Search Documents

By Y. C. Kim

An alternate development drilling strategy to the one currently in use at the nine was investigated using geostatistics for a portion of the pit. The study area consisted of 4,000' x 5,000' in plan and 1,080' in elevation. The massive orebody, the three-dimensional nature of the problem, and the location of ultimate pit limit in the study area all created some unique problems in devising the development drilling strategy, as compared to the two-dimensional tabular deposits such as coal deposits. Rather than using the confidence interval of the global reserve estimate as the main criterion for development drilling, the confidence interval of short and medium range mine planning blocks was used as the objective. Based on somewhat arbitrarily selected level of confidence, the results from this study showed that a total of 50 DDHs rather than the planned 62 DDHs is sufficient in the study area, if the selected confidence levels are acceptable to the management. This paper also emphasizes the importance of the particular objectives being used in development drilling and how they influence the "optimai" place- ment of the development drill holes.

Jan 1, 1981

By L. M. Turner

Perlite is a unique mineral that upon heating expands to about twenty times its original volume. Mining is by open pit method. The processing cycle involves crushing, screening and sizing the ore. An on-site quality control facility at the Manville Products No Agua mine exerts a high degree of control over every phase of the operation from blasting to finished product.

Jan 1, 1985

By Irwin H. Reiss

Gentlemen, the title of my paper is Surface Mining An Interim Land Use. Surface mining has become one of the major controversies of our time. This has happened in spite of the fact that all surface mining to date has involved only 6 million acres out of a total of 2300 million or approximately one-fourth of one percent of the total land area in the United States. I'm not going to dwell on whether peoples' perspectives are out of focus in light of the area involved, the energy crisis, national security, or the international balance of payments problem. While these things are all critically important, it is not the function of this paper to relate to them. Maybe the amount of attention attracted to surface mining is out of proportion to a lot of other things, but I don't feel that we should use that as a basis for procrastination. However, let me categorically state that anything that affects the surface of the earth is a form of land use --- be it an interstate highway, a power plant site, a golf course, a corn field, a strip mine, or the plot of ground on which your house is located.

Jan 1, 1974

By Lee A. Goetz

Cost control is a lot like motherhood - everyone proclaims its need and its worthiness, but is it really appreciated and used to successfully complete a project on time and within budget? Good Cost Control is a yardstick - requiring fixed definition but this does not mean rigidity for the project. It provides the means for telling: 1. Where you are going 2. When you will complete and 3. What it will finally cost. Cost Control does not fix the price of dreams nor the cost of projects loosely defined. It does not control costs in itself but provides the tools whereby engineering decisions can be made which will ultimately affect the project cost It does not even guarantee that a project will be completed within the original funds - but only, if this reflects management desires.

Jan 1, 1970

By Paul Soros

The rationale for innovations in two directions is identified: raising capital and annual throughput, in order to avoid the cost of constructing and operating an additional system and to reduce the capital cost of pits and tunnels, applicable to installations of any capacity. Cast histories cover railroad unloading of bottom dump cars, rotary dumping of random cars, with and without indexer, and unit trains as well as truck unloading of multiple grades of coal.

Jan 1, 1985

By H. F. Haller

Large volume sand plugs are placed in tunnels to stem underground explosions at the Atomic Energy Commision's Nevada Test Site. Placement through long, narrow accessways is like stemming coyote holes and blast chambers in mining and construction. Experience with several other methods showed that pipeline conveying could be preferable. Small scale tests justified predicting a placement rate of 20 y. p. h. at 1000 feet, with a modified gunite placer. The initial production trial placed over 2000 c. y. and was estimated to effect a small cost saving after paying for new equipment. Initial problems included duct replacement and supply delays, dust, and other personnel hazards. Operations analysis and SOP'S reduced delays during the second field trial, minimized hazards, doubled production. Re cent re search and operations analyses produced data on abrasion resistant ducts, identified minor equipment modifications which can improve production, developed techniques for impact compaction to 90% ?maximum? and for extension of the practical range to 2000 feet. Twenty-two illustrations include an air consumption-distance chart.

