Search Documents

Microfluidic Solvent Extraction for Mineral Processing of Copper Leach Solutions

Sep 13, 2010

By E. P. Klier, S. M. Grymko

The transformations in eutectoidal systems have been extensively studied as they occur in steels.&apos; As a consequence of these studies the martensite, bainite and pearlite reactions found for most steels are widely recognized. Further, because of the work of Smith and Lindlief2 and of Greninger and Troiano3 these reactions, except for the bainite reaction, are considered as typical for all eutectoidal systems. The primary alloy studied by Smith and Lindlief2 was a CuAl alloy of near eutectoid composition as was the alloy more recently studied by Mack.4 The transformations in these alloys were, for the most part, studied metallo-graphically, while an X ray analysis of structures was essentially wanting. It has appeared desirable, therefore, to investigate selected CuAl alloys at and slightly away from eutectoid composition. For this purpose three alloys were prepared containing 10.5,11.9 and 13.5 pct A1 respectively. The results of a metallographic and X ray analysis of structures obtained for isothermal transformation of the ß-phase are reported here for the 11.9 and 13.5 pct A1 alloys. Introduction The phase equilibria in the CuAl alloys of immediate concern are indicated in the equilibrium diagram section presented in Fig 1.5 The equilibrium and transition structures which have been reported in this system are as follows: a = copper rich terminal phase (f.c.c.) ß = high temperature eutectoidal phase (b.c.c.) r2 = aluminum-rich intermediate phase (r-brass structure) a&apos; = modified a-phase postulated by Bollenrath and Bungnrdt.26 ß1 = ordered ß (b.c.c.) ß&apos; = martensite structure: A1 < 13 pct (near h.c.p.) ß" = ß&apos; of Smith and Lindlief2 7&apos; = martensite structure: A1 > 13.5 pct (h.c.p.); ß2 of Bollenrath and Bungardt.26 The eutectoid transformation can be suppressed at sufficiently high cooling velocities. The ß-phase is then retained to about 500°C where ordering sets in. The ordering interval is not satisfactorily known but indirectly appears to be non-suppressible. Subsequent to the ordering reaction and consequently at lower temperatures, the ordered ß1 decomposes to a marten-sitic structure. The kinetics of these reactions and in particular those of the martensite reaction have an important bearing on the results obtained in this investigation. Since some confusion exists concerning certain reported aspects of these reactions, they will be considered in some detail. THE MARTENSITE REACTION The martensitic structure is formed on cooling through a critical range6

Jan 1, 1950

By Drew Martin

In March 2010 the Boral Linwood Quarry, Adelaide South Australia, implemented the blasting contractors Monte Carlo Blast Vibration Model as part of their blast design process. The Linwood Quarry was developing an area where blasting activities were marginally complying with the statutory vibration limits. Compliance to the statutory limits was only being achieved through the use of small blasts (less than 15 000 T (14 763 ton)) at a high cost to the quarry.

Jan 1, 2012

By A. G. Yapo, T. W. Camm

"All-in sustaining cost is a metric used by mining companies to reflect the cost of gold mining in a consistent format useful to both investors and mining professionals. Cost reporting focused on the direct cost of mining and processing ore was summarized in the non-GAAP cash cost developed by the Gold Institute in 1996. In 2013, a group of mining companies, working with the World Gold Council, developed a more inclusive approach to reporting costs designed to solve the dilemma of showing a more comprehensive reflection of recurring costs involved in producing gold, without discouraging investors. INTRODUCTION Mining today plays a key role in the development of our civilization as a source of essential raw material and provider of essential fuels, producer of jobs, and a factor in support of the international balance of monetary payment (Camm, 2014). Professionals in mining locate, develop, design and manage ore deposits in an environmentally safe and profitable manner. As mineral deposits become increasingly scarce, new challenges face the industry. A current trend is to an increased emphasis on underground mining techniques for deeper deposits. Operations are safer today than before as companies understand better their work environment and the importance of mining responsibly. A continual challenge for the industry is accurately reflecting the costs and selling price of ore. An enduring characteristic of mining is the situation where the market typically determines the price of a commodity; the main control a company has on the bottom line is to control the cost of production. An attempt to bring light and clarity on the cost of their business will give a better idea to investors on the true profitability of the mining business. Gold producers face this struggle to accurately reflect the cost of production while also seeking to attract the interest of the investment community (Hill, 2013). In order to have a consistent format to report on their production costs, leading gold producers through their alliance inside the World Gold Council (WGC), worked on the adoption of a new cost framework: the All-in Sustaining Cost (AISC) and All-in Cost (AIC). Since 1996, the traditional cash cost reporting has focused only on the mining and processing costs incurred in mining an ounce of gold, which included the costs of goods sold (labor, energy, and consumables costs) and royalties (Table 1). But cash cost reporting ignores many important aspects, like sustaining capital, general and administrative expenses, and site rehabilitation at the end of the mine life (Whelan, 2013). The cash cost was used to attract many investors into the business. In fact the high gross margin (sales minus cash costs) has been promoted the past decades by the industry instead of the net or operating margin. As a result, even when the gold price was high, nearly $1900 per ounce in August 2011, gold producers were not reporting excessive profits in their cash flow / income statements, to the disappointment and incomprehension of investors (Milstead, 2014). The truth was simply that the other costs omitted in the traditional cash cost were reducing the apparent profits."

