Search Documents

By Guanghui Li

Nickel pig iron (NPI), used as a substitute for electrolytic nickel, is able to reduce the production cost of stainless steel greatly. Aiming for preparing NPI from nickeliferous laterite ore, a pilot-plant scale test of coal-based rotary kiln direct reduction of laterite ore was performed and reported in this study. In this process, the ground laterite sample (18.85% TFe and 1.52% Ni) mixed with additives, pulverized coal and binder was briquetted into briquettes with the size of 40mm×40mm×31mm, laterite ore briquettes and reducing coal were charged into a rotary kiln with the diameter of 1.6 m and the length of 16 m, for a retention period of 6~7 hours, in which reduction section temperature was ranging from 950~1050 oC. The reduced briquettes were water quenched, ball mill ground and beneficated via low intensity magnetic separation. A magnetic concentrate, Ferronickel powder, with 86.9% TFe and 8.0% Ni was obtained, and the corresponding magnetic recovery of iron and nickel are 75% and 96.3%, respectively.

Jan 1, 2014

By Guangliang Wu, Dong-chang Huang, Xin-bin Liu

High temperature mechanical properties of 50Cr5MoV roll steel was investigated by Gleeble 1500 thermal simulator testing machine The morphology, composition and microstructure of fracture surface were observed and analyzed by OM, SEM and EDS The results are indicative of that, there are two brittle temperature zones of 50Cr5MoV roll steel at the temperature of 600°C~950°C and 1300°C~1450°C, respectively. The section shrinkage rate is less than 60% The fracture mode changes from mixed ones dominated by intergranular to toughness transgranular one with the increase of temperature at the range of 650°C~1300°C. The fracture is along the solid--liquid phase at the range of 1300°C~ melting point It is crucial to formulate the 50Cr5MoV casting technology, to prevent the cracks and improve the quality of 50Cr5MoV roll steel.

Jan 1, 2016

By W. Gutmannsbauer

Thin films of TiO2 nanoparticles have been prepared by different reactive deposition methods, such as electron evaporation, ion plating and ion beam sputtering. Many properties especially the optical properties, are strongly related to the film morphology and surface roughness. Scanning force microscopy was employed to obtain information on the surface structure of as-deposited Ti(h thin films. The influence of the deposition conditions and the film thickness on the optical and structural properties has been investigated. The as-deposited films were found to be amorphous or polycrystalline with anatase structure.

Jan 1, 1995

By Thomas Niehoff, Yin Qing, Wei Zhongling, Liu Yongguo, Zhang Deliang, Tang Le

The gold ore of Shandong Gold Mining (Xinhui) was a refractory ore, which contained multi metallic sulfides (ZnS and PbS etc.) and carbonaceous. The gold ore concentrate came into leaching process and thickener and zinc replacement to recover gold. In order to improve gold recovery, the GOLDOX™ hydrometallurgy process was studied in Shandong Gold (Xinhui) by bench scale and 6 month plant scale test supported by Linde Gas. It was shown that the process promoted the leaching kinetics and improved gold recovery. The residue grade reduced 0.22 g/t in average after oxygen was applied. This indicates an operating profit increase 850,000 yuan/a in the plant. It was setting a good example for similar gold mine plant and would promote the oxygen application in Chinese gold mining industry.

Jan 1, 2015

By Wenjun Duan, Qingbo Yu, Qin Qin, Junxiang Liu

In the study, the coke-oven gas (COG)-steam reforming process using hot blast furnace slag (BFS) as the heat carrier is explored for producing hydrogen and recovering high-grade waste heat of hot BFS. The method of the Gibbs energy minimization approach through Lagrange multiplier is adopted in the thermodynamic analysis of reforming process. The simulation is carried out to study the operation pressure, temperature and steam to carbon ratio (S/C) based on the chemical equilibrium calculations. The optimal operation conditions are determined to improve the yield and fraction of hydrogen in the COG-steam reforming process. The results suggest that the preferential operation conditions for COG-steam reforming process to produce hydrogen are achieved at 600ºC, 1.5MPa and S/C (5.0). Due to the CaO and other melts in BFS, CH4, CO and CO2 in COG are converted and removed efficiently, especially CO2. The hydrogen fraction reaches to 86.7% and its production is about 1.22mol with 1mol of the COG.

