Search Documents

By Dafydd Chandler, Milissa Hirst, Charles Hurst, Gary Snyder, Leszek Glodkowski

The Delaware County Regional Water Quality Control Authority (DELCORA) will be adding tunnel infrastructure to its wastewater conveyance system. This program involves the construction of a conveyance/storage tunnel and related facilities. The proposed 12- foot to 14-foot (±) finished diameter, TBM mined deep rock tunnel spans over 8.5 miles and lies approximately 80 ft-120 ft below the surface. The system is connected to the surface by at least five vertical online shafts and one offline shaft with associated 800ft long adit. This paper provides project details including data on the geologic conditions in which the tunnel will be constructed.

Dec 1, 2022

By Surendra Kumar Biswal, Sachida Nanda Sahu, B. C. Meikap

The unutilized iron ore fines (IOF, − 10 mm, 45% to < 60% Fe(T)) left at various mine sites during blasting and processing are rich in goethetic-hematite associated with high clay and considered a potential iron ore resource. The variation of loss on ignition (LOI) from mines to mines is based on the goethite and clay mineral content. The clay containing below 45 μm is mostly brittle, causing beneficiation problems. The IOF has an LOI of 7.83%, with high silica (5.52%) and alumina (4.57%), and 57.17% of Fe(T) subjected to both conventional deep beneficiation (CDB) and magnetization roasting using high-ash non-coking coal to adopt the suitable upgradation process. The CDB and magnetization roasting concentrate has 62.61% and 67.58% Fe(T) with 64.69% and 85.19% yield, respectively. However, the presence of 6.40% LOI in CDB makes the ore challenging for pelletization. Characterization like X-ray diffraction(XRD), scanning electron microscope(SEM), and chemical analysis was used to assess the concentrate quality and potential industrial application.

Jun 4, 2022

By B. Samanta, S. Bandopadhyay

Ore grade modeling of a placer gold deposit is considered a challenging problem even today. Typically, gold-bearing deposits show extremely erratic and unpredictable grade variation. This is principally because of isolated occurrences of gold metal within a few high-grade pockets. Because of sporadic fluctuation of high-gold-grade distribution, the overall spatial continuity of the deposit becomes poor. This type of variation is often described by a lognormal or highly skewed frequency distribution, and the spatial continuity of the deposit is characteristically represented by a variogram model that exhibits a high nugget component. Further complicating the matter is the sparse availability of drillholes to capture such erratic variation. Due to the prohibitive cost of drilling, gold grade and reserve estimations are typically carried out using insufficient exploratory data. Use of a traditional estimation technique on limited data often produces an unreliable ore grade model. Kriging and its nonlinear variation, lognormal kriging, are frequently used in gold deposit modeling (Rendu, 1979; Journel, 1980); however, kriging is flawed by the smoothing effect. Moreover, though kriging is known to be globally unbiased, it is not free from conditional bias. As a result, if a deposit is modeled using the traditional kriging technique, a high-grade zone can be predicted to be a low-grade zone and vice versa. Predicting high grade as low grade results in a missed opportunity to exploit profitable ore. On the other hand, prediction of low-grade ore as high-grade ore might result in financial loss for a mining operation. Thus, the use of kriging for ore grade mapping of a gold deposit may not be recommended. Estimation techniques (including kriging) can produce an estimate with minimum error in a minimum-error variance sense. However, no matter which estimation technique is used for grade modeling of a highly erratic deposit like gold, the error margin is bound to be high. Therefore, any grade prediction made for an unknown location is associated with high uncertainty. Since various mine-planning operations, including derivation of grade tonnage curve, pit design and economic analysis of the deposit, are based on estimated grade rather than true grade, a mining project evaluation that depends upon estimation will be subject to considerable risk. Thus, the successful design of a mining project not only depends upon accurate grade estimates, but also upon accurate assessment of uncertainty, for predictive grade is equally important. Although the kriging standard deviation is used as an indicator of uncertainty for prediction, it is flawed by characteristics related to a data-independence property. This study, therefore, investigates the stochastic simulation technique of conditional simulation for ore grade modeling of a placer gold deposit at Nome, Alaska. It is expected that the research will provide a better solution to ore-grade deposit modeling than the kriging technique because (1) conditional simulation preserves spatial continuity as well as reproduces the data histogram, thus avoiding the smoothing problem; and (2) generation of multiple realizations helps to accurately quantify the uncertainty about grade values in the deposit.

