Search Documents

Simulation models were developed at the Julius kruttschnitt Mineral Research Centre to provide accurate estimates of power consumption for a wide range of equipment. With the models, a range of circuits and operating conditions can be compared by simulation for a particular ore type. Accurate models of classification allow for the interaction between classifier efficiency and target product size (e.g., P80 or percent passing 150 /an) to be considered. This paper considers a range of circuit types and overall energy efficiency in the context of case studies where different circuit types were treating similar ore types.

Jan 1, 1999

By Y. Luo, S. S. Peng

This paper presents some results obtained from research on long-term subsidence over and near chain pillar systems - the area available to long-term subsidence in longwall operations. Although the long-term subsidence for most longwall operations is insignificant, it does exist in some cases. In the cases that showed significant long-term subsidence, it was found that the development process could be expressed by an exponential decaying function. The stability factor of the chain pillar system and the potential for long-term subsidence are the two most important factors that control the magnitude and development characteristics of the long-term subsidence process.

Jan 1, 2000

By Veliko Kertikov

Complicated processes of heat exchange and evaporation, leading to changes in the temperature and humidity of the ventilating air flow, take place during the driving of headings. In the case when virgin rock temperature is high, the increase in air temperature and humidity is significant. This causes a deterioration of climatic conditions in the headings. Procedures for predicting the changes in air temperature and humidity are discussed, together with appropriate calculations and computer programmes. Predicted results for example scenarios are used as a background for the selection of approaches and means to improve the climatic conditions in a dead-end heading using auxiliary ventilation.

Jan 1, 1997

By C. K. Nworu, L. O. Asuquo, C. O. Nebo

Selective flocculation studies of Agbaja iron ore with starch-type and nonionic polyacrylamide-type flocculants has been conducted to determine the effect of flocculant type. The results indicate that corn starch was slightly better than cassava starch in selectivity performance. Cassava starch was in turn better than Superfloc 16, while the poorest results were obtained with commercial starch. Sodium humate shows better dispersive capability, and thus enhanced flocculation results, than sodium silicate. Pulp pH affects the zeta potential, polymer chain configuration and hence selective flocculation. Overall results indicate that recovery and separation of this very fine grained iron oxide by selective flocculation is feasible.

Jan 1, 1995

By E. J. Dorward-King, R. J. Kadeg, S. Pavlou

Risk assessment, risk management, and engineering/economic feasibility analysis are presented as three effective, practical tools for decision making in the remediation of contaminated soils. Risk assessment is applied to evaluate the extent, magnitude and sources of contamination, to identify appropriate contaminants of concern (COCs). Risk management is then applied to identify the acceptable contaminant residual levels for the COCs. Finally, engineering/economic feasibility analysis is used to define the appropriate cost-effective remedial action and associated target contaminant action levels that will achieve the acceptable contaminant residual levels. A real site application of this decision making approach is presented. This site illustrates that through appropriate engineering, acceptable risk-based contaminant residual levels can be achieved with higher action levels.

Jan 1, 1992

By A. M. Tunstall

Blasting is commonly viewed separately from mechanical handling and crushing. This view is misleading because the degree of fragmentation achieved by blasting can have a significant effect on the efficiency of these processes and, hence, on the overall cost of the mining operation. In this paper, aspects of blasting and crushing and their interaction are examined. A case study is also presented that dramatically illustrates the influence of blast fragmentation on subsequent processing and on the financial implications involved.

Jan 1, 1998

By J. C. Cawley

Improvements in today's maintenance practices are mandatory as more complex and productive machines evolve in the mining industry. By keeping machine reliability high through improved maintenance procedures, overall mining costs can be reduced. The Bureau of Mines is investigating diagnostic maintenance systems for underground mining machinery. A hydraulic expert diagnostic system and an electric motor predictive diagnostic system have been designed and installed on a Joy 16CM continuous miner. An electrical diagnostic system has been designed and installed on a Joy 14CM continuous miner. Each system is functionally described and the relative merits of expert diagnostic systems versus algorithmic diagnostic systems are discussed.

Jan 1, 1992

By S. L. Bolivar

The Prairie Creek intrusion, near Murfreesboro, AR, is the site of the most famous diamond mine in North America. Three major rock types are associated with the intrusion-a hypabyssal peridotite, a volcanic breccia in which the majority of diamonds occur, and tuft. Previous studies, including geological, geophysical, petrological, and whole-rock and mineral chemistry are reviewed. The recent suggestion, by other workers, that this intrusion may be more correctly called a lamproite is examined. This has serious implications for diamond exploration in Arkansas and elsewhere in the US.

Jan 1, 1987

By Gerald H. Luttrell, Roe-Hoan Yoon

Flotation columns are becoming increasingly popular due to their ability to improve selectivity and to reduce operating costs. Unfortunately, these advantages are not often realized because of poor operating practices and difficulties associated with design and maintenance. This article provides guidelines for the operation and design of columns. The discussion will focus on designing proper wash water systems for improved selectivity, maximizing throughput by increasing the bubble surface area rate, and minimizing operating and maintenance costs. It is suggested that the design of the air sparging system is the most critical element in column flotation.

Jan 1, 1993

By J. D. Raulerson, R. P. Farias, G. A. Gruber

A flotation process has been developed to successfully treat ore from the Santo Domingo phosphate deposit in Baja California Sur. The ore contained less than 4% P2O5 with quartz, silicates, and carbonates as gangue minerals. Flotation of the low- grade feed in seawater required that the conventional Crago process, comprising direct anionic flotation, deoiling, and inverse cationic flotation, be augmented by an anionic cleaner flotation step, phosphate depression, and a calcite flotation step.

