Search Documents

By J. F. Pierce, S. M. Enterline

Since January 1959 a zinc refiner of novel design has been in operation at Blackwell, Okla., producing 99.995+ zinc from the output of the Blackwell horizontal retort smelter. The refiner is a continuously operated, pyro-metallurgical unit with principal dimensions horizonhl permitting one floor operation. It is very ruggedly constructed. Furthermore it is not subjected to deterioration from high concentrations of iron in the feed metal because the boiling units are separate from the rectification columns and constructed with silicon carbide brick arches through which the heat is transferred radiantly to the zinc. A zinc refiner of novel design has been in operation since January 1959 at the Blackwell, Okla. plant of the Blackwell Zinc Co., Inc., a wholly owned subsidiary of American Metal Climax, Inc. Developed by the company's technical and operating staffs, the new refiner produces special high-grade zinc (nominally 99.995+ pct Zn) from the prime western1 slab output of the Blackwell horizontal retort smelter. The refiner is a continuously operated, pyromet-allurgical, high-capacity unit employing fractional distillation to separate zinc from its impurities, consisting principally of lead, cadmium, and iron. In prime western slab, these elements may vary in concentration from 0.005 to 1.6 pct. Table I shows the impurities usually encountered in the Blackwell prime western metal fed to the refiner together with their boiling points and vapor pressures at 907oC. The commercial pyrometallurgical smelting processes for extracting zinc from ore include distillation from retorts and a limited degree of refining can be accomplished by redistillation in similar retorts. To achieve special high-grade purity, an impractical number of batch redistillations would be required, however, with an accompanying loss of much metal. A continuously operated and integrated unit is required in which fractional vaporization and condensation can take place in a large number of stages. The first commercial continuously operated unit was developed by the New Jersey Zinc Co.4 In the separation of any two substances the degree of separation is limited if a mixture exists having a constant boiling point. The Zn-cd5 and Zn-pb6 systems contain no constant boiling points and hence these metals may be separated to any degree of purity. Basically, the pyrometallurgical refining of zinc involves three steps: a) iron, copper, and other metals having no appreciable vapor pressures at 907ºC concentrate in the bath when the impure zinc is boiled, b) lead, bismuth, antimony, and other metals having boiling points above but closer to that of zinc are selectively condensed from the vapor boiled from the bath, and c) cadmium and other metals having lower boiling points than zinc are fractionally distilled by reboiling and subsequent condensation of the zinc from the vapor. The boiling and condensation of zinc must be conducted in vessels constructed of materials which are refractory at the temperature involved (907 ºC) and it is highly desirable that they also be resistant to attack by the various metals. This requirement dictates construction from relatively small, simply shaped pieces which limits the pressures which may be employed to avoid leakage through the numerous joints. Stresses induced must be limited essentially to compressive ones and suitable provision must be made to permit thermal expansion of the components in order to minimize these stresses. Where heat is to be added for boiling or removed for condensation, refractory material through which the heat flows must have a high thermal conductivity. Silicon carbide is highly conductive but is subject to attack by iron and is expensive compared to other commonly employed refractories. A hard, dense aluminous fireclay is well suited to contain these metals where high thermal conductivity is not required. Zinc will penetrate the pores of fireclay brick but only to a limited depth in an exterior wall and has little effect other than an increase in weight and conductivity. The design objectives of the Amax refiner were: a) to achieve a long life by heavy, rugged construction and by employing silicon carbide refractories only where required for heat conductivity and not in contact with liquids of high iron concentrations, b) to simplify operation, manning and control by essentially horizontal construction, and c) to obtain high capacity in a single unit. DESCRIPTION Flow of metal through the Amax refiner is shown diagrammatically in Fig. 1 and schematically in Fig. 2.

Jan 1, 1963

By G. W. Healy, L. F. Sander

was investigated by reacting thin discs of calcium oxide with gas mixtures of CO2, CO, and Son. Its value was 19,300 * 300 cal independent of temperature in this range. No solid solubility of sulfur in calcium oxide was detected within the limits of the experimental method and it is estimated to be below 0.025 pct by weight. The importance of lime in desulfurization is well-established but complete information on the pure phase equilibrium: CaO + 1/2 s2 = CaS + +02 [11 is not yet available. The goal of this work was to evaluate solid solubility of CaS in CaO and to determine the free-energy change associated with Reaction [I] at temperatures of 1400" to 1650°C. The equilibrium constant for Reaction [1] can be written: It is convenient to rewrite Eq. [2] in the form: where A = {Ps /PqJ1'2 has been referred to' as the "sulfurizing power' of a gas mixture. In this work, thin discs of CaO were suspended in a vertical tube furnace and exposed to CO + CO2 + SOz gas mixtures having known values of A. The samples were then analyzed for sulfur. As expected, X-ray diffraction confirmed that CaS was the only sulfur-bearing phase formed at the relatively low oxygen pressures used. EXPERIMENTAL PROCEDURE Reagent-grade CaCO3 was pressed in a 3/8-in.-diam pill die and prefired in air to produce CaO discs weighing between 0.004 and 0.01 g. Several discs were used to provide a suitable weight for chemical analysis while maintaining a large surface area to react with gas mixtures. These were placed in a platinum mesh basket and suspended in the gas stream in the hot zone of a vertical tube furnace. Desired gas mixtures were prepared from cp grade CO and CO2 and anhydrous grade SO2. The method of soap bubble displacement was used to calibrate capillary flow meters. While this gave excellent results with CO and Con, some problems with bubble insta- bility and soap film "drag" arose with the use of SO2 at low flow rates. Hence, frequent sampling and analysis of gas mixtures was carried out to insure proper control of the ingoing SOZ. The furnace used for gas:solid equilibration was a vertical mullite tube externally wound with 60 pct Pt-40 pct Rh wire having a diameter of 0.028 in. An inner tube of $ in. ID served as the reaction chamber having Pyrex ground joints sealed to the mullite to provide gas-tight connections at top and bottom. A Pt-Pt 10 pct Rh thermocouple was inserted into a protection tube adjacent to the sample basket to measure sample temperature during a run. Constant-temperature control to 2C was observed at any desired set point within the range of this investigation. This was accomplished by a control thermocouple imbedded in the furnace windings which served to actuate an electronic controller wired for high-low operation. The sulfur analyses of the solid samples were carried out using a stoichiometric combustion technique based on the method of Fincham and Richardson. Some analyses were done using a modified evolution method3 but these were used primarily to check the results of the combustion method. The results were in good agreement but the combustion technique of-ferred an advantage in economy of time and material. CALCULATION OF GAS EQUILIBRIA Heating a given mixture of CO + CO + SO2 to high temperatures gives rise to a large number of product species. The details of calculating the partial pressures of these products of interaction and dissociation can be found in several references4,5 and need not be repeated here. The thermodynamic data selected for the major species in the gas mixtures are shown in Table I. Equilibrium constants from these reactions were combined with oxygen, carbon, and sulfur balances and a computer program written to facilitate the calculations. Some early difficulties in reproducing experimental results were finally traced to the effect of atmospheric pressure changes. No reference to consideration of this question had been found in the

