and the rate of recovery of copper from the specimen during leaching were also studied. The measured permeability of unleached samples with no visible fractures ranged from 10-16 to 10-19 m2 and it increased as leaching progressed. The porosity increased significantly with leaching, while the rate of copper recovery decreased.

Jan 1, 1994

By R. A. Wharton, Z. Yang, R. W. Smith

The electrokinetic and flotation behavior of the green alga Chlorella vulgaris was studied in the absence and presence of Pb(II), Al(III) and flotation collectors. It was found that the presence of Al(III) is necessary for good flotation of the organism, whether or not Pb(II) is present, when dodecylammonium chloride or sodium dodecylsulfate is used as collector. Best flotation using dodecylamine is at about pH 8, and best flotation when using sodium dodecylsulfate is at about pH 4. It appears because of the small size of the organisms that the Al(III) is necessary for flocculation to enhance bubble-cell contact and C. vulgaris removal from water. When N-dodecyl-2-aminopropionic acid is used as collector, good flotation occurs at about pH 4 without the addition of Al(III).

Jan 1, 1992

By M. Li, J. D. Miller

It has been discovered that water insoluble alcoholic solutions of alkyl hydroxamic acids serve as selective collectors for the flotation of phosphate mineral resources (Miller et al., 2000). The effectiveness of the new collector chemistry has been demonstrated by the results from single stage bench scale flotation experiments for feed material from plants in Florida, North Carolina, and Utah. In the best case, from experiments with low grade (5% P20,) coarse feed (16 x 35 mesh), a single stage phosphate recovery of 95% was achieved with a concentrate grade of 31% P20,. Such a separation efficiency could not be achieved using the traditional fatty acid/fuel oil collectors as is evident from a comparison of the respective grade/recovery curves.

Jan 1, 2002

By H. Sevim

The logic and capabilities of a long-term production planning method for open pit mining are presented. This is a new method that can be used to obtain simultaneous solutions to the four interrelated parameters of open pit mining: mine life, specific blocks to be mined each year, the amount of ore and waste to be mined each year, and the ultimate pit limits. An efficient milling cutoff grade can also be obtained through a systematic analysis. A production plan for a real-life gold deposit is given to illustrate the logic and the capabilities of the method.

Jan 1, 1994

By D. R. Zhu, H. S. Chiang, Y. M. Jiang, S. S. Peng

Two types of underground tests on three types of shield supports, 2-leg, 4-leg, and chock shield, were con- ducted to measure the horizontal movement of the canopy against the immediate roof. In no friction tests, steel rollers were placed between roof and canopy top, while in friction tests normal direct contact was used. Results indicate that the canopy for 2-leg shields always moves forward during setting, whereas there was no forward movement for 4-leg or chock shields. Based on the test results, a model for active horizontal force was proposed.

Jan 1, 1990

By D. O. Shah, K. C. Adiga

Flotation of coal after multistage addition of frother was found to yield coal fractions with significantly lower ash content as compared to the feed. Ignition and combustion characteristics of different coal fractions were evaluated using a differential thermal analyzer (DTA). A correlation between low ash content, low specific gravity, and high reactivity of coal was observed. It is suggested that in the ignition stage, removal of mineral matter enhances reactivity through the physical changes brought about by ash removal. A detailed analysis of pre-ignition kinetics indicated the possible effect of bulk density of coal in terms of resistance to volatile release and effective (available) surface area of coal. In the char combustion stage, mineral matter seems to influence reactivity through catalytic activity of surface concentrations of metal ions, ratio of combustible/non- combustible material, internal pore structure, and surface roughness.

Jan 1, 1988

By Yoshihiro Kawarabata

INTRODUCTION The shield-driven method in Japan has been adopted widely in soft ground tunneling, namely, subway, water supply, sewer and utility tunnels, and recently this is an indispensable method in urban area. Since this method was started to adopt on a full scale from the beginning of 1960, construction achievements in length were about 830 km for 15 years until 1974 (1). According to the recent informations of the Japan Tunneling Association, the achievement in length under construction as of December, 1977, was about 350 km (2) and the extention of increase in shield-driven method can be guessed (Tab. 1). Tab. 1 - Achievement in Length by Shield-driven Method (As of December, 1977, Unit: m) (---): Achievement by Okumura Corporation [ ]

Jan 1, 1979

By Y. M. Jiang

Longwall faces can move at high advancing rates, but many geological variations can cause unexpected instabilities and production losses. The rapid movement makes it necessary to evaluate different geologic conditions in the rock mass as fast as possible to assess their effects on the longwall face and shields. It is believed that prompt awareness of geologic conditions is the key to preventing instability at a longwall face. This paper introduces the application of fuzzy set theory for characterizing and evaluating roof conditions. Real-time monitored data coupled with fuzzy set analysis provides valuable information, such as shield leg pressure, developing load on shields, intervals of periodic weighting and the ratio of developing loads during periodic to normal times.

