Search Documents

By Arpit Parikh

"Ground Water or Pore water pressure development in Sandy Soil formation is Critical situation in foundation analysis and design.Moreover it become severe while associated with higher liquefaction probability in river bank areas. It is difficult to find cost optimized solution for liquefaction mitigation under limited budget allocated for the project. Here in these research paper the attempt has been made to have clear picture of liquefaction by using various techniques and field tests. And its mitigation by suitable foundation type. In Bangladesh, On Bank of River Meghana, Power plant structures are proposed. The particular site is full of fine sand having partial silt throughout from EGL to 55 m depth. Hence in addition to Conventional Boring / Drilling operations, CPLT, SCPT, SCHT and PMT had been performed to arrive deterministic effect of liquefaction. By use of Geologismiki software and some excel based programs developed which indicates that Certainly liquefaction occurs under the event of earthquake. By Checking past records of Bangladesh we found, there are small magnitude earthquakes are inevitable and frequent. Hence fourth to overcome the bad effect of liquefaction, the deep pile foundation -Driven Pre Cast Solid Square Pile of 400 mm dia. had been suggested for various types of power plant structures. Which densify the soil and ground will improve in resisting liquefaction.1. INTRODUCTIONA Detailed Geotechnical/Foundation design Analysis had been done to arrive at optimum foundation design solution in highly probable liquefaction zone of Silty Fine Sand near Dhaka City of Bangladesh for proposed 750 MW Cyclic Power Plant. Hence about 24 no. of (Borehole) Boring and Drilling up to depth of 55 m from existing ground level has been carried out. Additionally, 09 nos. of Static Cone Penetration Test (SCPT), 02 Nos. of Dynamic Cone Penetration Test (DCPT), 02 Nos. of Pressure meter test (PMT), 02 nos. of Cyclic Plate load test (CPLT) of suitable capacity with 06 nos. of Seismic Cross Hole Test (SCHT) in boreholes had been carried out. The purpose of PMT and SCHT was to have clear idea about the Seismic behavior - knowhow of site. According to Basic principles of Soil Mechanics and foundation design, it is proved that PMT & SCHT are dynamic test. These tests stimulate field condition of occurrences of earthquake. In later stages of analysis, it is found that site have high probability of liquefaction through use of Geologismiki – Liquefaction Analysis Software. Author of these research paper also felt earthquake vibrations – strong aftershocks during site study where Epicenter of the earthquake was in Myanmar during month of august 2016."

Jan 1, 2017

A paper presenting an overview of legislative and best practice approaches to the management of OHS&E and business risk for Australian tunnelling operations. Best practice can be achieved in Australian tunnelling through ærisk awarenessÆ by decision-makers and line personnel. This will identify problems before they occur and lead to implementing controls appropriate to avoiding loss throughout the life cycle of the underground opening. The author draws on legislative approaches from all Australian states together with practical experience from risk management and risk engineering work from six recent tunnelling projects. This describes a process that:commences with concept risk assessment,involves quantification of major hazards,conducts assessments of operating risks, andleads to implementation of an integrated management system that keeps construction activities connected with the controls identified in the design and planning phases and minimises the losses sustained as a result. Key points addressed include:where the industry is going with respect to risk û methods and considerations,how tunnelling risks are perceived by the industry and legislation,how tunnel constructors and owners can minimise exposure by using proper risk engineering ætoolsÆ, andreflections on best practice methods for transferring knowledge from designers to contractors/operators.

Jan 1, 2008

Increasing depths and mechanization of underground mines have led to the production of large amounts of gaseous and particulate contaminants. Over 100 000 lives have been lost due to methane gas and dust explosions in coal mine workings in both the United States and Canada since 1900. There is, therefore, the need to constantly assess and evaluate the performance of existing mine ventilation systems to maintain safe and acceptable mine environmental conditions. This paper advances research initiatives in the control of methane gas in underground mine environments. It uses the results of continuous monitoring of methane gas concentrations conducted in selected coal mines in North America to assess the effectiveness of existing auxiliary ventilation systems to control methane gas concentrations. The results show that the average quantities of fresh air required to dilute, disperse and remove methane gas concentrations within set levels of one minute varied from 5.43 m3/sec. to 27.97 m3/sec. in the development headings. The average dilution times in the headings studied were less than eight minutes. The calculated dilution efficiencies of the auxiliary ventilation systems in the headings varied from 12% to 139%. These efficiencies ranged from poor to excellent. This implies that the auxiliary ventilation systems were capable of controlling the methane gas concentrations below statutory levels but may not be able to cope with large and unusual methane gas concentrations in the headings. This study is significant in the control of methane gas and coal dust explosions in coal mines.