Jan 1, 1969

By Laurance S. Reid, Joe A. Porter

Gas dehydration plays an important part in the production of natural gas. Effective dehydration prevents formation of gas hydrates and the accumulation of water in transmission Systems,2,6,7 insuring uninterrupted gas deliveries at maximum efficiency under the most adverse weather conditions. At the present time, most gas companies require a maximum water vapor content of seven lb per million standard cu ft of gas. so that virtually all gas tendered for sale must he dehydrated to meet this specification. For a number of years it has been common practice to produce gas and gather it at a common point for dehydration prior to discharge into the transmission system.1,3,11,16,17 However, higher transmission line pressures, long gathering lines and relatively low ground temperatures have made it necessary to dehydrate gas at. or near. individual. wells in order to gather gas from a number of newly developed fields without unusual difficulty. Where gas has been dehydrated at pressures ranging from 300 to 800 psi in the past. future trends indicate that these processes may be operated at pressures as high as 2,000 psi. Economics of gas dehydration are of great importance, partitularly where facilities must he provided to process relatively small quantities of gas, such as the production from an individual well. Although the adsorption of water vapor from gas on a granular sorbent material such as activated bauxite, activated alumina, or one of the alumina-silica gels is highly effective and produces virtually "bone dry" gas, the cost of a small unit of this type is substantially greater than that of an absorption process which, through proper selection of the absorbing liquid, will dehydrate the gas sufficiently to meet pipe line specifications. For this reason, a great deal of emphacis has been placed on the development of small, inexpensive dehydration units8,24 and the search for more effective absorb. ent liquids has been intensified. A wide variety of methods for dehydrating gas are known' and many of these have been used in industry. Earlier applications of the absorption process employed concentrated solutions of calcium and lithium chlorides as the absorbent. The severe corrosion problems inherent in handling these solutions and the relatively small dew point depressions obtained caused early abandonment in favor of, or conversion to. diethylene glycol when it was found that aqueous solutions of this organic liquid were more hygroscopic than the brines and were non-corrosive. Processes employing diethylene glycol-water solutions are widely used for gas dehydration at pressures ranging as high as 1,200 psi.13,14,15 At nominal pressures a dew point depression of 45° to 50°F may be be and the data of Russell et al." indicate that a minimum dew point is obtained from the effluent gas at a pressure of approximately 1,200 psi when the gas is in equilibrium contact with a 95 per cent by weight diethylene glycol solution. In a number of instances the dew point depression obtained with diethylene glycol-water solutions is not sufficient to produce a specification product without cooling the inlet gas. In a recent search for a better absorhent, triethylene glycol was used in a small commercial dehydration unit and subjected to rather exhaustive field tests.' The data obtained were encouraging and indicated that, at pressures ranging from 300 to 500 psi, triethylene glycol porduced a substantially greater dew point depression than diethylene glycol. These results led to an investigation of the system natural gas-water-triethylene glycol in an effort to obtain vapor-liquid equilibrium data, to determine pressure limitations, and to develop other data pertinent to the design of gas dehydration processes. A review of the literature has failed to reveal any data which permit reasonably accurate calculation of the vapor-liquid equilibrium conditions for a solution of water and triethylene glycol in contact with natural gas at high pressure. Since these constituents form a non-ideal system, the Poynting equation18,21 or the usual combination of Raoult's and Dalton's laws19,20,22 would not be valid. Correction of Raoult's and Dalton's laws by the use of activity coefficients2' is not feasible for available data are insufficient for the prediction of the actual increase in the ratio of the activity of one component in the vapor phase to its activity in the liquid. Therefore. experi-

Jan 1, 1950

By O. P. Arora, M. Metzger, G. R. Ramagopal

The rates of grain boundary and general corrosion were surveyed by an approximate method. Quantitative differences between their variations with the strength or cupric ion content of the acid yielded large variations in their ratio, highly selective intergranular attack being observed only under specific chemical conditions. The boundary corrosion rate increased with the copper content of the aluminum; this was attributed to an autocatalytic effect similar to the one shown for general corrosion. High- purity aluminum in hydrochloric acid exhibits striking intergranular corrosion and other structure-dependent corrosion phenomena of fundamental interest. The behavior is highly sensitive to the metallurgical and chemical conditions, the significance of many of which has not been established. The features of the intergranular-corrosion phenomenon, first described by Rohrman,l are summarized in the remainder of this paragraph. Strong attack normally occurs only at high-angle grain boundaries.' Usually 15 to 25 pctHCl is used to obtain a high rate, but this has also been obtained with weaker (7 to 15 pct) acid either by adding cupric or ferric ion to the acid3-5 or by passing an anodic current (-0.1 ma per sq cm).2,3,5,6 The two latter corrosion conditions produce strong attack of low-angle boundaries after certain heat treatments 2-4,5,7 The susceptibility of high-angle boundaries is influenced by the grain-boundary segregation of iron atoms; this increases the slow (µ per month) attack in 10 pct HCl8 but diminishes the rapid (mm per month) attack in 20 pct Hc14 (the present and most previous investigations deal with rapid attack). That segregation of elements other than iron affects intergranular corrosion has not been demonstrated, although analysis of data for iron alloys indicated that at least one other element must be considered.9 Intergranular attack occurs over a wide range of purity although it begins to become obscured above several hundred parts per million (ppm) total im- purities by the severe general corrosion which accompanies the higher iron contents and which is associated with the presence of a second phase or an inhomogeneous distribution of the dissolved iron.4,6,10 The variation of intergranular-corrosion rate with heat treatment1'3-6'"10 can be explained in some cases in terms of the distribution of the iron impurity but is not in general adequately understood. The present work dealt with two questions not previously considered in detail. The first proceeded from the view that the extent to which a special behavior is associated with the boundaries is indicated not by the intergranular corrosion rate alone but by the ratio of the intergranular to the general corrosion rate. A comparison of the two rates was therefore made for one lot of aluminum in acids of varying strength and metallic ion content. The second question was the effect of the copper content of the aluminum. For general corrosion, it has long been known that copper ions introduced into the acid by corrosion of the solid solution are reduced on the aluminum as patches of elemental copper which enhance the corrosion rate by providing cathodes of lower hydrogen overvoltage than were originally present.''-'3 Since the copper patches remain themselves unchanged, their action is "catalytic", and since they are products of corrosion, the effect is "autocatalytic." This phenomenon is significant at copper levels much lower than previously suspected, even at those typical of high-purity aluminum, as the authors have shown in a previous paper.l4 The present work shows that copper content affects intergranular corrosion. With polycrystalline specimens, truly quantitative rate measurernents are not readily made for intergranular corrosion or for general corrosion in the presence of rapid intergranular attack, and previous work in this field has tended to be qualitative. The present study made use of a simple procedure which provided fair approximations to the quantitative corrosion rates and fitted the purpose of surveying the behavior over % wide range of conditions and displaying certain large effects. The approximations involved in this work were usually outweighed by the experimental scatter, which tends to be substantial in a system as sensitive as this one. I) EXPERIMENTAL A. Material. The material procured, Table I, represented three low copper (1 to 3 ppm) lots, two of "normal" copper content (21 and 22 ppm), and two

Jan 1, 1962

By William Y. Holland, Roger M. Cook

In view of the increasingly widespread deterioration of concrete structures as the result of the interaction of the alkalies sodium and potassium released by hydration of portland cement and susceptible rocks and minerals in aggregates, it is believed that a paper summarizing the geographic distribution of these aggregates will be of interest to producers and users of concrete, concrete products, and concrete-making materials. THIS paper reviews the problem of alkali-aggre-gate reaction in concrete and describes the geologic and geographic occurrence and distribution of alkali-reactive sand and gravel in western United States. It includes no discussion of crushed stone or synthetic aggregates. Most deposits of sand and gravel are accumulations of particles of rocks and minerals from a variety of sources, and it is not unusual for at least one or two varieties of the rocks to contain some form of reactive material. Examination by petro-graphic methods of many sands and gravels, as well as manufactured aggregates, has shown that a comparatively high proportion of the deposits does contain, in greater or lesser degree, rocks and minerals known to be deleteriously reactive with the alkalies of cement. Fortunately the amount of reactive materials is commonly less than that necessary to cause deleterious effects in concrete. As investigation of unsound concrete structures progresses, it becomes evident that the alkali-aggre-gate reaction is even more widespread than supposed, Figs. 1 and 2. Even though some parts of the country appear at present to be immune, further investigations will probably show that the effects of alkali-aggregate reaction can be seen in many structures in these areas, although only on a small scale in most of them. Many concrete structures will, of course, have lived their useful life before disintegration from this cause is serious, and in others the alkali-aggregate reaction may never become significant even though the microscopic evidence of reaction is present. The alkali-aggregate reaction first was reported to be a cause of deterioration of concrete in 1940 when Stanton1 described expansion of concrete pavements in California. Similar expansion and deterioration of concrete was recognized during succeeding years in concrete structures located in many parts of the country, but particularly in the western states. A number of concrete laboratories2 became interested in the problem. It was soon determined that only certain combinations of aggregate and cement caused the alkali-aggregate reaction to take place, and moreover that the reaction progresses only in the presence of water. Further research proved that cements containing more than 0.60 pct total alkalies (pct Na,O + 0.658 x pct K2O), when used with aggregates containing appreciable amounts of reactive ingredients, caused the reaction to take place, usually with subsequent deterioration of the concrete. During the last few years this limitation has been adhered to in both government and private construction as the maximum allowable alkali content of cement to be used with aggregates of known alkali reactivity. Because of this limitation, it appears that deleterious reaction either has been reduced or eliminated in many recently built structures in which it probably would otherwise have occurred. Recent tests have shown that the degree of expansion obtained with any particular cement-aggre-gate combination depends not only on the alkali content of the cement but also upon the relation of this alkali content to the amount and degree of reactivity of reactive constituents in the aggregate.' In laboratory mortar bars, opal and cements with alkali content of as low as 0.2 pct (as equivalent of Na2O) have produced deleterious expansion as the result of alkali-aggregate reaction. These experiments demonstrate that aggregates containing even 0.1 pct of opal are deleteriously reactive. It was soon determined that alkali-silica gels were formed by the interaction of the alkalies of the cement and the reactive aggregate, Figs. 3 and 4. Osmotic or swelling pressures produced by the continued hydration of these gels cause expansion of the concrete with resulting cracking, warping, and dislocation. Evidence of the alkali-aggregate reaction can be seen by a petrographic study of the deteriorated concrete. Among the first structures studied by this method was Parker Dam on the Colorado River, California-Arizona. In the concrete from this dam pebbles of rhyolite, andesite, siliceous limestone, and chalcedonic chert were found to be reactive.