Jan 1, 2017

By D FitzGerald, S Jakica, R Paterson, J Silic

A new 2.5D airborne electromagnetic (AEM) algorithm has been developed by Intrepid Geophysics and Jovan Silic &amp; Associates. The advantage of 2.5D (2D geology, 3D source) AEM inversion in 3D geological mapping applications and identification of conductive drilling targets, compared to the more commonly used conductivity-depth imaging (CDI) transforms or 1D inversions, are demonstrated using examples from banded iron formations (BIFs) and other geological settings. We show emerging AEM systems are capable of providing estimates of economic rock unit thicknesses, dips and fault definition at an accuracy that mitigates the need for pattern drilling.The 2.5D inversion application used in this work and described in Silic et al (2015) is a substantially changed version of ArjunAir (Wilson, Raiche and Sugeng, 2006), a product of CSIRO/AMIRA project P223F. The changes include a new forward model algorithm and a new inversion solver. The application enables the accurate simulation of 3D source excitation for full domain models inclusive of topography, non-conforming boundaries and very high resistivity contrasts. Solution is accurate for a geoelectrical cross-section, which is relatively constant along a strike length that exceeds the AEM system footprint.The major innovation includes a new inversion solver with adaptive regularisation, which allows the incorporation of a misfit to the reference model and the model smoothness function.Memory usage has been dramatically reduced and is estimated prior to execution. For speed the software has been parallelised using Intel message passing interface (MPI) and can be used on standard computing hardware or computing clusters. Data from survey lines with lengths exceeding 100 km can be inverted on high end laptop computers.We allow flexibility in the selection of components and in the estimation of noise.AEM inversion examples are shown for surveys from BIFs, base metals (volcanogenic massive sulfides) and geological mapping projects and the results are compared with known geology and drilling. We demonstrate the much improved mapping and target definition delivered by this inversion method when compared with the other more common transforms or inversion methods used on these projects.CITATION:Paterson, R, Silic, J, FitzGerald, D and Jakica, S, 2017. High accuracy .D airborne electromagnetic inversion method for banded iron formation and other geological settings, in Proceedings Iron Ore 2017, pp 319–330 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By A J. H Newell

The background and the basis for conducting a Technical Due Diligence are discussed as well as the source information, typical studies and potential limitations. Typical short comings including ‘show-stoppers’ are presented for the metallurgical area, with examples. Issues found in other areas such as geology, mining, infrastructure and financial evaluations are briefly reviewed, highlighting the input and interaction required by metallurgists with these disciplines. A checklist is provided as a guide to maximise the success of a Due Diligence as well as a check on the quality of a Feasibility Study.CITATION:Newell, A J H, 2015. Fatal flaws in technical due diligences, in Proceedings MetPlant 2015, pp 61–77 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By H. Tudeshki, A. Tayebi

"The large extent of global production and consumption of aggregates from quarries, grabs one´s attention and makes its substantial and essential standpoint in the world today pretty clear. A great amount of aggregates is utilized in civil engineering applications such as road construction, railway industry, concrete production, etc. Considering this fact that igneous rocks display a higher strength and abrasion resistance, this type of rock is preferred in the field of civil engineering. For all these applications, rock quality assurance is a key factor and certainly unavoidable, and it has great influence on the quality of constructions in civil engineering. One of the major problems encountered by both the producers and users of igneous rock is the fact that, with the passage of time, some specific rocks lose their strength, up to a complete loss of structure or in other words, their disintegration and degradation. In the last decades, different methods and procedures such as Glycol test, methylene blue dye test, as well as the Los Angeles test have been introduced to distinguish these rock properties, and to identify these problems. However, as these methods are time consuming, hard to perform, only to be applied to hand-piece samples, requiring special laboratory equipments, and only possible to be accomplished under laboratory conditions, their application has always been limited to some specific cases, and they are neither recommendable nor advantageous. In addition, these methods provide partially different results for the same rock. To address this widespread quality management problem of the quarry industry, a relatively quick, easy and user-friendly approach is necessary. It calls for a systematic solution with a device that can simply be used day to day in a mine for quality control of the quarry´s daily production. This scientific research is concentrated on developing a systematic method for early recognition and diagnosis of rock quality, in order to control and manage the quality of the quarry production in advance. This method was developed, based on the procedure of the magnetic susceptibility measurement. The obtained values can lead to valuable information regarding the quality of the rock and allows the quality control process to be accomplished and performed at the borehole location. This approach has been assessed through extensive field and laboratory studies. A detailed and comprehensive discussion will be made on the results of the experiments. The advantages and impacts of the application of this method, on increasing the reserves and environmental protection are also discussed."

