Search Documents

By R. C. Mahon

THE importance of ground water control in glacial drift overlying mines is widely recognized. Adequate handling of the problem results in consider- able saving in overall pumping costs, as the cost of pumping the larger quantity of water under low heads from surface wells is more than offset by the decrease in the quantity of water to be pumped from the mine under high heads. Eliminating or partly reducing seepage of water through the ledge reduces moisture content of the ore, a factor especially important in iron ore mines, where a reduction of 1 pct in moisture effects a very material saving. An important though indeterminate saving is also brought about by the elimination of water in the working places underground. The Homer and Wauseca mines of Hanna Coal & Iron Co. at Iron River, Mich., cover 480 acres. When these mines were started it was possible to operate on only one 40-acre tract, as the depth of water over the remainder of the property was too great to permit operation. Although the average depth of the ground water over the area being mined at that time was less than 50 ft it was necessary to pump 1200 gpm from the mine, the greater part from a depth of 750 ft. The slate footwall and graywacke hanging wall are almost impervious, and it was apparent that seepage into the mine was mainly through the iron formation in which the orebodies were located. Analysis of the water in the iron formation showed it to be of the same character as that in the glacial drift, while the water in both walls was heavily mineralized, also indicating that the water passed much more freely through the iron formation.

Jan 6, 1954

By Stanislaus Skowronski

THE melting of cathode copper, usually containing 99.98+ per cent. Cu, would appear to be a simple matter. Owing to the well known affinity of copper for sulphur, however, so much sulphur is absorbed by the copper during the operation that a long and expensive refining process is required to remove it, and the final product is inferior in purity and lower in electrical conductivity than the original cathode copper. The furnace operation, as now conducted, includes the following stages: 1. Charging the cathodes into the furnace. 2. Melting the cathodes. 3. Oxidizing period-saturating the copper with cuprous sub-oxide and bringing the metal to the condition known as "set copper;" this is now done by blowing air into the molten bath of metal. 4. Reduction period, otherwise known as "poling," whereby the oxygen previously added is removed by covering the molten bath completely with coke or charcoal and introducing large poles of green wood; this reduces the cuprous sub-oxide, bringing the copper to the "tough pitch" stage ready for casting. 5. Casting Period. Many experiments have been made to obviate the long periods of oxidation and subsequent reduction, with no success. While the copper first, cast will be good, as indicated by the set surface of the bars, it is impossible to hold it to the "tough pitch" condition, and long before the whole charge has been poured the copper will become "overpoled," entailing numerous difficulties. Sulphur has always been blamed by the furnace men as the reason why this refining process is necessary, yet the literature on the subject does not sufficiently emphasize how small a proportion of sulphur will ruin copper for practical purposes.

Jan 3, 1918

By M. Amsterdam, F. Rothwarf, L. Muldawer

SILVER-cadmium near the composition AgCd shows three equilibrium phases. As with 13 brass, the high temperature phase is disordered body-centered cubic (8) and the low temperature phase has the ordered CsCl structure . However, there is an intermediate temperature phase which is hexagonal close-packed ((). In a recent paper, Speich and Mack' report on a study of the Ag-Cd eutectoid near the AgCd composition. Unfortunately, the phase diagram upon which they base some of their conclusions is incorrect. That diagram is taken from the Metals Handbook' and the error is that the 0 and ( phases have been interchanged. The Handbook gives the low temperature phase as hexagonal (designated 5) and the intermediate temperature phase as cubic ordered (designated . The error may be typographical or it may be one of confusion resulting from the use of 5, ,, and 0 for the intermediate phase in various papers. A careful search of the literature reveals that a number of authors have indicated the correct relative positions of the 13, 5, and 0 phases. The comprehensive work of Fraenkel and Wolf clearly stated that the high and the low temperature phases are either identical or are very similar. olander,' on the basis of electrochemical measurements, showed that the 13 phase is disordered and the 1 phase (designated 8" in his paper and in refs. 3 and 5) is ordered. Further work by Durrant5 using thermal and metallographic analyses provided a more precise phase diagram. A summary of these works was given by Hansen6 and shows the correct relative positions of the phases. Owen, Rogers, and Guthrie7 located correctly the upper two phases by X-ray diffraction. Their failure to find the low tem-

Jan 1, 1954

By Harold Linke

THE following article presents notes and data compiled and computed by the writer for use in the determination of: size and slope of mill launders, details of junction boxes and downspouts, and distribution of pulp. It also includes pulp formulas, volume of discharge through bushings, paths of discharging streams, banking of turns and curves. In the design of a concentrating mill, the draftsman usually considers launders to the extent of providing ample "head" for transmission of pulp from one department of the mill to another. The superintendent of construction aims to build his launders wide and deep, and on a slope steep enough to ensure positive flow. So launders are laid generally on too steep a slope, with the result that the repair gang works to maintain launder bottoms and sides against the erosive action of the conveyed pulp. To this end many kinds of liners have been devised: concrete, mastic, white iron, glass, rubber. True, the reduction of slope to the point where a pulp will flow with minimum wear, will minimize labor and expense; but when the desired slope is not predetermined, the millman hesitates to readjust his launder slopes by cut-and-try methods. To the end that the desired size and slope may be found readily, the writer has: (1) conducted experiments with pulps of different specific gravity, screen analysis and dilution; (2) gathered a few graphic data from standard reference works (such as Peele's Mining Engineer's Hand-book and Taggart's Handbook of Ore Dressing); (3) computed several tables; and compiled results that have proved dependable for Utah Copper ore. It is quite possible that the following tables and graphs may not be applicable to all ores, but it is hoped that they may prove helpful, even in slight degree, in alleviating a portion of the trouble and migraine of some other millman.

Jan 1, 1939

By W. W. Mullins, F. A. Nichols

Solutions are developed, assuming surface diffusion and both internal and external volume diffusion, for the relaxation of bodies slightly perturbed from spherical and cylindrical geometries. Combined with those previously published for the nearly planar case, these results provide a means of gaging the relative contributions of the two diffusional proc-cesses in any given case. It is shown that in all sintering experiments to date, and probably in any attainable in practice, surface diffusion has played the dominant role, although most previous authors have assumed otherwise. It is also shown that surface diffusion predominates in normal field-emission tip blunting and also for the coalescence of gas bubbles introduced into metals by a bombardment. The surface-diffusion solutions for a perturbed sphere are combined with previous results for volume diffusion to show that the inclusion of interface diffusion permits considerably larger spheres to develop in diffusion-controlled precipitate growth before the onset of instability. A mechanism is also proposed for the spheroidization of precipitate platelets as well as rods. In a previous paper1 the relaxation of a nearly plane surface to flatness by the combined action of the transport processes of viscous flow, evaporation-condensation (in a closed system), volume diffusion, and surface diffusion has been analyzed under the assumption that all surface properties are independent of orientation. In this treatment, criteria were developed for deciding which process predominates, and solutions valid in the latter stages of the sintering of small wires and particles to a plane were obtained. A numerical solution, valid throughout the entire particle-sintering process for the case of surface diffusion, was subsequently obtained by the present authors.' It was found that the analytic solution (which assumed small slopes everywhere) is accurate to within -10 pct when the maximum slope of the profile is less than 0.3; the wire-sintering problem has also been solved nu- merically for the case of surface diffusion and here again the results converge to the analytic small-slope solution at late stages of the process, the two solutions agreeing in this case to within 10 pct when the maximum slope of the profile is less than -0.6. The purpose of this paper is to extend the perturbation solutions to nearly spherical and nearly cylindrical geometries. We treat only the two principal diffusional processes, i.e., surface and volume, but for these geometries we discuss volume diffusion both inside and outside of the solid. Our results, when coupled with Mullins' solutions1 for nearly planar surfaces, provide criteria for gaging the relative contributions of surface and volume diffusion to the over-all transport process in three basic geometries. A very interesting feature in the cylindrical case is the occurrence of instability for longitudinal perturbations with wavelengths greater than the cylindrical circumference, a classical result. This instability of the cylindrical surface is applied to give a quantitative explanation for the often-observed "erratic" pore closure in the late stages of the sintering of wire compacts; also, the theory previously presented for the spheroidization of rod-shaped precipitates by surface (interface) diffusion' is expanded now to include volume diffusion inside and outside of the particle. The results for circumferential perturbations on a long cylinder allow quantitative estimates for gaging the relative importance of surface or volume diffusion in the early stages of the sintering of spheres or wires. The results here demonstrate clearly that surface diffusion has played a very important, if not dominant, role in all sintering experiments discussed in the literature, although the surface-diffusion contribution to the kinetics has usually been ignored. The results for the sphere (surface-diffusion case) are added to the results obtained previously by Mullins and sekerka3 concerning instabilities of a growing spherical precipitate particle (with interface diffusion disallowed) to obtain a general solution to this problem including interface diffusion. The inclusion of interface diffusion is found to increase significantly the range of stability of a growing spherical precipitate for typical metallurgical cases. The following assumptions are made: (i) the initial surface lies everywhere near and has a slope differing only slightly from that of the reference