Jan 1, 1954

By R. L. Perrine

A stability theory is developed for miscible liquid-liquid displacement within a porous medium. In the usual case considered, a high-density high-viscosity "oil" is displaced downdip by a low-density low-viscosity "solvent'! Perturbation methods are used to find the conditions under which the spreading mechanism changes from the stable dispersion process to unstable viscous fingering. We find that instability is conditional, that there is a dependence on the shape of a disturbance leading to a"diameter" effect and that very difficult experimental scaling problems may result. A useful consequence is the definition of a minimum "slug size" for stable miscible displacement. This should make possible optimum use of the solvent process for oil recovery. The results may apply to many situations in which one fluid displaces another of somewhat different fluid properties within a porous medium. INTRODUCTION The process of miscible liquid-liquid displacement looked very favorable when it first received serious consideration as a means to increase petroleum recovery. Some early laboratory results were interpreted to mean that only a small "slug" of solvent was needed, perhaps 2 to 3 per cent of a hydrocarbon pore volume. This "slug" could recover the oil in an entire reservoir provided the fluids remained miscible.1,2 Only a slow growth of the "mixing zone", or gradual transition from oil to solvent, should occur. This would follow naturally from mixing by a dispersion mechanism such as that described by Scheidegger.3 And, indeed, laboratory cores have shown this kind of behavior provided solvent viscosity was at least as great as that of the oi1.2,4-6 The same kind of behavior has also been observed with solvent viscosity lower than that of the oil after the distance traversed became large. Not all laboratory results have been this favorable, however.7-9 Mixing zone growth may become proportional to the distance traveled rather than the square root of this quantity. Such behavior accompanies high rates in short systems of large diameter, provided the viscosity ratio is adverse. If this more rapid spreading were to persist in a reservoir, the solvent requirement for miscible "slug" displacement could exceed 30 per cent of a pore volume. There is considerable economic importance in the difference between 3 and 30 per cent solvent. A 1ogical conclusion is that two different kinds of flow behavior are possible, with each kind leading to a different result. One kind gives efficient displacement, the other does not. In the efficient case, the solvent bank spreads out only by the mechanism we have termed dispersion. Under these conditions, displacement is as near piston-like as possible. In the second kind of flow, found only with adverse viscosity ratios, viscous fingering occurs. That is, permeability variations cause a small finger of low-viscosity solvent-rich fluid to move ahead of its average position within the mixing zone. This creates a path of low resistance to flow, and an even greater amount of solvent-rich fluid follows. Thus, the process is autocatalytic. Once started, the fingering mechanism rapidly becomes dominant. The question to be answered is this. Under what conditions will each of these two different kinds of flow occur? In particular, what conditions denote the transition from dispersion to viscous fingering as the solvent spreading mechanism? The answer may tell us whether or not the desirable, near piston-like miscible displacement process is practical. An answer to this problem can be obtained from theory by the use of perturbation methods. The procedure is as follows. We first formulate a mathematical representation of the system. Then a small disturbance (or perturbation) in solvent concentration profile is introduced and observed to see what happens. Unstable flow is indicated when a small disturbance will grow larger. This will lead to eventual viscous fingering. If on the other hand the disturbance dies out, the displacement is stable. In this latter case, with dispersion as the spreading mechanism, near piston-like displacement is possible. Thus, this paper presents the development of a stability theory for miscible liquid-liquid displace-

By N. K. Chen, R. B. Pond

IN the study of slip band* formation, there have been many examples to show that they do not always appear as lines traversing the entire crystal, but as segments whose ends seem to vanish in their path through the crystal. This characteristic appearance of slip bands has been witnessed under the optical microscope at various magnifications'-' and also under the electron microscope.' A typical example of this behavior seen with the optical microscope is shown in Fig. 1. However, the slip band studies were generally conducted on polished surfaces of single or poly-crystalline metals which had been previously deformed; i.e., the load was generally released so that the observation could be made. Any picture of slip bands so obtained can represent the surface phenomenon only in a static state of the strained material. The conditions prior to their formation cannot be definitely and clearly assigned. Thus, while a segmented slip band may suggest that slip is a growth process as supposed by the theory of the nucleation of slip,V he usual appearance of suddenly and fully developed slip bands around the crystal has generally been considered as a consequence of uniform shear of the entire slip plane akin to a cataclysmic process. Little clear-cut information is available with regard to the speed at which a slip band forms, its direction of motion, the geometry of its position with regard to its neighbors, and its dependence on orientation. A description is given in this paper of experimental apparatus by which the progressive formation of slip bands can be recorded while the specimen is undergoing deformation. Qualitative and quantitative data on the dynamic formation of slip bands will be presented with special interest concerning the propagation of slip bands, the spacing of slip bands, and their relations to strain hardening. Views on the formation of slip bands are discussed and a mechanism of the unit process involved in the formation of a slip band is proposed. Preparation of Specimens Single-crystal specimens of high purity aluminum (99.997 pct), 1/8 in. square in cross-section and 1% in. long in gage length, were made by the method of gradual solidification from the liquid state. Since no machining work could be introduced in preparation of crystals of such small size, a special mold was designed for casting them to final shape. The mold consisted of two, separate, high purity graphite blocks. Generally, 20 molds were packed together in one container so that 20 specimens could be obtained by one casting operation. This was desirable since it was possible by this method to obtain groups of crystals with similar orientations. The as-cast crystals were carefully clipped from the gate, etched, and homogenized for 24 hr at 600°C. They were then very gently polished using a 4/0 paper, re-etched, and finally electrolytically polished after the method previously described by Chen and Mathewson.6 The crystallographic orientations were determined using a back-reflection, Laue method. Tensile Testing and Photographic Method The tensile testing equipment for these tests was composed of a specially designed microtensile machine, microload cell and microclip gage with necessary appurtenances. The members of the microtensile machine consisted of three parts, as shown in Fig. 2. The chassis is equipped with an oil cylinder, A, and piston, the piston being part of the movable cross-head, B. Pressure in the oil cylinder is controlled and regulated by an external pneumatic-hydraulic cell, C, which is connected to the cylinder by a Vs in. high pressure copper tube. This cell is half filled with hydraulic oil and has a needle valve, D, on the oil exit side as well as a needle valve, E, on the gas inlet side. A quick-acting valve, F, as well as a pressure gage is provided for the gas side. The oil exits into the load piston on the microtensile machine. By connecting a tank of inert gas to the gas inlet, regulated pressures were provided over the oil so that the oil would leave the cell at a rate determined by the setting of the exit needle valve, the gas pressure, and the pressure of the oil in the load piston of the microtensile machine. With this pneumatic-hydraulic appurtenance it was possible to

