Search Documents

Stope back conditions in the cut-and-fill stopes at New Broken Hill Consolidated Limited often deteriorate to such an extent that, because conventional rockbolts are not able to maintain safe working conditions, square-set timber is installed. An attempt to eliminate this costly procedure has involved the use of long grouted rockbolts using high tensile prestressing wire. These bolts were developed in conjunction with the prestressing engineers of BBR (Aust.). This form of support has improved the back conditions, maintained safe working conditions, and delayed the introduction of timber in a number of stopes.Production from these stopes has been maintained at its previous level (at a rate approximately double that of a comparable timber stope).

Jan 1, 1974

By D. S. van Vuuren

Over the last 60 years many different processes were conceived to reduce the cost of titanium produced by the Kroll process. However, success eluded all previous efforts, which were consequently terminated in periods of economic downturn. Recently, the grow thin demand for titanium and the high cost of producing the metal again sparked renewed attempts in various parts of the world to replace the antiquated Kroll process with a more efficient route. The different options to produce titanium are reviewed, classified and evaluated in terms of the fundamentals underlying the technologies, and it is shown that the options considered to be the most likely to replace the Kroll process, are continuous processes to reduce TiCl4 metallo-thermically to titanium powder. Of these, continuous magnesio-thermic reduction of TiCl4 would conceptually result in the lowest-cost and highest-value product. However, when considering by-product salt removal from the titanium product and recycling of the salt as well, sodio-thermic reduction of TiCl4 is better.

Jan 1, 2009

By Firth B. A

The flotation of fine coal (minus 0.5 mm) often requires the addition of an insoluble hydrocarbon collector to apparently promote the adhesion of coal particles to air bubbles. A series of experiments was conducted using a radiotracer and narrow size fractions of clean coal to determine the effect of particle size distribution, collector addition rate, desliming of feed and emuIisification of collector on the distribution of collector between the different size fractions. The concentration of collector per gram of each size fraction was found to be approximately proportional to (average particle size)-2 except if the collector was emulsified prior to addition, the dependence altered to approximately (average particle size)-1. Mechanistic consequences are discussed.

Jan 1, 1982

By Mark P. Juzli

During the 1980s, a revolution has been taking place in industrial minerals marketing. Transportation deregulation and a handful of creative marketing and distribution managers have completely changed the rules for marketing many industrial minerals. Minerals are being transported much farther than in prior decades and at much less cost. Bulk and package terminals are becoming increasingly common as a means to take advantage of freight rate savings and to provide enhanced service to faraway customers. Water and rail transportation are being used increasingly to penetrate markets considered unreachable just a few years ago. No longer do the textbook rules of thumb for industrial minerals marketing apply. This author recalls three of those rules he was taught in mineral economics graduate school in the 1970s. As recorded in class notes: • construction aggregates are seldom shipped more than 32 km (20 miles) from the quarry; • cement is sold within 240 km (150 miles) of the mill; and • industrial sand is sold regionally - it is freight constrained to a market radius of no more than 320 to 400 km (200 to 250 miles) from the plant. And yet, the author looks up in 1989 and observes overland movements of aggregates of many hundred miles, overland movements of cement and industrial sand of 1600 km (1000 miles) or more, and water movements of both aggregates and cement into the United States from sources halfway around the world. Truly, industrial minerals are in the midst of a marketing revolution. The companies that have led this revolution have enjoyed considerable financial success in the 1980s. They have enhanced their profitability by increasing market share, capacity utilization, and average selling prices by taking product to remote markets where premium prices are available. They have consistently outperformed their competition, many of whom remain unaware that the marketing revolution going on around them is actually a transportation/distribution revolution. The successful industrial minerals company of the next 10 to 15 years must participate in the transportation revolution as it continues to evolve. Additional human and capital resources must be committed to maximize the effectiveness of a company's transportation and

