Search Documents

"Mining with blast holes drilled upwards may be done to recover sill pillars, or for economic reasons when the distance between the levels is relatively large. If the rock is sufficiently competent to accommodate large stope size, the distance between sublevels could be increased to as much as drilling accuracy allows. The same drill drift can be used for the drilling of both down holes and up holes. In the case of down holes, the initial opening of the stope (drop raise) is not as much a problem as for the inverse drop raise for mining with up holes. This is because, with a drop raise, a lot of space is available at the toe for the blasted rock to expand. In addition, the raise can be blasted in many shots, thus allowing smaller blasts each time. Inverse drop raises are generally much more difficult to blast because of the limited space for muck flow, and must, therefore, be taken down in a single blast, requiring special considerations in order to ensure a success. A case study of a 29 m (95 ft) inverse drop raise successfully blasted in a single shot at Heath Steele Mines is described. The paper covers technical considerations such as drilling accuracy, hole deviation survey, delay extension and protection, initiation methods and initiation sequence. Finally, a novel method for creating the initial opening called ’slot drilling’ is presented. This method, inspired from LKAB in Sweden, consists of drilling a row of interconnected holes using a special guide mounted on a regular production drill hammer.With a case study of blasting an inverse drop raise of 29 m (95 ft) in one blast, this paper further discusses some technical issues that are critical for the development of inverse drop raises. A novel method for creating the initial opening with a slot of interconnected holes is also presented with the experience acquired at different mine sites across the Noranda group."

Jan 1, 2000

By Olli Haavisto, Juha Timperi

"Accurate on-line assays of mineral slurries are the basis for effective operation of flotation circuits. Typically the elemental content measurements are obtained by an X-ray fluorescence (XRF) analyzer, which samples the process lines and performs the analysis concurrently line-by-line. For a more frequent measurement of each slurry line the XRF measurements can be complemented with reflectance spectrum information. In reflectance spectroscopy the absorbance properties of the slurry in the visible and near-infrared wavelength range are analyzed. The advantage of reflectance spectroscopy is that measurements can be obtained quickly and simultaneously from several slurry lines. However, since the shape of the spectrum is only indirectly affected by the slurry elemental contents, frequent calibration of the measurement against the XRF analyzer is necessary. This study elaborates the combination of reflectance spectrum analysis with XRF. Results of laboratory tests for different slurries are presented and the operation of the system in a copper-zinc flotation plant is demonstrated.IntroductionElemental analysis of mineral flotation slurries is the most important factor in evaluating the performance of concentration processes. Timely on-line assays are also used as the basis for controlling the circuits and ensuring that the grade and recovery targets are reached. X-ray fluorescence (XRF) is the dominant technology in on-line elemental slurry analysis, and typically centralized XRF analyzers are used. The advantage of a centralized analyzer is that one measurement probe can be used to acquire the data from several slurry lines. This reduces the overall operating cost of the system when compared to distributed analyzer system design with several measurement probes requiring maintenance and spare parts. Slurry samplers are installed in the interesting process flows and representative sample flows are brought to the analyzer, where the slurry is further sampled and measured consecutively by the XRF analyzer. Due to the centralized structure of the analyzers and consecutively measurement of the sampling lines the sampling interval per slurry line can be relatively long. In larger concentration plants with several sampling lines a typical assay interval is in the range of 10-20 minutes."

Jan 1, 2016

Factors leading to the necessity for some individual testwork in solving most specific hydraulic transportation problems are listed and a description is given of a method used in determining critical flow conditions. An outline is given of the basic theory of the purpose of the testwork, and a means of applying test results for varied pipeline diamet.er and material conditions follows. Engineering and economic factors are applied to the solution of a specific hydraulic transportation problem and the use of the test results in plant practice is illustrated. The advantages of connecting pumps in series in centralised pumping stations rather than individually along the pipeline are stressed. Some notes are added on the future possibilities and economies of post pump injection of solids into high pressure pipelines.THE HYDRAULIC TRANSPORTATION OF SANDSAs well as all the classical variables involved in a pipeline installation, one must consider, when solids are to be transported, the effects of such variables as:(i) Proportion of solids in the pulp.(ii) The average specific gravity of the pulp.(iii) Specific gravity of the solid material.(iv) Solid particle average sizing and possibly shape.(v) Solids particle grading.(vi) Pipeline diameter for effects other than classically hydraulic.(vii) Pipeline material.(viii) Fluid viscosity.(ix) Pump characteristics.(x) Abrasive or corrosive properties of the pulp.Not surprisingly, the application of published data to the hydraulic transportation of a specific material is difficult if not well nigh impossible. Most hydraulic transportation investigations also involve economic and site factors vary...

