Search Documents

By Roger Holmberg

INTRODUCTION The driving of drifts is a very important aspect of underground mining. It is not unusual for the percent¬age of rock broken during development in a mine using sublevel caving, for example, to be as much as 25% of the total. If one also considers the amount broken for transport, ventilation, and exploration drifts, one can easily understand that the planning and excavation of drifts play a major part in the total economics of the mine (Fig. 1). Increasing mechanization in mining demands larger tunnel areas for transport and mining equipment. With modern machines the hard work involved in using hand¬held pushers is gone, and a better environment is achieved. More rational methods could be used, but much of the experience the working man acquired by working close to the rock face (such as utilizing the natural weak planes in the rock when he placed the drill¬ing holes) has unfortunately been lost. By having sepa¬rate shifts for drilling, loading, and hauling, more atten¬tion has to be placed upon a well-designed drilling pattern. Some reduction in the number of holes required can be achieved with mechanized drilling because of the larger holes that can be produced. On the other hand, it is probably not possible to achieve the same precision as with pneumatic pushers, and it is difficult to utilize the larger holes because these cause more damage to the re¬maining rock. Recently, however, the precision has be¬come very good with the parallel booms and automatic devices for setting the lookout angle (Fig. 2). A larger arch of the drift roof requires a more carefully executed blasting procedure than before in order to prevent rock fall and to insure a sufficiently long stand-up time. In this chapter, empirical relationships that can be used to design an economic and optimal drift blasting design will be presented. The principles of the calcula¬tion method are based upon the earlier work of Langefors and Kihlström (1963) and Gustafsson (1973). COMPARISON OF EXPLOSIVES To provide for the use of various explosives it is necessary to have a basis of comparison. Several meth¬ods have been developed to characterize the strength of an explosive. Some examples are comparison of values given by (1) calculated explosion energies; (2) the ballistic mortar test; (3) the Trauzl lead block test; (4) the brisance test; (5) the weight strength concept; and (6) the underwater test. However, most of these meth¬ods should be used carefully when stating the breaking

Jan 1, 1982

By R. W. Carn, D. Vincent

During the next 15 years, US coal production is expected to double, with the increased production evenly divided between the East and the West. Along with greater production, coal export markets should increase dramatically from East, West, and Gulf Coast ports. The annual overseas export capacity of US coal-loading terminals is expected to rise from 147.1 Mt (162.1 million st) in 1981 to a minimum of 278.1 Mt (306.6 million st) in 1985, according to the US Maritime Administration. Increased coal production and use will lead to more development of import and export terminals, a vital link in the coal transportation chain. With continually escalating capital costs and the competitive markets that the terminals will serve, a well designed and efficient terminal is necessary. This article begins a two-part series that presents concepts presently used in coal export terminal design. Part I looks at site selection factors and equipment needs, while Part II will examine environmental considerations in building a terminal as well as typical capital and operating costs. The world is nearing the end of the oil era. In a few years oil will not be available to sustain the growth rate and increasing standard of living we have known in our lifetime. The big question is what energy era are we moving into? With the decline of readily available oil reserves and rapidly increasing prices, many countries are trying to switch to alternate energy forms. While intensive efforts to find new oil reserves continue, alternate energy sources such as natural gas, coal, synthetic fuels, nuclear, hydroelectric, solar, and wind power are being developed. Recent indications are that coal is expected to bridge the energy gap over the next 25-30 years until the technology and economics of the alternate energy forms reach satisfactory levels. Use of coal for energy is receiving strong attention due to its long-term availability (200-300 years minimum), relative ease of development, and its low cost per unit of power produced. By the year 2000, it is expected that 25% of world energy supply will be met by direct coal combustion and possibly another 5-10% by synthetic fuel from coal. Coal's expanding share in the world energy market, along with an increase in coking coal requirements, will result in a large increase in the world's seaborne coal trade. Recent statistics and projections for the future are shown in Table 1. This phenomenal development rate includes increases in both coking and thermal coal requirements. Because of the rapid increase of seaborne coal trade during the last 10 years and the even greater projected increase of trade to 2000, various sectors of the coal industry are faced with enormous technical challenges and huge investments in equipment, land, transportation systems, and port facilities. Very large bulk terminals are under development throughout the world. Latest surveys indicate that there are about 30 new coal export and import terminals under consideration and at least 30 existing terminals have expansion programs planned or underway. With the high cost of borrowed capital and rapid inflation rates there is great emphasis on new planning and design techniques to minimize capital and operating costs of coal transportation systems. Terminals A total coal supply system can be considered to consist of one or more mines; a train, barge, truck, or other haulage system; an export terminal; a fleet of bulk carriers; a receiving terminal; and possibly, local inland distribution networks that include barges and railways. Terminals, though only a small link in the total transportation system, play a key role in overall system efficiency. At ports or inland distribution centers, terminals act as transportation links bringing trains, ships, barges, or trucks together for cargo transfer and temporary storage. A well-designed terminal can provide maximum independence between two modes of transportation and optimum freedom for intermodal interference. A terminal acts as a buffer between the two transportation modes by providing sufficient storage capacity so a ship need not wait for its cargo on, for example, a train-by-train basis, but can load immediately from the ready stock. Similarly, a train need not wait for a ship to unload its contents but can dump immediately into storage. A terminal also can be used to properly mix various types of coal to satisfy a buyer's requirements. Consider the relative value of various production and transport segments for a typical steam coal

