Search Documents

By R. C. Gilmore, S. A. Lolon, G. E. Bogin, S. A. Saki, J. F. Brune, J. W. Grubb

"Gob ventilation boreholes (GVBs) are widely used in underground coal mines for longwall gob degasification purposes. GVBs are often drilled within 10 to 30 m above the top of the coal bed into the fractured zone, completed with 20 cm (8 in.) diameter casing and 60 m of slotted pipe at the bottom. The purpose of this completion strategy is to create a pressure sink to capture the emissions before they can enter into the underground workplace. For GVBs to work effectively, they must be drilled close enough to the working areas to capture methane from the fractured zone while the setting depth must be kept above the caved zone to minimize the amount of ventilation air that is drawn into the GVBs. Well completion parameters are important for creating safe working conditions. In this paper, computational fluid dynamics (CFD) studies will be presented to analyze the effect of different practices for GVBs completion parameters for methane extraction, formation of explosive gas zones in the gob and methane concentrations at the longwall face and tailgate. Authors have identified the optimum completion parameters for GVBs, which can maximize the benefit and minimize fire and explosion risk. INTRODUCTION Coal mines may be considered gassy based on the presence of CH4. Gas from the mined coalbed or from rider seams above or below the mined coalbed can migrate into the gob and then potentially move towards the working areas. In longwall coal mines with high methane emissions, sufficient ventilation and additional methane control measures are usually required to reduce the methane concentration in working areas to below statutory levels. Several techniques or combinations of techniques are available to control the methane hazard. These may include mine face ventilation to dilute methane, coal bed degasification, nitrogen injection into the gob to render a methane atmosphere inert and the use of gob ventilation boreholes (GVBs). Longwall face ventilation and dilution alone can only handle methane emissions up to a certain amount. When methane emissions exceed the face ventilation capacity, additional control measures are required. Drilling horizontal or vertical methane drainage holes into the coal seams as well as gob ventilation boreholes from the surface into the gob area to extract methane are common practices. GVBs are usually drilled from the surface above the longwall panel ahead of mining. When the face moves outby the GVBs and the gob begins to form, methane production starts from the boreholes. It is important to control the performance of GVBs to maintain a safe working environment in the mine. The performance of GVBs depends on multiple factors, including borehole location, length and diameter of slotted casing, setting depth of casing above the coal seam being mined, wellhead vacuum pressure, and permeability of caved-fractured zones."

Jan 1, 2016

By S. D. Bearden

The world's barite reserve base is adequate for at least 100 years at the current consumption rate. China, India and the United States are expected to remain the leading producing countries, and the United States will continue to be the largest consumer. None of the known substitutes for barium sulfate are expected to impact existing applications. World production in 1995 was 4.41 Mt (4.86 million st), which is about 50% of capacity. Consumption is directly proportional to hydrocarbon well installation activity. Imports are expected to continue to supply more than half of the US requirements.

Jan 1, 1998

By Neall. George M.

No method of roof control yet devised has proven to be universally acceptable for the wide range of strata conditions experienced in U.S. coal mines. However, a relatively new innovation, the roof truss, has proven itself capable of preventing roof failures which both conventional and resin bolting could not. Presently, the economics of roof trusses are not favorable when compared to bolting due primarily to drilling and installation procedures, but this is expected to change with improved truss and equipment designs. To realize the full potential of this new method of roof control, design criteria are needed which can optimize the effect of the truss for varying strata conditions. A review of the literature reveals that some work has been conducted on the roof truss. 1 Gambrell and Haynes (1970) showed that the roof truss is superior to angled roofbolts installed through a header. Sheorey, Verma, and singh2 (1973) used statics to prove that the optimum angle of inclination should be greater than 450? However, to date, no systematic attempt has been made to establish design criteria. In this report, the problem was approached in three ways. First, model studies were performed to determine general trends of truss support as a function of a number of variables. This provided a better understanding of the support mechanism involved. Secondly, beam theory was employed to calculate the actual support capacity of a truss, realizing the many simplifications, assumptions, and shortcomings of this approach to such a complicated problem. Last, field testing will be utilized to test the hypotheses previously developed and provide hard data to further synthesize roof truss design criteria. Field testing has recently commenced and should be complete before mid 1977.