Jan 1, 1989

By Chris D. Winkler

Vanadium-based sulphuric acid catalyst has been utilized to oxidize SO2 to SO3 since the early 1900?s. This versatile product displaced the expensive and easily-poisoned platinum-based catalyst in nearly all applications by the 1930?s. MECS has been manufacturing the vanadium-based catalyst since 1925 and today is the leading supplier in the world of sulphuric acid catalysts in a variety of forms. Currently, MECS has world-wide customer/technical support for the catalyst as well as a dedicated catalyst manufacturing plant in Martinez, California. MECS also has a strong technical and research and development program dedicated to creating new and improved products and services. This paper will describe some of the technical details of vanadium-based sulphuric acid catalysts as well as offering a unique look into how caesium-promoted MECS catalysts can be used in single and double absorption acid plants, and off-gas plants running on irregular gas feeds, to reduce emissions and pre-heater run times. An update on MECS technical services extended for use in characterizing converter performance is also presented.

Jan 1, 2009

By Chris D. Winkler

Vanadium-based sulphuric acid catalyst has been utilized to oxidize SO2 to SO3 since the early 1900?s. This versatile product displaced the expensive and easily-poisoned platinum-based catalyst in nearly all applications by the 1930?s. MECS has been manufacturing the vanadium-based catalyst since 1925 and today is the leading supplier in the world of sulphuric acid catalysts in a variety of forms. Currently, MECS has world-wide customer/technical support for the catalyst as well as a dedicated catalyst manufacturing plant in Martinez, California. MECS also has a strong technical and research and development program dedicated to creating new and improved products and services. This paper will describe some of the technical details of vanadium-based sulphuric acid catalysts as well as offering a unique look into how caesium-promoted MECS catalysts can be used in single and double absorption acid plants, and off-gas plants running on irregular gas feeds, to reduce emissions and pre-heater run times. An update on MECS technical services extended for use in characterizing converter performance is also presented.

Jan 1, 2009

By E. L. McHugh, J. M. Girard

This paper discusses the results of two recent case studies in which high-tech prototype instruments were used. The first case study describes the results of a ground-based hyperspectral imaging tool used to map the geology of an open-pit mine highwall. The second case study outlines the use of interferometric synthetic aperture radar and how this type of radar can be used in a variety of geotechnical situations. These case studies are part of an on-going research project at the National Institute for Occupational Safety and Health’s (NIOSH) Spokane Research Laboratory. The project objective is to implement engineering controls and design methods in order to reduce the number of injuries and fatalities associated with slope failures at mining operations. Project personnel are hopeful that these new developments in technology will lead to better geotechnical monitoring and design in slope stability and other important areas of rock mechanics.

By Jos. R. Guiteras

This is one of a series of information circulars describing mining and milling methods being published by the Bureau of Mines. The Summitville Consolidated Mines, Inc., is the only company now active at Summitville. Since the holdings of the company include those of most of the former producers of the camp, the paper virtually becomes a description of the Summitville district. The field data were collected from August 23 to 28, 1937. ACKNOWLEDGMENTS The writer gratefully acknowledges his indebtedness to H. F. Detrick, president, and Edward Thornton, general manager of the company for their cooperation in making this paper possible. Most of the information on underground operations was given by Roy Jellison, mine superintendent; the metallurgical data were supplied by Art Carl son, metallurgist, and W. L. Anderson, mill superintendent; much general and technical information was supplied by J. H. Hannan, engineer.