Jan 1, 1988

By R. W. Smith, S. A. Davis, A. M. Raichur, M. Misra

The flocculation of coal is typically accomplished by the addition of commercially available polymeric flocculants. Recently it was shown that biopolymers derived from microorganisms can also be used. The biopolymers flocculate coal efficiently and make the coal more hydrophobic. This increase in hydrophobicity can be utilized to separate coal flocs and can be used for reducing the moisture content of the flocculated coal. In this regard, flocculation and settling tests using biopolymers and synthetic flocculants were performed on fine coal. The experimental results are discussed and a transport model is presented for the time-dependent settling of fine coal.

Jan 1, 1998

By D. G. Fredlund, J. A. Wilson

Conventional disposal of waste rock results in the construction of benches with fine and coarse layers dipping at the angle of repose. This interbedded structure influences flow pathways within the waste rock. A numerical modeling program was conducted to study a four-layer system consisting of alternating fine and coarse waste rock. The system was inclined from the vertical to forty-five degrees with heights varying from one to twenty meters. The results show the effects of gravity as preferential flow developed under unsaturated flow conditions.

Jan 1, 2000

By P. Tsang, S. S. Peng

Mine floor failures, such as floor heave and floor buckling, occur frequently in underground coal mines where soft mine floor exists. The types of failure can usually be classified into two categories; shear punching failure and tensile failure. A model based on the Winkler's elastic foundation is proposed in this paper for floor stability analysis. The model considers material properties of floor strata, in-situ horizontal stress, pillar size, entry width, and configuration of multiple-entry system and predicts stress conditions in the mine floor based on given in-situ mining and geological conditions, as well as deformation of the mine floor. This information is used to predict possible failures of mine floor by comparing the strength of mine floor with its stress condition. The validity of the model is verified by in-situ data described in this paper.

Jan 1, 1992

By L. J. Laughlin

The majority of non-drive conveyor pulleys use rotating shafts, and typical idler rolls use non-rotating shafts, even though both products are used to support and guide the conveyor belt and its load. This paper will explore and compare the requirements for rotating and non-rotating shaft designs and the impact of that design on the product. Additionally, it will explore how the “roller” bearing types (deep groove ball, tapered, or spherical) affect these designs.

Jan 1, 2003

By Gordon C. Gutrath

Queenstake Resources Ltd. has been exploring and mining alluvial gold deposits in the Yukon Territory and British Columbia since 1980. The five mines in production produced, in 1987, a total of 13,222 ounces. This paper will briefly review Queenstake's exploration program, property descriptions and mining methods, environmental concerns and a comparison of costs. (Sueenstake has been successful in developing a cash flow base from these operations that provide the capital for the acquisition and exploration of new, and hopefully, larger scale gold producers. NOTE: The historic alluvial mining unit of ounces per cubic yard and English units of measurement have been used throughout this paper. Dollars are Canadian unless otherwise noted.

Jan 1, 1988

By B. C. B. Pretorius

A heat load analysis of the very hot sub-shaft area of Loraine gold mine situated near Welkom, South Africa, showed. that the heat that needed to be removed to give acceptable wet-bulb temperatures at the working faces could not be done by the normal ventilation air alone, but would have to be complemented with extensive refrigeration. The paper outlines the considerations in selecting the cooling system adopted for this shaft.

Jan 1, 1980

By Olice C. Carter, B. J. Scheiner

The Bureau of Mines investigated the removal of two toxic/heavy metals (cadmium (Cd) and lead (Pb)) from brass foundry wastewater. Polymers, copolymers, guars, and gums were used in conjunction with calcium hydroxide (Ca(OH)2) and magnesium oxide (MgO) to remove the metals from solution. Several polymers were successful in removing Cd and Pb from the wastewater. The concentrations of Cd and Pb were lowered from 19 to 0.01 ppm and from 20 to less than 0.01 ppm, respectively. The methods investigated could easily be adapted to many existing wastewater treatment facilities and/or be used independently.

Jan 1, 1991

By Harold D. Taylor

Cone fitting is a procedure which can be used to estimate the short range, linear portion of a variogram. Rather than combining data over windows In different directions and fitting by hand, cone fitting estimates the variogram in all directions at once using a multiple regression approach. The method automatically provides estimates of nugget effect, anisotropy, and initial slope of the variogram. This paper presents the results of simulation studies which have been carried out. These studies Indicate that the method works well and that it may be particularly useful for small data sets. The simulation studies also indicate that the local variogram may differ greatly from the theoretical variogram.

Jan 1, 1986

By Giuseppe Bonifazi

This study examines the problems involved with the control of characteristics of the products resulting from comminution operations. A methodology of investigation based on texture analysis procedures by image processing techniques of the comminution product is proposed. Some examples of applications are considered with particular reference to comminution products of different textural, structural and mechanical characteristics. The advantages and the limites of this method of approach are, indicated, both as regards performance of the investigations and subsequent processing of results.

Jan 1, 1989

By W. H. McDonald, D. D. Carr

The use of stone in building construction predates written history. From the time that stone was first used, builders have constructed stone buildings predominately from local or regional materials. However, since World War II, the stone business has become increasingly global. For example, French limestone is now sold to builders in the United States, and American granite is shipped to Japan. The internationalization of architectural and construction firms has encouraged this trend. Differences among nations in trade practices, environmental demands and the level of knowledge of dimension-stone characteristics make international trading in stone a risky and potentially disastrous business for unwary participants.

Jan 1, 1997