Jan 1, 1977

By R. L. Virta

Common clay is a natural, fine-grained material composed of hydrous aluminum silicates. Shale is a laminated sedimentary rock formed by the consolidation of clay, mud and (or) silt. Government and legislative programs The U.S. Environmental Protection Agency (EPA) invited industry to nominate representatives to a review panel that will help the EPA develop rules to regulate air toxics from the production of brick and structural clay products. The EPA was required to establish a review panel because these regulations will significantly affect small businesses. The regulation of air toxics falls under the Clean Air Act.

Jan 1, 2010

By SME SME

List of 43rd ICGCM 2024 ORGANIZING COMMITTEE

Jun 25, 2024

By Otto E. Zwanzig

You may think long before this talk has been completed that the speaker is belaboring the obvious. Please let me put to rest here and now any doubt which you may have in this regard by assuring you that is precisely my intent, and for a very specific reason. We all profess to know and recognize the obvious, but I am impressed increasingly how often we forget or fail to act upon the obvious. Shortly after starting my first job upon graduation from college, I was asked by my boss to participate in a course on practical communications, particularly as applied to conveying proposals effectively to the client -- be he customer or company president. The concept or philosophy underlying this program was so simple and obvious that in my youthful brashness I saw only a gross waste by the company of e good, solid $1930 in compelling me to take the course. The sequel to this experience occurred about five yews ago when I was directing a 300-man marketing group. At that time I enrolled a dozen of my department heads, and subsequently about a hundred other personnel, in the contemporary version of that sane program. Why? -- because they all knew the obvious, but I could see how imperfectly they were implementing it. Truly, a wide chasm exists all too often in our beliefs on the one hand and our practices on the other.

Jan 1, 1962

By Edward H. Peplow

Mr. Chairman; honored guests; ladies and gentlemen: The subject assigned me today by your committee, according to the program, is "the mineral industry and the public land law I have preferred to title the talk, "you can't mine here", for that is the essence of the message we, as an industry, have been getting from so many agencies of the federal government for so long. And, unfortunately, we can expect to hear the same message even louder and clearer -- with increasing frequency in future, unless. Every segment of the industry devotes the necessary time, energy and creative thought to combat successfully the forces that are writing and broadcasting that message. I said that agencies of the federal government are sending the message --- and this, of course, is true, the forest service, for example, and some bureaus of the department of the interior as well as others have appeared in recent years to be abiding by a policy designed to block mineral entry to as much of the public lands as possible and to wipe out existing mining claims.

Jan 1, 1967

By D. S. Bubar

This presentation will represent a diversion from the central theme of Cordilleran geology, in both time and space, as we move 2,000 miles east of Spokane to eastern Canada, specifically the province of Quebec, to discuss a major new Archean-age volcanogenic massive sulphide deposit called Louvicourt. The deposit is located in the Val d'Or camp in the prolific Abitibi Greenstone Belt some 400 miles north of Montreal. It was discovered by Aur Resources in June, 1989 on a property operated under the terms of a joint venture with Louvem Mining, a Quebec company controlled by Ste. Genevieve Resources Inc. of Montreal. As a geologist, I am proud to be able to describe Louvicourt as a geological discovery, as it was found by doing systematic deep diamond drilling based on a geological concept. The deposit is essentially blind from surface and lay undiscovered for the 10 years that the Louvem mine was in production just 2,000 feet away from its easternmost workings.