Jan 1, 1965

By Craig R. Barreft, Oleg D. Sherby

The steady-state creep characteristics of pure polycrystalline copper were studied in the temperature range 400" to 950°C and in the stress range 400 to 7000 psi. Tests were conducted in dry deoxidized hydrogen and all specimens exhibited high ductility before fracture. Two activation energies for creep were established as a function of temperature. Above about T/T, = 0.65, the activation energy for creep was 48,000 cal per mole whereas between 0.5 and 0.65 T, it was 28,000 cal per mole. The observed temperature dependence of the activation energy for creep follows the same trend as exhibited by the self-diffusion coefficient of copper in copper single crystals and silver in silver single crystals. It is therefore believed that the rate-cmtrolling mechanism in creep of copper in the stress and temperature range studied is diffusion-dependent and is probably associated with a dislocation-climb process. The low activation-energy region is attributed to enhanced volume difFusion from the presence of dislocations which act as short-circuit paths for diffusion. THERE is extensive experimental evidence1,2 that the activation energy for creep, Q,, for pure poly-crystalline metals tested at temperatures above one half the absolute melting temperature (0.5 Tm) is a constant and equal to the activation energy for volume self-diffusion, Qsd This equality is generally interpreted as meaning that creep in this temperature range is controlled by a dislocation-climb process. The existence of high-temperature creep activation energies not equal to the respective self-diffusion values has been suggested both theoretically3"5 and experimentally.6-8 Two examples of apparent nonequality between Q, and Qsd have been reported for the cases of silver7 and copper,' where activation energies for creep much lower than those for self-diffusion persist to rela- tively high temperatures (up to 0.6 T,). These observations suggest that dislocation climb may not be the only important process in the high-temperature deformation of these metals. That dislocation climb does indeed occur relatively slowly in these two metals due to their low stacking-fault energy has been suggested by many investigators.9-10 Although the creep behavior of copper has been studied extensively at low temperatures, the high-temperature activation energy for creep is not well-defined. The data of Feltham and Meakin8 indicated that Q, is temperature-dependent above one half the melting temperature, equaling a value of -30,000 cal per mole at temperatures up to 550°C and increasing to a value of -49,000 cal per mole at 700°C. No data has been reported above 700°C. The value of 49,000 cal per mole is very near the value of Qsd for copper reported by Kuper et al." as 47,100 cal per mole. In view of the lack of high-temperature creep data and the apparent temperature dependence of Q, for copper the present investigation was undertaken to determine the value of Q, over the temperature range of 400" to 950°C. It was hoped that such a study would clearly document the temperature dependence of Q, and yield significant information as to the nature of the rate-controlling creep mechanisms. MATERIALS AND PROCEDURES The material used in this investigation was high-purity OFHC copper. After rolling and recrystal-lization treatments spectrographic and chemical analyses showed only 0.0008 pct Ag, 0.0002 pctCa, 0.0002 pct H2, and 0.002 pct O2 as trace impurities indicating a purity of greater then 99.995 pct. Specimens were machined from cold-rolled sheet and the gage sections polished with 2/0 emery paper prior to annealing treatments. Annealing was done in both vacuum and dry deoxidized hydrogen atmospheres. No variation in creep strength was found as a result of the different annealing atmospheres. The final annealing temperature was either 700°, 800°, or 1000°C depending on the temperature range to be studied. These treatments resulted in average grain diameters of 0.03, 0.4, and 1.0 mm, respectively. The precise mechanical-thermal history of these

Jan 1, 1964

By R. D. Burlingame, T. L. Joseph, Gust Bitsianes

DESPITE almost fifty years of commercial practice, the sintering of iron ore has received little fundamental study. Much of the theoretical work1-'has dealt with the constitution of sinter produced under widely varying conditions. While these studies have broadened our knowledge of the changes that occur in the sintering zone and in the freshly formed sinter during the early stages of cooling, they provide little insight into the changes that precede the formation of sinter. These preliminary changes merit study as a part of the overall process. Hessle. working with beds of Swedish magnetite concentrates, was one of the first investigators to study the sintering process in its entirety. On the basis of temperatures observed at various levels of the bed during sintering, he postulated a number of distinct reaction zones to account for the chemical changes leading to the formation of sinter. A more direct method of attack is that of arresting the sintering zone after it has progressed part way through the bed. A study of a vertical cross section through such a quenched bed provides direct information on the changes taking place at various levels. This method was used by McBriar et al.' to show that several well-defined zones of chemical change existed within beds that were typical of British sintering practice. The same general method of attack was developed independently in the present investigation to study partially sintered beds typical of American practice. Experimental Sintering Equipment The sintering operation was carried out on an experimental scale with the equipment shown in Fig. 1. The refractory-walled sintering chamber A was 11 in. deep and averaged 9 in. in diameter. Air was introduced through a tapered flow section B, which contained the orifice C for accurate metering of the incoming air. This section was located directly above the square ignition housing D, which in turn rested upon the sintering chamber A. The bed was ignited with burner E. The required suction for the operation was furnished by a fan F, which had an air capacity of 500 cfm (stp). Hot exhaust gases from the sintering chamber were cleaned in the dustcatcher G before entering the exhaust fan. In the study of partially sintered beds, it was essential to find some technique for removing the entire charge from the sintering pot without disarranging the unsintered bottom portion. This problem was finally solved by sintering the charge in a removable basket, which snugly fitted the sintering chamber. This basket was constructed of two thicknesses of window screen and was lined with a 3/16-in. layer of asbestos paper. The bottom of the basket consisted of two thicknesses of wire screen, which were fastened to the basket wall. For high fuel mixtures, additional insulation was provided by a somewhat thicker layer of asbestos cement. Preparation of Partially Sintered Mixtures The moist feed was carefully placed in the sintering basket, to prevent segregation of the particles, which varied widely in size and composition. A thermocouple was placed in the center of the basket with the hot junction halfway down, and the mixture was evenly distributed around it. During ignition and throughout the sintering of the upper half of the bed, the hot junction temperature increased very little. When the sintering zone reached the halfway point, as indicated by the sudden increase in the hot junction temperature, the charge was quenched. During quenching the suction was turned off and the orifice was tightly stoppered to prevent further influx of air. At the same time, nitrogen was admitted to the sintering chamber through the orifice tap. As soon as the nitrogen had displaced the air and products of combustion, the charge was removed from the sintering pot for immediate dissection. It is impossible to preserve the exact zone structure of the bed at the instant that combustion is arrested unless the downward transmission of heat is also immediately stopped. Fortunately, heat transfer is very slow in beds containing a stationary fluid, especially if the particle size is small. It follows that the minimum quantity of nitrogen should be used to displace the air and that static conditions be established as soon as possible. A very steep temperature gradient across the combustion zone for some time after the quench was evidence of in-