Jan 1, 1967

By Charles W. Merrill

The price records of 7 representative mineral commodities for the 68-year period 1890 through 1957 have been compiled and analyzed for significant trends. When reduced to real prices in terms of dollars of constant purchasing power or to the purchasing power of industrial wages at average rates, a substantial overall fall in prices is revealed. This downtrend contradicts the widely held concept that, heavy drafts on a mineral resource must lead to scarcity, reflected in rising prices. Three metals (aluminum, copper, and pig iron), two fuels (bituminous coal and petroleum)', and two nonmetals (sulfur and cement) have been chosen because of their preeminence in their respective categories, their significance in an industrial economy, and the ready availability of their price records. It might be added that these seven commodities. were selected before any price figures were compiled, none was selected or rejected to substantiate any preconceived notions as to price trends, The overall importance of the seven is demonstrated by the fact that, taken together, they composed over three-fourths of the value of all minerals produced in the United States in 1957. The first step in the analysis was to reduce the price records to a basis for significant comparisons, Two such comparisons have been made: (1) The quantities of each of the commodities that could have been purchased for an average hour's wage in each year; and (2) the unit price of each commodity through hhe years in terms of deflated dollars. These data are set forth in the accompanying table and two charts.

Jan 1, 1959

By K. T. Mau

Hawaii is located approximately 2,500 miles from the mainland, but has basic needs for its thriving developing community. Cement is one of these needs Cement production in Hawaii is not without handicaps. The necessary raw materials are practically non-existent except for limestone. Even at that, the available limestone is marine in origin, coralline in nature and amorphous in characteristics - unlike calcite which is normally the calcium carbonate source for cement manufacture. There is no clay or shale for the argillaceous portion of cement raw mix. Hawaii being volcanic in origin is too young geologically for clays and shales to evolve and whatever there is, most likely is washed into the ocean.

Jan 1, 1982

By Dennis A. Fenton

This paper presents some techniques and data required to design large ball mills. The advent of larger size mills leads to consideration of the gearless drive as a practical solution to utilize large horsepowwers. The particular shell structure under consideration is subjected to thermal as well as magnetic loads. The magnitude of the inertia, magnetic and shell temperature characteristics have a very significant effect on the design and performance of the hydrodynamic pivoted shoe bearing. Particularly since these bearings have lower frictional resistance properties than hydrostatic trunnion tee rings. The structure of the mill is designed for long life. Parameters involved with the fatigue life of the structure are discussed together with some of the more important aspects of the design.

Jan 1, 1975

By Rolph Linder

It is generally known and accepted that the efficiency of the blast furnace process, expressed by the symbols specific production and coke consumption, is influenced by a large number of variables connected to the type of burden, the alloy contents of the produced iron and the conditions of production as composition and preheating of the blast, the furnace heat losses and the possible use of fuels added on the tuyere level. It is furthermore obvious, that the coke consumption of the process will be influenced by specific production which could be said to be the result of two counter-acting influences. With high production, realized through intensive blowing, the passage time of the ore through the furnace is shortened leading to a decrease of the indirect reduction taking place in the upper part of the shaft within the temperature range of 300 to 1000°C. Simultaneously the external heat losses (constant in time) will be smaller calculated on each ton of iron and the resulting change in coke consumption will be the effect of both those influences. It is certainly of interest to be able to predetermine the effect of those variables before a change in the production practice is carried out.

Jan 1, 1964

By D. Loy LeRoy

As we are all aware, the impacts of the 1977 Surface Mining Act and the implementing OSM Regulations require application of new, as well as existing, equipment and technologies. Our firm recently completed (June, 1979) a study for the Department of Energy titled "Analysis of the Impact of Public Law 95-87 on Mining Performance." The objective of the study was to analyze the impact of the Act and its regulations on mining performance in order to provide recommendations to alleviate the impacts identified, including identification of research needs. This paper presents some of the highlights of that report: projected cost increases; additional equipment needed for compliance; review of methods currently practiced or those which can be modified; and will focus particulary on equipment and technology applications.