Jan 1, 2009

By P. Koh

A novel approach incorporating computational fluid dynamics (CFD) and flotation modelling has been used for investigating flotation cell designs. CFD modelling has increasingly been employed to enhance understanding of the cell hydrodynamics in mineral and coal flotation. Opportunities for improving the flotation cell performance can be identify by modelling. The CFD-flotation model from CSIRO incorporates cell hydrodynamics that affect particle-bubble interactions. Information from the model includes velocities, turbulent dissipation rates, gas hold-up, particle-bubble attachment and detachment rates. The attachment and detachment rates have been found to be effective measures of cell performance for cell design.

Jan 1, 2011

By K. Darcovich

The wettabilities of agglomerates made from coals of several different ranks were measured by the adhesion technique. Oil levels from 0 to 10% by weight were used. As was expected, it was found that higher-rank coals are more easily oil-wetted and that the surface properties of the agglomerates correlate with agglomeration recovery and ash removal data.

Jan 1, 1992

By D. L. Ogonowski, J. O. Marsden

The Candelaria copper-gold mine is located approximately 25 km south and east of Copiapo in Region III, Chile. The original concentrator was designed to treat 28,000 t/d (30,800 stpd) of chalcopyrite-bearing ore through a circuit consisting of a single 11.0 m(36 ft) diameter SAG mill, two ball mills, conventional rougher and scavenger flotation, column cell cleaner flotation, and ceramic disc filtration. The plant was commissioned in August 1994 and quickly reached design capacity and expected levels of metallurgical performance. In May 1996, a decision was made to double the capacity of the concentrator by the addition of a second line of equipment. The expanded facilities were commissioned in October 1997, less than 18 months after the decision to proceed, and well within the budget. The original concentrator facilities were replicated or duplicated as much as possible, however, a number of important equipment changes were made to take advantage of industry developments since the original concentrator was designed. These included the use of Eimco 120 m3 (4,200 ft3) cells for rougher and scavenger flotation and the installation of a Svedala VTM-800Vertimill for regrinding. This paper describes the rationale behind these changes and explores the reasons for the success of the project.

Jan 1, 1999

By Ali Keneti, Xavier Ryan, Gerardo Sanchez, Shannon Goff

In this study, FLAC3D modeling was conducted for ground-structure stability assessment for a pilot tunnel passing under a large shaft excavated in the vicinity of existing structures at Karangahape Station for the City Rail Link Project in Auckland, New Zealand. The analysis involved generation of the geometries and construction sequences in Rhinoceros®, modeling the existing ground condition, calibration of the simulated in situ conditions with the observed behavior of the ground, and excavation of the shaft and the pilot tunnel. A comprehensive interpretation of the results was then performed accompanied by comparison of the predicted behavior with the observed response of the ground during construction.

Dec 1, 2022

By A. L. Martikainen

Booster fans increase air pressure to overcome resistance, the objective being to force adequate amounts of air through distant workings. They are used in areas that are difficult or uneconomic to ventilate with main fans alone. Booster fans are currently permitted in underground coal mines in some countries; the United Kingdom, South Africa, Australia and Canada have been defined as major users. Booster fans are not allowed in the US bituminous and lignite coal mining operations at the present time due to safety concerns. This paper presents the history of booster fan use in coal mines of the United States during the last 90 years. Changes in regulations, as well as advantages and disadvantages of booster fan use, are discussed. Research and petitions for booster fan use are highlighted in order to bring the debate into focus.