Jan 1, 1953

By Josiah Royce

To evaluate chemically the sample of rock obtained by diamond drilling, it has long been recognized that the analyses of the two components of the sample, core and sludge, must be given appropriate influence in computing the average analysis of any unit of depth. The purpose of this investigation is to set forth what means are available for apportioning the effect of core and sludge on the final analysis, what variables affect the problem, and what combination of applied mathematics will closest approximate the truth under each condition as these variables proceed within their limitations. A drill hole is bored in iron ore exploration principally to test variations in rock composition with depth and is usually directed as nearly normal to the bedding of a horizon to be tested as possible. This practice has a tendency to minimize variation in composition laterally which in any event is not likely to be great. It is obvious that the opportunity for change in analysis of a particular rock is not statistically as great radially in a diamond drill hole where the distance in which such a change may occur is from 0.719 in. (EX bit) to 1.469 in. (NX bit) as there would be longitudinally even in a' run as short as 5 ft. Variations in composition of bedded or layered rocks are usually greater normal to the bedding than parallel thereto. Even in massive rocks, like porphyries, variations are functions of distance. Hence. in either case, variations along the hole are of greater effect than across it. Let us examine Fig 1 briefly to observe a cross section of a unit of depth of a typical diamond drill hole. If we neglect radial change in chemical composition, which we have seen is small compared to lengthwise variation, we can see that if core recovery was 100 pct, the core and its surrounding area, which would be recovered as cuttings (assuming 100 pct sludge recovery), must analyze the same if the sampling is perfect. This is the foundation of this paper, namely, that if core recovery is complete we may assume that the core constitutes as nearly as possible a perfect sample of the ground drilled. Now let us pass to the methods of weighting core and sludge in the final analysis and then develop each in turn. One might employ core analyses only, sludge analyses only, or apportion the influence of each by one of several methods. The most common apportionment is by direct proportion to relative theoretical vol- ' ume occupied by each component in the cylinder hollowed out by the drill, known as the Longyear formula. Another logical treatment would be to consider core and sludge in the final analysis according to the weight of each recovered. This procedure was elaborately set forth and refined by R. S. Moeh1man.l Then to be sure that we have embraced all the possibilities, we must admit that some other method or methods may be devised empirically or by mathematical maneuvers. Should a drill machine be capable of recovering 100 pct of the core in all types of rock, certainly core alone need be analyzed and no complicated mathematics are required; but although some companies have had fair success in obtaining high percentages of core in certain homogeneous ores on the Mar-quette Range, their same methods have proved disappointing on the Menominee, Cuyuna, and Gogebic Ranges where the iron formation often varies widely from flinty chert beds interstratified with soft hematite to wholly leached ore material composed of an unpredictable mixture of hematite and limonite with occasional zones of sugary, recrystallized chert. In spite of numerous mechanical improvements in core barrels, few drilling programs can count on complete core recovery. The sludge alone might be analyzed but for practical reasons this is inadvisable when core is obtained due to the numerous opportunities for contaminating or losing portions of the cuttings. The Longyear formula involves a weighting of the core and sludge in proportion to the theoretical volume of each, that is, where the volume of the core recovered is one-third of the total cubic volume of the cylindrical hole made by the drill, the analysis of the core is given one-third of the weight in the final analysis. This approach to

Jan 1, 1950

By C. W. Allen, B. D. Cullity

The proportional limit of iron crystals in torsion is governed by the resolved shear stress in the most highly stressed slip systems, averaged around the specimen circumference, and does not obey a critical resolved shear stress law. Crystals of most orientations exhibit a stage of easy plastic deformation, akin to easy glide in tensile or shear specimens. Transient deformation, similar to that which occurs in single crystals of other materials, is also observed. THE torsional deformation of single crystals of magnesium (hcp) and aluminum (fcc) has been described recently by Choi et al.,&apos; especially with respect to the criterion for the orientation dependence of the onset of plastic flow in these materials. The purpose of this paper is to present results of torsion tests of iron single crystals and thus to extend this yield criterion to a bcc metal. In addition to considering the variation of proportional limit with crystal orientation, this paper also briefly treats work hardening, transient deformation, and the mechanism of plastic flow in iron. The effects of the method of surface polishing and the chemical purity of the iron have been investigated. STRESS DISTRIBUTION It is convenient to express the stress at any point of a cylindrical crystal stressed in torsion in terms of t0, which is the shear stress acting at the surface on a plane normal to the axis of the cylinder and in a direction tangential to the cylinder. This stress is given by To = 2T/pr3 [1] where T is the applied torque and r the specimen radius. The shear stress t, resolved in any chosen slip system is given in terms of 7, by1 Ts/TO = sin 0, cos d sin (0, -) + cos , sin d sin d - ) [2] where 0 and d are the angles between the specimen axis and the slip plane normal and slip direction, respectively; h is the angular circumferential position on the specimen at which t, is being determined, measured from an arbitrary reference plane which includes the axis;o and d are the angular coordinates of the projections of the slip plane normal and slip direction on a transverse section with respect to this same reference plane. Slip in iron occurs in a <1ll> direction on the {ll0}, (1121, and (123) planes, which together comprise 48 slip systems. A complete evaluation of the stress distribution in an iron crystal stressed in torsion would therefore require a calculation of Ts/T0 as a function of for 48 different slip systems. Fortunately Gough,&apos;who studied the behavior of iron crystals in alternating torsion, was able to simplify this problem considerably. He showed that it was sufficient to consider a kind of average slip plane for each slip direction, namely the mathematical plane of maximum resolved shear stress containing the slip direction considered. This simplifying approximation is possible because, for each slip direction, the active slip plane or planes lie very near this mathematical plane of maximum shear stress. Vogel and rick&apos; have critically reviewed the early work of Taylor and Elam,13 Taylor,14 and Fahrenhorst and schmid8 from which the identification of the above crystallographic planes as slip planes in the bcc lattice largely stems. While their criticism is clearly justified, their own results do little to clarify the issue. The role of cross slip (screw dislocations changing glide planes) is evidently so important in this case, as Read3 has suggested, that methods for deducing slip systems from observations of gross slip traces are inadequate, such traces commonly arising from complex dislocation motion. Thus the treatment given here involving the plane of maximum resolved shear stress seems a logical simplification especially in view of Gough&apos;s2 study of a iron. There is, however, an assumption built into the subsequent treatment the comparative validity of which is difficult to assess, namely, that slip in all slip systems in iron may be characterized by a common critical resolved shear stress. The shear stress 7, resolved in a slip direction defined by d andd, and on the plane of maximum shear stress containing this direction, is found by first maximizing 7s/70 with respect to either Oo or 4,. The slip plane coordinates are then eliminated by using the relation between 0, ,o and d, d, namely,

Jan 1, 1963

By T. P. Floridis, J. H. Young

The need for close control of the phosphorus content of steels has led to numerous investigations on the equilibria of the dephosphorization reactions. Winkler and chipman1 have established the general conditions for effective dephosphorization of steel. They are high slag basicity, high oxygen potential, and low temperature. Other investigators have made additional contributions to the understanding of the dephosphorization process. The current status of the understanding of the dephosphorization of steel is concisely presented by Bodsworth2 and by Ward. The investigation reported in this communication was undertaken with the purpose of establishing the effect of additions of barium oxide and calcium fluoride on the dephosphorizing capacity of slags. Esin and Gel&apos;d4 proposed that barium oxide, being more basic than calcium oxide, should cause an increase in dephosphorizing capacity when added to steelmaking slags, or when used as a substitute for calcium oxide. Derge5 has also proposed that in the future conventional slags might be replaced by BaO-Al2O3 slags. There is, however, no experimental evidence confirming the effect of barium oxide on the dephosphorizing capacity of slags. The effect of calcium fluoride on the dephosphorization of steel is not clearly understood. It is generally recognized that additions of calcium fluoride are beneficial. It is not clear, however, whether calcium fluoride affects the equilibrium of the dephosphorization reaction, or whether it simply causes an increase in the fluidity of the slag and, consequently, faster approach to equilibrium. The experimental procedure consisted in equilibrating synthetic molten slags with liquid copper at 1550°C under a gas stream containing argon, hydrogen, and water vapor. In all experiments the argon to hydrogen ratio was approximately 4:1, and the hydrogen to water ratio was 5.42:l. Molybdenum crucibles were used as containers for the slag and metal. Under the above-described conditions of temperature and composition of atmosphere, there was no observable attack of the crucibles by the metal, slag, or atmosphere. Copper was used instead of iron, because iron attacks molybdenum. The equilibration was made in a tubular furnace consisting of a recrystallized alumina tube. The alumina tube was heated by electrical resistance. A Pt-40 pct Rh wire winding was used for most runs. A silicon carbide tubular resistor was also used for some runs. Temperatures were measured with a Pt-Pt-Rh (10 pct Rh) thermocouple and kept constant within ±5°C. Equilibrium was approached from both sides, i.e., by adding the phosphorus either as oxide in the slag or as a phosphorus-rich alloy of phosphorus and copper. The holding time at the equilibrium temperature was 6 hr. At the end of each run the crucibles were rapidly cooled and removed from the furnace. The slag and metal were separated and analyzed. The experimental results are shown in Table I. The phosphorus content of the slag is expressed both as percent phosphorus pentoxide and as percent phosphorus. The basicity ratio is computed by dividing the number of moles of basic oxides-oxides of barium, calcium, magnesium, and sodium—by the number of moles of acidic oxides- oxides of aluminum, phosphorus, and silicon. Calcium fluoride is not included in the computation of the basicity ratio; i.e., calcium fluoride is assumed to be neither basic nor acidic. The distribution ratio of phosphorus—percentage of phosphorus in the slag divided by the percentage of phosphorus in the metal- is plotted in Fig. 1 against the basicity ratio. The results indicate that slags containing barium oxide have greater dephosphorizing capacity than slags containing calcium oxide. The high dephosphorizing capacity of slags containing sodium oxide and the low dephosphorizing capacity of magnesia-containing slags which already have been reported in the literature2 are confirmed by the results of this investigation. It appears that calcium fluoride has a beneficial effect on the distribution of phosphorus between slag and metal in acid slags only. Although the obtained distribution ratios between the phosphorus contents of slag and copper are not directly applicable to the dephosphorization of steel, they are sufficient for evaluating the effect of slag additions on the dephosphorizing capacity of slags in general. An increase in the ratio of distribution of phosphorus between slag and metal indicates lowering

