Search Documents

By H. B. Jensen

STUDY of the thermal-solution process was begun by treating crushed oil shale in a small autoclave at temperatures of 700° to 950° F. The effect of temperature, reaction time, type of solvent, and richness of shale upon the amount of organic matter that was removed from the oil shale was thus determined. Following this orientation work a semicontinuous, bench-scale apparatus was built so that heated solvent could be pumped through a bed of shale under elevated pressure, thus removing the converted organic matter from the spent shale. After some operating experience had been gained, a continuous unit was constructed. This permitted treating a slurry of shale oil and pulverized oil shale at about 300 p. s. i. and temperatures of 750° to 850° F. for various retention times. Considerable cracking and polymerization of the shale oil were found to take place during the process. In an attempt to prevent this, a study was made of extraction of the shale in batch-type autoclaves under high partial pressures of hydrogen at total gas pressures of as much as 4,300 p. s. i. at 850° F. The thermal-solution process was found to convert over 90 percent of the organic matter in oil shale to oil and gas. The highest yields of gas and oil obtained without hydrogen pressure were equivalent to 119 weight-percent of those obtained from the same shale by Fischer assay. With a high partial pressure of hydrogen, yields equivalent to 126 weight-percent of Fischer assay were obtained. However, the oil produced by thermal solution has a higher boiling range than that obtained by other retorting methods, particularly so if the thermal-solution process is used without a high partial pressure of hydrogen. Nondistillable oil (all benzene-soluble material that would not distill under 2 mm. Hg absolute pressure without cracking) equivalent to over 100 percent of the organic matter in the shale was obtained without hydrogen pressure in the system. When the process was carried out under hydrogen pressure, the yield of nondistillable oil amounted to 60 to 70 weight-percent of the organic matter. Part of this heavy material is formed partly by polymerization and condensation of the shale-oil solvent used. These reactions, as well as cracking of the solvent to form gas and a carbonaceous deposit on the shale, are unfavorable features of the process.

Jan 1, 1953

By R. T. McAndrew

Introduction Drinnan is situated in the Prairie Creek coal area in the Foothills belt of Alberta. It lies on the main line of the Canadian National railway from Edmonton to Jasper. The exact location is shown on the map (Figure I). Interest in the field was aroused by several circumstances: Its proximity to Brule and Pocahontas on the southwest and to Coal-spur on the southeast led to the belief that coal might be economically produced here. There was already at Hinton a 3 ft. 9 in. coal seam being mined by Seabolt. The coal was of very good grade, being black and shiny in appearance with well defined cleavage and a heat value of 12,000 B. t.u. Outcrops of coal had also been noticed on the north side of the Athabaska river and Fish creek. These facts led the Jasper Coal Company to investigate the field. This Company considered taking over the Seabolt property at Hinton, but, owing to the size of the seam, this plan was abandoned and prospecting by diamond drills and test pits was started two years ago in the district east of Hinton. After prospecting had been completed, the most favourable district was found to be in township 51, ranges 24 and 25, west of the 5th meridian. The Company's lease includes all or parts of sections 18, 19, 20, and 28 in range 24, and sections 10, 11, 12, 13, and 14 in range 25. The approximate boundaries of the property are the Canadian National railway on the north, Happy creek on the west, and Cache Percotte creek on the east. The lease comprises 3,100 acres, and the total amount of coal in sight is estimated at 100,000,000 tons.