Jan 1, 2010

"In the conceptual stages of engineering, benchmarking and empirical ratios are commonly the only references for estimating the production rate of greenfield projects. For underground mining projects, the lack of similar cases often makes the comparison difficult due to each project’s unique geology, rock quality or other singular characteristic. This paper discusses an analytical alternative for determining the maximum achievable production rate for underground stoping mining by modeling production as a continuous process. The results show that long-term maximum capacity depends exclusively on the achievable development rate and the development intensity of the design. In operations constrained by backfill, the development rate could be limited by the backfilling rate. Extraction rate and stope size only have impacts on capacity estimates during the ramp-up period.These findings allow shaping of the maximum capacity profile of a project. They can be used as a tool for quick assessment of conceptual capacities, and sensitivities of mining rates. Benchmarking tests compared favorably with projects, mines in operation and scheduling exercises. IntroductionA key consideration in the value proposition of a mining project is its capacity or production rate (Tatman, 2001). At a conceptual level, it is common practice to refer to empirical references (Taylor, 1986; Long, 2009), rules of thumb (de la Vergne, 2014), benchmark ing studies or consultant experience to estimate or validate a target value. There is, however, a lack of analytical methodology to guide an early estimate of the maximum capacity.Araneda and Gaete (2004) presented an interesting mathematical approach to estimate the capacity of panel caving mines. Using a continuous model, they confirmed that the mine capacity is essentially determined by the rate of area incorporation, in terms of area per period, and ore column height. This simple relationship has been confirmed by multiple detailed scheduling works"

May 1, 2016

By J. Hebert, J. Donnelli, J. Sedey

Installation of a Load Commutated Inverter (LCI) provides an economical method for conversion of a Fixed Speed Semi-Autogenous Grinding Mill into one with variable speed, qualities. Though capital intensive, the conversion appears to be one of the most cost-effective methods to gain the advantage of critical speed variations for variable ore characteristics. Expected advantages from the installation of LCI drives at the Goldstrike Mine were decreased liner wear, decreased media consumption and additional grind for increased production rates. These issues as well as construction, economics and performance will be discussed in the presentation. The utilization of the existing equipment came to play an integral part of the study and economic justification of the overall project.

Jan 1, 1999

PolyMet Mining is developing the NorthMet property near Duluth, Minnesota. Laboratory investigations had led to the development of the PLATSOL process to dissolve in one step the base metals (copper and nickel) as well as the gold and PGM’s. To complete the pre-feasibility study, a fully integrated ten-day pilot plant trial was undertaken, comprising of: high temperature (>220ºC) pressure oxidation in the presence of 5-10 g/L chloride (the PLATSOL process), followed by solid/liquid separation, gold plus PGM’s recovery from solution, conventional Cu SX/EW and recycling of the copper raffinate to the autoclave. The concentrate tested was a NorthMet bulk flotation concentrate assaying 14.7% Cu, 3.05% Ni, 0.14% Co, 26.7% S, 1.4 g/t Au, 2.2 g/t Pt and 9.9 g/t Pd. Laboratory results were fully confirmed and with minor adjustments of the laboratory PLATSOL® conditions, the following leach extractions were obtained during the pilot plant trial: Cu 99.6%, Ni 98.9%, Co 96%, Pd 94.6%, Pt 96% and Au 89.4%.

Jan 1, 2001

By Joseph Sopko, Xavier Lacourse-Dontigny

For the REM (Réseau Express Métropolitain) project, a 2500 m tunnel was built using a tunnel boring machine (TBM) under the Montreal Pierre Elliott Trudeau Airport (ADM). Although the geology under the Montreal Airport (ADM) would have been suitable for an excavation with a hard rock machine, the rst section reuired an earth pressure balance (EPB) TBM due to the soft soil located under wetlands. After excavating 280 m, the TBM was blocked in a transition zone of unconsolidated, water-bearing soils directly above the underlying bedrock. A free air intervention was not possible due to these geological conditions. After several failed attempts to create a slurry cake for hyperbaric interventions, a ground freezing system was designed and implemented, incorporating angled pipes drilled from outside the wetlands to directly in front of the cutterhead. This paper discusses the engineering reuired to form a frozen, water-tight zone in front of the cutterhead using liuid nitrogen. It also describes the complex method of replacing the disc cutters while holding the ground freezing system active in a manner protecting the health and safety of the workers.