Jan 6, 1983

By Paul J. A. Lever, Robert H. King

Human operators, geological conditions, equipment changes, mining sequences, and roof conditions are some of the continually changing operating conditions that drive a dynamic mining environment. These dynamic characteristics make it difficult to automatically analyze mining data because attributes change as the mining environment changes. Mine monitoring systems could provide mine managers with much more useful information than they do presently, if automatic analysis were possible. Automatic analysis of sensor data is also key to autonomous mining systems. This paper describes artificial intelligence (AI) and sensor fusion based sensor data analysis techniques developed over the past four years. These techniques were used to classify machine operating events by continuously monitoring machine power usage in a continuous miner section at an under- ground coal mine. The result is a report similar to an industrial engineering time study. First, numerical pattern classification techniques broadly identify operating events. However, domain knowledge about inter-machine and intra-machine interactions is necessary to identify and refine dynamic event boundaries. By implementing AI and sensor fusion based techniques we are able to classify machine events more accurately and recognize more specific events. These techniques could easily be applied to many different mining sensor data applications

Jan 1, 1993

By T. E. Wilson

The length of Alaska's coastline, combined with the presence of a significant number of fjords, encourages consideration of marine disposal of mine tailings. However, the decision-making process is complex because various factors govern the viability of the submarine tailings disposal (STD) option. An expert system, called the Submarine Tailings Disposal Expert System (STADES), was developed to help mining project planners explore the feasibility of STD. A review of the existing literature, supplemented by engineering recommendations, on the various aspects of the marine disposal of tailings formed the knowledge base for the expert system. The shell used to develop the expert system was LEVELS.

Jan 1, 2003

By S. A. Beeson, C. Poole

This paper describes the development of a novel selective flocculation technique for recovering phosphate values from ores containing silicate or carbonate gangue minerals. Data from initial flocculation response and reagent adsorption studies on component mineral suspensions and synthetic mixtures were used to assess the influence of various process parameters (e.g., reagent dosages, particle size, solids concentration, and conditioning regimes) on single-stage selective flocculation tests involving natural silicate and carbonate ores. In these tests a high degree of selectivity was achieved using low dosages of a low-molecular-weight cationic dispersant and a mid-range molecular weight cationic flocculant. Testwork was then extended to the evaluation of several floc recovery systems (sedimentation, hydrocyclones, and floc flotation) in a multi-stage process involving redispersion and reflocculation. Results from these tests clearly demonstrated the feasibility of producing marketable phosphate concentrates from both ore types.

Jan 1, 1999

By A. Probst, N. Moores, J. A. Finch

In 1994, McGill University and INCO Ltd. (Sudbury operation) initiated the transfer of technology originally developed to detect levels in equipment ranging from flotation columns to thickeners. A conductivity probe was installed in a concentrate thickener to monitor the mud line and the solids load. The probe consisted of a vertical tube with 32 equally spaced electrode rings connected in pairs to give 31 conductivity cells. Conductivity was measured as a function of depth to produce a conductivity profile. From the conductivity profile, the mud line and the percent solids can be inferred. The probe was installed in October 1994, and it has been successfully detecting profiles since then. This paper includes a description of the incidents that occurred and the experiences gained during this technology-transfer process. Discussed is probe installation and startup; software modifications to accommodate both operating conditions and the needs of the operators; and calibration procedures to adjust to changes in performance as a consequence of long-term use. Also included are preliminary observations of the still-in-progress last stage, i.e., signal interpretation and use to facilitate operation, particularly by providing early reaction to upstream disturbances.