Jan 1, 1957

By Carl F. Lutz, Robert F. Mehl

A layer of brass was formed on 0 brass using a vapor-solid reaction technique. The variation in composition with distance within the phase layer and across the a -ß interface was determined by an electron probe. The diffusivities were calculated as a function of concentration; the diffusion coefficient in brass was found to change by a factor of twenty-five over a compositional range of 8 at. pct. An explanation is proposed to account for the large change in the diffusivity, based on possible stresses in the diffusion zone; it is suggested that the concentration dependence of the thermodynamic factor might decrease the activation energy with increasing zinc content. ALTHOUGH the body of data on diffusion coefficients (D- values) in terminal solid solutions and in isomorphous systems is quite large, there is but little quantitative information for intermediate alloy phases. This paper recounts measurements of D-values for the ? phase in the Cu-Zn system. The experimental method employed consists in the forming of alloy layers and determining and analyzing the concentration-distance (c-x) curve. The experimental method employed could have been applied to several systems; the Cu-Zn system was chosen because the D-values in the a and ß phases are well known, and can thus be used for purposes of comparison. The rates of growth, of intermediate alloy layers are known for a number of systems. In nearly all cases the thickness varies parabolically with time, as to be expected if the rate of growth is controlled by the D-values. In a few cases, nonparabolic behavior has been noted.1 Nonparabolic growth may be the result of a) a variation of the composition at the phase interface with time, b) interface-controlled kinetics, c) short diffusion times coupled with long vacancy lifetimes (in vacancy diffusion),2 and d) crystal reorientation during diffusion in anisotropic systems.3 In the Al-Ni system4 and in the Al-u5 system parabolic growth kinetics are slowly approached after an initial transient period. In general those phases stable at a given temperature in a system A-B appear as separate phase layers when A and B are put in contact and given a diffusion he at-treatment. In most cases the compositions at the interface of adjacent phase layers are those read from the phase diagrams for the termini of the respective phases. This discontinuity in concentration is taken as independent of time, and the growth of one phase at the expense of another is assumed to be independent of interface kinetics, i.e., the rate of interface movement is controlled by volume diffusion in the phases concerned. wagner6 has given many solutions for multi-phase diffusion processes, assuming that the chemical diffusion coefficient, D, is independent of concentration, as have others. Jost7 has pointed out that the familiar Boltzmann-Matano solution is as valid for a (c-x) curve exhibiting concentration discontinuities at phase boundaries as for the usual single-phase case. Heumann and associates8,9 have applied this solution to the multi-phase case, but lacking concentration data within the several layers were forced to assume linear concentration gradients, thus calculating only average D-values. The purposes of the present study were: 1) to determine the dependence of D on concentration, 2) to calculate the intrinsic diffusion coefficients D?Cu and D?Zn, 3) to establish the time-law for the movement of the interface, 4) to determine the concentration limits at the ß-? interface, and, 5) to attempt to clarify the mechanism of diffusion. EXPERIMENTAL PROCEDURE The ? phase is exceedingly brittle; conventional solid couples and conventional sectioning methods were thus inapplicable. Vapor-solid couples were accordingly employed. Unfortunately the equilibrium vapor pressures of Zn for the ? phase are unknown; to escape this awkwardness, samples were enclosed in a capsule containing powder of an alloy of known composition, sufficiently large in quantity as to be effectively an infinite source, maintaining the concentration of Zn at the sample surface constant with time. The sources of Zn-vapor which can be employed in reaction with Cu, or a brass, or ß brass, to form a layer of ? brass satisfactorily wide in concentration range, are alloys of the phases ?, or ? + E or ? + d (depending on the temperature).

Jan 1, 1962

By L. D. Clark

Pay-out, the ratio of capital expenditure to annual cash return can be very revealing when employed to gage the merits of a proposed mining venture. It is a quantity, numerically but not physically equal to a factor, by which cash return may be discounted to equal required investment. The fewer the pay-out years, the greater the average annual earning power of the project. Considerable material has been written in the past about the most important and difficult problem mining management faces in evaluation of a property: the optimum production rate for the venture. What daily capacity should be adopted for the proposed operation that it may be the most rewarding to those underwriting it? H.C. Hoover has said, "The most important objective is the least cost per ton mined; and minimum working costs can only be gained by the most intensive production." Theoretically and practically, the quicker the ore is removed, the more profitable should be the venture because of the saving in fixed charges, the consequent lower unit costs and the interest unearned by the profit from the unmined ore. Yet, such performance will be tempered by policy and a restraint imposed by the ratio of capital expenditure to annual cash return. * The 'Annual net profit after taxes but including depreciation and depletion allowances. former will be based upon an analysis of the economic climate anticipated, with its many ramifications including the demand for the product, prices, tax laws, the conduct of labor and related wage scales. The variables and intangibles involved in estimating the optimum production rate for a mine do not readily lend themselves to mathematical relationships or equations and the problem can become complex indeed. The more readily applicable and relatively faster appraisal method will be used which, in addition to being reasonably adequate in most cases, will serve as a guide, should a more expanded and detailed estimate be desired. The first question is what is company policy with respect to the rate of investment return? This will depend on that significant period of time referred to as the pay-out, which can be defined as the estimated interval during which capital investment is returned through application of annual cash return to its recovery. Expressed another way, it is the ratio of capital expenditure to the annual cash return. For example, if the capital investment is $C and the annual cash return is $A (after Federal tax), then $C/$A = the pay-out period in years. That is to say, if $C = $1,500,000 and $A = $214,000, then which is the mathematical expression for the period of time it takes to recover the funds originally invested in a mining enterprise. The relationship yp = $C/$A can be useful — an expression which requires only the significant tern yp to be fixed; in other words, the long range investment policy. For what is the pay-out period but an expression of that policy in terms of the speed, within practical limits, with which an individual or company may want to recover capital expenditure? A policy by which pay-out will be fixed is imperative. This ratio must lie within relatively narrow limits governed by what is economically feasible. It cannot be too low, rendering the ratio impractical or absurd, nor too great, delaying the return of capital for reinvestment beyond a commensurate interval. What pay-out will govern this policy? Federal corporate taxes would seem to present the best measure. Consider mining in Canada where new mines are exempt from Federal income tax for 3½ yr from date of first production. This exemption expressly allows The Act states: "A corporation . . . i s not required to include the profits . . . for the period of 36 months commencing with the day on which the mine came into production in reasonable commercial quantites." a company to recover capital expenditure during the early stages of production. With such an incentive, it is logical to strive for as much capital redemption as possible during this period. Thus, 3½ yr would be a major contribution to the pay-out in Canada. Furthermore, it generally takes from 1½ to 3 yr to develop