Jun 23, 2024

By Raja V. Ramani

As the new millennium approaches, it is appropriate to assess the progress that has been made in mine health and safety, a matter of concern to management, labor and government. One can hardly look at the major events of the last century — from the birth of the US Bureau of Mines through the enactment of the modern health and safety laws — without realizing that the march has been relentless toward eradication of health and safety threats in mining. The progress is spectacular in mine safety and significant in mine health. In looking at the future, it is safe to assume that societal demands will increase for improved health and safety conditions in the workplace. So will the demands for greater technological leaps. The standards will for measuring success and the expectations of progress in creating a safer and healthier mine environment will grow. The possibilities are enormous of meeting these exacting requirements in the 21st century.

Jan 1, 1999

By G. E. Viens

The electric arc furnace has characteristics which make it attractive for a number of metallurgical applications. Some of these characteristics are: high thermal efficiency, the possibility of attaining very high temperatures, low off-gas volume compared to fuel-fired furnaces, no impurities are introduced by the heat source, and impurities in only minor amounts are introduced by the electrodes. It also has disadvantages, the chief ones being the relatively high cost of electrical energy compared to fossil-fuel energy and the fact that, when oxide ores are smelted using carbon as reductant, the off-gases emitted are rich in carbon monoxide. As in many other pyrometallurgical processes, fumes and dust are emitted from melting or smelting operations. In many installations, some or all of the off-gases are flared, thereby wasting their energy and contributing to atmospheric pollution. During the last eight years, a shaft-electric furnace has been under development at the Mines Branch, Department of Energy, Mines and Resources, Ottawa, Canada. This project was initiated to try to overcome, or at least minimize, the disadvantages of the electric furnace. Experience on other projects, prior to the beginning of this program, had indicated that preparation of the charge materials, for example by sizing raw ore, sintering concentrates and crushing and sizing the sinter, or agglomerating concentrates into uniform-sized pellets, could make a substantial contribution towards achieving success in arc-furnace smelting projects; This entire

Jan 1, 1971

By M. Hancer, J. D. Miller

It is known from soluble salt flotation practice that the K, Mg double salts of kainite (KClMgSO43H2O), and carnallite (KClMgCl26H2O) are difficult to float and must be converted to other salts such as schoenite (K2SO4MgSO46H2O) and sylvite (KCl) in order to recover potash values. The flotation characteristics of these double salts have now been confirmed in some detail by carefully controlled laboratory experiments with both cationic and anionic collectors. The experimental results are discussed in view of recent experimental findings regarding the flotation characteristics of simple salts, in which the flotation response was shown to be determined by the interfacial water structure and whether the salt could be considered to be a water structure maker or a water structure breaker. The same approach can be use to explain the flotation response of the potassium double salts ; schoenite, kainite, and carnallite. In addition, the sign of the surface charge of schoenite (K2SO4MgSO46H2O), was determined as a function of pH from nonequilibrium electrophoretic mobility measurements. Schoenite appears to exhibit three charge reversals (CR) which can be explained based on surface hydrolysis reactions. The flotation behavior of schoenite is further considered based on solution chemistry calculations, electrophoretic mobility measurements, and microflotation results.

Jan 1, 2001

By R. Elias

Botswana is a mining-dominated sub-Saharan country. Workforces are characterised by poorly educated operators and front line supervisors, with equipment and management to 1st World standards. Poor communication, ignorance of business objectives, inability to meet targets, and lack of problem-solving capacity are the norm. Training leads to high expectations and is of concern to management as a source of dissatisfaction, despite the long-term benefits higher skills have for mine viability. The aims of a technical training programme are presented with various models and approaches being implemented at operations in Botswana. These are used to construct a series of guidelines for technical training initiatives.

Jan 1, 2000

By Setareh Afrouz, Emily Sarver, Cigdem Keles

The resurgence of severe lung disease among US coal miners since the mid-1990s has led to efforts to better characterize and monitor respirable dust exposures, particularly focusing on mineral constituents from rock strata surrounding the coal. A rapid analysis method for silica (quartz) mass using direct-on-filter Fourier transform infrared (FTIR) spectroscopy has been developed, which can also estimate kaolinite, a primary silicate mineral in many coal mines.