Jan 1, 1938

By L. M. Gould

"Syncrude Canada operates the largest oil sands crude oil production facility in the world and produces over 13% of Canada’s total oil requirements. To achieve this, Syncrude mines the oil sands in open pits, extracts the raw oil known as bitumen from the sand using water-based processes and upgrades it into sweet light crude oil by fluid coking, hydroprocessing, hydrotreating and reblending. The final product, Syncrude Sweet Blend (SSB), is sent by pipeline to three Edmonton area refineries and then to pipeline terminals which ship the SSB to refineries in Canada and the United States.As parts of the Mildred Lake base mine reached their economic life, they were replaced with new facilities at the Aurora Satellite mine. Aurora is situated on Oilsand Leases 10, 12 and 34, 35 km northeast of the Mildred Lake facility (Fig. 1).In 2000, the first hydrotransport low-energy extraction production train started up at Aurora. A second production train is scheduled for start-up in 2003. Open pit mining at Aurora occurs using two hydraulic shovels, two cable shovels, and trucks ranging from 320-ton to 380-ton payload capacities (Fig. 2).Once the oil sands is excavated, the trucks dump the ore into a crusher designed to break up the big lumps of oil sands and rock at peak rates of 11 000 t/hr. The ore is then transferred by conveyor to a surge pile and then to a mixing box which combines the oil sands with hot water. Following bitumen separation in the primary separation vessel, froth is delivered to Mildred Lake for processing via the intersite pipeline (Fig. 3).The goal of this paper is to illustrate how high precision shovel GPS (HPGPS) is being used at the Aurora mine to aid in mine planning. This can be accomplished by first describing the function of the mine planning department, describing the Aurora orebody, and finally explaining how the HPGPS system functions and how it is employed at Aurora.The short range mine planning department ensures a steady supply of ore is delivered to the plant at the desired grade in a sequenced and economical manner. This is done by creating a mine plan that consists of shovel dig locations that require the shovels to mine in a specified area at a specified elevation."

Jan 1, 2002

By Herty, C. H.

Three distinct processes take place during the conversion of iron ore to steel. First: the raw ore is reduced to metallic iron in the blast furnace and during this reduction certain constituents are dissolved in the iron, either through the solution of a solid into a liquid phase, as in the case of carbon, or by reduction of an oxide existing in the slag to the metallic element of that oxide, with subsequent solution of the metallic element in the iron. Thus by the process of solution and reduction, a pig iron results which contains about 4 per cent carbon, 1 per cent silicon, 1 to 2 per cent manganese, 0.1 to 0.4 per cent phosphorus, and 0.03 to 0.10 per cent sulfur. To obtain a sufficient yield of iron from the ore it is necessary that the reducing process be carried as far as possible, with the result that the impurities mentioned accompany the reduced iron. Second: to convert this iron into steel it is necessary to oxidize a part of the iron in eliminating the impurities to the extent desired for the particular product being made. In eliminating these impurities by oxidation a certain amount of iron oxide (FeO) dissolves in the steel. This dissolved FeO reacts with the metalloids, except sulfur, and to eliminate them to the desired extent it is necessary to leave a considerable amount of FeO in the metal. The reaction of iron oxide with silicon, manganese, and phosphorus results in the formation of the oxides of these elements. The oxides enter the slag and the extent of elimination of the elements depends on certain equilibria between the slag and the metal. The reaction of FeO with carbon results in the formation of the gases CO and CO, which, after saturating the metal, pass into the furnace gases. Third: after the iron has been purified to the desired extent as far as the elements listed are concerned, it is necessary to deoxidize the bath to remove the FeO, which is the vital factor in gas formation as the steel solidifies.

Jan 1, 1957

By Bhaskar B. Thapa

The proposed Caldecott fourth bore will consist of a two lane highway tunnel along California State Route 24 near the City of Oakland. The proposed design and construction sequence for the 15-m-diameter tunnel are based on the New Austrian Tunneling Method (NATM). The initial support system incorporates combinations of shotcrete, rock dowels, lattice girders, spiles, and grouted steel pipe canopies. The final lining is cast-in-place reinforced concrete. A waterproofing membrane and drainage system are placed between the initial and final linings. State Route 24 is a lifeline route, required to be open to emergency vehicles within 72 hours after a major earthquake, defined as having a return period of 1,500 years and a peak ground acceleration of 1.2 g. Although the seismic design criteria are stringent, the design of the tunnel lining system is ultimately controlled by static ground loads in the weak rock along the alignment.