Jan 1, 1963

By A. K. Mukherjee, J. E. Dorn, J. D. Mole

Investigations were carried out on the effect of polyslip on the strain hardening of aluminum single crystals. The orientations investigated were those lor which the tensile axis was in the [001], [111], [112], and [012] directions plus another for which the Schmid angles for {111}(110) slip were 1 deg. The experimental data were analyzed on a model based on the intersection of dislocations with particular emphasis on the effect of polyslip on the activation volume for inter-section. It is shown that the rate of strain hardening inreases for those orientations wherein attractive dislocation intersections occur and that those orientations which produce the greater number of such intersections exhibit the greater strain hardening. Good correlation of the data is obtained with the concept that attractive junctions, as proposed by Saada, Play an important role in accounting for the rate of strain hardening. EXISTING concepts on the nature and cause of strain hardening in fcc metals have been deduced principally from experiments on the deformation of single crystals under single slip. The effect of crystal orientation on the shapes of the stress-strain curves for single slip have been summarized by seegerl and more recently by Clarebrough and Hargreaves.2 Tensile specimens whose axes fall near the center of the [001]-[011] line of the standard triangle of the stereographic projection exhibit the longest range of easy glide (Stage I) and the lowest rates of linear hardening (Stage 11) whereas specimens whose axes lie near fie [001]-[111] line of the standard triangle have limited or no easy-glide range and exhibit somewhat higher linear strain-hardening rates. Specimens whose axes lie near the [001] or the [ill] poles do not exhibit easy glide and have the highest rates of linear hardening. Kocks3 has shown that the highest rates of linear hardening Occur under Polyslip when the tensile axis coincides with the [111] or the [ 001] pole. Since the rate of strain hardening is sensitive to specimen orientation and the incidence of polyslip, these relationships might help to discriminate between various dislocation models for strain hardening in fcc metals. Previous attempts to analyze the effect of orientation on strain hardening,1"3 however, did not provide a unique answer to this problem. Consequently the present investigation was undertaken wherein additional data, particularly that for the effect of polyslip on the activation volume for intersection, was also determined in order to provide more complete information on the details of strain hardening. Whereas analyses of these data reveal that several recommended models for strain hardening are at variance with the facts, good correlation of the data is obtained with the concept that attractive junctions4 play an important role in accounting for the rate of strain hardening. I) EXPERIMENTAL APPROACH seegerl demonstrated that slip in fcc crystals at low temperatures is dependent on thermally activated intersection of glide dislocations with forest dislocations. This has been confirmed by tests on single crystals of aluminum by Mitra, Osborne and Dorn5 and on polycrystalline aluminum by Mitra and Darn.' Thus in accord with Seeger's theory, the shear strain rate, ?, below a critical temperature, T, is where .V is the number of points of contact per unit volume between forest dislocations and glide dislocations, A is the area swept out per successful intersection, b is the Burgers vector, v is the frequency of vibration of the segment of the glide dislocation undertaking intersection, U is the activation energy for intersection, k is Boltzmann's constant, and T is the absolute temperature. For aluminum, which has an extremely high staeking-fault energy, the constriction energy is negligibly small and therefore the activation energy decreases practically linearly with the stress according to as will be recomfirmed later, where Uo is jog energy at the absolute zero, G and Go are the shear moduli at the test temperature T and O°K, respectively, L is the spacing of the forest dislocations, t is the applied shear stress for slip, and tGo is the stress field that must be surmounted athermally.

Jan 1, 1965

By Robert U. King, John W. Vanderwilt

THE Climax molybdenite deposit in Lake County 100 miles southwest of Denver is located in the central part of the mineral belt extending northeasterly across the state. Principal geographic features and geology are shown on Fig. 1. The first period of molybdenite mining, which began in 1918, ended in April 1919 because of limited demand and a price drop to about 72¢ per lb. During this time the ore came from the Leal level and surface outcrops at a higher elevation. Rate of mining was 250 tpd and several million tons of ore averaging 0.7 pct molybdenite were developed. Since April 1924, when the second period* began, Climax Molybdenum Co. has been the only operating company. Production in 1924 was 400 tpd and finding ore was a continual problem. When the White tunnel was extended, however, further ore was encountered. The orebody was thought to be tabular until 1926, when B. S. Butler recognized the relation of the developed ore on the Leal and White levels to a central area of fine-grained hydrother-mal quartz, and by 1929 diamond drilling had blocked out indicated ore reserves in excess of 100 million tons. In 1946, on the basis of information obtained from 25 miles of mine workings and a completed exploratory program involving over 200,000 ft of diamond drilling, the present authors reviewed and brought up to date the geology of the orebody. More recently Sears," employing microscopic techniques, made a study of hydrothermal alteration and mineralization, and Howell and Schassberger'" restudied available geologic data. Production (1953) of molybdenite ore has been expanded to over 25,000 tpd and total production from 1918 through 1953 has been: Tungsten, tin, and pyrite are byproducts and monazite also was produced from 1949 through 1951, after which it was not saved. A maximum of 15 to 20 tons of monazite was produced. Geology of the Area Pre-Cambrian crystalline rocks constitute most of the Mosquito Range for several miles to the north, east, and south of the Climax molybdenite deposit, see Fig. 1. To the west the crystalline rocks are in fault contact with shales and sandstones of Pennsyl-vanian age. Both crystalline rocks and sediments are intruded by dikes and sills of Tertiary age. Numerous faults with small displacements are to be found in the crystalline rocks east of the Mosquito fault and in the sedimentary beds to the west. Pre-Cambrian Rocks: The pre-Cambrian rocks consist of schist and gneiss, identified with the Idaho Springs formation, and granite with minor pegmatite correlated with the Silver Plume granite of the Silver Plume area. The Idaho Springs formation is a general term applied to pre-Cambrian schist and gneiss found over a large part of the Colorado Front Range. At Climax this formation consists largely of biotite-schist and quartz-biotite gneiss with minor quantities of plagioclase and orthoclase, although in places appreciable quantities of feldspar and quartz are present in the more gneissic varieties. Locally, especially along the contact with granite, recrystal-lization of the schist has produced coarser texture and a more pronounced than average gneissic appearance. The gneiss and schist have been mapped as a single unit by Butler and Vanderwilt (1933)" and by Singewald (1951).12 Schist predominates at the higher elevations of the Mosquito Range and in the area to the north and east of Climax. The regional trend of schistosity is northeast with varying dips to the east. Silver Plume granite and associated pegmatite intrudes the Idaho Springs formation. Silver Plume granite in many places and in the Climax district in particular has an irregular form, and many large and small inclusions of schist and gneiss occur within the granite. Granite predominates at the surface in the immediate vicinity of the area of hydrothermal alteration and extends for several miles to the northeast and southeast. As more schist is present at lower levels of the mine than in the upper levels, the suggestion is that the granite is sill-like in form,