Jan 1, 2011

By T King

This paper reviews the changes in the coal industry over the past 30 years and attempts to predict the trends over the next ten years. The last 30 years have seen a steady concentration of production into fewer, larger mines, which operate on 3: more continuous basis, and a major increase in productivity per employee. Coal exports have increased from zero to almost half the country&apos;s total production. As well as major changes in exploration and mining equipment and the increasing use of computer tools, the industry now operates in a relatively new regulatory and commercial environment. &nbsp; Safety legislation now requires the writing and enforcement of policies and procedures by the mining companies, rather than adherence to inflexible regulations enforced by an Inspector. Accident rates have decreased dramatically. The transition from coal mining licences to permits, requiring landowner consent and resource consents, is well under way. Environmental controls are now an essential aspect of the industry. &nbsp; Equipment suppliers now offer maintenance services, production guarantees and flexible financing. &nbsp;Contract miners offer mine design and restoration as part of the contract. In a similar approach, Solid Energy now offer an ash disposal service and assistance with resource consents to their customers as well as investment in technology to ensure a consistent product to demanding specifications. Solid Energy has proposals for energy centres which install and operate the coal burning appliances and simply sell energy to the customers. The next 10 years should see an intensification of these trends of bigger mines, more exports and greater technology and a &apos;package&apos; approach to customer service.

Jan 1, 1997

By Graeme Lamson, Rene Dobbe, Merle Kalstrom, Janice Baron, Robert Thorpe, Chris Martin, Snezana Bajic, Amanda Palko

"This paper presents early results from a case study at the Mount Polley porphyry copper mine in British Columbia, Canada. Daily mineralogical data was acquired and reconciled with daily plant assay and recovery balances to interrogate the mineralogical controls on plant performance. After commissioning, the Minesite machine operated smoothly and reliably, creating daily data to generate mineralogical balances around the circuit for a period of several weeks. The key data, on final products were produced within 13 hours of the end of the respective operating period. The resulting information allowed for a greater understanding of the opportunities and limitations of the Mount Polley metallurgy. In this paper, how this information can be used to help long term strategic planning for the operation, as well as mine planning and production forecasting and the fine tuning of day to day mill operations is described. Early data available at the time of preparing this paper indicated that roughly 40% of the sulphide losses, or 32% of total copper losses existed as low grade inclusions in +75 micron tails. This represented the dominant form of long term copper losses, demonstrated repeatedly in the routine analytical data. However, on a day-to-day basis, the amount of copper present as chrysocolla is the major driver behind variations in total copper recovery. The degree to which this influences mill recovery is valuable to the geologist or mine planner. As they are armed with mineral speciation information for future ores, this will allow for improved mine planning, prediction of copper recoveries and production forecasting. The data was also started to find value in the mill by showing what caused sulphide losses. In the roughers, for example, the data showed poor recovery was the result of poor flotation performance and not any changes the speciation of copper sulphides or their liberation characteristics."

Jan 1, 2014

By Alphonso Cornejo, Galen H. Clevenger

This bibliography was compiled in connection with an investigation of the Caron process for the treatment of manganese - silver ores , conducted by the T. S. Bureau of Mines in cooperation with the Netherlands East Indies Government . The object of this investigation was to develop a practicable method for treating the refractory manganese- silver ores found in these two countries . The results of the work will be published as a bulletin of the Bureau of Mines . This bibliography summarizes the available information on the subject previous to the investigative work embodied in the forthcoming bulletin, and may be useful to those metallurgists or others conducting work along this line .