Jan 1, 2016

By J. Lui

The 15m high Inco flash furnace uptake was designed as a reaction chamber with the objective of destroying the H2S contained in the furnace off-gas by combustion with oxygen at about 1300?C. Until recently, the oxygen required for this purpose was injected through afterburners located at the bottom of the uptake. An undesirable side effect of this practice was the formation of build up accretions on the inside walls of the uptake. This buildup had a negative impact on both the furnace on line time and the control of the flash smelting process. In late 200 I, the afterburners were relocated to the roof of the uptake. As a result, about 80% of the uptake accretion buildup disappeared with obvious beneficial effects for the operation of the furnace. This paper discusses key flash smelting aspects that affect the operation of the flash furnace uptake such as the dusting rate, the formation of H2S in the freeboard of the furnace, and the impact of using coke to supply some of the heat required by the process. The mechanism of buildup formation and its dependence on uptake afterburners location are also examined. Prof. Yazawa's sulfide smelting thermodynamic relationships proved instrumental in understanding the conditions that influence the formation and the elimination ofH2S and uptake buildup.

Jan 1, 2003

By Carlos M. Fontes Vieira, Ruben J. Sanchez Rodriguez, Carlos E. Gomes Ribeiro

"In this study we attempted to model a response surface for the apparent dry density of ternary blends of calcitic marble particles. The crushed marble was divided into three granulometric ranges. Simplex network methodology was used to determine the mathematical relation between granulometric ranges and apparent dry density (ADD) of particle mixtures. A highly significant regression was obtained and the simplex network methodology proved to be able to predict high packing particle compositions.IntroductionProblems with packing and expected porosity of particles are common and widely recognized to be important in terms of both fundamental physics and engineering applications. For example, densification of a powder mass is important in the shaping of solids in ceramics, powder metallurgy or composite synthesis; chemical processes such as solid-liquid separation (sedimentation, thickening and filtration), raw material handling (stockpiling, blending, drying, storage and transportation) and pyrometallurgical processes (agglomeration, coke making, ore sintering, blast furnace iron making and new iron making processes) [1,2].Many factors can affect particle packing, but in practice, there are three main factors: (dimensionless) particle size distribution, particle shape and absolute particle size [2].Geometrical and practical methods were developed to predict properties in mixtures. Zou, Gan and Yu [2] present a paper treating a prediction of the porosity of multi-component mixtures of cohesive (fine) and non-cohesive (coarse) particles. Bahiense et al. [3,4] used a simplex network to determine a mathematical model for obtain the optimal compositions between aggregates to a greater packing of a ternary particles mixture. Despite these techniques for predicting particle packing, some studies in particulate composites production don't present clear criteria for choice of particle distribution [5,6]. As the best particle packaging depends on the size, distribution and shape of these particles, individual models can be constructed for specific combinations of these factors."

Jan 1, 2014

By Y. Suzuki, J. Nagao, Y. Ueda, K. Shimokawa

"A Ti- Ni intermetallic compound could be formed rapidly from Ti and Ni powder compact with SHS process. Microgravity experiments using a drop shaft are carried out, This report shows the effect of microgravity or high gravity on formability of an intermetallic compound. It is concluded that the specimen forms a porous and nearly amorphous alloy by rapid cooling under microgravity but with rapid cooling under high gravity after microgravity, the specimen forms a uniform and dense structure with better crystallinity.IntroductionTi - Ni inter1etallic co1pounds have been produced and have beco1e si1ilar to the a1orphous and porous structure as a result of the SHS (Self Propagating High-te1perature Synthesis) process under 1icrogravity. SHS process is being applied to the synthesis of cera1ics and inter1etallic co1pounds (1). The technique is characterized by a large a1ount of heat being emitted within a very short ti1e interval as regards the sistering reaction. One SHS process, acco1panying 1elting by a reaction was observed, and that was due to the quick heating of a Ni-Ti co1pact containing 50 ato1ic percent of Ti under a low pressure (2-4). In this report, we have researched the use a drop shaft which is 1ore effective during a short ti1e under 1icrogravity and high-gravity, so as to obtain high dense speci1ens with the exception of porous specimens (5). Mechanical properties of each specimen were esti1ated from these 1icro-structures with a discussion about the effect of changing gravity regarding 1elting and solidification of the Ti-Ni intermetallic comounds."