Jan 1, 2008

By R G. Barker

The NZ Minerals Industry Association has continued to advance the interests of the minerals sector through leading the establishment of a Minerals Industry Advisory Committee, and the preparation of a technology strategy with funding assistance from the Foundation for Research, Science and Technology. The current moves mirror those of more than 30 years ago when a government initiative led to a resurgence of exploration through amending the mining legislation, redirecting Government research priorities and tax changes. The economic and political and commercial environment in 2001 is very different from that of the 1960s and success of these new initiatives depends on the continuing support and involvement of all sectors of the minerals industry, and building an improved relationship with the Government and the public.

Jan 1, 2001

By Christopher Mark

Multiple seam interactions are a major ground control hazard in many U.S. underground coal mines. The two most common types are: ? Undermining, where stress concentrations caused by previous full extraction in an overlying seam is the primary concern, and; ? Overmining, where previous full extraction in an underlying seam can result in stress concentrations and rock damage from subsidence. The National Institute for Occupational Safety and Health (NIOSH) has completed a major study aimed at helping to identify the location and likely severity of these interactions. In the course of field visits to mines throughout the U.S., more than 300 multiple seam case histories were assembled into the largest data base of multiple seam case histories ever collected. These data were analyzed with the multivariate statistical technique of logistic regression. The study also employed LaM2D to estimate the multiple seam stresses, ALPS and ARMPS to determine pillar stability factors, and the CMRR to measure roof quality. The study resulted in the development of a computer program, called Analysis of Multiple Seam Stability (AMSS), which can help mine planners to evaluate each potential interaction and take steps to reduce the risk of ground control failure. AMSS first evaluates pillar design by calculating the single seam Stability Factor (SFSS) using ALPS or ARMPS. It also automatically generates a LaM2D analysis that provides the additional multiple seam stress so that the final, multiple seam SFMS can be determined. The second part of the AMSS procedure builds upon the statistical findings that overmining is much more difficult than undermining, isolated remnant pillars cause more problems than gob-solid boundaries, and weaker roof significantly increases the risk of multiple seam interactions. AMSS quantifies these effects and predicts the outcome in terms of three levels of risk: GREEN (where a major multiple seam interaction is considered unlikely), YELLOW (where adding a pattern of cable bolts or other equivalent supplemental support could greatly reduce the probability of a major interaction.), or RED (a major interaction should be considered likely, and it may be desirable to avoid the area entirely).

Jan 1, 2007

By A. A. Toprac

The recurring problem of joint failures in ofjshore structures, coupled with the catastrophic collapse of many of these structures during Hurricane Hilda (1964), hay forced reconsideration of techniques presently used to design sfuctural joints. This paper presents results of studies conducted for this reconsiderat?on. Only right-angled T-joint,s and cross-joints where a brace was welded directly to the undisturbed surface of another tube (the chord) were considered. Tests were performed on seven T-joint and 12 oross-joint specimens of two types which were designed to give a broad but practicd range to the geometrical parameters believed to be of significance to the problem. These paramefers were expressed in dimensionless form. Each specimen of the T-joints was instrumented wirh both electrical resistance strain gauges and deflection dials. After the elastic tests were concluded, each specimen was loaded to failure by applying an axial tensile load to the brace. The cross-joints were tested to failure without measuring elastic strains. Theoretical solutions for the stresses in a cylindrical shell due to a distributed radial load over portions of its surface were numerically evaluated. The experimental results are compared with calculated values obtained using Bijlaard's and Dundrova's theoretical analyses. INTRODUCTION During the last IS years a large number of structures were built for the offshore exploration of oil both in the Gulf of Mexico and dong the Pacific Coast.' In all these offshore platforms, the tubular shape was extensively used since this shape provides outstanding strength in proportion to its weight, compared to other shapes, when all directions (x, y, z) are considered. Past use of tubes was hampered because of connection details. But with the advent of welding, it became no more difficult to connect tubular shapes than to connect rolled shapes. However, some problems have been encountered in actual construction in making welded joints that are adequate and yet economical. In trying to connect tubular members, designers have used a varied number of methods; consequently, some of the joints seem to be very expensive in detail while others appear weak and underdesigned. An inspection of offshore platforms owned by different companies indicates the use of a large number of joint arrangements and configurations. Such a variety of joint types in current service indicates the wide divergence of opinion that exists on how such joints should be designed, stiffened and strengthened. Fig. 1 shows the various types of connections that have been used in practice. This paper reviews the present state of art on tubular joints of the T and cross type, and presents results of experimental and analytical work being conducted at The U. of Texas and elsewhere. It is believed that such information will be of great help to designers for the formulation of proper design procedures for joints. CONNECTION PROBLEM Recently, cracks have been observed in several welded connections in offshore structures. Fortunately, until about 1 1/2 years ago, these failures have been localized and have not resulted in the collapse of structures or loss of life. For example, one platform installed in Louisiana during 1955 in about 60 ft of water had been subjected to four tropical hurricanes. This platform successfully withstood these forces and was later removed because operations at this location had been completed. Many joint failures were observed during the removal.