Jan 1, 1956

By A. Lubinski, J. L. Logan, W. S. Althouse

A4ost gas twells and flowing oil wells are completed and treated through a string of tubing and a packer. Changes in temperature and in pressure inside or outside the tubing will: (I) if free motion of the tubing inside the packer is permitted, increase or decrease the length of the rubing; or (2) if free motion is prevented, induce forces in the tubing and on the packer. If pressure inside the tubing is greater than outside, the tubing may buckle helically even in the presence of a packer-to-tubing tension. The tubing will always buckle, and much more severely, if free motion is permitted. The buckling may be prevented by pulling the tubing in sufficient tension. The prediction of these forces and tubing movement has here to fore been based upon calculations that did not inciude helical buckling. This paper preseitts means with which these length or force changes can be calculated while taking into account the effect of helical buckling. To avoid damaging formations, failure of remedial operations, or damage to the tubing or packer, application is made to practical problems involving calculations of the required length of seals, amount of sluckoff or tension, and prevention of permanent corkscrewing. INTRODUCTION Leakage of a packer may result in costly failures of such operations as squeeze cementing, hydraulic fracturing, etc. To avoid such failures, the authors are often asked questions pertaining to the length of necessary seals, the amount of necessary slackoff, etc. Published work' does not take into account helical buckling of tubing. Investigation of helical buckling was prompted by the fact that allowance must be made for this phenomenon in order to provide relevant answers. In the past, theoretical work on helical buckling was confined to conditions for which such buckling does not The mathematical treatment of behavior in a buckled condition, given in the Appendix, is novel. Assumptions upon which this investigation is based are listed and discussed in a special section. The following are a few of the many kinds of problems which may be solved with this paper. 1. Consider a packer in which tubing may move. Such movement will occur after pressures and temperature are changed. The paper provides means for: (a) calculating the amount of such movement and, therefore. the required length of seals; and (b) calculating the necessary amount of initial slackoff, for which there is no danger of unsealing the packer, if the length of seals is given. Such calculations, as well as those which follow, tully take into account the fact that part of the movement ib due to elastic helical buckling of the lower part of the string. This buckling may occur even in tubing under tension. Insufficient initial slackoff for a given length of seals, or insufficient length of seals for a given slackoff, may result in costly failures. A field case of such a failure will be given further in this paper. 2. In the case in which tubing cannot move in the packer, changes of pressure and temperature result in tubing-to-packer forces and forces in the tubing above the packer, both of which may be calculated. This knowledge is important because, if these forces are too large, the) could damage the packer or the tubing. 3. For wells in which wireline tools are to be run through the tubing, the paper provides means to keep the tubing from buckling, thereby permitting free passage of tools. 4. In deep wells, mainly in the presence of large casing, tubing may become "corkscrewed", i.e., take a permanent helical set. A field case is described further in the text. Using this paper, one may calculate in advance conditions under which permanent corkscrewing would occur, and then take preventive steps. HELICAL BUCKLING Consider a string of tubing, freely suspended in the absence of any fluid inside casing, as shown in Fig. I(a). Now consider an upward force F applied at the lower end of this tubing. This force compresses the string; and if the compression is large enough (which is always the case in actual problems), the lower portion of the string will buckle into a helix, as shown in Fig. 1 (b). The lower end of the tubing is subjected to a compression F. This compression decreases with the distance from the bottom and becomes nil (neither compression nor ten-

By C. W. Arnold, H. L. Stone, D. L. Luffel

The purpose of this research is to determine (I) the efficiency of small banks of enriched gar driven by methane in displacing oil from a porous medium and (2) the effects of variation in bank size and composition of that efficiency. Most of the experiments were conducted in a sand-packed tube 20-ft long and 1/2-in. in diameter. The hydrocarbon system generally used was methane, butane and decane at 2,500 psia and 160°F. The results of these experiments indicate that, in the regions contacted by the gas, a small bank of an oil-miscible gas driven by methane can displace all of the oil in a piston-like manner. If the enriched gas is of such composition as to remain immiscible with the oil, displacement of oil is less efficient than for the miscible case, and the gas bank travels through the sand with a velocity less than that of the driving gas. These data along with theories discussed imply that smaller banks and less total gas are required when the enriched gas and oil are miscible. INTRODUCTION Widespread application of enriched-gas drive to the recovery of oil rests upon a key factor — the use of limited quantities, or "banks", of enriched gas. At the present time, the value of liquefied petroleum gas or other enriching agents discourages their use in a continuous injection technique, or even in a large bank, except in a few isolated reservoirs. If small banks of enriched gas driven by methane were as effective in displacing oil as is continuous injection, the enriched-gas drive process might be applied to a larger number of reservoirs. Previous research on the mechanics of the enriched-gas drive process reported by Stone and Crurnpl and by Kehn, Pyndus and Gaskell has utilized continuous injection of enriched gas. This work has shown that two types of displacements occur. With gases containing sufficient intermediates. the oil is displaced misciblv and complete recovery is obtained from the regions swept. When gases are used which contain insufficient intermediate hydrocarbon for miscible displacement, oil is displaced immiscibly. In the latter type, selective solution of the intermediate hydrocarbons causes a swelling and reduction in viscosity of the oil and leads to an increased recovery over that obtained by dry-gas (methane) drive. The size of the enriched-gas bank necessary for efficient displacement of oil is determined by those factors which cause deterioration of the bank. A differentiation may be made between those factors which operate on a microscopic scale and those which act on a macroscopic scale. On the smaller scale, the enriched gas mixes in the direction of flow by diffusion and convection with the fluids immediately preceding and following it. On the larger scale, the gas may by-pass the oil by flowing through permeable streaks, by overriding the oil because of density difference, or by fingering because of unfavorable viscosity ratios. In such cases, the enriching material tends to mix with the oil both laterally and in the direction of flow. The increase in effective area available for diffusion and dispersion of the enriching components leads to a faster degradation of the bank and a need for a larger bank than is necessary for those cases in which no by-passing occurs. The effects of such macroscopic factors in the deterioration of enriched-gas banks have been reported in a separate paper by Blackwell, Terry and Rayne. The present study was confined to the factors which operate on the smaller scale, in particular to the behavior of banks of enriched gas in sands uniformly swept by the gas. Experiments were designed to answer the following questions. 1. Can small banks of enriched gas driven by methane be used to secure oil recoveries comparable to those obtained by continuous injection of enriched gas? 2. What is the optimum bank size (the minimum bank size necessary to obtain a recovery comparable to that obtained by continuous injection of the same enriched gas)? 3. How many total pore volumes of gas must be injected to obtain the maximum recovery when the optimum bank size is used? 4. What is the effect of varying the number of enriching components in a gas bank? This report describes the experimental investigations and discusses the results in terms of their significance to reservoir behavior.

