Search Documents

By Paul H. Muller

The configuration of remote seal DP cells for specific gravity measurement is described and the calculations for calibration are presented. The error induced by ambient temperature change is investigated as it relates to capillary dynamics and electronic considerations. Instrument specifications are discussed in the light of accuracy requirements and the calculation of error vs. ambient temperature is described.

Jan 1, 1984

By W. W. Wen

Approximately 3 percent of the raw coal processed in U. S. Steel coal-preparation plants ultimately reports to slurry- tailing disposal. The usual disposal method is to pump the refuse slurry containing the minus-48 mesh (300 µm) refuse into dams or impoundments that are constructed of the coarse refuse. The failure of an impoundment at Buffalo Creek, Saunders, West Virginia and the sliding failure of a coarse refuse pile at Aberfan, Wales, England, resulted in an evaluation of refuse disposal methods by various regulatory agencies as well as coal producers. The result of this evaluation was the promulgation of Federal regulations dealing with the construction, operation, and final abandonment of coal refuse disposal areas. As a consequence of these regulations the use of the landfill/impoundment method of disposal became in some cases economically urlfeasible or technically impossible. U, S. Steel has studied a number of alternative methods of refuse disposal. During an investigation of mechanical dewatering with a pressure filter, Portland cement was added to the slurry to solidify the filter cake. Because of the success of the cement addition it was decided to study the stabilization of fine-coal-refuse slurry through use of cement-type additives.

Jan 1, 1979

By G. W. McCaa

Plans for a large industrial development in the Upper Ohio Valley between Moundsville and New Martinsville, West Virginia, were announced in the Fall of 1955. This development consisted of a large aluminum plant to be .built by Olin-Mathieson; a 675,000 KW power plant to be constructed by the American Electric Power Service; and a large coal mine adjacent to the power plant to be developed by the Hanna Coal Company Division of Consolidation Coal Company. The Ireland Mine was designed to efficiently supply fuel for the power plant, and this was the first consideration in the location of facilities, design, and development of plant and the selection of the equipment. The first problem was to find a suitable area for the surface facilities. A level bottom area south of the power plant was reserved for future industrial plants and this area was also blocked off from the coal reserves by an old abandoned and flooded mine. The coal storage facilities of the power plant were on the north side of the plant and it was decided to locate the coal mine preparation plant on-the shoulder of a hill above the power plant. This location required the excavation of 70,000 yards of rock but permitted the driving of a belt slope from the plant at an angle so that the haulage roads underground would miss the abandoned Cresap Mine. This location also permitted the plant to be located at an elevation so that the conveyors leaving the plant were horizontal and had sufficient clearance above the highway and railroad tracks. The other surface facilities consisting of air shafts, supply slope, supply yard, office, bathhouse, shop and warehouse were located in the valley some distance north of the preparation plant. This location placed these facilities one mile nearer to the working area. Plans for design and development of the mine were started in November 1955; grading and clearing of surface area was started in January 1956; the air shafts and slopes were started in the Spring and Summer of 1956; and the first coal was produced from the supply slope in October 1956. The preparation plant was put in operation in March 1958, and by July 1959 was producing 8,000 tons per day.

Jan 1, 1959

By D. P. Caplice

On behalf of the Ontario Water Resources Commission, I would like to express my sincere appreciation to your Institute for presenting us with this opportunity to outline the regulatory control programme as it relates to the mining industry in the Province of Ontario. In Canada, and particularly in Ontario, we are blessed with an abundance of natural resources. Fresh water in the form of lakes and rivers covers nearly 17 per cent of the area of the Province. (Total area of the Province of Ontario is 412,582 square miles.) The mining industry, which had its beginning in the early 1800's with a small iron ore plant, has progressed with the major discoveries of nickel and copper in 1883, silver in 1903, gold in 1908, iron in 1939 and uranium in 1953, to the point where, in 1966, almost one billion dollars in mineral wealth was mined in Ontario. Water, in spite of its great abundance and with due respects that it may become a natural resource worthy of export in the foreseeable future, has become increasingly precious in Ontario, particularly in the more urban areas in the southern part of the Province.