Jan 1, 1959

By Don Z. Painter, Gordon F. Revey

Frontier/Traylor Joint Venture is presently constructing a section of the Tri-County Metropolitan Transit District of Oregon's (TRI-MET) Westside Light Rail system. This new section will extend Portland's existing transit system to the western suburbs of Beaverton and Hillsboro. The drill-blast excavations at this project include 10,000 feet of 20 foot tunnel, 18 cross passages, three shafts, an underground railway station, and a U-wall open cut. From a blast designer's perspective, this job has been extremely challenging. Blast vibration is limited to 0.5 ips at 200 feet or at the nearest structure, and airblast is limited to 129 dB -- linear peak and 96 dB -- C scale. The tunnels pass under heavily built up areas and have top of tunnel to surface cover distances as low as 70 feet. Surface blasting in the 26,000 cubic yard U-wall excavation was limited to five short nighttime periods due to its proximity to the very busy highway 26.

Jan 1, 1995

By D O’Dea, B Godel, T Honeyands, B Ellis, T Harvey

X-ray computed tomography (XCT) is a non-destructive technique that allows the exploration of the internal structure of solid objects in 3D. Over the past ten years, the combination of XCT with more conventional 2D techniques and quantitative 3D image processing and analysis (commonly referred to as digital rocks) has allowed us to address some of the most challenging problems in ore deposit studies. The range of X-ray energies used in XCT allows the X-rays to be transmitted through complex and dense materials including iron ores (eg sinters, lumps, granules). Recent high-resolution XCT scanners have the ability to generate multiscale (25 down to 0.3 µm voxel size) imaging of a given sample enabling the characterisation of 3D textures across a range of scales. This paper will focus on the application of digital rocks to iron ore sinter particles (using filtered polychromatic X-ray beam). The paper is divided into three parts and includes: i) details on the methodologies including their benefits and limitations and the effect of spatial resolution; (ii) the quantification of pore network topology and pore characteristics (eg open versus closed pores, pore size distribution and pore morphologies; degree of connectivity of the pore network and its tortuosity); and (iii) the evaluation of the technique to characterise various phases within the material and quantify 3D mineral textures.CITATION:Godel, B, Ellis, B, O’Dea, D, Honeyands, T and Harvey, T, 2017. Digital rocks for iron ore sinters – towards a D quantification of sinter textures, in Proceedings Iron Ore 2017, pp 529–534 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By V. R. Degner

The trend in both the metallic and non-metallic mining industry is toward processing increasing y higher tonnages of lower grade ores, thereby resulting in a growing interest in progressively larger volume individual machines in the flotation circuit. Because of the relatively high cost of large flotation machine development and evaluation, it is important to establish a rational basis by which the existing smaller flotation machine experience can be extrapolated to establish the configuration of the next larger family of flotation machines with a minimum of development modification in the field. This paper reviews the R&D approach used in translating smaller flotation machine experience to establish the configuration of a 1000 cu ft (2B.3 cu m) induced air machine. Internal cell hydrodynamic principles, which governed this extrapolation, and cell (liquid) surface and froth management considerations will be reviewed, and prototype machine mill tests will be summarized.