By W. M. Robertson

The kinetics of grain boundary groove formation on copper surfaces immersed in liquid lead have been studied over the temperature range of 400° to 900°C. The groove widths were Proportional to the cube root of the annealing time, indicating that the diffusion of copper through the saturated liquid-lead solution is the mechanism by which grooves form. The rate constant for the process can be calculated by a theory due to Mullins. Using published data for the solubility of copper in liquid lead, for the interfacial energy of the solid copper-liquid lead interface, and for the diffusion coefficient of copper in liquid lead, the calculated rate constants almost exactly reproduce the measured values over the entire temperature range. The decay of scratches placed on copper surfaces has also been studied. The rate constant for scratch decay agrees with that for grain boundary groove growth, though scratch decay is sensitive to convection currents in the liquid. The interaction of solid and liquid metals has been studied extensively and has been found to be rather complex. Many of the studies have been complicated by a host of competing effects, including temperature gradients, concentration gradients, the formation of one or more intermetallic phases, natural or forced convection, and the presence in both the solid and liquid of considerable amounts of impurities and alloying elements. Recently theories have been developed of changes in surface profiles driven by capillary forces,' which allow the interaction of the solid and liquid to be analyzed quite directly. The present paper reports a study of the formation of grain boundary grooves on pure copper immersed in liquid lead, which allows the theory to be checked quantitatively. The Cu-Pb equilibrium diagram is quite simple: there are no intermetallic compounds, copper is just slightly soluble in liquid lead, and lead is almost completely insoluble in solid copper.2 The Cu-Pb system has been studied extensively,3-9 and all of the quantities—interfacial energy, diffusion coefficients, and equilibrium solubilities-necessary to calculate the rate of groove growth by a volume-diffusion mechanism are known. The kinetics of grain boundary grooving and scratch smoothing have been studied on the noble metals and the iron group metals in a reducing atmosphere or in vacuum.10 The main interest of these studies has been the determination of surface-diffusion coefficients at metal-gas interfaces using the theories developed by Mullins.1 The present paper uses similar methods for the study of diffusion processes at the interface between two condensed phases. There has been one previous study" of the kinetics of groove growth in a solid-liquid system, which, however, was troubled by the fact that neither interface energies nor diffusion coefficients were known in the Ni-S system studied. THEORY The theory of grain boundary groove growth has been developed by Mullins for the cases of volume diffusion," surface diffusion," and a combination of the two processes.14 He has also analyzed the kinetics of the flattening of a scratched surface by these processes.l5,l6 Several assumptions and approximations were used in the derivations of the surface profile shapes. The applicability of these assumptions and approximations to the present system will be considered in the discussion. At the intersection of a grain boundary with an initially flat interface the equilibrium between the interfacial energy and the grain boundary energy establishes an equilibrium groove angle. This induces curvatures in the interface. The chemical potential of material at a curved interface is higher than at a flat interface, so that material moves away from the region of the grain boundary. Mullins' calculations indicated that the groove profile would be similar to that shown schematically in Fig. 1. Small humps form above the level of the original flat surface. For a volume-diffusion mechanism the separation, w, of these humps at a time, t, is given by and where co is the equilibrium concentration of the solid in the liquid, y, the solid-liquid interfacial free energy, O the volume occupied by a solute atom in the liquid, D the diffusion coefficient of the solid in the liquid, and kT has its usual meaning. For a surface-diffusion mechanism the groove width is proportional to the fourth root of the time. For grooves forming by a combined surface and volume-diffusion mechanism the exponent of the

Jan 1, 1965

By C. E. Hottman, R. K. Johnson

Fluid pressure within the pore space of shales can be determined by using data obtained from both acoustic and resistivity logs. The method involves establishing relationships between the common logarithm of shale transit time or shale resistivity and depth for hydrostatic-pres-sure formations. On a plot of transit time vs depth, a linear relationship is generally observed, whereas on a plot of resistivity vs depth, a nonlinear trend exists. Divergence of observed transit time or resistivity values from those obtained from established normal compaction trends rinder hydrostatic pressure conditions is a measure of the pore fluid pressure in the shale and, thus, in adjacent isolated permeable formations. This relationship has been empirically established with actual pressure measurements in adjacent permeable formations. The use of these data and this method permits the interpretation of fluid pres.rure from acoustic and resistivity measurements with an accuracy of approximately 0.04 psilft, or about 400 psi at 10,000 ft. The standard deviation for the resistivity method is 0.022 psi/ft, and for the acoustic method 0.020 psi/ft. Knowledge of the first occurrence of overpressures, and of the precise pressure-depth relationship in a geologic province, enab1es improvements in drilling techniques, casing progroms, completion methods and reservoir evalzmtions. INTRODUCTION CENKRAL STATEMENT Operators engaged in the search for and production of hydrocarbon reserves in Tertiary basins are more and more frequently confronted with complications associated with over pressured (abnormally high fluid pressure) formations. This is particularly true in the Texas-Louisiana Gulf Coast area. The problems associated with these formations are of direct concern to the combined activities of all phases of operations, i.e., geophysical, drilling, geological and petroleum engineering.' - Knowledge of the pressure distribution of a given area of operations would greatly reduce the magnitude of many of these complexities and in some cases would completely eliminate specific problems. his pape; presents techniques developed for estimating formation pressures from interpretations of acoustic and electric log data. Specifically: the acoustical and electrical properties of shales, reflected by conventional acoustic and electrical surveys, can be used to infer certain reservoir properties, such as formation pressure, at any level in a well. It has been possible to develop these techniques because of a firm understanding of the basic principles that govern and apply to such overpressured provinces. NORMAL PRESSUKES Normal pressures refer to formation pressures which are approximately equal to the hydrostatic head of a column of water of equal depth. If the formations were opened to the atmosphere, a column of water from the ground surface to the subsurface formation depth would balance the formation pressure. On the Gulf Coast, the shallow, predominantly sand formations contain fluids which are under hydrostatic pressure. These formations are said to be normally pressured or to have a normal pressure gradient.* Experience has shown that the normal pressure gradient on the Gulf Coast is approximately 0.465 psi/ft of depth. OVERPRESSURES Formations with pressures higher than hydrostatic are encountered at varying depths in many areas. These formations are referred to as being abnormally pressured, abnormally high pressured, or overpressured. Formation pressures up to twice the hydrostatic pressure have been observed. These formations require extreme care and much expense to drill and to exploit. COMPACTION-FLUID PRESSURE RELATIONS THEORY The generation of overpressured formations in Tertiary sections of the Gulf Coast and several other Tertiary sedimentary basins is, in general terms, considered to be primarily the result of compaction phenomena.' This portion of the paper presents a brief review of the theory which associates compaction and fluid pressure relations, and should thus provide the necessary background for an understanding of the techniques presented. See Hubbert and Rubey' for a more comprehensive treatment of this subject. The theory of the consolidation of a water-saturated clay' has been well established by workers in soil mechanics. The concept is explained by a model with perforated metal plates separated by metal springs and water and enclosed in a cylindrical tube. Fig. 1 is a schematic representation of such a model (see Ref. 5, Fig. 27, page 74). The springs simulate communication between clay particles, and the plates simulate the clay particles. Mano-

Jan 1, 1966

By R. T. DeHoff, F. N. Rhines

The problem of determining the number of particles of a phase distributed randomly in unit volume c an opaque matrix from measurements made on random plane sections is closely investigated. A formalized derivation for the general case is presented. Applications of this formal result are made to specific types of aggregates dispersed in a matrix; circles, particles with flat circular ends, cylinders, and constant shape aggregates of ellipsoids of revolution. Quantitative measurements of the average geometric properties of these aggregates are developed. In 1953 R L. ullman' developed a technique for determining, from measurements made on random plane sections, the number per unit volume, Nv, of particles imbedded in an opaque matrix. Using meas urements previously developed for volume fraction, vV,' and surface area per unit volume, .SV,= he was able to determine average volume, average surface area, and average dimensions of particles, independent of size distribution, for spheres and circular disks,' as well as for uniformly sized cylinders of any axial ratio.4 The technique is mathematically rigorous for the cases studied. Recent studies of this problem have yielded rigorous solutions for the general case of cylinders, permitting evaluation of NV independent of size distribution and with all axial ratios intermixed. Generalization to shapes having flat, circular ends has been deduced. A solution has also been obtained for the ellipsoid of revolution, independent of size distribution, but requiring a constant axial ratio in the generating ellipses. In the following derivations, as in Fullman's work, it is assumed that the problem is purely a combination of geometry and probability theory,that is,eithe the particles to be measured are imbedded randomly in the matrix, or a sufficient number of random plane sections are taken to make the sample representative. A relationship exists between the number of par- ticles of a given size and shape that may be situated in unit volume (Ny) and the number of intersections a random plane can be expected to make with these particles (Na). It is the purpose of the following section to derive this relationship. The probability of Intersecting Convex Bodies. Consider a convex, closed surface, that is, one for which no two surface normals point in the same direction, situated at some arbitrary position and orientation in a cube of material that is one unit long at each edge. It is not necessary to assume that this surface is symmetrical. Let planes be constructed in the cube parallel to the top face and at random distances from it. Those planes which lie between the two planes which are just tangent to the top and bottom of the surface will intersect it. The probability that a plane will intersect the body may be defined as the limit of the fraction of planes that lie between the two tangent planes as the total number of planes constructed becomes infinite. This fraction, in the limit, is equal to the distance between the two tangent planes, DV, divided by the total length over which planes are constructed, which has been taken as unity. If the body is now rotated to a new orientation, applying the same argument, the probability of intersection is again numerically equal to the distance between tangent planes. Let DV ($, 0) be defined as the distance between tangent planes of a convex body as a function of orientation, Fig. 1. The probability, Pr, of intersecting the body with a randomly oriented and randomly positioned plane, is then equal to the average value of DV (0, $) over all possible orientations. It may be easily shown that for a system of spherical coordinates the probability of finding an orientation between Q and Q + de, $ and $ + d$ is (1/4n) sin $ dB d$, so that This relationship may be applied to each body in an aggregate of convex bodies. In particular, if the bodies in an aggregate are classified according to size and shape, and the ithsuch class is considered, Eq. 111 may be applied to this entire class, the probability of intersecting any body in this class being