Jan 1, 1968

By E. R. Bauer

The ground control aspects and occupational safety concerns of extended depth-of-cut mining are presented in this U.S. Bureau of Mines (USBM) report. The scope of extended cut use and typical face operations while extracting extended cuts is reported. A comparative review of roof fall fatalities and a statistical analysis of accidents and injuries for both extended and nonextended cut mining is included. The views and opinions on extended cutting from a series of interviews with mine workers in five states are summarized. In addition, some of the problems and safety concerns of this extraction system are mentioned.

Jan 1, 1995

By A. E. J. Gallagher

There are many influences which have a bearing on the economics of industrial minerals production. The purpose of this paper is to discuss briefly three factors which have economic significance in the production of these mineral commodities. The three items of discussion include 1) the nature and relative value of the industrial minerals group, 2) project planning, and 3) market analyses. General aspects of these factors are familiar to most of us. However, an attempt will be made to give some current details regarding each. Also, in reality, project planning and market studies are usually so closely associated that they will be discussed jointly, rather than separately. This will be done by way of examples which show how these two activities actually evolved for two industrial minerals projects.

Jan 1, 1984

By R. R. Young

Good afternoon gentlemen. It is always a pleasure to talk about a subject dear to our hearts--the high speed transfer of bull; materials. Specifically, today we will be reviewing the engineering approach to an age old problem of ship loading and unloading. You may be puzzled by the title of this paper and we will attempt to explain this for you--particularly the use of the words "New Era", since high speed automated facilities are nothing new to the material handling engineer. The new era in material handling designs refers to an all out concerted effort to provide custom engineering tailored to specific operations and economic requirements of the client. It shuns hardware type of engineering wherein existing machines and devices are dusted off and reapplied. It provides automation when automation can be justified and it exemplifies the application of systems engineering to solve specific problems.

Jan 1, 1967

By Y. Luo

Although considerable progress has been made in the last decade in predicting surface subsidence over longwall panels, a number of important issues deserve further studies in order to improve the techniques and accuracy of subsidence predictions. Some of the problems are: (1) subsidence over the chain pillars between mined longwall panels; (2) subsidence development process after face stop due to either a vacation or the completion of a longwall panel; and (3) subsidence initiation and development process over the setup entry area in the initial stage of mining a longwall panel. In this paper, the measured data related to the targeted problems are presented, the data analysis techniques are briefly introduced, and some of the prediction methods developed based on the collected data are proposed. The proposed methods can be used as supplemental tools for the existing subsidence prediction models to improve their prediction accuracy.

Jan 1, 1991

By Arthur B. Johnson

Potassium, is one of the three basic plant nutrients along with nitrogen and phosphorus. There is no substitute for potassium compounds in agriculture; they are essential to maintain and expand food production. Potash is found throughout the world in both soluble and insoluble forms. It is only the soluble forms that are economically attractive to process, primarily chlorides and sulfates, with potassium chloride by far the most important potash salt. Sylvinite ore, a mechanical mixture of sylvite (KCl) and halite (NaCl), is a natural mineral of potassium. This ore is found in commercial quantities in the Permian sin region near Carlsbad, New Mexico. Vast tonnages of high-grade de, low-clay-content ores have been mined and concentrated during the past 40 years; however, these deposits are rapidly being depleted leaving high-clay, low-grade ore reserves of over 135 million tons. These ores, containing 13 to 22 percent K20 and 3 to 8 percent clay slimes; cannot be effectively processed by current commercial flotation methods. The present concentration processes for potash minerals in Carlsbad relate mainly to ores containing 1 percent or less of clay-slimes with a K20 content of 20 to 25 percent to yield products to meet the requirements of the agriculture market, namely, 95 percent KC1 equivalent to 60 percent K20. Discoveries of potash ore in Saskatchewan, Canada, have shifted the emphasis on expansion outside the United States. Presently, the American companies are looking to Canada for future growth, expenditures, and expansion. Four of the seven companies operating near Carlsbad are produces of Canadian potash despite the large investment sons required for shaft sinking and milling installations.