Jan 1, 1931

By J. Murdoch Mackenzie

Two commercial nickel solvent extraction plants treating laterite leach solutions and using LIX®84-I have been operated in Australia. These circuits employ similar extraction chemistry but differ in their leaching and stripping operations. An alternative process involving elements of both can be conceived. The preparation of the feed solution to solvent extraction plays an important role in nickel extraction using LIX®84-I and the special features of manganese removal and cobalt oxidation in the preparation of the PLS are discussed. This paper compares these three circuit configurations with special reference to the extraction and reductive stripping of cobalt, the transfer of zinc and copper to the strip aqueous, ammonia transfer and sulfur transfer. The potential degradation of the organic and remediation using re-oximation is discussed. Keywords: Nickel, Solvent Extraction, Oxime

Jan 1, 2004

By Jr. Koch

As a part of a larger study of the distribution of metals within ore deposits, the geometry of distribution of gold, silver, lead, copper, and zinc in five veins of the Fresnillo mine, Zacatecas, Mexico, was established. The purpose was to obtain basic data necessary for evaluation of geological theories about processes of vein formation and useful for practical mining applications in ore estimation and prediction of ore beyond present workings. The Bureau of Mines investigation comprised statistical analysis of 64,000 assay values from some 16,000 mine samples. The samples were taken at 2-meter intervals in drifts exposing the veins through a vertical range of some 750 meters. Within individual veins, the metals are distributed in dome¬like patterns with highest metal contents tending Lo occur in oreshoots at the centers of the developed parts of the veins. However, in the block of ground containing all five veins, base metals define mathematical domes with highest contents near the center; precious metals define mathematical basins or troughs with low contents near the center. The ratio of silver assay values to lead assay values corresponds to two geographically distinct types of mineralization: one in which silver is closely related to lead, and another in which silver is independent of lead. Other metal ratios also vary regularly from one place to another. The statistical methods employed in this study would be useful for other geologists or engineers who need to analyze large amounts of assay or similar numerical data.

Jan 1, 1967

By V. Galla

Waste rock facilities (WRF) generally have a large footprint depending on the strip ratio the mine plan provides. Considerable planning is involved during the initial phase of the mine plan regarding the location of the WRF. As the mining operations are commenced the locations of the WRF change accordingly with the variations in the mine plan involving feedback and support from local communities and stakeholders. Waste rock facilities management becomes challenging when the area available for placement is limited due to terrain topography, environmental and permitting constraints. Risks associated in the design of waste rock facilities constitute particle size of rock, chemistry associated with the rock for reactivity and stability of the over all facility. This paper will provide some insights on designing, scheduling and managing a WRF. Emphasis on geotechnical, geophysics and geochemistry aspects of waste rock with reference to design, construction process and scheduling of WRF are also presented. Design improvements in the reclamation slope of WRF for erosion control will be discussed. Continuous improvement (CI) methodology will be introduced in the process of WRF operations. Current practices and future recommendations towards sustainability and consistency in operating WRF will be discussed in conclusion.

Jan 1, 2011

By Barry Hope, Javier Rico

"Goldcorp’s Hoyle Pond mine has recently completed several projects which have impacted the overall ventilation system. The project includes extending the Fresh Air Raise (FAR) to depth, development of a new Return Air Raise (RAR), and the installation of new sensors and ventilation controls throughout the mine. Two years after the completion of #2 Winze, the mine is ramping up its ore production to 1,300 tpd (up from 1,100). To ensure safe and profitable production, a reliance upon technology has been needed to provide the required ventilation to the work areas according to the mine plan. To systematically assess the mine’s ventilation in real-time, a significant increase in remote monitoring was required. This included installing additional flow, pressure, temperature and gas sensors. The first step in upgrading the existing monitoring was to purchase airflow and differential pressure monitors and install them in key areas of the mine. This paper presents the process of expanding the monitoring capability at Hoyle Pond mine, the selected equipment and the results of the implementation. The intended goal was to improve safety while minimizing capital and operation costs. The monitors were installed in strategic locations to provide immediate feedback on the impact of changes to the primary ventilation airflows. Comparing the available sensor technologies, installing them and systematically monitoring the ventilation served as a first step towards developing a mine wide Ventilation Control System. In addition, the initial state of the monitoring and control system, with final results and the chosen solution for the mine site, are presented. INTRODUCTION The Hoyle Pond mine is located in the City of Timmins, within the Porcupine mining district, Ontario, which has produced more than 70 million ounces of gold since 1910. Currently, approximately 60% of Porcupine Gold Mines gold production comes from the Hoyle Pond underground mine. Mechanized cut and fill and long-hole mining methods are used to extract the ore. The remainder of the ore comes from the Hollinger Open Pit mine. The Dome Underground mine ceased operations in 2017. Hoyle Pond is currently mining at 1820 meters below the surface and plans to go deeper. The average dry-bulb as wet-bulb temperature underground varies according to the depth and surface conditions which has extremes of –40°C in winter to +30°C in summer. The total airflow volume pushed down from surface is 240 m3/s to accommodate the diesel-powered equipment needed for normal operations. In order to improve the quality of air underground a program has been implemented to use diesel particulate filters, starting with the truck fleet and 6-yard scoops, followed by the intention to implement the rest of the functional diesel-powered equipment and eventually move to electric equipment."