Jan 1, 1996

By Xiaoyan Xiang, Wenqiang Yang, Wentang Xia

Magnesium aluminate spinel is widely used in the metallurgical industry as refractory material, however, natural magnesium aluminate spinel is rare and most of the magnesium aluminate spinel is synthetic. The traditional synthesis of magnesium aluminate spinel often needs high temperature, which leads to more energyconsumption. In this article, solid phase sintering process was employed to synthesize magnesium aluminate spinel, in which, magnesium and aluminum oxide were used as raw materials and magnesium and aluminum powder were used as composite additives. The mass ratio of magnesium and aluminum on the effect of synthesis of magnesium aluminate spinel and the characteristic of the synthesis at different temperature and time was discussed. Experiment found that the synthesis temperature was observably lowered when the addition of magnesium and aluminum was 2.0% and 1.0% respectively.

Jan 1, 2016

By Guo Chen, Jin Chen, Jinhui Peng

"In this paper, the methods of life cycle assessment for microwave hot air systems, and the concept of green degree were proposed. Greenness evaluation index, evaluation system and evaluation model of microwave hot air systems were established. Also, life cycle assessment processing based on these ideas was introduced. Analytic hierarchy process and fuzzy decision- making method were utilized to establish and solve the greenness evaluation of assessment model, while the scores of green degree in microwave hot air systems were obtained. The results show that Life cycle assessment can be applied effectively and efficiently to the microwave hot air systems.IntroductionHot air systems are an important industrial operation condition, which is used to provide high temperature air for materials processing. Nowadays, high temperature airs are manufactured by the conventional heating processes, in which some ceramic materials are used as heating materials. However, these processes pollute the environment. Therefore, to explore new method to produce high temperature air with low energy consumption and less environment pollution are necessary.Microwaves are now being used in various technological and scientific fields in order to heat dielectric materials [1]. Microwaves irradiation has been explored in materials processing in recent years [2-3]. The main advantage of using microwave heating is that the treatment time can be considerably reduced, which in many cases represents a reduction in the energy consumption as well. Since there is energy absorption but no heat conduction, the heating is very rapid and highly efficient, resulting in energy savings and the shortened processing time [2, 4]. Compared with conventional heating techniques, the additional advantage of using microwave irradiation is that microwave irradiation achieves both internal and uniform heating [5-7]. In addition, it is more convenient to control the microwave irradiation processing, because of no direct contact between the heating source and heated materials with less equipment size and waste [2, 8-9]. Life cycle assessment is used and accepted methods for the evaluation of the environmental impacts of products or systems [10]. Recently, many appropriate evaluation methods have been developed for life cycle assessment [11-12]. These proposed methods usually are employed for the evaluating product and analyzing results [13]. Among them, the analytic hierarchy process and the fuzzy comprehensive evaluation stand out as a popular method utilized in many fields [14-16]. Analytic hierarchy process and fuzzy comprehensive evaluation are a combination of mathematical and statistical technique that is useful for analyzing the effects of several independent assessment aspects on the system goal without the need of the predetermined relationship between the objective function and the assessment aspects [17-19]."

Jan 1, 2013

By Huimin Lu, Liyuan Zhao, Zhijiang Gao

The aluminum matrix composite reinforced by graphene was successfully fabricated using high pressure torsion (HPT). With only 0.5wt% graphene, the grain size was reduced to 100nm while that of pure Al was about 500nm. The hardness of the composite increased from the center (64HV) to the edge (120HV) of the sample. Moreover, the tensile strength of this composite reached 197MPa, while that of pure Al was 157MPa. The enhancement in mechanical properties was induced by grain refinement, load transfer from the matrix to the reinforcement and dislocations piled up at the grain boundaries.