Jan 1, 1991

By W. L. Dare

Land use planning is not a new concept in the United States but the emphasis has changed drastically since the early 1960's. Under the old interpretation we tried to expand our frontiers and develop our land, but as society has become more affluent and mobile the demand has grown to preserve those parts remaining undeveloped. There is something of a paradox inherent in this change of emphasis. While affluence has motivated our support to preserve the quality of the natural environment, industrial development is needed to support the affluence. Because we cannot accomplish all of each, sound planning and compromise will be necessary since it is unlikely that, the American people will want to surrender much of their life-style or their awakening environmental concern. Any industrial society, whether a goal reached or an aim yet ahead, is built largely on the use of mineral raw materials and energy, the physical base of nearly all activities and products. The standard of living which is important to us all is growing more dependent upon these minerals, metals, and energy fuels. Although reduction in consumption of raw materials may be acceptable to those at a certain economic level of a society, those who have not reached that level cannot be expected to accept a lowering of their present or anticipated standard of living.

Jan 1, 1974

By Judson C. Higgins

The paper addresses changes in surface transportation methods in the Industrial Minerals business starting with history, the changes to present time including such areas as energy costs, improved highways, changes in regulations and deregulation, and attempts to project future transportation trends. Transportation methods such as rail, piggyback, truck and barge are compared, and their impact on Industrial Minerals producer's costs and profits examined. The customer impact on our businesses due to deregulation is also discussed.

Jan 1, 1983

By T. L. Myron

To determine the effect of flux crystal size on the production rate and strength of sinter, batch sintering tests were conducted on samples of both dolomite and limestone of various crystal sizes. In addition, calcination tests .were performed on the dolomite and Limestone to determine the effect of crystal size on calcination rate at various temperatures normally attained in sinter beds. The results indicate that flux crystal size does not affect sinter production rate or sinter strength.

Jan 1, 1962

By Martin J. Hughes

The Eagle Mountain Mine of the Kaiser Steel Corporation is located in the California portion of the Colorado Desert at a distance of about 60 miles east of Indio, California. At the present time, this mine is producing at the rate of 5,000,000 tons of concentrate per year. A total of 1,000,000 tons of ore per year is presently being sold on the Japanese market while the remainder is consumed by the Kaiser Steel Company blast furnaces at Fontana, California. A new Pellet Plant and Concentrator is presently under, construction with completion scheduled for May or June 1965. This plant will have a rated capacity of 2,200,000 tons of pellets per year and essentially all of this production will be sold to Japanese steel companies.

Jan 1, 1965

By Syd S. Peng

According to accident statistics (l, 2), roof fall accidents occur quite frequently at the intersections of underground? openings and account for up to 30% of the roof fall fatalities. But this figure will certainly go up considerably if roof falls not associated with any fatal accident are included in the analysis. Unfortunately, nonfatal roof falls are seldom documented. In the underground coal mines, there are two types of entry intersections. One is the three-way (V type) and the other is the four-way (T type) intersections. A three-way intersection occurs whenever the mainline track haulageway turns at an angle into a section haulageway. The four-way intersections by far the most common type in the U.S. under-ground coal mines are formed by the intersections of two entries which are oriented perpendicular to each other or by the intersections of entries and crosscuts. However, crosscuts are frequently driven at an angle to the entry to facilitate machine movements. The four-way intersections formed by this method of crosscut development are angled. At the intersection of two underground openings, the diagonal roof span is wider than the width of each individual opening. This is one of the major reasons why roof falls occur more likely at the intersections than in the entry between pillars. Consequently, special intersection support plans are usually employed (Figs. 1 and 2) for intersections. The most popular practices are to decrease roof bolt spacing 1 ft. less than or to increase roof bolt length 1 to 2 ft. longer than those employed in the entry between pillars (3). The increase in bolt length or decrease in bolt spacing can be applied to all of the bolts in the intersection or employed only for the strategically located bolts depending on the individual mine practices. These rather generalized practices seems to be adequate for some areas but in many cases inadequate for others. Occasionally, the neighboring two lines of chain pillars are staggered such that the crosscuts in one row of chain pillars face the centers of the chain pillars in the neigh-boring rows. This layout forms T-type three-way intersections which are also inadequate for most weak roofs (3, 4). A study was therefore initiated to develop special techniques for intersection supports. The first phase of the study was the analysis of the stress fields for the underground entry intersections. A three-dimensional stress analysis was necessary for this purpose. Unfortunately, the three-dimensional problems of complicated boundary conditions are beyond the existing analytical methods. The three-dimensional finite element method (FEM) was therefore employed in this study. In the analysis, square pillars of 40 feet wide and an entry height of 8 feet were assumed while entry widths varied at 14, 20 and 26 feet. This model was selected to simulate the mine where roof falls data were collected. The second phase of the study was the collection of field data. The sizes of the roof falls including heights, lengths and widths were collected and analyzed. In the third phase study, the results of the first and second phases were compared and discussed. The analysis of field data revealed an arching zone within which roof falls occurred. The arching zone above an entry obtained empirically was compared with the calculated stress contours. Assuming that the bolts must be anchored in the rock strata outside the arching zone, the preferable systems of bolting were proposed. Also the amount of pretension required to inhibit sliding between layers was discussed.