Jan 1, 1968

By Joseph C. Mead, Alan Stanley

The MacIntyre Development of the National Lead Co. is located at Tahawus, N. Y. The operations involve the mining and concentrating of a titaniferous iron ore to produce an ilmenite concentrate and a magnetite concentrate. Construction of the MacIntyre plant was commenced during the summer of 1941,when world conditions threatened to cut off the supply of Indian ilmenite. An open pit mining operation was developed and the crushing and milling equipment put in operation in July 1942. A general description of the operation was given in the Adirondack Issue of Mining and Metallurgy for November 1943. The metallurgy of the mill operation was described by Mr. Frank R. Milliken,* Plant Manager, National Lead Company, MacIntyre Development, and presented at the AIME New York Meeting, February 1948. The magnetite concentrate produced in the milling operation was too fine (minus 20 mesh) to be used directly in iron blast furnace operation, and most of the magnetite had to be stockpiled in 1942 and 1943. In 1943, the Defense Plant Corp. built a Greenawalt sintering plant at Tahawus, N. Y., to put the magnetite concentrate in a more suitable form for use in the iron blast furnace. The Greenawalt sintering plant consists of three 10 by 25 ft sintering pans designed to produce 1800 gross tons of sinter per 24 hr. The vacuum to each pan is produced by two Greenawalt fans in series, pulling approximately 30,000 cu ft of air per minute at 50 in. water gauge vacuum. The plant started operation in August 1944. The present plant production averages 25 tons per operating pan hour (approximately 224 lb per operating hour per square foot of grate area) of plus 1 in. sinter. Raw feed to the plant consists of 61 pct magnetite, 4 pct anthracite coal culm, and 35 pct minus 1 in. return fines which are conveyed to a pug mill where the materials are mixed thoroughly and water added to give the mixture 5.5 to 6 pct moisture. The mixed prepared feed is conveyed to two 4 by 10 ft vibrating screens where the minus 1 in. plus 5/8 in. return fines are screened out and discharged into a surge bin for use as a hearth layer. The minus 5/8 in. prepared feed is discharged into another surge bin for use as prepared feed. A charge car, electrically operated, having a capacity of one charge of prepared feed and several charges of hearth layer, lays a thin layer of plus 5/8 in. return fines and 9½ in. depth of prepared feed into the pans. A fluffing roll and a vibrator on the car fluffs and spreads the prepared feed into the pans. An ignition car, electrically operated, ignites the top of the bed with a 30 sec flash burn. The 9½ in. bed sin-ters in approximately 13 min. Dumping the pan, and recharging and igniting the bed requires 2 min. To improve the quality of the ilmenite concentrate produced in the mill and to reduce the amount of titanium dioxide lost in the mill tailings and in the magnetite product, extensive research work and pilot plant operations have been done on grinding the crude ore to minus 65 mesh size (rather than to minus 20 mesh) and concentrating it by a combination of magnetic separation (for magnetite recovery) and flotation (for ilmenite re-covery). These tests have proved successful in increasing ilmenite re-covery and grade. With the development of the ilmenite flotation process to a stage where a full scale flotation plant was in the design stage, the problem arose of handling the 65 mesh magnetite concentrate that would be produced. In order to study and solve the problems of handling and sintering the 65 mesh magnetite in the sinter plant, a pilot sinter plant was secured from John E. Greenawalt. The effect of using 65 mesh magnetite in the sintering operations was then studied on the 2.4 sq ft test pan, operating under conditions as similar to the large plant as could be set up in the laboratory. A series of tests were run in the test pan on present sinter plant feed that had been mixed in the plant pug mill. An average production and an average quality of sinter produced in this series

Jan 1, 1950

By R. H. Olds, B. H. Sage

The transient flow of gases in long pipe lines is a problem of industrial interest. The present discussion deals with the application of the conservation of momentum and material to the transient flow of gas in conduits which are long with respect to their diameter. Solutions of the resulting equations include consideration of variations in friction and specific volume of the fluid as functions of time and position along the conduit. The changes in state along the pipe line are established as a function of time. The methods proposed may be extended to other situations. The flow of compressible fluids under steady conditions&apos; has been considered in detail. Primary emphasis was placed on the development of simple means of taking into account the non-uniform flow&apos; realized in long conduits under such conditions. Binder2 discussed the essential differences between the flow of compressible and uoncompressible fluids. Bonilla" proposed direct methods of solution for equations describing isothermal flow in long pipes. Similar considerations limited to steady flow have been discussed by Ruth.&apos; Palsgrove 5 sugrested a graphical means of solving specific problems relating to the flow of gases in conduits of uniform section. Some of the basic concepts of the flow of a compressible viscous fluid in straight tubes have been described by Kuo.6 Problems of this type require knowledge of the equation of state of the fluid. In many cases it liar been convenient to assume that the fluid follows the relationship ascribed to a perfect gas. The treatment of unsteady flow of compressible fluids is less complete. This state of affairs result* from the fact that the differential equations relating pressure and flow rate with time and position for unsteady flow are nonlinear in character.&apos; Muskat and Wyckoff presented an excellent treatment of the situation in laminar Bow where inertia forces were not of controlling importance. Somewhat earlier Hurst9 discussed the uncteady flow of fluids in petroleum reservoirs. Helhering-ton. MarRoberts. and Huntington&apos;" established experimentally the pressure distribution and accumulative flow rate of natural gas through an unconsolidated sand. Recently Joffe11,12 conhitlcretl the specific problem of the flow of natural gas in relatively long.,. pipe lines for unsteady conditions with emphasis upon the economic feusibility of the storage of gas in such a reservoir. These discussions were based upon approximations of the partial differential equations applying to the condititons of flow. The results were descriptive of the physical situation and indirated the effertiveness of large pipe lines as cyclic storage facilities for natural gas. The advent of analog computers" has increased materially the practicality of solving nonlinear partial differential expressions. Several iterative numerical and graphical methods14,15,16 have been developed to solve nonlinear equations. However, it appears that the pair of simultaneous nonlinear partial differential equations involved in problems of this nature are not directly susceptible to solution by presently available analog computer or formal iterative numerical techniques. Nevertheless. graphical analyses afford a means of obtaining data of engineering value without special equipment. MATHEMATICAL CONSIDERATIONS Since the length of the conduit is large in comparison to the cross section in the cases to be considered, it is possible to treat the characteristics of the flow as independent of position in the cross section of the conduit. This possibility follows since the energy- connected with the velocity profile is small compared to that required to overcome the friction associated with its movement throughout the length of the line. Average values of the pressure. velocity. kinetic energy. momentum, and specific volume may he assigned to the fluid at any particular cross section. From a mathematical viewpoint this may be expressed in the following way for velocity: µ = µ(?X)..........(1) The uncertainties introduced by such assumptions usually are negligible when the ratio of length to diameter is greater than the order of 1.000. On this basis a volume element ma!. be considered to occupy the entire cross section of the conduit. Such an element is presented in Fig. 1.