Sep 1, 2001

By Jerry F. Parola

In current practice, pile foundation design is based on a general under-standing of pile-soil interaction during installation and superstructure-pile-soil interaction after construction. The pile design is a reflection of experience, precedent and judgment for normal piling practice of working load capacities up to approximately 100 tons with corresponding ultimate capacities up to 200 tons. For higher capacity piles, pile design is even less predictable. In particular, the feasibility of pile installation is an important design consideration that must be given the proper attention. An installation capability that is not given the required emphasis can cause unnecessary problems.

Jan 1, 1986

By G. B. Atkinson

The Bureau of Mines investigated a method for increasing the leaching rate of bulk superalloy scrap to facilitate recycling and recovery of critical metals such as Ni, Co, and Cr. Three superalloys were investi- gated, the cast-nickel-base superalloy IN-738, the wrought-nickel-base superalloy Rene-41, and the cast-cobalt-base superalloy Mar-M-509. Superalloys melted with 20, 30, 40, and 50 pct Al metal to form inter- metallic compounds were easily crushed to a convenient particle size and reacted rapidly with acid solutions which dissolved the metals. For example, leaching 1/2-in pieces of unalloyed IN-738 with excess 6N HC1 at 95° C for 2 h dissolved about 0.5 pct, while leaching 10 g of minus 20-mesh 30 pct Al-70 pct IN-738 with excess 6N HC1 at 95° C for 2 h dis- solved 96.2 pct.

Jan 1, 1983

Coal preparation plant simulators are used to study flowsheet alternatives and determine product quality and quantity that can be produced under various operating conditions for individual circuits. Some simulators also provide an estimate of the cost per ton of clean coal by determining the number and size of different processing units required for a specific raw coal tonnage and by computing both capital and operating costs for individual units. However, to the authors? knowledge, none of these simulators have the ability to optimize plant performance while satisfying multiple product quality constraints and selecting the most profitable flowsheet from many alternatives. A novel coal preparation plant simulator (SIU-Sim) that maximizes the overall plant yield using a robust optimization tool and selects the best plant cleaning circuit configuration based on maximum plant profitability is presented. The simulator also identifies the best operating conditions for individual circuits of a plant to satisfy multiple quality constraints for the overall clean coal product. It uses a genetic algorithms- (GA) based technique to maximize the overall plant yield for each cleaning flowsheet alternative and uses a net present value (NPV) analysis technique to maximize plant profitability for the entire life of a new plant or the remaining life of an existing plant. The step-by-step development of the simulator along with a case study demonstrating its specific features is presented.

Jan 1, 2008

By AIME AIME

Maurer's review summarizes quite thoroughly the various theoretical developments and experimental findings that contribute to the knowledge of rock mechanics in drilling. This discussion supplements Maurer's paper by including generalities that either have been incompletely treated in his review, or formulated from new considerations by the discussant and from hitherto unpublished experimental data. These generalities are associated with the observation that all mechanical methods of rock drilling essentially comprise a sequence of indexed, concentrated loadings on the bottom of the hole being drilled.

Jan 1, 1967

By Joan K. Kuenzi

This Information Circular brings together for consideration recommendations from U.S. Bureau of Mines research in the area of surface mine mobile equipment maintenance for the period 1982 through 1991. It updates the 1982 contract report by Baker and Alves that formed the basis for much of the work described in the present report. Recommendations for hazard abatement during work on mobile one equipment are presented and stem from the results and recommendations of the research in two areas: (1) equipment and workplace hazard reduction, and (2) management of maintenance information. Recommendations included in this report apply to both the operators and maintainers of mobile mining equipment as well as to the manufacturers of that equipment.