By John E. Wiegand

"We will attempt to explain the basic workings of a modern seismograph and how the recorded data can be interpreted, not only for determining compliance to the regulations, but also in determining whether or not a seismograph record is accurate and valid. We will discuss some parameters that should be included in all seismographic recordings. We will give examples and use overhead slidesto show examples of both accurate and valid recordings, and tampered and inaccurate seismograph recordings. Much of the information presented will be basic in nature, and will reflect the opinions and personal experiences of the author. We ho'pe the listener will gain valuable information concerning the use and interpretation of seismographic data, as well as find interest and sometimes humor in the examples shown."

Jan 1, 1992

By M. A. Trevits, J. E. Urosek, A. C. Smith, M. P. Valoski

Unlike other types of mining accidents, where an incident generally involves only a few workers, the danger of a mine fire extends to every person working in the underground environment. Mine fires can trap or kill those working underground by blocking avenues of escape and rapidly creating heat, asphyxiating gases and toxic fire products that can quickly spread throughout the mine. The National Institute for Occupational Safety and Health (NIOSH), in partnership with the Mine Safety and Health Administration (MSHA), is conducting research to test, evaluate and improve or modify coal mine fire-fighting strategies and methodologies through large-scale tests. Because wood is the second most abundant fuel available during a coal mine fire, it was decided that a series of large-scale wood crib fire tests was needed to measure the products of combustion and to observe the capability of commonly available direct application fire suppression equipment, namely, fire extinguishers, water and gas-enhanced foam. This paper discusses the wood crib fire tests, provides insight into the products of combustion and describes observations made during the application of the fire suppression agents.1

By F Owusu-Mensah, F Nsarko

The Obuasi Mine has been in operation for the past 100 years. Within this period a host of mining methods have been employed during its various changing phases. The causes for the changes are multiple, ranging from orebody capability, dynamics, technology, safety, economics, production levels, geotechnical, etc. Mining methods applied have also ranged from timber square setts, conventional cut-and-fill, shrinkage stoping, sublevel caving, mechanised cut-and-fill, longitudinal and transverse open stoping, and lately longitudinal retreat mining method (LRMM).The Obuasi Mine has a world class underground resource potential of about 27 million ounces. A third of this is in reserve. The orebody is subvertical, with multiple lodes and with widths ranging from 1.5 - 40 m. It stretches along 8.5 km N/S strike. A cursory statistical analysis on the various resource ore widths show a higher percentage (60 per cent) of the resource being within the range of about 1.5 - 10 m. Thus a high proportion of the resource is amenable to narrow vein mining methods. This has enhanced the choice of LRMM as an alternative method. Also, with the increasing cost of mining over time, LRMM, which eliminates expensive and time consuming footwall drives, will become far more advantageous as compared to the transverse/longitudinal open stoping methods which currently constitute about 40 per cent of the total underground production.The LRMM currently delivers about 20 per cent of the Obuasi Mine production. Plans are underway to improve total underground production from the current average of 160 000 tpm to about >180 000 tpm in the next few years and about 20 - 40 per cent more in the foreseeable future. Recoverable ounces will also increase from 26 000 to about 34 000 ounces per month. The proportion of LRMM in the business plan is also expected to increase from the current modest level to about 50 per cent. Despite its tremendous advantages in terms of economics and productivity, the method is facing some challenges during its inception. The objective of this paper is to highlight some of the emerging challenges and their effect on production and offer possible remedies that could mitigate the current and possible future challenges.CITATION:Nsarko, F and Owusu-Mensah, F, 2012. The Obuasi mine - longitudinal retreat mining method application and challenges, in Proceedings Narrow Vein Mining 2012 , pp 59-70 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By Zhang Chuanfu