Jan 1, 1951

By R. H. Olds, B. H. Sage

The transient flow of gases in long pipe lines is a problem of industrial interest. The present discussion deals with the application of the conservation of momentum and material to the transient flow of gas in conduits which are long with respect to their diameter. Solutions of the resulting equations include consideration of variations in friction and specific volume of the fluid as functions of time and position along the conduit. The changes in state along the pipe line are established as a function of time. The methods proposed may be extended to other situations. The flow of compressible fluids under steady conditions&apos; has been considered in detail. Primary emphasis was placed on the development of simple means of taking into account the non-uniform flow&apos; realized in long conduits under such conditions. Binder2 discussed the essential differences between the flow of compressible and uoncompressible fluids. Bonilla" proposed direct methods of solution for equations describing isothermal flow in long pipes. Similar considerations limited to steady flow have been discussed by Ruth.&apos; Palsgrove 5 sugrested a graphical means of solving specific problems relating to the flow of gases in conduits of uniform section. Some of the basic concepts of the flow of a compressible viscous fluid in straight tubes have been described by Kuo.6 Problems of this type require knowledge of the equation of state of the fluid. In many cases it liar been convenient to assume that the fluid follows the relationship ascribed to a perfect gas. The treatment of unsteady flow of compressible fluids is less complete. This state of affairs result* from the fact that the differential equations relating pressure and flow rate with time and position for unsteady flow are nonlinear in character.&apos; Muskat and Wyckoff presented an excellent treatment of the situation in laminar Bow where inertia forces were not of controlling importance. Somewhat earlier Hurst9 discussed the uncteady flow of fluids in petroleum reservoirs. Helhering-ton. MarRoberts. and Huntington&apos;" established experimentally the pressure distribution and accumulative flow rate of natural gas through an unconsolidated sand. Recently Joffe11,12 conhitlcretl the specific problem of the flow of natural gas in relatively long.,. pipe lines for unsteady conditions with emphasis upon the economic feusibility of the storage of gas in such a reservoir. These discussions were based upon approximations of the partial differential equations applying to the condititons of flow. The results were descriptive of the physical situation and indirated the effertiveness of large pipe lines as cyclic storage facilities for natural gas. The advent of analog computers" has increased materially the practicality of solving nonlinear partial differential expressions. Several iterative numerical and graphical methods14,15,16 have been developed to solve nonlinear equations. However, it appears that the pair of simultaneous nonlinear partial differential equations involved in problems of this nature are not directly susceptible to solution by presently available analog computer or formal iterative numerical techniques. Nevertheless. graphical analyses afford a means of obtaining data of engineering value without special equipment. MATHEMATICAL CONSIDERATIONS Since the length of the conduit is large in comparison to the cross section in the cases to be considered, it is possible to treat the characteristics of the flow as independent of position in the cross section of the conduit. This possibility follows since the energy- connected with the velocity profile is small compared to that required to overcome the friction associated with its movement throughout the length of the line. Average values of the pressure. velocity. kinetic energy. momentum, and specific volume may he assigned to the fluid at any particular cross section. From a mathematical viewpoint this may be expressed in the following way for velocity: µ = µ(?X)..........(1) The uncertainties introduced by such assumptions usually are negligible when the ratio of length to diameter is greater than the order of 1.000. On this basis a volume element ma!. be considered to occupy the entire cross section of the conduit. Such an element is presented in Fig. 1.

Jan 1, 1951

By R. P. Aikman, F. G. Miller, J. M. Podgursky

As part of a larger study of the mechanism of froth flotation of coal, the rates at which coal particles of various size and specific gravity react to froth flotation were investigated. Results of this study show that in flotation: I) recovery rate increases, but selectivity decreases with a decrease in particle size down to 100 mesh, and 2) recovery rate is constant for all sizes between 100M and 325M. n response to the growing demand for low-sulfur coking coal for iron making, the coal industry is continually striving to perfect methods for cleaning coal to acceptable ash and sulfur levels while maintaining maximum product yield. By present standards the industry has adequate processes for cleaning coarse coal, i.e., + 28 mesh, at almost any desired specific gravity. However, in the case of fine coal, i.e., —28 mesh, neither of the two existing processes - froth flotation or hydrocycloning — in its present state of development yields products that are comparable in ash and/or sulfur content to products normally obtained from coarse coal processes. The work outlined in this paper is part of a larger study directed toward maximum exploitation of froth flotation for fine coal processing. The concepts and data presented are now serving as a basis for designing fine-coal circuits in which improved efficiency is obtained by optimum use of froth flotation with other fine-coal processing methods. The paper includes: 1) A discussion of the value of a detailed wash-ability study as a method of assessing the problems associated with fine coal processing, 2) A general discussion of hydrocyclone principles, included to serve as a basis for understanding the mechanism of coal flotation, and 3) A detailed discussion of the mechanism of coal flotation, as well as the research leading to the optimum use of froth flotation in combination with other fine-coal cleaning methods to provide efficient fine-coal processing. Our study of the rates at which coal particles of various size and specific gravity react to flotation shows that in flotation: 1) recovery rate increases but selectivity decreases with a decrease in particle size down to 100 mesh, 2) recovery rate is constant for all sizes between 100 mesh and 325 mesh, and 3) the flotation process effectively rejects only those extremely fine particles which do not contain surface carbon. (Because of this feature, froth flotation is an excellent method for rejecting clays - the only extreme fines in - 325-mesh coal that are always carbon free.) Washability studies of flotation products are used to assess flotation efficiency. These studies show that: 1) the increase in percent sulfur in flotation products above the theoretical sulfur content as defined by the washability study is due almost entirely to flotation of fine high-specific-gravity particles that are part coal and part pyrite, and 2) in a given size range particle floatability decreases with an increase in particle specific gravity. Error curves are explained and are used to compare the mechanisms of coal flotation and hydrocycloning. These comparisons show that hydrocyclone performance is affected primarily by particle mass, i.e., particle specific gravity and size, whereas coal flotation performance is dependent on both the particle mass and the coal surface available for bubble attachment. Since the error curve is a basic tool for rating the efficiency of any coal processing system, it will be useful to quickly review the principles of error curve construction. RATING COAL-PROCESSING EFFICIENCY BY THE ERROR CURVE The organic component of coal is of lower specific gravity than its impurities, and the most effective principle for coal concentration is therefore separation on the basis of specific gravity. However, since there is no sharp dividing line between pure coal and pure ash components, specific gravity must be closely controlled if the product is to have acceptable quality at maximum yields. In turn, the basis for close control in any coal processing system is the reference standard provided by precise laboratory washability studies. In these studies, coal is carefully separated into a series of progressively higher specific gravity fractions to establish a relationship

Jan 1, 1968

By T. Yamasaki, S. Usu

Adsorption of potassium dodecyl xanthate from aqueous solutions on artificial and natural zinc sul-fides was studied by means of infrared absorption spectroscopy. The adsorption species and their stabilities varied depending upon the conditions of the surfaces of the zinc sulfides. Adsorption products were analyzed after they had been removed from the surface with pyridine. Zinc dodecyl xanthate was confirmed for surfaces covered with oxidized products while dodecyl alcohol and carbon disulfide were detected on purified or weakly oxidized surfaces. It is of great significance to study the adsorbed species of collectors on the surface of sulfide minerals with a view of increasing our understanding of the mechanism of flotation. Compared with other methods, infrared spectroscopy promises to be of particular value in determining the nature of the species adsorbed at the mineral/solution interface since it gives direct identification of the adsorption products; and, furthermore, it has an advantage over the electron diffraction technique which has been employed in similar problems in that infrared spectroscopy utilizes radiation of very low energy so that the probability of changing the unstable surface films during examination should be correspondingly decreased. Infrared spectroscopic studies concerned with sulfide mineral flotation have already been reported by several investigators on zinc sulfide-hexanthi01&apos; and lead sulfide-xanthate2,3 systems. The purpose of the present study was to investigate the adsorption of potassium dodecyl xanthate (KDX) at the zinc sulfide-aqueous solution interface by means of infrared spectroscopy. Rarely is the pure zinc sulfide-xanthate system encountered in practical flotation since zinc sulfide is usually activated with small amounts of certain metallic ions, such as copper ion. However, investigation of the pure zinc sulfide-xanthate system appeared promising for studying the fundamental mechanism of the adsorption of xanthate on the sulfide minerals. Although there are few cases where xanthates having an alkyl radical higher than hexyl are employed in practical operations, KDX was used in this study since it was reported that the adsorbability of xanthate on zinc sulfide was increased with an increasing number of carbon atoms of the alkyl radicals.4 EXPERIMENTAL Samples: Experiments were made on artificial zinc sulfide and natural sphalerite. The artificial zinc sulfide was obtained commercially from Dainihon Toryo Co. as a fluorescent pigment of the purest grade A. Considering the fact that there are often cases where the surface of sulfide minerals are apt to be oxidized so that the adsorption of xanthate at sulfide mineral/solution interfaces may be substantially affected, two different procedures were employed in preparing the samples of the artificial zinc sulfide. 1) The zinc sulfide was washed with hot concentrated ammonium chloride solution (300 g per liter) to remove surface oxidation products and followed by washing with deoxygenated hot distilled water by centrifugation until the constant electric conductivity of the solution was reached (Sample I) (specific conductivity of the solution = 8.6 x l0-5 ohm-&apos; cm-&apos;). 2) Sample I in a suspension of 5% by weight was oxidized with a 1.5% aqueous hydrogen peroxide solution for about one hour, and then was washed with distilled water as mentioned in the preparation of Sample I (Sample 11) (specific conductivity of the solution = 1.0 x 10"4 ohm-&apos; cm-&apos;). Both Samples I and II were dried under vacuum and stored in a vacuum desiccator. The specific surface areas of the samples determined by the BET method using carbon dioxide gas were 19 x l04 cm2 per g for Sample I and 35 x l04 cm2 per g for Sample 11. In addition, a sample which was derived from Sample I was also prepared. In 40 ml of 3 x 10-2 M zinc sulfate solution was placed 2 g of Sample I for 2 hours, washed with distilled water by successive centrifugation until no sulfate ion could be detected and dried under vacuum (Sample 111). The purpose of this treatment will be described later. Natural sphalerite was carefully selected by hand, ground in a mechanical agate mortar for about 40