Jan 1, 1978

By Robert Dickson

Princess colliery is operated by Old Sydney Collieries, Limited, a direct descendant of the General Mining Association of London, England, which, in the first quarter of the nineteenth century, pioneered in coal mining in Nova Scotia. The coal worked is a 5 ft. 6 in. seam known generally through the Sydney coalfield as the Harbour seam but referred to locally as the Sydney Main. Entry is made by shafts, 680 feet deep, sunk in 1871 on a headland forming the northern entrance to Sydney harbour. From them extend the main roadways of the colliery, a distance of 700 feet to the shore line and a further distance of 14,700 feet in submarine areas to a total length of 15,400 feet. It was the first colliery in Nova Scotia designed to work submarine areas. Lateral development extends across a frontage of 16,000 feet and the submarine area from which the coal has been extracted is slightly over 6 square miles. There yet remains sufficient territory ahead of the workings to assure a future life to this colliery estimated at over 80 years at the current rate of production. In this area the seam dips at 6 to 7 per cent and face workings have reached a depth of 1,690 feet below the sea level. Until 1923 extraction of the coal was by room-and-pillar, followed by the drawing of the pillars. At that date the superincumbent strata had reached a thickness of 1,400 feet, resulting in heavy weighting on the roof and severe side pressure on the coal ribs. In combination with a soft, heaving pavement this created a set of conditions involving great difficulties and expense in keeping open places driven in the solid sufficiently long to permit recovery of the coal in the pillars by methods and equipment then available. The operator was forced to resort to extraction by longwall as the only economical method of winning the coal.

Jan 1, 1948

Project cost control procedures and computer systems have enjoyed a successful and simple relationship over the past decade, thanks primarily to the proliferation of portable computers or PC's. Prior to the introduction of this technology, project control was largely a manual and somewhat onerous task of historical data compilations, with little time available for dynamic forecasting, staged planning, or pre-emptive cost control. Automated systems developed during this era were resident on "Heavy Iron" or mainframe computers and were expensive to maintain and operate. Use of these early systems was limited to large engineering, construction, and industrial concerns with the economies of scale and funding required for their successful application. Systems were either designed for critical path analysis or task scheduling, but rarely integrated with the other, much less cost control.

Jan 1, 1990

By Oliver C. Ralston, and others

"INTRODUCTION Investigations of the Nonmetals Division are now conducted at College Park, Md.; Tuscaloosa. Ala.; Seattle, Wash.; and. Norris, Tenn. The last of these was acquired, this year by arrangement with the Tennessee Valley Authority and is engaged in electrothermel research, using power generated by the T.V.A. and. raw materials from that region. In general, the work of the division is concerned with dressing nonmetallic minerals end utilizing the products there-from. Coal, salts, and waters are investigated, and the suitability of apparatus and equipment is studied.As the Metallurgical. Division of the Bureau of Mines makes routine tests of certain nonmetallic ores under prescribed conditions for the public if they are of general interest, the published reports of that division should be read and thus, with the reports of tile Nonmetals Division, the whole field may be covered."

Oct 1, 1939

By Hewitt Wilson

A review is given of the nomenclature, sources, imports, statistics, common methods of preparation, and testing of mineral pigments. A description of the Deer Park-Spokane colored-clay district and the laboratory methods of preparation of these colored clays, others, and siennas follows. The mineral pigments were prepared by washing or grinding the original material as received and by calcination of the yellow ocher and brown sienna with and without manganese dioxide to produce red, brown, and black colors. These prepared powders were tested for fineness, oil absorption, and color as compared with well-known brands of commercial pigments. Similar tests were made with several basalt red clays occurring in the neighborhood of Salem, Oreg., and Kalama, Eatonville, and Clay City, Wash. The color particularly was studied, since this property is the most important commercial characteristic of the minerals. PURPOSE OF INVESTIGATION Since the development of the clay industry in the Pacific Northwest, some curiosity and interest have been aroused by the red and yellow clay or ocherouslike material that has often been found associated with the commercial clay deposits. These include the red and yellow "paint pots" near Deer Park and Spokane in eastern Washington, a red clay at Clay City, another close to Eatonville in western Washington, and red basalt earths near Salem, Oreg., and along the Columbia River near Kalama, Wash. Several companies have been organized to produce pigment colors from two of these deposits but have either discontinued or never started operations.