Jan 1, 1995

By P. E. Walker, M. E. Reed, R. C. Sims, B. Snowdon, D. E. Fallas

An advanced Flash Furnace feed system is the key to improving furnace performance. Clyde-WorleyParsons has developed a revolutionary pulseless pneumatic injection feed system technology, capable of delivering a range of benefits to operators of Flash Furnaces. The solution was created by combining the pneumatic conveying and injection knowledge, expertise and technology of Clyde Materials Handling with WorleyParsons' flash furnace process and operating experience. Optimal furnace burner performance requires the feed material to be presented to the burner as a stable, pulseless and accurately controlled flow, distributed evenly around the burner tip circumference. These simple requirements appear obvious, but are extremely difficult to satisfy in industrial environments and are not achieved by conventional feed systems. Our analysis of existing operating furnaces has identified the link between pulses in concentrate feed rate caused by conventional drag chain conveyors and rapid fluctuations measured in the furnace pressure. These fluctuations occur at a timescale close to the reaction shaft residence time and lead to unwanted instability in the primary furnace reaction zone - the flame. Through the use of the solution created by Clyde-WorleyParsons, it is predicted that the much more accurate control of feed rates achieved can lead to substantial improvements in furnace output, increased oxygen efficiency and better control of the composition of furnace liquids, such as matte, blister or slag. All these improvements lead to significant increases in smelter output and efficiency, and deliver high economic value compared to the cost of the feed system. Clyde-WorleyParsons' solutions can be deployed on greenfield sites or retrofitted, and therefore, have the capability to improve feed control at both new and existing smelters. This paper will discuss the field test work undertaken to date, the impact of findings and the ongoing analysis of linkages between instabilities in the various components of conventional feed systems and furnace pressure stability.

Jan 1, 2007

By Imre Gombköto, Zoltán Pap, Ákos Debreczeni, Sándor Nagy

Eddy current separators have become generally used in waste recycling industry during the last decade. There are many papers dealing with separation processes on eddy current separators, and also many article describes particle trajectory and different particle features affecting particle trajectory. These data are used in modeling as well. Within the frame of R&D project called ‚Fundamental research into the exploitation of the economic development potentials of critical raw materials in international co-operation - CriticEl?, authors are aimed for using Eddy Current Separator (ECS) as a mechanical separation step of high value critical elements recovery of selected WEEE’s like display panels, PCB’s. ECS, equipped with 305 mm wide belt, and a concentric magnetic rotor is used for experiments targeted development of methodology for determining separability of different particles on ECS. The subject of our work was to investigate the behavior of model particles with different shape, conductivity (aluminum and copper), orientation and size in order to separate Al and Cu according to the results of many experiments were carried out in this field. However it looks like that throwing distance of one particle is only possible to describe by a certain distribution for even the same particle within the frame of the same conditions. Sample mean and standard deviation are depending on some of the particle feature and acting forces. The paper is going to draft the first results on the relationship between distribution of throwing distance and particle properties.

Jan 1, 2014

Improved Process & Practices Result In: ? Reduction of undesirable downtime, & expensive secondary damage ? Improved equipment performance & health ? Extension of equipment life, & reduction of operating costs ? Safety and environmental performance improvement Equipment knowledge capture and consistently applied

May 1, 2010

By Jan Pru?ka

This paper describes the sheet pile design for the Line C extension from Ládví station to the North of Prague. The first part of the paper describes the geological conditions and structural configuration of the project. Typical cross sections, the description of the construction stages, and monitoring are discussed. The second part of the paper focuses on the sheeting design method. It describes the method of dependent pressures, that is, how the pressures acting upon a structure depend on the deformation. The design process and verification methodology are described in detail with comparison of the results with in-situ monitoring.

Jan 1, 2011

By J. A. Finch, A. R. Laplante, R. Espinosa-Gomez

"The Niobec concentrator rejects up to /5% of the Nb as slimes (-10u.m). The recovery of Nb from these slimes by column flotation is being studied. An essential condition for selective flotation is slimes dispersion. A particle size analyzer, the Sedigraph 5000D, was used to monitor dispersion in plant waters with combinations of organic and inorganic dispersants and flotation reagents. Flotation reagents were particularly detrimental to dispersion with sodium silicate. The best dispersion conditions were selected for column flotation tests. These tests revealed that reagent combination had a pronounced effect on froth stability. Careful frother selection achieved good froth stability under conditions of good dispersion. Plant water increased the required dispersant concentration causing mineral depression.IntroductionSlimes (-10 u.m) rejected at Niobec contain up to 15070 of the over-all Nb content . Recovery of Nb from these slimes would significantly increase over-all recovery. A suggested recovery route involves two phases: (1) carbonate flotation (to remove most of the carbonates) depressing silicates and pyrochlore (as currently done at Niobec); and (2) selective (direct) pyrochlore flotation from the silicates. Phase 2 has been addressed and several routes to achieve selective flotation are available. Phase I was attempted with the selective reagent scheme used at Niobec but a considerable amount of pyrochlore floated with the carbonates due to poor slimes dispersion."