Jan 1, 1978

By Robert H. Raring

Viewed abstractly, a mill may be defined as a mineral processing facility located somewhere between the mine and the tailings storage area, Just how mining operations and the demands of tailings storage affect mill design is, the subject of this paper. At the outset, it will be readily acknowledged that no two installations can, or ever will be the same. At one extreme is the bucket line dredge where the distance between the ?mine? and the tailings area is measured in terms of tens of feet. At the other extreme, the large open pit copper mines are frequently spread across twenty, miles or so of countryside with the ore moving to the mill, as exemplified by the operations at Bingham Canyon, Ray, or Ruth - the "upstream" counterparts of Garfield, Hayden and McGill. In each of these cases, mill location was largely determined by requirements for tailings storage and/or water supply.

Jan 1, 1961

By J. R. Tonry

In the grinding of dry non-metallic materials such as rocks, ores, gypsum, lime, and cement clinker, it is recognized that only a relatively small portion of the energy is utilized for actual size reduction, and the major portion of the energy used is converted into heat. As a result, heat is generated inside grinding mills imparting to the ground product a higher temperature than that of the mill feed. In some cases, as for instance in grinding cement clinker and gypsum into finished cement, it may be desirable to keep this temperature increase within certain limits, to avoid any change in the properties of the product and, because consumers may specify a maximum temperature of the finished product for reasons associated, with the tulimate use of the cement. The actual proportions of heat and useful work are somewhat indefinite. Some tests have indicated that nearly all the energy is converted into heat, and. other investigators have found that they could account for "everything except the noise." Investigations sponsored by the American Institute of Mining and Metallurgical Engineers, and carried out with an adiabatic calorimeter, indicated that a surprisingly high 19 percent of the energy might actually be used for size reduc¬tion. However, for the purpose of the following discussion it will be assumed that: (Fig. 1) 10% is lost in motor and gears 10% is lost by radiation and convection from the mill body 10% is used for size reduction, and. that 70% of the energy input leaves the mill as heat in the ground. product. A typical example (Fig. 2) would be a 7x22-ft tube mill operating in open circuit, driven by a 400 hp motor, charged with 77,000 lb of grinding media and producing 70 bbl or 26,300 lb of cement per hour. Reducing this cement from a clinker size of 96 percent passing a No. 16 mesh sieve to a specific surface of 3,230 sq cm per gm (Blaine) will increase the temperature of the cement approximately 143F above the temperature of the feed, as explained later. If the tempera¬ture of the clinker therefore is 125F, the finished cement will be 268F, which in some cases may be too hot. : When cement temperatures approach a range during grinding where dehydration of the gypsum becomes a problem, a logical consideration would be some means of reducing the temperature before it attains the range conducive to gypsum dehydration. Regardless of the varying degrees of heat generated within the mill or mills during grindingto various finenesses, consideration of the maximum safe limit for any type of cement being ground, which may vary fromplant to plant, govern in refining the mill circuit to obtain a safe temperature range. All plants are not necessarily required to do the same cooling job, and may or may not use cement coolers following the grinding circuit. (Not discussed in this paper). In the past, various means have been employed for controlling this temperature increase, Such means have included water cooling of the outside of the mill shell; equipping the shell with cooling fins; injection of moisture inside the mill; ventilation through the mill; and., in cases of closed-circuit grinding, drawing cooling air through the classifier; the purpose in all such cases being to remove heat from the grinding system.