Jan 1, 1999

By Hans Breuer

The new regulations for the bituminous coal mining industry, issued by the mining authorities of the Federal Republic of Germany, are aimed at reducing to a feasible minimum any development of the coal workers pneumoconiosis (CWP) by lowering the admissible dust exposure of mine workers. Additional and improved measures of dust suppression and job assignment control *) are required for the purpose In this connection two basically different demands are placed on dust measurements: As far as dust suppression is concerned, the causes of dust development and the effectiveness of methods applied to reduce dust concentrations have to be identified, whereas with regard to the control of job assignment, the dust exposure of mine workers has to be depermined. Demands placed on dust measurements -- specifically for determining dust exposure -- are liable to become more severe since the threshold limit values were considerably reduced in these last years and since any additional dust suppression measures as well as a purposeful job assignment to certain mine workers are dependent on relevant measuring data. Therefore, research work has been carried out with the objective of measuring and evaluating, in terms of their effect (i. e. their incidence on the development of a CWP), size distribution, concentration, and specific noxiousness of any prevailing dust conditions.

Jan 1, 1980

By P. L. Dunn

Automatic control of fine coal cleaning circuits has traditionally been limited by a lack of sensors. Although several nuclear-based analyzers are available, none have seen widespread acceptance. In this investigation, image analysis is used for on-line determination of ash content in fine coal slurries. The ash content of a flotation tailings stream is correlated to the mean gray level of the slurry. Based on a 90% prediction interval, an analysis of sensor performance indicates an accuracy of 73 ± 4% ash over a range from 65-90% ash. While this result is comparable to existing nuclear-based analyzers, the video-based system is only a fraction of the cost. The sensor is currently installed at the Middle Fork preparation plant owned by Pittston Coal Company.

Jan 1, 1997

By I. Longson

As a longwall coalface advances a caved goaf or waste region is left behind. Air flow takes place through this permeable goaf due to the pressure differentials existing across it and en route this leakage air picks up both heat and moisture. A marked deterioration in climatic conditions occurs in the face area at all points downstream of where this leakage air rejoins the main air-stream. This goaf heat source can make a very significant contribution, typically 30-40% to the rate of total heat pickup on an advancing UK longwall coalface with a VST of 40°C and hence on the climatic conditions that prevail at the return end and in the return gate of the face. The magnitude of the rate of heat collection from the goaf depends on a number of factors but it has been established that it is particularly influenced by the prevailing virgin rock temperature and the total flow rate of the leakage air. This paper proposes a model for the goaf based on a packed bed analogy and other assumptions required in order to evaluate the rate of heat pickup are identified. The outlet condition of the leakage air predicted by the model have been shown to correlate with underground measurements taken for a range of different production patterns with the face cutter at various locations on the face. The sensitivity of these predictions to variations in the input data has been tested and is commented on. At this stage of the development the capabilities and predictive limitations of the model are discussed. Further areas of investigation are suggested in order to improve the predictive ability and to extend the versatility of the model.

Jan 1, 1989

By K. H. McDaniel

This paper describes the development of a Windows-based interactive mine ventilation simulation software program at the Waste Isolation Pilot Plant (WIPP). To enhance the operation of the underground ventilation system, Westinghouse Electric Corp. developed a program called WIPPVENT. While WIPPVENT includes most of the functions of the commercially available simulation program VNETPC from Mine Ventilation Services Inc. and uses the same subroutine to calculate airflow distributions, the user interface was completely rewritten as a Windows application with screen graphics. WIPPVENT is designed to interact with WIPP ventilation-monitoring systems through the sitewide central monitoring system. Data (e.g., air quantity and differential pressure) can be continuously collected from the underground ventilation remote-monitoring and control system and from the mine's weather stations (psychrometric data). Furthermore, WIPPVENT incorporates regulator characteristic curves specific to the site. The program utilizes this data to create and continuously update a real-time ventilation model. This paper discusses the design, the key features and the interactive capabilities of WIPPVENT.