Jan 1, 1929

By Madgwick J. C

A novel, microaerobic, heterotrophic microbial leaching system for manganese dioxide is described. Mixed natural microflora were enriched by addition of sugars and crude plant nutrItIOnal supplements. Between 84 and 104 mg MnH was solubilized per gram sugar at I per cent (w/v) concentrations for fructose and galactose in the presence of 0.03 per cent w/v dried microalgae (a Chlamydomonas species). Some 42 per cent soluble manganese was dissolved by microbial action on MnO, (3 per cent (w/v) pulp density) using a 10 per cent (w/v) molasses growth substrate.

Jan 1, 1983

By David G. Adam

Syncrude Canada Ltd. is currently mining over 120 million tons per year of overburden and oil sands to produce 40 million barrels per year of synthetic crude oil. Production increases are planned. This paper reviews the technical and economic assessments of feeder breaker applications in both ore and waste mining which led to an extensive testing and development program and finally to the procurement of full scale production equipment.

Jan 1, 1985

The National Institute for Occupational Safety and Health (NIOSH) conducted field tests to evaluate the effectiveness of a wet head continuous mining machine for reducing dust exposure for continuous miner operators. Wet head technology delivers water via sprays to the continuous miner?s cutter head as opposed to traditional standard sprays located on the boom and body of the mining machine. The sprays, positioned directly behind each bit on the cutterhead, deliver water at the point of attack, serving to cool the bits during mining to reduce the potential for frictional ignitions. The sprays also flood the coal with water to potentially suppress dust generation. Dust surveys were conducted at several mines to evaluate the wet head?s effectiveness to control respirable dust exposure at the continuous miner operator location and in the immediate return. Results show that the wet head miner generally improved air quality at both sampling locations to varying degrees in some, but not all, mines when compared to a continuous miner with a standard spray system.

Jan 1, 2010

By J. Marsden

Lift height, overall heap height and climate all play an important role in determining precious metals leaching rates, recoveries, operating costs and capital cost requirements for heap leaching operations. The effects of these factors are not easy to predict from testwork, and this can result in unexpected delays in metal production, lower recoveries than expected and higher capital and operating costs than necessary. This paper investigates the economic impact of lift height, overall heap height and climate on heap leaching and provides criteria to assist in the design and operation of leaching facilities. Descriptions of three heap leach operations in the western USA are provided to support the discussions and conclusions.

Jan 1, 1995

By Davi Silva Braga, Alexssander Lopes Sampaio, Rodrigo Carneiro de Oliveira

Vallourec was world pioneer in the deployment, development and consolidation of technology for the use of pulverized charcoal as the main energy source on the first Grate-kiln pelletizing plant in Brazil. The objective of this work was to delve into the subject and to bring more information about this innovative practice of Vallourec that has been attracting the attention of other companies in the steel industry. Industrial tests confirmed the technical feasibility, taking Vallourec ahead in the project of adaptation and investment. With consolidated data of two years and five months from the beginning of the implementation, the main benefits are the average reduction of CO₂e emissions by 50%, cost reduction higher than expected and return on investment in just 19 months.

Oct 1, 2019

By J. H. Crary

This report summarizes the results of a one-year agreement for research on the electromagnetic environment in coal mines, which was conceived as the beginning of a long term cooperative program between ITS and the Bureau of Mines. The concepts on which it was originally based are a result of the report on mine rescue and survival by the Committee on Mine Rescue and Survival Techniques of the National Academy of Engineering, dated March 1970. This report drew particular attention to the need for improved communications during and following mine disasters. In particular, the outstanding problems identified were the location of, and communication with, trapped miners. Some tentative solutions, generally involving long-wave electromagnetic signals, were offered. Consideration of the problems of disaster location and communication soon leads to consideration of the communications techniques (or lack of them) for use under normal mining conditions. In particular, if a disaster communication and/or location system is to be readily available and operable under disaster conditions, it should also be usable during mining operations. In this way operators can become familiar enough with the system to operate it during disaster conditions, as well as provide a mechanism for regular testing.