Jan 1, 1965

By Byoung Whie Lee

In order to investigate the change in surface energy as a function of cold work ad environment, the contact angles between a liquid and the surface of elec-tropolislzed aluminum with various degrees of cold work were measured. Specinlens cut from aluminum rod (99.99 pct Al) were annealed at 600°C for 24 hr and then cold compressed parallel to the drawing di-rectzon of the rod in increments of approximately 10 pcl from 0 to 70 pct. The sections, taken transversely to the drawing direction, were mechanically and electro chemically polished. Contact angles between the sessile drop of distilled water, glycerin, and glycol and the specimen surface were measured optically. The differences in interfacial energy were calculated from the contact angle data. The effects of chemical washing and surface roughness of the specimen on the contact angle were also studied. The liquid contact angle was a linear function of the degree of cold working (D) ad changed markedly with differed liquids. THE plastic deformation of polycrystalline metals induces a preferred orientation in crystal structure. A preferred orientation changes the atomic density of a metal surface. This change in surface atomic density brings about the changes in surface interactions of the metals."&apos; Also, the plastic deformation of metals raises the internal energy by increasing the stored energy.&apos; Consequently, the total Helmholtz free energy of the metal increases and, in turn, the surface free energy of the metal. In order to study the effect of plastic deformation on solid surface phenomena, the liquid contact angle of a sessile drop made on cold compressed and elec-trochemically polished aluminum was measured. The preferred orientation in aluminum, due to uniaxial compression, is known to be [110] direction parallel to the compression axis. However, this description is only a first approximation of a rather complex orientation. In actuality, half the crystallites are more than 10 deg from this orientation, regardless of the amount of compression." For randomly oriented fcc crystals, the average surface atomic density can be calculated as follows: The number of atoms in a unit volume is 4/a3, where a is a lattice constant. Hence, the number of atoms per unit surface area is about (4/a3)2/3 = 2.52/a2 However, when the preferred orientation took place along [110] direction, the surface atomic density is as follows: The area of (110) plane of a unit cell, considering ridges and valleys, is BYOUNG WHlE LEE, Member AIME, is Research Metallurgist, Atomic Energy Research Institute of the Republic of Korea, Seoul, Korea. Manuscript submitted May 29, 1968. IMD 2 x J2- a x Ga = 6a2 Since this plane contains 4 atoms, the surface atomic density is 4i6a2 = 2.3/a2 Upon changing from random to preferred orientations, the surface atomic density decreases about 10 pct. The increase in the stored energy and the change in surface atomic density due to plastic deformation would certainly alter the surface tension of a metal. EXPERIMENT High purity aluminum rod of 6-mm diam (99.99 pct Al, obtained from Johnson, Matthey & Co., Ltd, London, England) was cut into sections approximately 1 cm long. The transverse cross section was mechanically polished. Then, the specimens were annealed in air at 600°C for 24 hr. Thus, eight annealed specimens were uniaxially compressed at room temperature from 0 to 70 pct of cold working with an increment of 10 pct. The extent of cold working was determined by the percentage of reduction in axial length to the original length. The specimens were further polished mechanically and, then, electrochemically with the Modern Battelle Type 1 electropolishing solution with a current density of 0.3 to 0.4 amp per sq cm and an electrode potential of 8 to 12 v at the solution temperature of 78" to 82°C for approxirr~ately 5 min. The Modern Whlte Diffusing Screen \t/ --------------- re Goniometer for Mercury Lamp ^-^ Sessile Drop ¦=• Condenser c=> Microscope l_*~_i bJ Mlcromster Filer with Protmcter Fig. 1—Schematic diagram of apparatus set-up for liquid contact angle measurement.

Jan 1, 1970

By John D. Verhoeven

A technique has been developed for carrying out normal freezing experiments with a current density of 2000 amp per sq cut passing through the solid-liquid interface. The equation relating the effective distribution coefficient to the equilibrium distribution coefficient in electric field-aided solidification, originally developed by Huckc et al.,1 has been modified for the case of concentrated solutions. Preliminary experiments on the Sn-Bi system give qualitative agreement with the equation. The data are analyzed by a slightly novel use of the normal freeze equation which allows one to determine the effective distribution coefficient more easily. Very extensive mixing in the liquid was found at these high current densities and it is postulated that the mixing results from a vertical component of the magnetic Lorentz force generated by the electric current. In the search for techniques of obtaining ultrahigh-purity metals the inefficient but very effective technique of electrotransport has received little attention. Electrotransport is most effective in the liquid state and a natural application, therefore, is to apply an electric field across the liquid zone of a zone-melting experiment. The present investigation was undertaken to study the effect of an electric field upon solidification of metals, so that the usefulness of electrotransport in such solidification experiments as zone melting could be determined. In zone-melting and normal-freezing experiments it is difficult to achieve complete mixing in the liquid in the immediate vicinity of the solidifying interface. Consequently a solute build-up will occur at the interface in the portion of the liquid where complete mixing does not occur (an equilibrium distribution coefficient, ko, less than one, and unidirectional atom motion will be implied throughout). This local solute build-up produces a corresponding rise in the solute concentration in the solid so that the ratio of the solute concentration between the solid and the bulk liquid is larger than the equilibrium distribution coefficient. This ratio is defined as the effective distribution coefficient, k,. The differential equation describing the solidification process may be derived by applying the continuity equation to an expression for the net solute flux at the interface. The solution to this differential equation then allows one to determine the solute distribution in the liquid and the relationship between k0 and ke. One of the most useful solutions to this equation was first derived by Burton, Prim, and Slichter,&apos; in which they assumed that a) the equilibrium distribution of solute was maintained on the plane of the interface, 11) the solute build-up ahead of the interface in the liquid disappeared at a distance 6 from the interface, and c) the solute distribution in the liquid was invariant with time. The following well-known relation between ko and ke was then obtained, where R is the rate of solidification and D the diffusion coefficient of the solute in the liquid. This equation appears to correlate the data from a number of different types of solidification experiments very well. Application of an electric field across the solid-liquid interface can produce an additional flow of solute atoms as a result of the electrotransport. When the polarity of the field is such as to direct the electrotransport flux away from the interface the solute build-up may be diminished, even to the point of producing a solute depletion and a consequent ke smaller than ko. The quantitative description of this process and the resulting form of Eq. [I] was first given by Hucke et al.1* and then inde- where E is the electric-field intensity and U is the differential mobility, i.e., the velocity of the solute atoms with respect to the solvent atoms per unit electric field. Both authors follow the method of Burton, Prim, and Slichter in their derivation, the only difference being the additional electrotransport term in the flux equation. It has been pointed out1,3 that Eq. [2] predicts the possibility of a noticeable increase in the purification of materials by solidification in an electric field. The validity of Eq. 121 has not been checked experimentally and it is possible that other factors&apos; arising from the presence of an electric field across