Feb 24, 2022

By Gordon B. French, Donald E. Garrett

INTRODUCTION Crude oil reserves in the United States are still very large, even though for many years they have not been sufficient to supply our entire domestic requirements. They are continuously being depleted as oil is pumped from the ground, but new discoveries and improved secondary and tertiary recovery methods are helping to reduce the rate of depletion. It is thus a slowly diminishing resource, but even as it is being consumed, immense reserves of oil are left behind as the so called "un-recoverable" portion of petroleum formations. Most oil fields can only obtain a 15 to 40% recovery of the original reservoir, and it is widely quoted that there are still about 300 billion barrels of this un-recoverable oil still in place (Mauch, 1980, etc.). With the present comparatively high oil prices, and the possibility of even higher future prices and short supply, this oil becomes an interesting potential reserve. Mining the petroleum formation would be one means of recovering at least a portion of this oil. The concept of oil mining is neither new nor limited to conventional oil fields, since the procedure could be equally employed with the otherwise difficult to produce heavy oil deposits, and the solid or semi-solid tar sands and diatomaceous hydrocarbon formations. Estimates place the U.S. tar sand resource at about 30 billion barrels, and heavy oil at 5-10 billion barrels (Unitar, 1982). Figure 1 graphically summarizes the heavy oil reserves based upon formation depth and characteristics, while Figure 2 shows their location. It is apparent that the preponderance of reserves are in California and Texas, but that they also occur in many other states. The major companies engaged in oil recovery from the heavy

Jan 1, 1983

By Mohamed A. Younis, Paul J. Headland, Paul H. Madsen, Vojtech Gall

INTRODUCTION A 100 ft long, 20 ft high and 18 ft wide NATM tunnel was excavated through grouted clean sands beneath a busy city street, including a variety of existing utility lines. The new tunnel associated with a hospital expansion will serve as a pedestrian tunnel connecting a parking structure with a new hospital facility. Tunnel construction started on December 15, 2005 when drilling for the grouting program started and was completed on May 26, 2006 when the tunnel final lining was completed. The tunnel was constructed by Kiewit Construction Company as a tunnel subcontractor to The Christman Company who is constructing the hospital facility for Spectrum Health in Grand Rapids, Michigan. URS was the project designer. GallZeidler Consultants, LLC were the contractor’s NATM consultant. PROJECT DESCRIPTION The Michigan Street Pedestrian Tunnel is a component of the Michigan Street Development located along the north side of Michigan Street NE between Coit Avenue NE and North Division Avenue in the downtown area of the Grand Rapids, Michigan. The Michigan Street Development includes a parking deck and four new towers to be constructed over the proposed parking deck. The tower planned furthest east is being developed by Spectrum Health as the Lemmen-Holton Cancer Pavillion. The purpose of the pedestrian tunnel is to connect the proposed Lemmen-Holton Cancer Pavillion with the future Spectrum building to be located on the south side of Michigan Street NE. The southern end of the tunnel was constructed with a bulkhead until the future Spectrum building is constructed at which time interconnection will be required. The tunnel site plan and profile are shown in Figure 1, Site Plan, and Figure 2, Tunnel Profile. Several challenges were faced during the design and construction of the Michigan Street Pedestrian Tunnel. These challenges included compressed design and construction schedule, maintenance of traffic and protection of old underground utilities. The tunnel was being constructed as part of the Michigan Street Development and coordination with other concurrent construction activities was required. The tunnel was constructed within a specified window of time to allow other associated construction activities to take place without compromising the overall project schedule. The design started in June 2005 and construction was completed by June 2006.

Jan 1, 2007

By S. Al-Thyabat

In this work, the floatability of Jordanian phosphate slime (-38 µm) was evaluated in a batch column flotation cell, 100 cm high and 5 cm inner diameter. Flotation was conducted using sodium oleate as a collector and methyl isobutyl carbinol (MIBC) as frother. Rougher flotation yielded concentrate assaying 29.19% P2O5 with 90.29% recovery at the following flotation parameters: 2.6 cm/s superficial gas velocity, 20 ppm frother dosage, 0.205 mM collector concentration and 40% weight solids. It was also found that conditioning with the same collector dosage but with a different solids weight percent gave different flotation results. However, pulp collector concentration was the key operating parameter; increasing collector dosage at the same solids weight percent decreased flotation recovery by 3%, while increasing solids weight percent at the same collector dosage increased phosphate recovery by 18%.

Jan 1, 2011