Jan 1, 1970

By H. S. Castro

The by-product molybdenite technology in Chile is reviewed. Flowsheets, reagents and some operation features for the actual six Chilean moly plants(Chuquicamata, El Teniente, El Salvador, Andina, Las Tortolas and Pelambres), are presented. The chemical and physicochemical factors involved in the depression of copper and iron sulfides during the selective flotation of molybdenite, with sodium sulfide, sodium sulfhydrate, anamol-D and LR-744, are discussed. Advances in technology to solve problems of excess of lime (precipitation with sulfuric acid); excess of residual flotation reagents (activated carbon and kerosene); and optimization of depressant consumption (Eh control, nitrogen and low-oxygen air), are discussed.

Jan 1, 1998

By Fun-Den Wang

In underground coal mines, three types of roof failure (2)*, tensile, local, and shear, occur in the development entries and in room-and-pillar extraction areas. Most of the tensile failures in the roof at the center of the mine opening as well as those local failures due to fracture or jointing can be controlled by roof bolts, trusses, and timbering. However, control of the shear failure at the sides of the roof (or the cutter-roof caving) has not been successful with ordinary roof control methods. The only effective method, when there is an indication of cutter-roof caving, is to use cribs, which are costly and make transportation, ventilation, and production difficult. Frequently, the operator allows the cutter roof to cave and then cleans it up rather than trying to stop it. This shear type of roof failure is often associated with large areas which may progressively involve several hundred feet of roof caving at one occurrence. At times, this shear failure occurs suddenly with little or no warning. This can result in buried equipment and great danger to the safety of personnel. This shear failure may be due to one or more of the following: high stress concentrations at the corner of the roof from (1) high horizontal to vertical load ratio, (2) orthotropic elastic properties of rock and coal, (3) greater stiffness of the immediate roof layer than of the secondary roof layer, (4) viscoelastic behavior of rock and coal, and (5) geometry and material properties of the geologic setting. Removing or reducing the high stress concentration should improve the roof stability. The structural analyses of models of two typical

Jan 1, 1972

By Richard J. Lundin

Literature research is an inexpensive, yet effective tool for the direct discovery of ore deposits. Case studies abundantly demonstrate that properties with viable mineralization and *proven reserves have been overlooked, forgotten. or ignored and can be rediscovered by inexpensive literature search techniques Areal studies s as WaIlaby Enterprises Mining District Data Base Program appear to be more effective than traditional commodity studies. The success of such studies depends on the inclusion of Mineral Clairant Questionnaire Data, Mineral Ownership Data, Field Examination Data and the continual updating of all information. Such studies are valuable for proposed or existing Wilderness Area Evaluations.

Jan 1, 1977

By D. A. Longhurst

Improper size distribution of the grinding media in a multicompartment mill can be a source of many operation problems encountered. Inefficient use of the power expended for grinding, and an undesirable product size distribution are two frequent resultants. It is necessary to resize the grinding media in the leading mill compartment at time intervals related to the abrasive nature of the material being processed. In practice, this is done when time permits and with sketchy guidelines, if any. Maintenance of the grinding media size distribution can be scheduled, and would be, with a realistic method supplied to the user.

Jan 1, 1984

By R. R. Klimpel

This paper discusses the effect of water chemistry, reagent type, and other environmental factors on the performance of sulfide mineral size reduction and froth flotation processes. Two specific problems will be discussed: 1) the importance of appropriately utilizing the electrochemical window that is created in the grinding process to enhance sulfide mineral recovery by froth flotation; and 2) the impact of steel grinding media versus autogenous grinding on the efficiency of sulfide mineral flotation with varying thiol collectors and water sources.

Jan 1, 1996

By W. Miola

The MSHA prescribed method for the determination of quartz in airborne respirable dust samples from underground coal mines is the P-7 method, a combination of low temperature radio-frequency ashing (LTA) and infrared analysis (lR). There is no prescribed procedure for quartz analysis in bulk samples of coal and host rock. Dispersive Infrared (IR), Fourier-transform Infrared (FTIR), and X-Ray Diffraction (XRD) methods are most commonly used for quartz analysis in powders. Several aspects of the experimental procedures such as the analysis sample preparation from bulk samples, ashing techniques, scanning procedures, peak measurement location, calibration techniques, sample amounts, size consist, and data interpretation affect differently the results from each of the methods. Significant differences in analysis results from X-ray diffraction (XRD) and infrared spectroscopy (IR) on the same samples are reported. All these studies point to the need for reliable quartz analysis methods. In a recent research, a procedure for preparing bulk coal and host rock samples for quantitative quartz analysis was developed. Further the results from X-ray diffractometry and infrared spectroscopy for quartz content on identical samples were compared. Calibrations with pure and mixed standards were used to assess the influence of particle size distribution, matrix, and calibration on analysis results. In this paper, several issues with the measurement of quartz in the samples of coal, host rock, and airborne respirable dust from mines are outlined and quantified.