Jan 1, 1962

By D. W. Reed, R. L. Reed, Tracht

Laboratory experiments on the reverse combustion of tar sands in a linear adiabatic system have shown that a highly upgraded oil can be produced from an exceedingly viscous, immobile oil. The dependence on the air-injection rate of peak temperature, combustion-zone velocity, oil recovery, air-oil ratio, residual coke and oil, fuel burned and distribution of product gases is shown graphically. Eflects of initial temperature, oxygen concentration, oil saturation and heat loss are discussed. Experiments bearing on the coking properties of heavy oils are mentioned and some results exhibited. Field application of the process hinges on the existence of adequate air permeability and the rate of reaction under reservoir conditions. INTRODUCTION It has been established that oil can be recovered from underground reservoirs by means of at least two fundamentally distinct methods involving in situ combustion of a certain fraction of the oil. Characteristic of both of these known methods is the production of oil from one or more wells by means of hot gases formed when a high-temperature reaction zone is advanced through the reservoir. In both cases, the reaction zone is created by heating certain of the wells to a sufficiently high temperature prior to the introduction of air, and the zone is maintained and advanced through the reservoir by appropriate control of the air-injection rate. In the first of these methods, which is called "forward combustion",' the combustion zone advances in a direction which is generally the same as that of the air flow; whereas in the second method, "reverse combustion",' the combustion zone moves in a direction generally opposite to that of the air flow. Forward combustion, on the one hand, is an ideal combustion process in the sense that a minimum of the most undesirable fraction of the oil is consumed as fuel in the form of coke, a clean sand is left behind and generated heat is used as efficiently as possible. However, the applicability of forward combustion is limited. Since the products of combustion, vaporized oil and connate water must flow into relatively cold regions of the reservoir, there is an upper limit on the viscosity of oil which can be moved by this process in a practical and economical fashion.' On the other hand, it is characteristic of reverse combustion that the vaporized oil and water together with the products of combustion are produced through sand which is already hot and has had its mobile liquid content eliminated. This means there is no upper limit on oil viscosity; indeed, the oil may be an entirely immobile semi-solid. However, fuel for the process is an intermediate fraction of the original oil, and the most undesirable fraction remains on the sand surface as a substantial deposit of coke. Since this coked material is not burned during reverse combustion, it represents energy which is available for the production of oil but is not used for this purpose. It follows that one can expect economics to be somewhat less attractive with reverse combustion than with forward combustion. Nevertheless, it is a process which is designed for reservoirs where forward combustion is impossible and, as such, has become a subject of experimental and theoretical investigation. In this paper, only experiments made with tar sands are discussed. DESCRIPTION OF THE PROCESS We proceed, then, to consider the process of reverse combustion in greater detail. Fig. 1 illustrates a temperature profile defining a combustion zone which moves from right to left when air flows from left to right. In Zone 1, the temperature is the initial reservoir temperature, and the tar sand is as yet unaltered. This statement must be modified to the extent that physical properties of the oil may be changed by low-temperature oxidation at reservoir temperature. As air passes into Zone 2, which has been warmed by conduction, it assists in vaporization of the very light ends (if there are any), and oxidation occurs at a significant rate. In this region, there is almost no production of carbon monoxide or carbon dioxide because predominantly addition-type reactions take place with the formation of oxygenated compounds such as aldehydes and acids together with water. The hydrocarbon-enriched and slightly oxygen-depleted gas stream enters Zone 3 where

By G. L. Tufford, R. L. Bleifuss

Low-grade manganiferous iron ores of Minnesota's Cuyuna Range, in general, do not respond to conventional mineral dressing techniques because of their fine-grained texture. Reducing these ores to magnetite with subsequent magnetic separation and flotation have not given satisfactory results because, in many instances, concentrate grade and manganese recovery are low. Metallization of iron and concurrent reduction of higher manganese oxides to MnO, as in the R-N process, followed by recovery of iron by magnetic separation and manganese by leaching, seems to be a technically feasible process. High-temperature x-ray diffraction studies show that solid-state reactions between iron and manganese, with the formation of intermediate iron-manganese oxides, occur during reduction and affect recovery of both iron and manganese from the final product. Solid state reactions also occur between FeO, MnO, and SiO, at temperatures as low as 900°C. The kinetics of these reactions are such that they become an important factor in the treatment of ores by the R-N process. These investigations suggest a temperature and gas composition cycle that would maximize both iron and manganese recovery. During the past ten years, iron ore shipments from the Cuyuna Range of Minnesota have decreased sharp1y. Because of adverse grade, structure, and cost, many Cuyuna ores are no longer competitive with high-grade foreign ores and domestic pellets. The low-grade manganiferous iron ores from the Cuyuna Range, in general, do not respond to conventional mineral dressing techniques because of their fine-grained texture. Reducing these ores to magnetite for subsequent magnetic separation and flotation has not given satisfactory results because concentrate grade and manganese recovery are often low. However, a technically feasible process appears to be metallization of the iron and concurrent reduction of manganese oxides to MnO with recovery of metallic iron by magnetic separation and extraction of manganese from the tailings by leaching. In 1962 the R-N Corp., with a grant from the Area Redevelopment Administration, conducted an amenability study of the metallization of manganiferous iron ore from the Cuyuna Range. The results of this preliminary investigation were sufficient to interest the Economic Development Administration in sponsoring further studies of the process with emphasis on secondary recovery of manganese from the nonmagnetic tailings. Inasmuch as the metallization process has considerable influence on the final form of the manganese - its texture and distribution between the magnetic concentrate and nonmagnetic tailings-the investigation included a study of metallization of the ore as well. Therefore, the investigation conducted at the Mines Experiment Station covered three interrelated phases: (1) laboratory R-N roasting studies and magnetic separation tests, (2) laboratory chemical extraction experiments of the nonmagnetic tailings, and (3) a mineralogical study of the crude ores and their various roast products. High-temperature x-ray diffraction investigation of the Fe-Mn-Si0,-0, system is the main topic of this paper and an extension of the mineralogical work. GENERAL GEOLOGY The Cuyuna Range is known for its complicated geologic structure, complex orebodies, and generally indifferent response to attempts at conventional beneficiation. Several geologists have made intensive studies of the Cuyuna Range, including Leithl (1907), ~darns' (1910), Zapffe3 (1925), Grout and Wolff4 (1955), and schmidt5 (1963), whose study was the most comprehensive of all. The Range is covered with glacial deposits - till, out-wash, and lake sediments -up to 250 ft thick. Bedrock stratigraphic units of the Cuyuna Range consist of three tightly folded Precambrian sedimentary formations. The lower unit is the Mahnomen formation, composed of 2000 or more feet of argillite, slate, siltstone, and quartzite. The middle unit is the Trommald formation, which varies from 45 to 500 ft in thickness and comprises the major iron-bearing formation. The upper unit is the Rabbit Lake formation, consisting of over 2000 it of argillite, slate, and interbedded lenses of lean iron formation. In the central part of the Cuyuna Range, the units have been folded into a series of