Jan 1, 1987

By S. Hill

For a mining operation, the determination of the best place to build haul roads is typically done by hand, or with the assistance of rudimentary shortest path optimisation algorithms. Straight line, point to point, modelling of costs is often used with distances multiplied by constants that are based on rise of the road between the points. Failings of this approach are that straight line approximations are notoriously poor as they do not take into account areas where a truck cannot travel. In addition, the rise and fall of the road may vary considerably over the truck journey meaning acceleration/deceleration and varying truck speeds are not taken into account. Lastly, the use of rudimentary optimisation algorithms means properties a truck must obey such as minimum turning circles, line of sight restrictions or even that the truck must travel forward at all times are not taken into account. Thus solutions generated may not be feasible, let alone optimal. In this paper we discuss a state of the art parallel Artificial Intelligence tree search technique for solving haul road location problems. As well as the above properties, factors such as road utilisation, cut and fill, and construction costs are taken into account. The combination of advanced modelling and fast computing and optimisation techniques produces significant benefits both in terms of time to generate roads and cost savings. Preliminary results where this method has been used are discussed.

Aug 1, 2013

By R. G. Knickerbocker, David Schlain, F. K. Shelton, J. H. Jacobs

"Many manganese ores contain from 0.1 to several percent cobalt. If such ores arc used for the production of ferromanganese, the cobalt is lost; on the other hand, if they are used for the production of electrolytic manganese, the cobalt can be recovered during the purification of the electrolyte.The production of cobalt in the United States is insignificant compared to the amount consumed, most of which is imported from the Belgian Congo. Cobalt-bearing manganese ores may therefore constitute an important reserve of cobalt in times of emergency. Moreover, the combined value of manganese and cobalt in some ores may be sufficient to warrant the recovery of both metals by the electrolytic manganese process, whereas the recovery of either manganese or cobalt alone might not be economically feasible.In view of the potential importance of manganese ores as a source of cobalt, a survey has boon made of the cobalt content of manganese ores. Most of the data have been obtained from analyses made in the Bureau of Mines, but valuable data have also been obtained from publications of the Geological Survey, various State publications, and other sources. Unfortunately, most published analyses of manganese ores do not include cobalt determinations; when such analyses were fairly detailed, but did not include cobalt, it was presumed that cobalt was not present in significant quantity.Information on the cobalt content of domestic manganese ores is given in table 1. Ores containing 0.1 percent or more cobalt are listed in table 2, and the districts in which such ores occur are shown in figure 1. Most of the known cobalt-bearing manganese ores occur in the southeastern part of the United States. A group of deposits in central Arizona and a few scattered deposits in other States also' contain cobalt."

Apr 1, 1946

By Jorge Meza

El presente texto señala la aplicación del sistema de gestión de demanda y consumo de energía eléctrica en la fundición de Southern Perú. El sistema está compuesto por un módulo predictor de demanda eléctrica y un módulo de simulación del sistema eléctrico de la planta. El primero, se construyó utilizando redes neuronales con algoritmos de aprendizaje backpropagation, capaz de pronosticar la evolución horaria de la demanda eléctrica con un porcentaje de error cercano. Mientras que el segundo está basado en técnicas de estimación paramétrica, redes neuronales y ecuaciones matemáticas obtenidas por regresión estadística, que simula el comportamiento del sistema de energía eléctrica de la fundición. En ese sentido, los módulos facilitan una adecuada planificación, ya que permiten conocer el comportamiento de la demanda horaria y los patrones de consumo de la planta, incluyendo los componentes de la facturación. Así como las deficiencias energéticas y oportunidades de mejora, sobre la base del análisis de la información acerca de los equipos, procesos y planes de producción, así como programas de mantenimiento.