Jan 1, 1965

By W. W. Stephen, J. P. Walsted, W. J. Kroll

FOR the production of carbides, various furnace types are available, especially those using arc, resistance, and high-frequency heating. Selection of a specific means of heating depends primarily on the material to be treated and the physical properties of the carbide produced. In the present case, zirconium carbide had to be prepared on an industrial scale as a raw material for the production of anhydrous zirconium chloride. Considering that a rather expensive pure oxide was to be used, the arc-furnace treatment recommended for zircon sands in a previous publication&apos; was ruled out because of the considerable volatilization and dust losses caused by the blast of the arc. For this reason, either high-frequency or resistance heating seemed to offer more promise. Since there was not enough capacity of the former available, resistance heating was chosen. It was first thought that the Acheson silicon carbide furnace would be suitable for the present purpose, but the voltage in such a furnace, in which the current passes through the batch, varies from 220 to 75 v from the start to the end of a run. This variation is so great that a special tap transformer would have been required. Trouble was also expected by local melting of the carbide. Pure zirconium carbide melts at about 3527°C, but the melting point is brought down to 2427°C, according to Agte,2 when an excess of 6 pct C is present in the carbide. This we found confirmed by experiments in a high-frequency furnace. Excess carbon is needed in the batch to obtain a complete reduction. Fusion of the charge would cause great difficulties in an Acheson-type furnace because of the good electrical conductivity of the carbide as compared with that of the loose batch. Also, fused carbide is much more difficult to chlorinate than the spongy product that can be made in the radiation furnace described below. It was apparent that, to obtain a good-qual-ity zirconium carbide, the heat input would have to be well-controlled. The hairpin-resistor principle seemed to offer possibilities in this regard, and a furnace of this type was therefore developed. The advantages of the hairpin-resistor radiation principle have been discussed in previous publications, and a split-tube graphite-resistor furnace," now increasingly used in various laboratories, as well as a centrifugal quartz melting furnace4 of this type, has demonstrated the usefulness of this heating method. The hairpin-heater element has the following definite advantages over a straight resistor of the type used, for instance, by Georges:5 Its resistance is four times greater; it can expand freely; it is sturdier because of the larger diameter, and it has a larger radiation surface; there are no hot contacts that might wear out or overheat; only one clamp is used which permits assembling all electrical leads at one side of the furnace, making the other sides easily accessible to the operator. The shorter element and its larger diameter permit greater concentration of heat. The furnace developed is shown in fig. 1. The box (I), made of 2 1/2-in. graphite plates, has inside dimensions of 23x17x16 in. It contains the briquet-ted batch (2). The box is embedded in lampblack (3) up to the cover plate. The cover plate contains an opening for the gas escape (4) and for the observation hole (5), which permits measuring the temperature with an optical pyrometer. The cover plate is embedded in charcoal (6). The lampblack is contained in the insulating brick lining (7), held in the 1/4-in. sheet steel box (8). The graphite box is set on two rows of triangular graphite bars (9). The hairpin-heater element (10), the dimensions of which are given below the main drawing, extends horizontally in the graphite chamber and radiates freely on the batch. A graphite tube (11) keeps the lampblack from falling into the slot. The split electrode, which in reality is turned 90" against the drawing, is so arranged that the slot is vertical. The water-cooled packing gland (12) is insulated by an airgap from the heater element. A thin pipe (13)

Jan 1, 1951

By W. J. Houk, F. C. Hull

To clarify interpretations of grain structures and to assist in calculations of spatial grain size distributions, plane distribution curves have been determined for random sections through four regular polyhedrons approximating the shapes of metal grains. The characteristics of the distribution curve for the average metal grain are predicted. IT was realized early in the history of metallurgy that metals are polycrystalline aggregates and that the size and shape of crystals affects the properties of the material. Reaumur1 in 1722 employed the microscope to examine the fractured surfaces of steel and of white and gray cast iron and suggested a polyhedral arrangement of the crystals. The first extensive investigation of the form of crystal grains was carried out by Desch.2 He examined the disintegrated grains from a ß brass sample and noted that the number of faces per grain ranged from eleven to twenty and that the number of edges per face varied from three to eight and the maximum occurred at five. While it has been found practical to examine isolated grains only in exceptional cases, it is always possible to make a plane section through the metal and examine the shape of the grain sections on the plane of polish. Desch2 tried to determine the relation between the form of a polyhedron and that of its plane sections for comparison with distribution curves of numbers of sides per grain section of actual metal samples. The polyhedrons investigated were the rhombic and pentagonal dodecahedrons and the orthic tetrakaidecahedron. However, the frequency distributions of the number of sides of plane intersections were not sufficiently characteristic to decide which polyhedron most closely approximated the average grain in a metal. Determination of Statistical Shape of Grain in Space Scheil3 was interested in the problem of calculating the distribution of grain sizes in space from the easily measured distribution of grain section sizes on the plane of polish. Assuming that the grains were spheres and using the plane distribution curve for a sphere shown in Fig. 1, he employed a successive subtraction method to calculate the spatial distribution. In order to evaluate the accuracy of these calculations, Scheil and Wurst4 determined the actual distribution of grain sizes in space in their sample of ingot iron by polishing off successive layers and following every individual grain in a series of micrographs. From curves of mean radius of intersection of a given grain vs thickness of metal removed in polishing, Scheil and Wurst attempted to derive the statistical shape of a grain in space. Their calculated plane distribution curve for this shape is compared with the distribution curve for a sphere in Fig. 1. A table of values based on this curve was prepared for calculating spatial distributions of grains. The calculated and measured spatial distributions of their sample then agreed much better than when a spherical shape had been assumed. In the present paper, an attempt has been made to learn something about the average metal grain by studying in detail the effect of the shape of regular polyhedrons on the plane distribution of areas and shapes of areas produced by random sections through them. From the data presented below, it can be concluded that the plane distribution curve for the average metal grain differs in three fundamental respects from the curve derived by Scheil and Wurst. Polyhedrons Selected for Study The polyhedrons selected for the statistical study are illustrated in Fig. 2 and consisted of a cube, a figure formed by cutting off the corners of a cube at the midpoints of the original edges, a tetrakaidecahedron, and a pentagonal dodecahedron. The length of edge on any one figure is a constant. For the above models the edge lengths were 3.50, 4.00, 2.00, and 2.08 in., respectively. A cube was selected for one of the polyhedrons because of its simple geometry, because it is a form that by repetition can completely fill space, and because it represents a convenient degree of departure from compactness beyond which the shape of

Jan 1, 1954

By J. C. Purcupile, R. L. Morris

Present methods of roof support require that first a hole must be drilled, and then a toggle belt or grouted resin bolt be set. Automating this system is very difficult. Therefore, we decided to develop a system which would insert pins into the roof in one step. We think that this type of system can be automated much easier. It would then speed up the roof bolting operation and eliminate the need for a man to work under unsupported roof, making roof bolting a much safer job. There are two ways that a pin can be inserted in a mine roof without drilling a hole. It can either be pushed in, using a very high, constant axial force; or it can be hammered in like a nail. The former method involves very high compressive stresses in the pin, and requires complicated machinery to prevent buckling. Since hammering the pin does not require high axial forces buckling is not as likely. Also, experiments have shown that there are no problems associated with getting the pin to go in straight. We chose to develop the second method. While investigating methods for hammering a pin into a mine roof, we learned that piles were being driven 10 times faster than by conventional methods with a method called "orboresonance." We decided to turn the pile driver upside down, and drive pins up into the mine roof. Sonic Pin Setting Machine The machine consists of a steel bar supported at the nodal points of its first mode of transverse vibration (Fig. 1). A mechanical oscillator, driven by a hydraulic motor, is attached to one end of the bar. This provides the forcing function for the vibrations in the bar. The hydraulic power is supplied by a portable unit. When the forcing function is near the natural frequency of the bar, large amplitudes of vibration occur and require little power input. An anvil is attached to the bar at a point of maximum deflection, providing a means for striking the pin. Since the bar is being driven near its natural frequency, it takes little energy to accelerate the bar back and forth between each hit. This means that most of the power being put into the bar is going into driving the pin. This is unlike conventional pile drivers which use most of their power to accelerate the hammer back and forth between hits. The resonant frequency of the bar we used is about 250 Hz, which is in the audible range, hence the term "sonic pin setting machine." The system benefits are: (1) elimination of the two-step drilling and pin-setting roof bolt operation, (2) increased speed, (3) more intimate contact between the formation and bolts, (4) less expensive roof bolts, (5) higher integrity, (6) potential for automatic operation. Modifications During the months from Oct. to Dec. 12, 1974, under U.S. Bureau of Mines grant No. 00144104, "Projects on Coal Extraction," six members of the senior class at Carnegie Mellon University designed and built the experimental machine. They drove three pins into the Safety Research coal mine at Bruceton, Pa., and determined that the project was worth continuing. In January 1975 we began making modifications and repairs in preparation for a more extensive program of testing at Bruceton. The major items were: 1) Design and build a collapsible pin guide to keep the pin parallel with the line of travel of the lift table. 2) Move the anvil to the center of the bar. 3) Refinish the nodal holes and install new node pins and bushings. 4) Realign the bar in its frame. 5) Install a relief valve on the lift unit to control the upward force. The upward force that we exert on the pin is relatively small, so there is no tendency for it to buckle. This means that all we need to do is hold the pin straight during its initial penetration. This allows the bushing to travel up and down in a straight line. At the beginning of penetration, the bushing

Jan 1, 1977