Jan 1, 1997

By S. P. Mehrotra

In this review article, various approaches and mathematical models that have been used to simulate, design, and synthesize flotation circuits are examined. First, a brief review of flotation kinetics is presented which is followed by a discussion on simulation of flotation circuits. The existing literature on optimal design of flotation circuits has been divided into two broad categories. In the first category, a generalized integral approach is used wherein the optimal circuit design involves determination of both optimal interconnection of various flotation cells/ banks of cells in terms of structural parameters and optimal values of various operating parameters. In the second category, a conventional circuit configuration is assumed to be the best configuration; the optimal design here only means the optimization of operating parameters. The merits and demerits of these two approaches are discussed.

Jan 1, 1987

By T. Dlokweni, A. Z. Toper, A. P. Squelch, R. G. Gürtunca

A collaborative research programme called 'DEEPMINE' was established in 1998 to investigate and research the problems of mining below three and five kilometres depths. Backfill is considered as an important support strategy to alleviate rockburst and rockfall problems in current depths and it will even become a more crucial mining strategy at ultra-deep level mining. In this paper, the evaluation and the application of the current backfill design criteria to the ultra-deep level mining environment are studied and a new backfill design criteria is proposed. The new criteria suggests that backfill should still be placed 60 - 70% of the area mined with a maximum fill to face distance of three metres. Furthermore, the vertical stress generated in backfill should be between 2 - 3 MPa at maximum 25 metres from the face at a corresponding strain value of maximum 10%.

Jan 1, 2001

By d&apos, L. R. Fletcher, Andrea. D. V., M. A. Peltier

The Bureau of Mines analyzed coal mine blasting accident data obtained from the Mine Safety and Health Administration (MSHA), U.S. Department of Labor. The data were examined to determine the causes, frequency, and severity of accidents in an effort to point out the most dangerous aspects of coal mine blasting. Accident data for the 14 years from 1971 through 1984 show that there has been a total of 43 fatal and 926 nonfatal blasting accident victims in surface and under- ground coal mining. This is an average of 3.1 fatal and 66.1 non- fatal injuries each year. Underground coal mining accounted for 60.5% of the fatal and 78.7% of the nonfatal accidents involving explosives and breaking agents in coal mining. In addition, since 1970 there have been 53 fatal and 20 nonfatal injuries that occurred when explosives were the ignition source for dust and/or methane explosions in underground mines. Abstracts from 297 accidents that occurred from 1978 through 1984 were also examined to determine accident causes. Most accidents occur during scheduled blasting, and failure of the blast area security system is the leading cause. Blast area security problems in surface mining are failure to clear the blast zone, failure of personnel to follow instructions, inadequate guarding, and failure to retreat to a safe location and/or take adequate cover. Other common causes in surface mining include premature blasts, excessive flyrock, and misfires. In addition to the above causes, accidents in underground coal mining can be due to rockfalls triggered by the blast, unexpected breakthroughs, fumes, and incidents associated with Airdox-type systems.

Jan 1, 1986

By Z. Rogovin

A Knowledge of the amount of time the material spends in a continuous mill in a closed-grinding-circuit is essential for circuit performance analysis and scale-up design. A convenient method for acquiring this information involves the use of tracers in residence-time-distribution (RTD) experiments. In a typical wet process the RTD measurements are usually done by injecting a pulse tracer into the mill inlet and detecting it in the circuit exit. In this article a simple to use mathematical method for the calculation of the closed circuit material residence time in the mill is developed. Using this method there are no restrictions on the location of the tracer injection or detection points. Any convenient location in the closed circuit can be chosen without affecting the simplicity of the method. This method also enables the calculation of the degree of mixing in the mill. The use of this method for the analysis of impulse response data obtained from several commercial grinding circuits is presented.