Jan 1, 1997

By Gülhan Özbayoglu, Yusuf Ziya Akgök

The effect of cooling rate on the flotation behaviour of copper slags of flash smelter plant in Samsun was investigated. Fresh molten slag was solidified in laboratory scale in three different ways. All the samples were characterized by chemical and mineralogical analyses. The chemical analyses showed that samples prepared from fresh slag had 0.9 to 1 % Cu with 40 % Fe and 30 to 32 % SO2. Old pit slag samples contained between 1 to 3% copper. Microphotographs showed that rapidly cooled slags showed fine size distributions, e.g. the copper grains in granulated slag had sizes in 1-2 microns. On the other hand, the size of copper grains in slowly cooled slags increased above 40 microns. Flotation tests carried out by using potassium amyl xanthate and Flotanol-C showed that slowly cooled slag reduced the copper losses in the tailing and improved the grade of concentrate. Under the light of laboratory investigation, the pit dimensions of Samsun Plant have been modified which resulted in a pronounced improvement of the grade and recovery of concentrate produced at Samsun slag flotation circuit.

Jan 1, 1995

By Chinmoy Sarkar

Mining organizations have been trying to employ best practices at exploration, exploitation and processing level to increase productivity in the supply chain. Traditional techniques of cost control can no longer meet the ambitious target of mine managers. An integrated perspective of Mining Value Chain with enterprise-wide application of information technology (IT) ensures the ability of every mining processes to improve energy, land, capital and labour resource performance while continuing to cut costs and achieve profitability. IT offers enormous potential in mining industry at shaping entirely new opportunities to create value. This paper characterizes important entities of Mining Value Chain and attempts to provide a vision on how IT can transform the mindsets of industry managers addressing the needs of the customers.

Jan 1, 2002

By Richard D. Grove

The on-stream analysis of phosphorus and silica has not been possible by XRF techniques and only recently has some success been indicated with quantitative XRD for P. Yet there has been a recognized need for an on-stream analysis of P and acid insoluble to permit the automatic control of phosphate rock flotation plants which produce some 30-40 million tons of concentrate each year in the southeastern U.S. IMC Fertilizer, Inc., the largest U.S. phosphate rock producer, embarked on a program to develop such an on-stream analysis capability several years ago. Following many months of lab and prototype development, the first commercial installations started in December 1986 and now have completed some 400,000 analyses with surprising accuracy, precision and reliability. The use of these devices in the improved control of the phosphate flotation plant is currently receiving some very serious attention at IMC.

Jan 1, 1989

By L. B. Rothfeld, R. L. Dolzani

This paper presents preliminary results of a US Bureau of Mines (USBM) study of potential costs of compliance with possible federal regulations for copper heap and dump leaching. The regulations could arise under amendments to the Resource Conservation and Recovery Act (RCRA) and/or the General Mining Law. Estimates are given for the cost of compliance with possible technology standards that would require the use of liners and closure caps regardless of terrain and underlying geology and hydrology. This cost is compared to the cost of compliance with 1992 state requirements for terrains typical of those found at existing copper leach sites in the southwestern United States. Incremental compliance costs are found to widely exceed screening criteria used by the US Environmental Protection Agency (EPA) to denote significant economic impact.

Jan 1, 1995

By Roger E. Melley

Since startup of the Syncrude Canada Ltd. (SCL) oil sands facility in northern Alberta 15 years ago, numerous improvements have been made in the ore conveying system and equipment. The unique nature of the material conveyed coupled with the wide range of environmental conditions encountered results in a number of unparalleled challenges. Most of the improvements have been brought about through the use of detailed field evaluation. Numerous publications are available that detail the various aspects of conveyor technology, and a significant list of papers are presented each year adding to the knowledge in this field. In the area of power formulae in the mid- 1970s, there were two major sources for use in the design of the SCL conveyors: the Conveyor Equipment Manufactures Association Handbook, 1988, and DIN Specifications 22101: Belt Conveyors for Bulk Materials, 1982. These sources were supplemented by the knowledge of the belt and conveyor equipment vendors and from the general literature. The SCL design was based on the CEMA formula. However, it was accepted that this empirical approach had been developed for use with more conventional materials in more reasonable climates. To accommodate

Jan 1, 1993

Acid mine drainage is still a common problem in the northern Appalachian high sulfur coal region despite mining and reclamation practices applied to control it. Mining companies must treat water with alkali to raise pH and precipitate metals in order to discharge the water into receiving streams. Common chemicals used to treat drainage are limestone, hydrated lime, soda ash briquettes, caustic soda, and ammonia. Each chemical has advantages or disadvantages under specific conditions. A simple spreadsheet program was developed to evaluate costs of treating acid mine drainage across several specified water quality parameters and time horizons. Caustic soda and soda ash were shown to be cost effective for treating low flows and low acidity over short time periods. However, as quantity of water increased, quality decreased, and time horizon increased, the ammonia and hydrated lime systems were found to be much cheaper than caustic soda.