Jan 1, 2019

By Daniele Tolazzi

In today’s highly competitive market situation, it is of outmost importance for EAF steel makers to optimise their processes in order to reduce operating costs and to improve safety and reliability of the equipment. The laser based off-gas analysis technology, With laser units installed on the fix duct, downstream the combustion gap, uses the “Tuneable Diode Laser Absorption Spectroscopy” (TDLAS). The system performs real-time off-gas emissions measurements of CO, CO2, O2, H2O and temperature. A closed-loop operation is in place for dynamic control of the chemical energy package combustion/post-combustion of CO, H2 and CH4 gases into the EAF furnace shell. A statistical framework which builds on a data analysis engine, based on Danieli Automation Q3Intelligence technology, evaluates the “fingerprint” of the process represented by average and deviation trends of both gases and other process parameters. Process fingerprinting is conceived both for offline profile optimisation and on-line control of the refining process. This paper describes how the technology has been applied and the results achieved at ACCIAIERIE BERTOLI SAFAU (Italy) 100 t AC Electric Arc Furnace.

Aug 16, 2017

By Jeremy Fletcher

In today’s world, the requirement of Steel Producers to revamp and modernize their blast furnaces on-time, safely and with the latest technology is paramount. In addition they must meet the detailed design, construction and safety legislation and regulations, which can be different for the various countries around the world. Siemens MT is renowned for its ability to perform Blast Furnace rebuilds, relines and modernisations within extremely tight time frames and in a safe manner. Modular Blast Furnace construction concepts have been perfected to minimise project duration and plant downtime for furnace rebuilds. Safety and certainty are the keys for success. Siemens MT are constantly introducing new technologies into the market place including cyclone gas cleaning and triple external cone gas scrubber, along with step changes in technology such as dry gas cleaning and dry slag granulation. The economic environment and the continuing requirement for improved environmental performance, drive many of these innovations. This paper describes some of the latest rebuild reference projects of Siemens MT, along with the latest technical innovations installed on these furnaces, and some of the construction methodology used for a safe and secure rebuild.

Aug 1, 2018

By Scott Turner

I have been asked to speak briefly about recent progress in the mining industry of the United States, and to touch on the general advancement of en- gineering science as applied to mining. By recent, I shall mean within the past 20 or 30 years. Such a period includes a great many of the changes which are of particular interest to the present generation of engineers, and the undergraduates of today will hardly turn back farther than the beginning of the present century in their study of develop- ment of methods and processes. Also, my own professional life spans this period, and I have seen or have been aware of most of these developments as they were taking place. In my review of developments, for the sake of simplicity and clarity, I shall deal separately with improvements in metal mining, coal mining, mechanical and electrical machinery for mines, metallurgy, petroleum engineering, and safety practices. Under each of these headings I have set down what appear to me to be the outstanding changes brought about during the past 2 or 3 decades. Other points will occur to other engineers; I do not represent that the following re- view is complete; it is only intended to be suggestive. In general, improvements in mining and metallurgical practices have come gradually, the charges being effected little by little, simultaneously in widely scattered places, and through the experience and inventive genius of many men. These changes have has small beginnings, and are generally the cumulative result of many steady and unsensational progressions, which still continue. What we today might be inclined to consider the culmination of a series of betterments in mining is, of course, but an instantaneous phase of developments which will continue in the future at even a more rapid pace than they have in the past. We are looking at but a flesh of a moving picture, with an endless reel to come after we finally leave the theatre. Behind all the changes in the mineral industry, the driving force has been the increasing demand of an expanding population for more metals and minerals with which to advance civilization. More people, with an increasing per capita consumption, together with the exhaustion of the richer but smaller, and more