Jan 1, 1986

By D. J. Lachel, Douglas E. Hansen, Bruce Kennedy

The very high cost of exploration and development for new mines requires that a carefully planned, complete, and technically competent geotechnical evaluation be applied to the ore body and the surrounding rock. The ground conditions must be predetermined sufficiently so that, during the development and exploitation stages, unexpected conditions will be of minor consequence. Ground conditions are a major factor affecting the cost of excavated items such as shafts and inclines. For example, shafts cost less to sink in tight dry ground than in highly pervious ground below the water table, with all other factors being equal. The proper mining methods also is dependent upon the ground conditions. Bad ground for room-and-pillar mining may be ideal for caving methods; whereas, ideal ground for room-and-pillar mining would be extremely difficult for a caving operation. To do a proper engineering design, the parameters of strength, deformability, and permeability must be determined, in addition to the loads that will be applied as a result of the mining activity. The required degree of accuracy for each parameter depends upon the individual case. For example, the strength of massive rock in which openings of small cross-sectional area are to be driven at shallow depths needs to be resolved only within several thousand kilopascals (pounds per square inch). Under such conditions, the rock strength is not likely to be of great economic importance unless the rock is very weak. Large openings at great depths require a much more accurate appraisal of rock strength and deformation characteristics. Ground water conditions are important at any depth. Today, a number of techniques exist for evaluating conditions before opening up the ground for development. These techniques and their applications are described in more detail later in this text. The evaluation of ore body ground conditions should start at an early stage, as soon as the deposit has been proven viable for a mine. Economic geology investigations mainly serve to define the value and limits of the ore deposit. To do this properly, the geology of the site is determined in at least as much detail as is necessary to define the "controls" for the ore body. The ground-condition evaluation must determine the engineering properties of the ore body and the surrounding material. This includes the structural geology as it relates to rock strength; i.e., the frequency, extent, and orientation of discontinuities such as faults, joints, bedding, etc. Ground water conditions also must be determined. It is important that the detailed geology of the site be determined at an early date. Reasonable geotechnical parameters must be established during this time period, so they can be used in mining model studies that include both physical and mathematical models. The ultimate goal bf-the geotechnical evaluation is to predict the ground behavior as the excavations are made and how the ground behavior will affect the safety and economic well-being of the mine. The formulation of a ground-condition evaluation program should be planned carefully to determine the particular geotechnical parameters only in as great a detail as will have a bearing on the mine design. For instance, it is not necessary to make numerous triaxial tests in strong rock when the mining will be conducted within a few meters (feet) of the surface in a regime of gravity loading and an absence of tectonic stresses. Similarly, it is not necessary to invest large amounts of time and effort in the determination of joint strengths if the orientations of the joints are such that the failure could not occur along them. Generally, the determination of ore body ground conditions can be divided into four main steps: 1) The general and structural geology of the site must be determined; this is determined primarily during the economic evaluation. 2) The material behavior characteristics of the deposit and the vicinity must be determined. 3) The ground water hydrology of the deposit and the vicinity must be determined. 4) Miscellaneous ground support considerations must be established. Gross features are defined first, followed by a series of increasingly detailed investigations. Specifically, the geology study should start by utilizing techniques such as remote sensing, topographic map interpretation, geologic mapping, etc. After the gross features, such as major faults, have been delineated, the studies are directed toward defining the more detailed elements of jointing, rock strength, ground water hydrology, and other characteristics. This information is used to formulate an assessment of the strength of the ore body and the surrounding rock. Finally, all of the gathered information is integrated to make an assessment of the rock behavior in relation to the types of openings, the excavation methods, the support requirements, etc., that should be used for the rock conditions that are present. The mine design and the geotechnical assessment should be an iterative process. General conclusions about the rock conditions will dictate a type of mine plan. The specific mine plan then should be modified by specific geotechnical considerations. For example, an initial assessment may conclude that the ore body is strong and that a strong rock unit is present over the ore body. Thus, one definite possibility is to mine the deposit by room-and-pillar methods. However, subsequent investigations may reveal faults through the deposit, requiring relocation of the mine openings so that pillars and other structures are in sound rock. In other words, the final mine plan should be compatible with the geotechnical aspects of the ore body.

Jan 1, 1982

By B. T. Mirabile, D. Tang, Y. Luo, S. S. Peng, C. T. Holland

Knowledge of local coal mine roof geology is critical to the design of a safe and suitable mine structure. An automated drill control and data collection system has been designed for a J.H. Fletcher twin-head roof bolter. Drilling parameters collected during the drilling process can be used to interpret geologic features intercepted in the mine roof. The drill and data collection system have been tested in both laboratory and underground settings. Visualization of certain drilling data has shown good correlation with geology drilled. A quantitative prediction model was developed using drilling parameters examined with data visualization. The quantitative model was tested using laboratory drilling data.