Jan 1, 1991

By Staff

GENERAL DESCRIPTION The Lucky Friday mine is located in Mullan, Sho-¬shone County, Idaho. The mining method is horizontal slice cut-and-fill (with timbering for support or un¬timbered) using hydraulic sand. Cemented sand fill at a 1:17 ratio is used in sill pours and at a 1:7 ratio for the final 152 mm (6 in.) capping in successive stope floor pours. Annual production with 100% cut-and-fill mining is 167 829 t (185,000 st). The average depth of mining is 1296 m (4250 ft) and the average travel time to the stope is 45 min. GENERAL ORE BODY REQUIREMENTS AND LIMITATIONS Size The ore body is 396 to 488 m (1300 to 1600 ft) long on strike, 1421 m (4660 ft) on dip, with an average width of 2.3 m (7.5 ft). Dip varies from vertical to1.2 rad (70°) Ground Conditions, Ore Value, and Production Requirements The ore body contains quite strong argentiferous galena and quartz. The hanging wall and footwall are strongly sheared and fractured. Ore value is $211/t ($192/st).

Jan 1, 1982

By P. M. Solozhenkin

The proposed technology of antimony calcine processing includes ferrochloride leaching of calcine, reducing solutions, hydrolysis of hydrochloride solutions with antimony oxochloride isolation, synthesis of antimony trioxide by SbOCl neutralization and its drying, regeneration of hydrolysis solutions. The optimum parameters of separate stage of process has been determined and the chemical character of process has been given. During the leaching of calcine we succeeded to transfer 92.16- 95.66% antimony to solution. On the worked out sheme we attained recovery of antimony to antimony trioxide near 90 .5% Antimony triozide contains 99.5% Sb2O3. The composition of sinter burdens for pigments preparation "Naples Yellow" different colours from brightly-yellow, yellow and lightly yellow has been proposed. Three-sulfuretted antimony-antimonic cinnabar have been prepared by precipitation of antimony solutions by potassium sulfur-bearing solution. The prepared compounds correspond to inorganic pigments for artistic paint. The amorphous antimony-ferrous black we prepared by aluminium cementation of hydrochloric antimony solutions. The ferrous black were used as artistic paints and for coating of metals by antimony.

Jan 1, 1995

By Antti J. Niemi

Radioisotope tracers have so far been used for extraction of residence time distributions of flotation devices. They have also been proven applicable to evaluation of rate coefficients k of industrial flotation. It is now shown how values of k are scaled up on the basis of laboratory data on flotation and chemical conditioning, and of laboratory testing of samples from output of industrial conditioning vessel. Subsequently a model of conditioning and flotation is obtained which may be used for simulation and control of the steady state of the combined process. Discussion extends to modelling, simulation, CAD and opti- mization of flotation plants with re- circulation, and of ore dressing systems which consist of grinding and flotation plants.

Jan 1, 1990

By Thomas H. Koenning, James R. Boulton

The coal mined by Cyprus at the Shoshone mine near Hanna, WY is highly susceptible to spontaneous combustion. Spontaneous heatings have occurred in the gob of several of the longwall panels and, in some cases, following roof falls. Prevention and detection methods have evolved over the years as more has been learned about the occurrences. Seal design and construction have progressed to reduce air leakage into the gob. Pressure balancing has been successful as a supplement to good workmanship in reducing leakage. Early heating detection has improved as knowledge has been gained. Prior methods of detection relied upon thermocouples detecting a temperature change. Later a gas chromatograph was used to analyze gob gas samples. Initially the products of combustion (POC) were relied upon for detection. Most recently, lack of oxygen depletion in the gob has been used as an early warning of problems. Examples are presented to illustrate the evolution of spontaneous combustion control at the Cyprus Shoshone coal mine. Methods have been developed which minimize the oxygen concentration in the gob and reduce the potential for spontaneous combustion.

Jan 1, 1997

By V. K. Karra

Research by various workers has shown compressive comminution to be significantly more efficient than impact comminution. Based on the work being done at Nordberg, wet compressive crushing in cone crushers producing finer and finer products, shows the feasibility for partial substitution of conventional tumbling mills. For further substitution, major challenges are processing of fine feed slurries in cone crushers to realize a significant size reduction of the particles, and understanding the limitation of the gyratory type units in terms of finest product achievable. The paper addresses the challenges involved, efforts at Nordberg, and the implications to conventional comminution flowsheets.

Jan 1, 1989

By D. Krzyszton, P. Czaja

Mining explosions in rocks originate stress waves of great intensity, which crush the surrounding rocks and are then propagated as a seismic wave. Seismic waves are the cause of dynamic loading of pillars and their subsequent destruction. In calculating safe dimensions for inter-room pillars, not only the stresses conditioned by overburden pressures should be taken into consideration, but also the dynamic stresses caused by explosion. This is of particular importance for pillars with great specific acoustic impedance which have been destroyed mainly by the reflected seismic wave. It is possible to take dynamic loading into consideration in the calculation of pillars when the parameters of the propagation wave, the dynamic elastic constants of rocks, the strength properties of rocks, the strength properties of rocks subjected to dynamic loads and the parameters of the blasting charge are known. An example of the calculation for the safe width of an inter-room pillar subjected to the seismic effect of an explosion is given and the possibilities of reducing the dynamic loading of pillars are discussed.

Jan 1, 1982