Jan 1, 2015

By Minting Li, Hailong Yang, ChangWei, Cunxiong Li, Gang Fan, Xingbin Li, ZhiganDeng

The filtration problems on acid leaching sludge of high silicon zinc ore have been paid extensive attention in zinc hydrometallurgy. It was found that soluble silica can be effectively converted into silica precipitate with good settling, filtration and washing properties, and the filtration rate can be in excess of 800 L/m2 · h under certain leaching conditions. According to investigating on the filtration rate, viscosity and concentration of silica of leaching sludge or liquor, the filtering temperature can tremendously improve the filtration property of pulp. At the same time, the experimental data indicated that the viscosity of leaching liquor was the key factor influencing filtration property of leaching sludge.

Jan 1, 2016

By Z. W. Zhang, Songsong Xu, Jinhui Li, Yun Zou, Yu Zhao

High strength low alloy (HSLA) steels with high strength, high toughness, good corrosion resistance and weldability, can be widely used in shipbuilding, automobile, construction, bridging industry, etc. The microstructure evolution and mechanical properties can be influenced by thermomechanical processing. In this study, themomechanical processing is optimized to control the matrix microstructure and nano-scale precipitates in the matrix simultaneously. It is found that the low-temperature toughness and ductility of the steels are significantly the matrix microstructure during enhancing the strength by introducing the nano-scale precipitates. The effects of alloying elements on the microstructure evolution and nano-scale precipitation are also discussed.

Jan 1, 2016

By J. V. Happ

The investigation reported in this paper was prompted by the belief that vacuum processing of copper mattes could provide significant advancement to present-day copper smelting and converting technology. Specifically, vacuum distillation of copper mattes in a unit such as the R.H. vessel used in vacuum degassing of steel, can lead to improvements in: converter flue-gas-cleaning system, purity of acid (or liquid SO2), aisle hygiene, purity of electrorefined copper and smelter flexibility. In the study conducted, removal of Volatile impurities (arsenic, antimony, bismuth, lead and zinc) from liquid mattes, by vacuum distillation in a laboratory-scale equipment was performed. The conditions investigated covered a temperature range of 1123-1223K, absolute pressure of 6.5-0.5kPa (50 - 3 mm Hg) and with bleed gas consisting either of pure oxygen or argon. Six matte samples (four U.S. and two foreign) were tested. Under the "best" conditions arsenic and antimony were reduced to << 0.01% in the product matte. The removal of bismuth, lead and zinc was variable and appeared to be influenced by the matte composition of the sample. As might be expected, the rates of distillation of the various species were increased at higher temperatures and lower absolute pressures. The influence of a small flow rate of gas (02 or Ar) over the melt did not have a signifi¬cant influence on the extent of impurity removal. The magnetite content of the matte was reduced by up to 30% during vacuum treatment and was favored by a low partial pressure of oxygen over the melt. Substantial amounts of sulfur were also evaporated and an, overall increase in copper grade of the matte was realized. The paper concludes with an evaluation of industrial aspects of the process as applied to conventional smelters.

Jan 1, 1983

By Shi Guan-Yong, Niu Li-Ping, Dou Zhi-He

"In the preset work, the viscosity model (named modified KTH model) proposed by Sichen Du and S. Seetharaman et al and extended by Shu Qi-feng was applied to the ESR slag systems. A correlation to predict the viscosities of CaF 2-(CaO)-Al203 slags using interaction coefficients of different cations in the presence of oz-and viscosity interaction coefficients between oz-and F in the presence of different cations has been developed. The interaction coefficient between oz- and F- in the presence of Al3+ was determined from the experimental data as shown in known literatures. The good agreement between the calculated viscosities and the experimental data in the CaF2-(CaO)-Al203 systems has indicated that this approach can be successfully employed to predict the viscosities of ESR slags.IntroductionReliable viscosities data of high-temperature slag melts are important for the modeling and design of high temperature metallurgical processes. Although a number of experimental measurements have been carried out, the available viscosities data is still scarce compared to the needs of today's technology, especially in the case of complex melts. In process simulations, the needs of viscosity descriptions for complex systems which could enable the extrapolation of the data as functions of temperature and composition is strongly felt today."