Mar 1, 1923

By W. M. Jansen

In many mineral processing operations, the reported production figures for an accounting period may not make the best use of available data. While most of the mathematical approaches, such as check-in/check-out, mass balancing, used in effective metallurgical accounting strategies are well understood, the sources and magnitude of measurement errors generally are not. As part of the &apos;AMIRA P754-Metal Accounting and Reconciliation&apos; project, a study was undertaken at the Northparkes copper/gold concentrator near Parkes, New South Wales to examine the data used in their concentrator metallurgical accounting system. This paper summarises the results of a detailed examination of the mass measurement systems around the concentrator as well as the primary sampling system used for grade estimation. The goal of this work was to develop practical techniques to quantify the error (ie both accuracy and precision) of the measured metal accounting information. With this information, statistical confidence levels for this data can then be calculated. If the errors are small, the effect of error in each piece of measured data can then be propagated to other calculated production figures such as recovery and feed grade using a statistical technique called `the propagation of error&apos;.

Jan 1, 2007

By Rao Balusu, Bharath Belle, Krishna Tanguturi

A collaborative research project is undertaken by Anglo American Coal and CSIRO to develop appropriate strategies for gas and spontaneous combustion management of longer panels. Extensive computational fluid dynamics (CFD) modelling studies have been conducted and calibrated using operational longwall goaf gas data to obtain a fundamental understanding of goaf gas flow patterns in longwall panels of 1.0-km and 3.0-km lengths and a detailed investigation of the effect of various mining and operational parameters on goaf gas flow patterns. The modelling studies have also been used to investigate the performance of various gas drainage and proactive inertisation strategies during various stages of longwall panel extraction. Simulation results indicated that apart from tailgate (TG) side goaf holes, gas drainage from maingate (MG) goaf holes and the mid panel start-up goaf holes would be useful for flat seam field conditions. Operation of 8–10 goaf holes is recommended for field site conditions with high goaf gas emissions of 6000 L/s. The modelling results indicated that the traditional inert gas flow rate of 500 L/s currently used in some mines would be insufficient to achieve effective goaf inertisation in long panels. Results indicate that 3.0- km-long panels would require 1500 L/s of inert gas and there is a need for multi-point inert gas injection strategy for effective goaf inertisation. In this paper, details and results of modelling investigations and recommended strategies for gas and spontaneous combustion management in 1.0-km- and 3.0-km-long panels are presented.

By Rao Balusu, Bharath Belle, Krishna Tanguturi

A collaborative research project is undertaken by Anglo American Coal and CSIRO to develop appropriate strategies for gas and spontaneous combustion management of longer panels. Extensive computational fluid dynamics (CFD) modelling studies have been conducted and calibrated using operational longwall goaf gas data to obtain a fundamental understanding of goaf gas flow patterns in longwall panels of 1.0-km and 3.0-km lengths and a detailed investigation of the effect of various mining and operational parameters on goaf gas flow patterns. The modelling studies have also been used to investigate the performance of various gas drainage and proactive inertisation strategies during various stages of longwall panel extraction. Simulation results indicated that apart from tailgate (TG) side goaf holes, gas drainage from maingate (MG) goaf holes and the mid panel start-up goaf holes would be useful for flat seam field conditions. Operation of 8–10 goaf holes is recommended for field site conditions with high goaf gas emissions of 6000 L/s. The modelling results indicated that the traditional inert gas flow rate of 500 L/s currently used in some mines would be insufficient to achieve effective goaf inertisation in long panels. Results indicate that 3.0- km-long panels would require 1500 L/s of inert gas and there is a need for multi-point inert gas injection strategy for effective goaf inertisation. In this paper, details and results of modelling investigations and recommended strategies for gas and spontaneous combustion management in 1.0-km- and 3.0-km-long panels are presented.

By Stewart R. D, Lawrence W, Youl M. J

The trend towards contracting by major coal mining companies such as BHP Coal and MIM Ltd is examined. Reasons why this trend is occurring are discussed and the concept of partnering is examined. Two case studies are given: the Mt Owen Mine in the Hunter Valley, NSW and the South Walker Creek Mine in the Bowen Basin, Queensland.