Jan 1, 1972

By Mark P. Meyer

During 1991 through 1993, the U.S. Bureau of Mines (Bureau) -Alaska Field Operations Center (AFOC) in cooperation with the Bureau of Land Management (BLM) -Arctic District Office and the State of Alaska, Division of Geological and Geophysical Surveys (ADGGS), conducted exploration, geological, geochemical, geophysical, mineral resource, and mineral potential investigations in the 6.7 million hectare Colville Mining District (CMD) study area. This mining district study area, located in northern Alaska, includes the Colville River drainage basin as well as 0.35 million hectares of the southern part of the National Petroleum Reserve in Alaska (NPRA). This investigation was conducted as part of the Bureau's continuing Mineral Land Assessment (MLA) mining district program. The Bureau's MLA mining district program is designed to provide reliable and comprehensive mineral resource information that supports mineral resource policy and land use decisions made by Congress and Federal land management agencies.

Jan 1, 2011

By C T. Hollick

Conventional processing of heavy mineral deposits containing radioactive rare earth minerals such as monazite and xenotime may cause industrial hygiene problems through atmospheric dust and contamination of product concentrates. An alternative procedure has been developed in which such minerals are removed from bulk heavy mineral concentrates by flotation with little loss of other economic minerals. With fine ores, recoveries of over 95 per cent have been achieved and with coarse ores over 80 per cent, in both cases at high grade. Several flotation regimes have proven effective. The potential for generation of radioactive dust or product contamination is subsequent processing is correspondingly reduced.

Jan 1, 1990

By A. Anani

The need to optimize surface mining operations has led to the use of discrete event simulation (DES) modeling of truck-shovel systems. Often, these models assume truck cycle times are independent and identically distributed (iid) random variables, although, with significant bunching on the haul routes, this may not be valid. The objective of this paper is to present a methodology to (i) account for truck bunching due to slow trucks; and (ii) test for cycle time dependence (i.e. whether truck cycle time data is iid or not). We built a DES model that accounts for bunching due to a slow truck(s) and used the cycle times as data for further analysis. We then tested for cycle time dependence using Pearson correlation coefficients. The results show significant correlation of truck cycle times for different number slow trucks, with variable speeds. Assuming iid in modeling results in over-estimation of productivity and the uncertainty surrounding it. The over-estimation of uncertainty is pronounced when the relative difference in truck speed increases. The confidence interval of the means of truck loads/shift decreases with increasing number of slow operators. This work extends the usefulness of DES in truck-shovel applications.

Feb 27, 2013

By D. R. Nagaraj, Napoleon Tercero, Raymond Farinato

Historically, as for most reagents used in flotation, the wide-spread use of dialkyl dithiophosphinates as collectors in practical applications has preceded a detailed scientific understanding of how they work. Dialkyl dithiophosphinates are a technologically and commercially important class of collectors used in the flotation processing of Cu-Au, complex polymetallic, and precious metal ores. Plant usage has demonstrated that dithiophosphinates exhibit higher selectivity and flotation rates for Cu sulfides, galena, and precious metal values in the presence of other gangue sulfides, than the traditionally used collectors such as dialkyl dithiophosphates and xanthates. They also have an attractive health, safety, and environmental (HSE) profile. Although dithiophosphinates received little attention in the past in the flotation research community, recently, there has been significant interest in this chemistry, and numerous studies have been conducted to understand the fundamental interactions of dithiophosphinates with several base metal sulfides and precious metals. A critical overview of fundamental studies, laboratory ore flotation, and plant practice of dithiophosphinates is given in this paper. The findings from these studies are rationalized and explained by drawing on concepts and insights from coordination chemistry. A comparison between the interactions with various minerals and metals of dithiophosphinate and dithiophosphate analogues brings out some of the subtleties that seemingly minor changes in collector chemistry can make. The critical overview and analysis given here is useful in identifying gaps in knowledge regarding this important class of compounds. This in turn can provide a basis for the design of studies to advance our understanding of dithiophosphinate flotation performance.