Oct 1, 1930

By G. M. J. van Heerden

Paper written on project work carried out in partial fulfilment of B. Eng (Mining Engineering) degree The Union Section of Anglo Platinum is situated ±18 km west of the town of Northam on the north-western rim of the Bushveld Igneous Complex. Both the Merensky and UG2 reefs are mined. Support of the Merensky stoping areas with rock bolts is specifically problematic due to the stoping width restrictions varying around 90 cm. The installation equipment of in-stope rock bolts and the effectiveness thereof in the Merensky stoping areas was critically evaluated. In order to do this a background research on the need for better on-the-face support had to be conducted. The need for improving the rock bolt drilling and the equipment had to be investigated and the financial implications and justifications for the improved equipment examined. To conduct the search an overall study was done on the rockfalls and safety aspects throughout the platinum industry in South Africa and specifically Union Section. It was found that most of the rock falls in the Merensky stoping areas of which ± 70% are less than 1.2 m in thickness generally occurs within 4 m from the face and causes ± 60% of the in-stope injuries. Serious shortcomings had been identified with respect to the airleg, rock drill machine and the drill steels used in the drilling of the rock bolt holes. Through experimentation, using a testing frame built for this purpose on surface and with the co-operation of mine staff and suppliers, a number of possible modifications were identified and tested. This resulted in the final product with which it was possible to drill a 1.2 m hole in the hangingwall of the stopes ranging with an angle to the hanging from 90° for a 90 cm stoping width and 67° for a 80 cm stoping width. It is confidently concluded that this system will effectively improve the total face support and result in a substantial reduction of rock falls and consequently the occurrence of injuries and fatalities in the Merensky stoping areas. The installation of rock bolts on the face with the modified drilling equipment will increase the direct support, but the system has a potential of a substantial reduction in the profile stick support density and an increase in productivity in the stoping areas due to fewer occurrences of rock falls. It was finally concluded that effective modifications to the drilling equipment for rock bolt in-hole drilling could be made and the installation thereof in the stope face is adequately justified.

Jan 1, 2002

By P. D?Elia

Following a study by NIOSH on the availability of teams in the U.S. as well as existing training sites and their capabilities, the Penn State University, leaders of the Pittsburgh Section of SME, providers of mine rescue equipment, and industry sponsors united to establish and make fully functional a student mine rescue team at Penn State University. With the growth of MERD and mine rescue competitive events at Missouri S&T, the Mine Training and Technology Center in PA, and at Colorado School of Mines Edgar Mine, a critical mass of effective training venues were made available to help student teams progress and develop mine rescue skills. The challenges to be met in creating and developing a student mine rescue team will be discussed. The rewards from this type of effort will be the quick capability of graduates from mining engineering programs to be involved in not only mining operations, but industry mine rescue teams and other leadership roles as well.