Jan 1, 1958

By Lawrence Pelham

The demand or consumption of fluorspar has been somewhat taken for granted in recent years, except for the specific interest of those that produce, market, and/or consume the commodity. A tradition was established of thinking that as the steel and aluminum industry goes, so goes fluorspar. This is much less true today than in the past. The industry is becoming more dependent on chemical industries that feed primarily off hydrofluoric acid (HF) production. The Bureau of Mines recently published an assessment of world fluorspar reserves and resources that created a foundation of valuable data that can be used to monitor fluorspar availability. Celebrations were held this year commemorating the 100th anniversary of the isolation of fluorine. The United States and other countries continue to struggle with the controversy of ozone depletion and the effect of fluorocarbons on the atmosphere. The goals for the U.S. Government's strategic stockpile are being reevaluated. The market for fluorine chemicals is changing and diversifying, making it a challenge to assess and forecast fluorspar/fluorine demand. This paper reviews the recent past of fluorspar and helps set the stage for a more detailed assessment of this critical commodity.

Jan 1, 1986

By Giovanni Barla

This paper examines the application of gelatin mixture models to the study of factors such as gravity effects, tectonic and residual stresses, anisotropy, physical nonlinearity, time-dependent behavior of the rock mass and connectedness of the geologic space. The calibration technique of gelatin mixtures, proposed by Richards and Mark in 1966, is applied to the particular problem considered. Similitude relationships between model and prototype are discussed with reference to the constitutive equations describing the physical behavior of the rock mass. The interaction between two openings in a linearly elastic medium, under conditions of plane strain, is used as an illustrative example, with the view of describing the history of stress and deformation changes on the rock medium and lining around a slusher drift while undercuts are made in block caving.

Jan 1, 1968

This treatise presents the application of the vertical furnace in a carbon regeneration system. Comparison is made to a rotary kiln. The construction, operation and control of the vertical furnace and system components are discussed. Advantages include high efficiency, fuel economy, minimal mechanical apparatus and maintenance, atmospheric and temperature control, ease of operation and reliability.

Jan 1, 1985

By A. H. Summers

The La Choya mine is located 55 km south of Sonoyta in northwestern Sonora, Mexico. Mineralization is controlled by a 40 meter thick thrust fault zone which created a permeable host for the metal-bearing hydrothermal solutions. The ore body is mined by open pit using wheel loaders and truck haulage. Gold and silver are recovered from low grade ore by heap leaching followed by carbon adsorption.

Jan 1, 1997

By R. S. Olson

The operation of a series wash thickener-two stage filtration circuit determines the soluble loss in many hydrometallurgical operations A study of this circuit yielded expressions which permit calculation of soluble loss for almost any condition of operation. The soluble loss over a range of the circuit variables is presented to illustrate and evaluate circuit performance, The interrelation of factors affecting filter performance and some of the wash circuit, variables are quantatively described. Filter wash, which is governed by wash zone size, filter pulp level and filter feed pulp density, has the greatest affect on soluble loss. Excepting clothing blinding and flocculation the factors which decrease filter capacity also decrease soluble loss. Repulping with water, under some circumstances, can bean important means of soluble loss reduction. Water for primary filter wash, leach pulp density repulp density and wash thickener underflow density have little effect on soluble loss. The dilution of both o the filter pulps with wash solutions is suggested as a means of reducing soluble loss, and at the same, time, controlling the performance of the filters. Blowback and filter cloth blinding seriously increase soluble loss.

Jan 1, 1962