Jan 1, 1969

By L. Weyher, H. L. Lovell

This discussion is restricted to a very specific application of the cyclone - its use as a hydro-cyclone in the cleaning of fine coal. It is hoped that the development of the present data will assist in the further elucidation of existing qualitative models, and also in an enhanced application of the hydrocyclone and provide a base for further research. Discussed are the mechanisms of gravity separation in hydro-cyclones, test procedures, experimental observations, and industrial applications from these studies. Within the general area of unit operations, a considerable effort has been expended in theoretical and empirical research associated with cyclone operations. The motivation involves the industrial requirement for devices and techniques to manipulate small particles at low operating costs, a situation required in coal preparation. There are good reasons why the cyclone helps to satisfy this demand, because it combines operational simplicity (no moving parts) with versatility and high throughput capacity per unit area. The cyclone is one of the most widely applied tools in the process technologies. There are areas for potential cyclone application which have been only meagerly explored or not considered at all. This discussion is restricted to a very specific application of the cyclone - its use as a hydrocyclone in the cleaning of fine coal. It represents an initial presentation of a more comprehensive report. Coal preparation can appropriately claim the hydrocyclone since most of its predominant industrial uses have originated in this area and have spread into other applications, including the broad field of ore dressing, the petroleum industry, chemical processing, nuclear engineering and food technology. There is one operational principle common in all cyclones: A fluid is tangentially introduced into a cylindrical or conical container under pressure. A predominantly irrotational flow field1 is established within the cyclone (Fig. 1). The uniqueness of this flow is indicated by the variation in tangential velocity across the cyclone radius, which reaches a maximum a short distance from the center and decays toward the cyclone wall. In contrast, the tangential velocity in a centrifuge increases uniformly toward the wall. Usually two products are discharged from the cyclone. They differ in that one discharge consists predominantly of that portion of the feed fluid which moves along the wall axially away from the feed inlet, while the other consists predominantly of fluid spiralling along the central regions of the cyclone, in an axial direction opposite to that of the wall current. Fig. 2 indicates these discharge points schematically. The latter product may be termed the vortex-product, since it is discharged with the central vortex-current. In the case of conical cyclones, the former product may be referred to as the apex-product. Although the names "over- and underflow" are widely used, many cyclones are operated from extreme angular positions thus the proposed terms are less ambiguous. The cyclone feed fluid can be laden with solid particles or nonmiscible fluid drops. Such a feed component is discharged from the cyclone, after some residence time, into the one or the other product. Yet, the orifice through which a particle will leave the cyclone is dependent upon a number of factors. These factors, in a statistical sense, determine the path of the particle within the cyclone. Thus, different separation phenomena are possible and different process results attainable by the controllable variation of the particle path. It is then, to attain a fuller understanding of this particle path, to which this study is ultimately directed. It is anticipated that the detailed study of the data being developed will allow further elucidation of existing qualitative models. However, the development of a quantitative description of cyclone operation in terms of a mechanism is not currently feasible. The flow conditions in a cyclone are not fully understood even for a pure fluid, without the added complexity of the inclusion of multiple size-density particles. It is hoped that the development of the present data will also assist in an enhanced application of the hydro-cyclone and provide a base for further research. Some practical applications drawn from the data are suggested. Cyclone operations have been classified according

Jan 1, 1967

By Ralph Hultgren, Prodyot Roy

Manganese vapor pressures from 1250° to 1500°K were measured by conventional Knudsen and torsion-effusion methods in twelve Fe-Mn alloys with compositions from 9 to 80 at. pct Mn. The Knudsen re-sults agveed approximately with previous measurements found in the literature which indicated the solutions were nearly ideal. However, except for the higher manganese compositions, the initial torsion readings indicated much (up to 50 pct) higher vapor presszcres than the Knudsen method. These high readings decreased steadily with time. The results are interpreted as due to depletion of surface concentration of manganese during evaporation. Thus the initial torsion readings are the most nearly correct and Knudsen methods on alloys are to be regarded with suspicion unless it can be demonstrated that diffusion rates are rapid enough to replenish surface concentrations depleted by evaporation. For the lowest manganese contents and highest temperatures, depletion causes initial torsion readings to be too low. FEW thermodynamic data are available for alloys of the high-melting transition metals due primarily to experimental difficulties at the high temperatures involved. Measurement of vapor pressure is one of the most promising techniques to be applied to this problem. From the vapor pressure of a component of an alloy phase, its activity or its partial molar Gibbs energy can be directly calculated. From measurements over a sufficient range of temperatures and compositions the partial and integral Gibbs energies, enthalpies, and entropies may be determined through Gibbs-Duhem integration. For solid phases of variable composition, which commonly are found in alloys, measured vapor pressures are low because of depletion of the surface concentration of the more volatile component as it is selectively vaporized. Diffusion from the interior tends to restore the depleted concentration. The seriousness of the effect depends on the relative rates of diffusion and vaporization. Although depletion has been recognized as a factor,' direct measurements of its rate are lacking and quantitative estimates of its effect on measurements are uncertain. In the present work the vapor pressures above a series of Fe-Mn alloys have been measured by the torsion-effusion method. This method permits a measurement of the vapor pressure of manganese as soon as the sample comes to temperature and continuously throughout the run. The rate of decline of the apparent vapor pressure measures the rate of depletion and the torsion reading at zero time should be correct. At high manganese concentrations (70 and 80 at. pct Mn), the torsion reading remained nearly constant; surface depletion was negligible. There was a slow drop in measured pressure due to bulk loss of manganese from the sample. However, for lower manganese contents, especially at high temperatures, the depletion effect was considerable and the apparent vapor pressure decreased steadily with time. For these alloys the Knudsen method should give pressures which are too low. The measurement of pressure in the Knudsen method cannot be made until enough manganese has been vaporized to be weighable. The Knudsen result is therefore an integrated average between the initial and final vapor pressures. To verify this, conventional Knudsen measurements were also made with results in approximate agreement with previously published Knudsen measurements for these alloys. As expected, for the lower manganese contents the initial torsion readings of pressure were as much as 50 pct higher than the Knudsen. THE APPARATUS The apparatus, shown in Fig. 1, is capable of operating to temperatures up to 2000°K. A vacuum of 5 x 10"6 mm Hg can be maintained. Temperatures were measured to +3° by a W-Re thermocouple placed in the dummy cell, N. The torsion cell consisted of two alumina crucibles with holes in their covers. They were placed in the molybdenum holder shown suspended from the torsion wire. Rectangular torsion wires (1 by 4 mm) were found to have superior sensitivity and less residual distortion than circular (2-mm-diameter) wires. The precision of angular measurement was found to be *0.025 deg; the variation is no doubt due to temperature fluctuation and vibration. For the Knudsen experiments the alumina cell was set on the support, N. SAMPLE PREPARATION 800-g samples were prepared by melting together electrolytic iron and electrolytic manganese and pouring the melt into a water-cooled copper mold. Melting and pouring were done under a helium at-

Jan 1, 1965