Jan 1, 2012

By W. C. Risley

IN the year 1933, workings at the No. 12 colliery, New Waterford, of the Dominion Coal Company, Limited, had advanced to a point where additional ventilation would soon be required. Furthermore, development of the mine was being .made to practically double the output of coal. Consequently, authorization was given to sink a shaft to the workings. The location selected is on the west side of the mine, about one and a half miles from the slope mouth and on the Low Point shore, some 250 feet from high-water mark. The cliff at this point is 40 feet high, with the land rising on a slope of about 5 per cent to the shaft. Figure 1 shows the location with reference to the colliery workings. The strata through which the shaft was to be sunk were pretty well known from diamond-drill borings previously made, and it was believed that water would be encountered to a depth of at least 250 feet to 300 feet. It was planned, therefore, to seal-off the water by the pumping of cement grout under high pressure. This method was considered to be the most economical means of handling the water during sinking, and would also result in a permanently dry shaft. Figure 2 shows a cross-section of the strata. The permanent shaft hoist and fan were to be electrically driven, which would necessitate the construction of a transmission line between the colliery and the shaft; therefore, it was arranged that the sinking equipment would have electric drive. As all equipment, materials used in construction, and supplies were to be hauled by truck, a roadway 1,800 feet long was required from the main highway to the site, and as heavy loads would be hauled during the fall, winter, and succeeding spring, this road was ballasted with 18 inches of clinkered material obtained from a burned culm bank one and a half miles distant. Actual field work was begun by the Company's own forces early in October. Work preparatory to sinking-in addition to the roadway and trans-mission line-included the construction of the reinforced-concrete shaft collar and fan drift connection; the permanent timber headframe (which was to be used also as the sinking headframe); the permanent reinforced-concrete building to house the shaft hoist and fan drive; and the erection of temporary buildings and installation of all equipment for sinking and lining the shaft and for cementation.

Jan 1, 1936

By G. W. Marks, A. H. Roberson

"Previous investigation 4/ has demonstrated that some of the aliphatic amines are suitable absorbents for 302, This paper reports the results of physical studies of a number of such amines with the object of determining which is most favorable as an absorbent.Monoethanol amine, diethylene triamine, and triethylene tetramine appear to be the most promising of all the amines studied, and most of this report has been devoted to studies of the physical properties of their aqueous solutions, which contain varying amounts of SO2.PURITY OF MATERIALSAll of the amines used were of commercial grade, because the primary object of this research was the investigation of a proposed works process rather than the accumulation of scientific data.The aminoethyl derivitives of ethylene diamine, namely, diethylene triamine, triethylene tetramine, and tetraethylene pentamine, only recently have been produced commercially. The chemistry of aliphatic amines is complex, and these newer derivitives have not been investigated, completely. Chemically pure material is not on the market, and since definite physical standards have not been published, one could not be assured of a pure product even if the commercial material was refined.The compilation of physical constants for the pure amines would involve much time—consuming effort without materially enhancing the value of this paper, as this work was not devoted to the development of fundamental standards."

Oct 1, 1938

By James H. Dye, N. E. Norman

There will be about 300 raise boring machines used worldwide by late 1981, attesting to the acceptance of this drilling system by the mining and construction industries. Over the past few years, many articles have cited the advantages of raise boring: •improved safety; •faster completion of the raise; •elimination of sublevels; •cost reductions; •better structural characteristics of the opening; •labor reduction; and •noise abatement. The relative importance of each advantage varies from mine to mine. When analyzing the total economics of raising, each advantage must be considered. The factors having the most effect on economics are fixed costs, direct costs, and comparative savings versus conventional methods.

Jan 3, 1981

By J. L. Perry

FOR many years, you and your fellow members of the American Institute of Mining and Metallurgical Engineers have devotedly and ably applied yourselves to the art of making iron and steel. having foremost in your minds the conservation of raw materials, suitable and efficient facilities, economical processes, and improved quality of product. For the past three strenuous years you have contributed wholeheartedly to meeting the problems of increased production. You have conducted scientific and technical investigations and research, recommended experiments. and gathered all the available and valuable information possible to gain the desired objectives. You have had many obstacles and difficulties to overcome. In the early days of your organization, there was some lack of co-operation from the industry itself-perhaps, for example, some failure to recognize the mutual advantages of free exchange of experiences and information. But regardless of any hindrances, you have made many and valuable contribution which have tended to make iron and steel manufacture leas of an art and more of a science.