Keywords: modified coprecipitation method, Ni-Co alloy powders, solid-solution oxalate, growth mechanism Homogeneous solid-solution oxalates of Ni2+ and Co2+ ions were synthesized by modified coprecipitation method and the composition and morphology of the fibrous solid-solution oxalates precursor were characterized by XRD, IR, DTA/TG and SEM analysis. The effects of feeding methods, pH values, precipitation temperature, reactant concentration, addition surfactant, alcohol washing and drying process on the morphology and dispersion of the precursor were investigated in detail. The experimental results showed that the coprecipitated powders have characteristics that are different from those of the mechanical mixtures with the same stoichiometry. Based on the observations of precursors growth and SEM morphology of the precursor, the oriented attachment was proposed for the well-aligned growth of the fibrous Ni-Co alloy precursor particles.

Jan 1, 2005

By B. G. D. Smart

An understanding of the nature of yield zones surrounding coal mine excavations is fundamental to the design of mine support systems. Various methods have been designed for investigation of underground rock masses and an extensometric technique, the Magnetic Rod Extensometer, has been developed to overcome inherent design limitations in existing equipment of this type. This paper refers to the prototype form of the extensometer and details changes designed to overcome a variety of drawbacks indicated by routine use of the equipment. The principal change has been one of manual to computerised data acquisition and presentation in the laboratory phase of the system. This has dramatically reduced the time taken to process underground measurements and produce numerical and graphical results. The revised Magnetic Rod Extensometer represents an integrated instrumentation system that combines speed and accuracy in all areas of data handling.

Jan 1, 1984

By F Shi, W Huang, D Seaman, K Runge

High Voltage Pulse (HVP) technology is a novel process that could potentially be the step-change needed in ore processability in the mining industry. The propensity of high voltage pulses towards mineral-enriched ore particles during treatment makes this technology selective and has the potential to enable ore pre-concentration by size separation. In this study, the potential for pre-concentration of a low grade copper-gold ore sample subjected to HVP pretreatment is investigated and compared to that achievable after mechanical breakage in JKMRC’s rotary breakage tester (JKRBT). The data show that a better pre-concentration result can be achieved after HVP processing than conventional breakage. The gold pre-concentration potential is much better than that observed for copper. 4D HVP pre-concentration characteristic curves were produced to assess the metallurgical performance possible as a function of energy input. The case study shows that when targeting a nominal metal recovery of 90 per cent for gold, the HVP pre-concentration technique can split the low grade ore (0.9 ppm gold and 0.28 per cent copper in the feed size 26.5-37.5 mm) into two components – a low grade oversize material (0.3 ppm gold and 0.15 per cent copper) and a high grade undersize material (1.0 ppm gold and 0.3 per cent copper). The mass split to the low grade is 23 per cent. Under this mass split scenario, gold recovery to screen undersize is 90 per cent and copper recovery is 85 per cent. The HVP treatment of this feed size requires a specific energy (spark) of 2.8 kWh/t.There is further research that would be required before industrial uptake of the HVP pre-concentration technology would be possible. This paper also outlines the research challenges that need to be overcome.CITATION:Huang, W, Shi, F, Antonio, C, Runge, K and Seaman, D, 2018. High-voltage pulse pre-concentration study using a low-grade copper-gold ore, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 327–338 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018