Jan 1, 1980

By Doug Brown

The recent expansion of our cities into hilly areas, particularly on the Pacific Coast, has resulted in damage or destruction of many homes due to geological problems such as landslides, soil creep, erosion, subsidence, or groundwater seepage. In southern California, landslides are the principal cause of damage and attention is focused on them. Landslides have occurred due to the reactivation of old slide masses, or have been caused by grading and increased water, infiltration resulting from development.. Reactivation of a portion of the ancient Portuguese Bend landslide in Palos Verdes, Los Angeles County, affected approximately 150 homes. A common type of new failure' occurs when grading has undercut bedding or other essentially planar surfaces so that they dip unsupported out of slope. Other slides have occurred due to the inherent weakness of the material involved. Preventive measures undertaken to eliminate damage in the southern California area have. included areal geologic mapping programs-in-advance of development, enacting or strengthening grading codes, and requiring extensive studies by consulting geologists and soils engineers both during the design stage and during construction. In the design stage, proposed cuts are frequently flattened, lowered or reorientated. Frequently, due to the high cost of land, they are supported by compacted fill buttresses. As a result of these measures, the geologic environment has a major effect on the feasibility, design, and development of, a very substantial percentage of tracts or individual homes.

Jan 1, 1967

By Henry W. Brandt

What is the most practical method for storing a huge quantity of crude oil for a long period of time to assure availability if conditions curtail the source of supply? Underground storage is a logical answer. But can abandoned mines be used for this purpose? That is the proposal Fenix & Scisson International, Inc. submitted to the S.F.F. Association (acting in behalf of the Department of Industries of the Republic of South Africa), Johannesburg, South Africa, in October 1966. This engineering and contracting firm with headquarters in Tulsa, Oklahoma, specializes in underground storage; and based upon previous experiences their engineers were reasonably certain that a mine could be used for storing crude oil. The answer subsequently proved to be "yes." The result was con- version of a coal mine to provide storage for a quantity of crude oil which is the equivalent of a sizeable oil field. The total cost of purchasing, testing, and converting the mine was less than 15 percent of the cost of conventional steel tanks. Operating and maintenance costs are proving to be about 2 percent of those experienced at two large tank farms owned and operated by the Association.

Jan 1, 1973

By Tegner C. Johnson

Just a few years ago my company was referred to as the Marion Steam Shovel Company. We still make shovels, both two and eight crawler types. The eight crawler stripping shovel appears to have been replaced by the walking dragline for overburden removal and in some cases for the mineral as well. The walking dragline appeared in the coal fields in the early 1930's. It owes its popularity today to the fact that it can cope with overburden depths in excess of 100 feet and with blasted sedimentary rock, all at an 0 & 0 cost of ± 10¢/BCY.

Jan 1, 1974

By Lawrence P. Bonicatto

The steel industry's increased demand for higher grade pellets has caused the pellet producers to investigate methods of upgrading their product. The Hanna Mining Company's Groveland plant is no exception. The Groveland Mine is located in Dickinson County on the Upper Peninsula of Michigan. The low grade iron deposit is a complex mixture of magnetite and hematite with chert, quartz, jasper, and various iron silicates. (1) Beneficiation is by Humphrey spirals and anionic flotation of the iron minerals. (2) A general flowsheet is shown in Figure 1. Flotation of the spiral tailings makes up about 75% of the concentrate. A minor amount of concentrate, less than 3%, is produced in magnetic circuits. The concentrate is pelletized at the rate of 1.6 million tons per year.