Jan 1, 2004

By R. F. Harig

Designing an underground nuclear waste repository is a complex process. Although many decisions are involved before the design is complete, the first three--what the target horizon is, what the underground boundary is, and where the entry point will be located--are important because they establish the basis for the entire repository design. Even more important than these decisions, however, is the data on which the decisions are based. Because the current data are limited, an aggressive data gathering program is needed during the next design phase to augment information about the intricate interplay among all facets of the repository design and the geologic medium in which the proposed repository is to be developed. Although unique to modern engineering enterprises, the challenges involved in designing a repository in the unsaturated zone are within current technology and engineering practices.

Jan 1, 1991

The exploitation of mineral deposits for economical recovery of the contained minerals has many aspects differing from other industrial or manufacturing operations. However, generally accepted principles of good organization and management applicable to industrial plants are similarly effective for mineral processing plants. A more detailed coverage of organizational structures and management techniques than is possible in this section can be obtained from many good books devoted wholly to these subjects. A few of the more readily available examples are included in the general references at the beginning of this section. The field of mineral processing encompass a wide variety of minerals, processes, flowsheets, equipment, and end products. Mineral deposits, mines, and related beneficiation plants are found in all parts of the globe, often in remote locations with no nearby support for supplies and maintenance. Available labor is frequently unskilled, sometimes primitive, and often untrained without machine and hand tools or heavy equipment experience. Such situations call for well- planned and conducted training programs covering the full range of mining-type job skills. Climates can range from arctic to tropical and from arid to extremes of rain or snow, and the mine and plant sites can be almost anywhere. However, it is often possible and sometimes necessary for

Jan 1, 1985

By Steve Wirch, Robert Jankowski

The issue of dust control in underground coal mines has been extensively studied by both government and industry. This research work has resulted in many techniques which control the dust or help miners avoid it. Control techniques either prevent the dust from becoming airborne or cleanse the air before it can be inhaled. Avoidance measures minimize the exposure of miners to the airborne dust by blowing the dust away from work areas or making it unnecessary for a miner to occupy a dusty region. One of several successful dust control measures in continuous miner sections is the use of a machine mounted scrubber which cleanses the air and helps to prevent the contaminated air from reaching areas frequented by mine personnel. Research on the application of scrubbers on longwall shearers began in the 1970s and continued into the 1980s. The most successful projects showed only moderate improvement when a scrubber system was mounted on a longwall shearer, and the less successful projects actually increased worker dust levels. There are many reasons that scrubbers have not been successfully applied on longwalls. The most significant of these is that longwalls have across the face ventilation and generally have high face air flows. Scrubbers tend to work best when they are the primary cause of ventilation. Therefore, their capture efficiencies on longwalls tend to suffer because of the exposure of the drums to the primary airflow. Other reasons scrubbers have not been implemented on longwall s include the successful application of an excellent water spray system, effective cutting techniques, and dispersion of dust sources. These techniques can help control drum generated dust, increase production, and limit the relative effectiveness of a scrubber.

Jan 1, 1995

By S. P. Taite, A. R. Charest, P. D. Lewis

The El Sauzal deposit is a classic, high sulfidation, epithermal gold system located in southwestern Chihuahua State, Mexico. The prospect was discovered by a Francisco Gold Corp. geologist in1995. El Sauzal was encountered as a result of an extensive grass-root exploration program in the rugged, dissected volcanic terrains of the Sierra Madre Occidental, around the historical Batopilas Silver Camp. At El Sauzal, high grade gold is hosted within a series of more permeable, low-dipping, lithic and fine-grained dacitic rocks of early Tertiary age. The mineralization appears to be both structurally and lithologically controlled. The alteration characteristics are typical of a high sulfidation system including kaolinite, illite, alunite, dickite and pyrophyllite. The deposit’s gold distribution, as recorded from drill-hole data and surface samples, varies from 0.2 to 650.0 g/t. The estimated geological resource, as calculated from an independent study completed in 1998, was 3.0 million oz @ 2.03 g/t including a minable reserve of1.8 million oz @ 3.3 g/t.

Jan 1, 2004