Jan 1, 2013

By S. N. Monteiro, C. M. F. Vieira, M. M. Ribeiro

"This work has as its objective to evaluate the effect of incorporation of the powder waste retained in the eletrostatic precipitator of the sintering stage from an integrated steel making plant on the physical and mechanical properties of a red ceramic. Formulations were prepared with incorporation of the waste in amounts up to 20 wt.% into a kaolinitic clay. Rectangular specimens were prepared by uniaxial mold-press at 20 MPa and then fired at 750, 900 and 1050°C. The evaluated physical and mechanical properties were: linear shrinkage, water absorption and flexural rupture strength. The results showed that the waste has a potential to be used into red ceramics. The incorporation of the waste enhanced the properties of the ceramic, decreasing the water absorption and increasing the mechanical strength at all investigated temperatures.IntroductionThe sintering stage of an integrated steel-making plant is dedicated to the agglomeration of a mixture of iron ore, coke or coal, fluxes and water [1]. It is a common practice in this stage to use of solid wastes with great amounts of iron in the form of sludge and powder. One of the atmospheric pollutants generated during the sintering process is the particulate material, which is normally retained in an equipment denote as electrostatic precipitator. This equipment retains very small particulates, present in the gaseous emissions by application of an electrical potential difference in between the plates that the fluid is forced to go through. [2]."

Jan 1, 2011

By Alexander I. Raitchenko

"Although one takes into account only thermal expansion usually at analysis of convection onset, the essential factors include magnetic and electric fields. If Lorentz-force originating from intercrossed electric and magnetic fields' action is directed downwards its effect strengthens gravitational action, and value of critical Rayleigh number (limit value for convection onset) must decrease; increasing of critical Rayleigh number should be observed in case of Lorentz-force directed upwards. Extent of such an influence is determined by relation of Lorentz-force to hydrostatic head in gravitational field. Competition between electromagnetic force due to nonuniformity of electroconductivity (on account of its temperature dependence) and electromagnetic buoyancy force may have ambiguous effect: both increase or decrease of critical Rayleigh numbers. Proposed conception is applicable to analysis of situations in liquid conductors and conductive gases.IntroductionStatic or dynamic situations in fluid media are determined besides properties of these media by a variety of external influences. However one correlate~ the onset of the convection and its development with influences of the minimum quantity of external causes frequently. Most known and usual factors are the gravitational and temperature fields. The number of processes includes heat generation in media volume, and theoretical analysis in these cases takes into account this interior heating together with boundary temperature conditions. But explanation of many natural and technical events is not complete and cogent within limits of thermo-gravitational terms. The whole complex of acting factors which influence convective processes in techniques and nature is greater in many cases. In particular the action of · electromagnetic nature often has not less importance than gravitation one. Stability or instability of a current layer in the plasma must be determined by non-uniformity of electroconductivity owing to non-uniformity of temperature [1]. The presence of Joule dissipation in the plasma through which the electric current flows stipulates initiation of origin of overheated instability [2]. It is known that electroconductivity of arc in the boundary zone changes sharply with radial distance [3], and this must influence its stability essentially. If the intercrossed electric current and magnetic field begin to act on an electroconductive fluid besides the non-uniform temperature field and the gravity, the conditions for the onset of the convection change radi- . cally: both the temperature field and their solutions have to be changed also. The analysis of equilibrium single-time correlation functions of fluctuations must be employed for situations with enlarged number of factors as this was in case for the Rayleigh-Benard problem where the object is a horizontal layer of liquid. This can be carried out by taking into account the detached forces' correlations [ 4, 5]"