Jan 1, 1944

By P. S. Sundar

A laboratory method for the simulation of in-situ leaching of uranium was developed under contract to the Interior Department's Bureau of Mines. Simulation tests using sulfuric acid, ammonium bicarbonate and sodium carbonate as reagents and hydrogen peroxide as oxidant were carried out with representative ores from Texas and Wyoming. The tests not only yielded recovery rates of uranium and permeability changes, but also qualitative inferences on the chemical and physical phenomena which occur underground. Leaching with basic solutions was found to be kinetic constrained and with acid solutions, equilibrium constrained. The rapid permeability changes observed when leach solutions were introduced, were probably caused by gas blockages in the packing. Precipitation of calcite or gypsum and the reaction of clay to leach solutions had slow and gradual effect on the packing permeabilities.

Jan 1, 1978

By H. M. Lewis

The current status of the international zinc market is summarized, and a supply /demand outlook is presented for the next five years. A number of technical problems facing the industry are outlined. Introduction ZINC has sometimes been called the unknown metal. Considering that on a world basis it ranks third among non-ferrous metals in production and consumption, zinc retains a certain modesty. It has no distinctive colour like copper, lacks the low density of aluminum or magnesium and is not always easy to identify as a product. The 'spangle' of galvanized steel is probably zinc's most distinguishing feature. The purpose of this article is to develop an over-all review of zinc. Starting with the current position of the metal, the major factors that will shape its future will be described so that an assessment of the outlook for zinc can be made.

Jan 1, 1978

A pyrite flotation concentrate assaying 0·065 oz/ton gold was investigated to determine the mode of occurrence of the gold. Ftom cyanidation and acid leaching experiments it was concluded that O· 02-0· 03 oz/ton goldwas in solid solution in pyrite and the balance of the gold was finely dispersed as grains throughout the pyrite.Autoradiography and electron-probe examination of possible areas in briquetted concentrate did not detect any grains of gold. Neutron irradiation and gamma spectrometry confirmed on 100 mg samples the fire assays obtained on 1 assay ton samples.Oxidation to hematite and reduction to magnetite at 600°C made practically the whole of the gold extractable by cyanide. This technique could be of major significance for gold ores which contain a substantial amount of "refractory" gold.

Jan 1, 1969

By D. A. Wilson

A cyclic leaching process was developed for selectively leaching and recovering cadmium from nickel-cadmium scrap battery waste. The six major steps in the process are the following: (1) washing the plates to remove KOH electrolyte, (2) roasting at 550° to 600° C to oxidize metallic cadmium and decompose cadmium and nickel salts, (3) leaching with an ammonium nitrate solution, (4) precipitation of the leached cadmium from solution as cadmium carbonate using CO2 gas, (5) removal of CO2 from the lixiviator by adjusting to pH 4.5, heating, and evacuating the system, and (6) removal of small amounts of leached nickel from the lixiviator using a solvent extraction technique. The regenerated lixiviator is then recycled to leach additional plates. Cadmium extraction was 94 percent and the cadmium carbonate product contained 0.14 percent nickel and 0.12 percent cobalt impurity. The leached plates were smelted to a high nickel-low iron alloy with no detectable amounts of cadmium.

Jan 1, 1971

The first metal-mine accident-prevention course was prepared and published in 1942-45 as a series of seven miners' circulars (Nos. 51-57). The course has been broadened in scope, revised, and brought up to date and is being published as a similar series of seven miners' circulars (Nos. 51-57, revised) on accident prevention in metal and non-metallic mines. These circulars are as follows: Injury Statistics (Miners' Circular 51), dealing with general statistics on injuries from accidents at metal and nonmetallic mines, including causes, costs, and the use of investigations and reports of all injuries.

Jan 1, 1960