Jan 1, 1994

By G. P. Larson

We define a specialized mineral market as follows: Specialized Markets are markets where a low volume of a given mineral is used to convey a large benefit to a specific product. Sales of these value added minerals to small markets generally require a different marketing approach compared to bulk or commodity markets for traditional minerals. Specialized and commodity markets are differentiated by several characteristics as listed in Table 1.

Jan 1, 1990

By Issac Douglas, Sheila Devasahayam, John S. Thella, Manoj K. Mohanty, Jeremy Prishmont

The flotation performance of Sodium O, O-diisobutyl Di thiophosphate (referred to as reagent A) was compared with Aerophine 3418A (referred to as reagent B) for floating a complex copper ore grab sample (Ore A). Preliminary test results indicated a cumulative copper concentrate grade of 10.19% with a recovery of 86.31%, which was achieved with reagent A from a feed consisting of 5.32% Cu. The grade and recovery achieved using reagent B are 9.11% and 87.85%, respectively. A comparative analysis based on the preliminary test results indicated that reagent A’s performance is better than that of reagent B at lower concentrate grades, specifically below 12% Cu. However, the flotation performance is better for reagent B at higher concentrate grades (>12% Cu). A more detailed study was conducted to optimize the grade-recovery performances achievable from both reagents on a complex low-grade copper ore sample (Ore B) from Western USA. Test results indicated a copper concentrate with a grade of 5.5% Cu and 78.59% recovery was obtained with reagent A compared to 4.31% Cu and 62.04% recovery with reagent B from a feed consisting of around 0.25% Cu.

Feb 22, 2026

By N. P. Reddy

This paper describes an experimental setup for multiple-fan ventilation systems at the ventilation laboratory of the WVU Department of Mining Engineering. Housed in a 30 ft by 70 ft room, the experimental setup consists of three 18 in. variable-speed axial-flow fans, the 18 in. diameter fiberglass tubing and fittings for arranging networks, and the pitot tube measuring and data acquisition system. The fiberglass tubing and fans can be organized into the non-planner network of two fans or three-fans. It is mainly designed for studying the characteristic curves, operating points, and fan stall for the multiple-fan ventilation system.

Jan 1, 1992

By S. K. Sharma

The Bureau of Mines' Tuscaloosa Research Center is conducting research to develop a basic understanding of solid-liquid separation in order to improve the dewatering of fine particle slurries. In the present investigation capillary suction time (CST) of kaolin slurries was determined. The average specific resistance of the cake was also determined by fitting the CST data to the theoretical equations used in this paper. The experimental data were analyzed by a powerful computer-based method, chemometrics, that uses statistical techniques to remove error and to find the number of physically significant factors contributing to the data. Results showed that two significant factors explain the CST data.

Jan 1, 1991

By S. Chander

The formation of surface films on pyrite has been studied through electrochemical techniques of cyclic voltametry and AC impedance measurements. The characteristics of the surface films depend upon the conditions of oxidation and the source of pyrite. At potentials near 0.0 V, some pyrites have large values of polarization resistance showing a certain degree of passivity. Some pyrites show more passivation than the others, however. On oxidation, metastable phases of Fe(OH2) and Fe(OH3) form which transform to more stable 3 phases on aging. The growth of surface films near the corrosion potential of pyrite follows a linear kinetics which is attributed to a chemical (or an electrochemical) reaction as the rate determining step. The surface film is considered to be a hydroxide or an oxide rather than sulfur because the later is expected to be limited to a monolayer in alkaline solutions. This study has also demonstrated that AC impedance measurements can be used to study the growth characteristics of films at mineral/ solution interfaces.

Jan 1, 1987