Sep 24, 2008

By S. Saeed, N. Coulson, P. F. Stewart

"The Mine, Health and Safety Act No. 29 of 1996, as amended, embodies worker self-regulation to advance health and safety in the workplace. An important provision for this is the Right to Refuse Dangerous Work (RRDW). This paper explores worker perspectives about the implementation of RRDW on South African mines against a backdrop of revised guidance in the sector: ‘Guideline for a Mandatory Code of Practice on the Right to Refuse Dangerous Work And Leave Dangerous Working Places’, gazetted in February 2016 by the Department of Mineral Resources (DMR). A mixed methods study conducted at mines (n = 14) included a survey of workers (n = 293), focus groups (n = 6) and in-depth interviews (n = 16). Workers reported a high level of awareness, a positive attitude, and experience of the formal RRDW. However constraints to the formal RRDW meant that informal worker resistance to dangerous work was commonplace. Evidence of informal non-confrontational consultation, cooperation, and collaboration in the event of a dangerous workplace also emerged between workers, and supervisors. The research underscores the importance of the RRDW and worker health and safety representatives to mine health and safety. The revised guidance addresses RRDW implementation gaps, but of concern is the potential partiality towards management interests. IntroductionEnsuring that mineworkers act on their duties and responsibilities for health and safety remains a concern across the globe. Article 13 of the International Labour Organization (ILO) Convention Safety and Health in Mines (176 of 1995) entrenched the Right to Refuse Dangerous Work (RRDW) as an important mechanism through which workers act in the best interests of their own occupational health and safety (OHS) and is considered a cornerstone of worker self-regulation (ILO, 1995). Countries ratifying Convention 176 are under obligation to make this right available to workers through OHS legislation that frames the circumstances, procedure, and protection of workers from discrimination in the event of a formal work refusal. The Convention has been ratified by 31 countries, with South Africa becoming a signatory in June 2000 (ILO, 2000). Worldwide studies show that workers use this right with caution (Hilgert, 2013) and cases associated with work refusal are rarely presented in court (Gunningham, 2007; Cooper, 2013). Rather, in cases of formal notification of a work refusal, issues arising out of this are addressed either in the immediate workplace or through the site OHS system and/or at industrial tribunals or similar mechanisms (Harcourt and Harcourt, 2000)."

Jan 1, 2018

By A K. Raina, V M. S R Murthy

Rock mass response in blasting is an important element to determine the performance of a blast along with its other outcomes. The near-field monitoring for rock mass response analysis is vital for determining the behaviour of a blast; however, due to costly and cumbersome methods involved in such measurements the subject has received scant attention so far and the publications on this account are perfunctory in nature. This paper presents a non-destructive method to monitor the blast-induced pressure in the rock mass at a distance from a blasthole. The methodology of monitoring and a few examples of actual field monitoring are detailed in this paper. The responses of the rock in the near-field of a blasthole under dynamic loading have been documented to predict fragmentation and throw. The proposed method has also been used in limited cases earlier by the author to predict flyrock using a semi-empirical method and trajectory equation. The pros and cons of the method are discussed while throwing light on the actual response and the prediction of fragmentation and throw of blasted rock.CITATION:Raina, A K and Murthy, V M S R, 2015. Measurement of blast-induced pressure in bench blasting and deciphering explosive performance through rock mass response analysis – a methodology, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 501–508 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Howard H. Fields

Any mining engineer with a desire to operate independently, with some financial backing, and with no fear of heavy responsibility and long hours, should be able to make a comfortable living in Mexico. Barring a few inconveniences such as a lack of satisfactory liability or accident insurance, the difficulty of obtaining repair parts or vehicles, and the length of time required to receive returns from shipments, the operation of small mine is not at all difficult. It is, in fact, a little easier to find a good prospect in Mexico than in the U.S.

Jan 1, 1950

By William J. Campbell

One of the principal objectives of the Bureau of Mines program for developing super refractory materials is to obtain fundamental data on the physical properties of refractory oxides. This particular investigation obtained accurate thermal expansion coefficients for alpha alumina and evaluated, critically, those coefficients with other published values. High-temperature X-ray diffractometer measurements, by the Bureau, showed that alpha alumina expands anisotropically with expansion parallel to the c axis approximately 10 percent greater than parallel to the a axis. Thermal expansion characteristics of four different alumina samples were determined up to 1,200° C.; the results are presented in both tabular and graphical form. The combined random and systematic errors in the measurements are considered less than 3 percent above 500° C, and approximately 2 percent at 1,000° C. No differences in expansion were observed between the samples or between the heating or cooling cycles.

Jan 1, 1961