Jan 1, 1968

By E. G. Williams

Underclays and shales are two natural resources associated with the coal measures. Underclays are widely used as the raw material for refractory, semi-refractory, and face bricks. Shales are useful for sewer pipe and lightweight aggregate. This study concentrates on the geologic controls over the properties of shales for use in the manufacture of lightweight aggregate, and the geologic controls over the properties of underclays for use in the manufacture of bloating ladle refractories. The industrial processes are similar in that both involve the trapping of a gas phase to cause bloating. They differ in that the bloating of lightweight aggregate occurs at lower temperatures (1000-1200°C) than ladle bricks (1350°-1470°C). Lightweight aggregate bloats during an initial rapid firing. Ladle bricks are manufactured by slow firing at 1100°C for up to 80 hours. Bloating occurs when these bricks are reheated to 1350°C . Bloating shales are those which expand twice or more times their original volume during fairly rapid firing. Commercial bloating is usually done by rotary kiln processing or sintering; in both cases the firing rate is much faster than the experimental rate (5/8°C/minute). Bloating results from the entrapment of gasses which are evolved during firing. The material must have adequate viscosity to trap gas bubbles throughout the temperature range of bloating. The finished product contains a high percentage of closed pores with a bulk density between 35-75 pounds per cubic foot. Expanded shale finds its most important use as a substitute for heavy concrete aggregate (crushed stone, sand and gravel) where low bulk density is desired property. The extent of bloating in lightweight aggregate is a function of the mineralogy and chemistry of the shale. Figure 1 shows a corner of the three phase diagram, kaolinite-quartz-(illite and chlorite). Several areas on the diagram are outlined which contain predominantly marine shales, fresh and brackish water shales, and underclays. Each sample was rapid fired and the resulting expansion was plotted on the phase diagram.

Jan 1, 1973

By H. G. Fleshman

Thousands of years ago, Chinese water well drillers developed a technique for punching holes in the ground by lifting massive metal bits and letting them fall against the rock. With diligence, they could pound away about 2 feet a day. The Chinese drillers pounded holes in the ground this way for almost 2000 years. In the 1860's, French water well drillers developed a perforated bit moistened by fluids pumped into the hole through a hollow rod. The fluids carried the cuttings from the hole and spared the Frenchmen the task of bailing them out by hand.

Jan 1, 1986

By U. S. Sawant

During the last few years, Process Machinery Division, Rexnord, has conducted extensive research on the effects of cone crusher variables such as speed, throw and cavity design on the productivity of the crushers. Simultaneously, Rexnord's engineers have developed advanced design and testing techniques and criteria that assure efficient and reliable crusher designs. The combination of these two has resulted in a design of the 2390 Omnicone (1000 hp) crusher which fits on an existing 7 ft. Symons foundation and yet is capable of producing twice the tonnage compared to our 7 ft. super heavy duty (500 hp) crusher. Both speed and throw can be varied to give a wide application flexibility from making twice the tonnage to the finest product. The 2390 Omnicone also incorporates innovative features such as full balance, cavity clearing, adjusting under load with automation capability, maintenance-free seals, one head for all cavities, ease of maintenance and servicing, etc.

Jan 1, 1987

By V. W. Smith

For the past 50 years, the primary crushing of stone at the Dolase Bros. Co. Richards Spur Quarry. 13 miles north of Lawton, Oklahoma, has been accomplished by a Traylor 42-inch gyratory crusher. The production capacity of the primary system, consisting of a feeder, grizzly, and the gyratory crusher, was approximately 2100 tons per hour. Shot-down scone was hauled from the working face about one mile to the feeder by a fleet of Caterpillar Model 773's and WABCO 60- and 65-ton trucks. In order to maintain production, nine to ten trucks and four Caterpillar Model 992 front-end loaders were required to be operational at all times.

Jan 1, 1986

By H. G. Fleshman

The economics of western sodium bentonite (also known as Wyoming Bentonite) is covered from exploration to delivery to the final user. Included are costs of exploration, evaluation of ore bodies, mine permitting, stripping, loading, hauling through stockpiling, blending, processing and shipping. Since western bentonite is one of the industrial minerals marketed throughout the world, the various markets and freight costs are included.

Jan 1, 1984