Jan 1, 1999

By Ivo André

Sorption of copper ions from aqueous solutions by dried biomass of the aquatic plant Potamogeton luscens was studied at laboratory scale. The aquatic plant was collected in water resources in Brazil, washed, dried at 60°C and ground in a bladed mixer. Sorption experiments were conducted in agitated flasks and in a packed bed column. Maximum copper removal was obtained between pH 5.0 and 6.6 when copper was present in the ionic form Cu&apos;. Sorption followed the Langmuir isotherm with saturation attained at 35 mg/g. Free energy of sorption was found, to be of the order of -25 kJ/mol. Sorption kinetics data were better described by a second order reaction and rate constants were calculated in 0.030 1/(min.mg) for - 4.0 mm particles and 0.081 1/(min.mg) for - 0.59 mm particles. Removal of metal ions in a packed bed column showed that Potamogeton luscens biomass can be used in several sorption/dessorption cycles. After sorbent saturation, copper ions can be recovered from the loaded biomass by elution-with H2SO4, solution. Main mechanism responsible for heavy metal uptake was found to be ion exchange. Results are discussed in terms of the surface properties of the biomaterial, solution chemistry of copper ions and thermodynamics parameters.

Jan 1, 1995

By Isabela Leao Amaral da Silva, Felipe Perisse Duarte Lopes, Alice Barreto Bevitori, Sergio Neves Monteiro, Ruben Sanchez Rodriguez

"The fibers extracted from the stem of the ramie plant are among the strongest natural lignocellulosic fibers with a potential to be used as reinforcement of polymer matrix composites. Characterization of the ramie fiber has recently been conducted for its physical and mechanical properties. However, the effect of increasing temperature on the ramie fiber behavior has not yet been fully investigated. Therefore, the objective of this work was to perform a thermal analysis on ramie fibers with different diameters within the naturally found range of practical interest. The analysis was conducted by thermo-gravimetric, TGA and DTG, as well as differential scanning calorimetric, DSC, techniques. It was found that the ramie fibers present thermal stability up to 200°C and then suffer a sharp deterioration between 300 and 500°C, resulting in characteristic peaks.IntroductionSince the middle of last century, polymer composites have substituted many conventional monolithic materials in applications ranging from aerospace to sport [l]. The main advantages of these composites are the low density and flexible properties specially using fiber as reinforcement to suit the mechanical performance requirements [2]. These are usually high strength and stiffness requirements that could be reached with synthetic fibers such as glass, carbon and aramid fibers. In recent years, however, the use of synthetic fibers is being questioned in terms of problems caused to the environment. In fact, as non degradable material, synthetic fibers are associated with long term pollution when discarded. Moreover, the expended energy for fabrication and processing can be related to relatively large amounts of C02 emissions and represents a contribution to global warming [3]. Glass fiber, in addition, is toxic and cannot be incinerated as a waste in thermal power plants [ 4]. Possible substitutes for glass fiber are the natural fibers. Many natural fibers are today being considered as viable alternatives to replace glass fiber as reinforcement of polymer composites. In particular, some natural lignocellulosic fiber extracted from plants present a real potential for this replacement [2-8]. Their comparative advantages are lower density and reduced cost as well as renewability, biodegradability, recyclability and neutrality with respect to C02 emission [3]."

Jan 1, 2011

By Larry G. Twidwell, Jannette L. Chorney, Bryce D. Ruffier, Katelyn M. Lyons, Daniel W. Gaede, Ryan J. Foy, Jerome P. Downey

The Metallurgical and Materials Engineering Department at Montana Tech is investigating various methods of extracting and refining rare earth elements from mineral ores and concentrates. As part of this research, an elevated temperature “roasting” process has been evaluated as a means of converting the rare earth elements contained in various matrices to bromides as a pretreatment step in preparation for downstream rare earth element extraction and recovery operations. Laboratory and bench-scale experiments have been performed to assess the effects of varying temperature (150 to 400° C), time (1 to 4 h), and the ammonium bromide to rare earth oxide molar ratio (6 to 24) in the roaster charge. The results show that nearly complete bromination of the rare earth oxide is achievable when the roast is performed under optimum conditions.

Jan 1, 2015