Jan 1, 1997

By James A. Finch, Xiang Zhou, Yue Hua Tan

Methods to determine frother functions, control of bubble size and froth properties, are now widely used. Some collectors also exhibit frother functions which are less understood. Using a water-air system in a mini-mechanical flotation cell setup, this paper determines bubble size and water overflow rate for three amine collectors: one primary amine (dodecylamine, DDA) and two commercial ether amines (Flotigam® EDA and Flotigam® 2835-2L) and their combination with two common frothers, MIBC (methyl isobutyl carbinol) and PPG 425 (polypropylene glycol, molecule weight 425). Compared to the frothers, the amines were less effective in reducing bubble size, giving larger minimum size and the two commercial amines showed evidence of coalescence at low concentration. In blends, at fixed frother dosage, frother eliminated the coalescence but as amine concentration increased the amines dominated bubble size. Water overflow was a strong function of reagent type. For fixed 1-cm froth depth, PPG 425, Flotigam® 2835-2L and to a lesser extent DDA produced overflow while MIBC and Flotigam® EDA did not. In blends with frother overflow increased except with Flotigam® EDA. Mechanisms are briefly explored. The principal benefit of blending identified is the elimination of coalescence if residual concentration of the two commercial amines is below ca. 10 ppm.

By M. Gous

Keywords: Pyrometallurgy, Namakwa Sands, ilmenite, DC arc furnace, titania slag, pig iron Namakwa Sands is a heavy minerals mining and beneficiation business in the Anglo Base Metals Division, and operates along the West Coast of South Africa. The business encompasses mining, mineral concentration, separation, and smelting operations. The smelting process comprises the carbonaceous reduction of ilmenite to produce titania slag with a TiO2 content of 86%, and iron with a carbon content of 2.5%. The Namakwa Sands smelter, situated near the Saldanha Bay harbour, commenced smelting operations in 1994, when a 25 MW DC arc furnace was commissioned. The smelting operations were expanded in 1999, with the commissioning of a second 35 MW DC arc furnace. Despite the fact that ilmenite smelting poses a technical challenge in terms of the high temperatures required, the physical characteristics of the slag, the constraints placed on the feedstock, and the tight product specifications, Namakwa Sands has continually increased slag production since 1995. High furnace feed-on utilisation and furnace stability, complemented by continuous improvement drives, will be the vehicle to drive performance in the short term, with longer-term performance enhancements due to strategic process development.

Jan 1, 2006

Jan 1, 2000

By Patrick J. Doig

The contract for the construction of the Inline Pump Station for the Milwaukee Metropolitan Sewerage District involves the sinking of three shafts and the excavation of a pump chamber. The shafts are being sunk to a depth of 104 meters and pass through 52m of sediments before encountering dolomitic bedrock. The pump chamber is constructed in dolomite. The sediments are alluvial, estuarine and lacustrine in origin, with some ice margin deposits. They comprise loosely consolidated fine to coarse grained sand, silts, clays and gravels, and they are heavily saturated with a water content often above 60%. The water table is at a depth of 3m. The dolomite is silurian, generally dense, with some clay-filled vugs and shale partings. Until 1983, underground construction in the Milwaukee area had been limited to depths of 26m in the sediments and 20m in the dolomites. Water control methods had included caissons, compressed air, extensive internal and external dewatering, and grouting. Flows of 20 liters per second were commonplace with as much as 80 liters per second being encountered in the rock. However, in 1984 work was commenced on the deep sections of the Milwaukee sewerage scheme with the letting of three major contracts including the Inline Pump Station. With excavation taking place at greater depths, it become obvious that previous methods of water control would be inappropriate. To protect against major inrushes of high pressure water in the rock, an extensive program of pre-grouting from the surface was specified. Water control in the sediments was left to the discretion of the contractor and in each case freezing was choosen. This paper describes in detail the grouting and freezing procedures.

Jan 1, 1985

An evaluation of blasting procedures in surface mining operations was undertaken to determine means for improving safety. The objectives of the study were to: 1. Develop guidelines for safer blasting practices 2. Specify changes or additions in regulations concerning the use of explosives 3. Identify areas in which additional knowledge needs to be developed. As a basis for the evaluation, an idealized blasting cycle was prepared. Developed in the form of a scenario of surface mining operations, this synthesis of good mining practices served as the standard against which observed activities were compared. Blasting hazards were divided into two categories: those known to exist and those which are potential. Known hazards were identified in terms of situations which have actually resulted in explosives-related accidents. The evidence for known hazards was obtained primarily from MESA records of mine accidents. Potential hazards were identified by observation of mining activities and consultations with mining, explosive industry and government regulatory agency personnel.

Jan 1, 1977

As metal prices fluctuated over the years, so too have the fortunes of many of those mining in Canada?s Yukon province. With a rich mining history that dates back to the Klondike gold rush of 1896 to 1898 and continues to thrive today, Yukon has experienced several ?boom-and-bust? cycles. However, during the world?s most recent mining ?bust? Yukon has held strong and has re-mained one of the world?s hottest destinations for mineral exploration. In fact, the area even exceeded forecasts in 2009, more than doubling last year. And the near-future looks just as bright.

Jan 1, 2010