Search Documents

By E. E. Mason

The Canadian National Railway system is completing construction of the first major tunnel in North America to use the coarse-aggregate (+ ½ -in.) shotcrete technique of primary support and lining. The tunnel was driven 29 X 20 ft in cross section, 10,760 ft long, passing under an industrial and residential area of Vancouver. With the exception of 1400 ft in soil (mainly impervious tills), the tunnel passes through a very young series of flat-lying sedimentary beds, to a large extent so incompletely consolidated as to fall apart on exposure. For a conventional steel-support system, it was estimated 8 WF, 28-lb steel should be used at 5-ft centers. Cost of erection including lagging would amount to $120 per linear ft of tunnel at 304 per lb. With 8-in. concrete cover on the steel, lining would cost $280 per linear ft at $82 per cu yd. Thus, minimum cost of support and lining would have amounted to $400 per linear ft. It is now estimated that at least 90% of the rock tunnel would have required support and 100 % required lining. Specified shotcrete support was 6 in. in the arch and 4 in. in the walls. Cost of this work was roughly $100 per linear ft. In addition, another $10-$12 per ft has been incurred in drainage and waterproofing wet areas and in measures to correct experimental and operational errors, thus finalizing the support as a lining (Fig. 1). The tunnel was driven three shifts five days weekly, no blasting being allowed by city ordinance between midnight and 7.00 a.m. A six-drill jumbo was used to drill a 10-ft round, 110 holes blasted three times daily. A 2-in. layer of shotcrete was applied to the newly blasted arch commencing within 45 min of blasting. This was done from a flying deck that extended over the muck pile from the jumbo (Fig. 2). Also during the mucking cycle, the preceding incomplete arch support was brought up to 6-in. specification. The walls were sprayed 4 in. thick during the drilling cycle (Fig. 3). The shotcrete machines and aggregate bins were mounted on the jumbo.

Jan 1, 1970

By T. D. Thomas

In this paper, major attention is given to misfires in mines where electric multiple shot-firing is the system used. Misfires are sometimes caused by one action or condition and at other times by a combination of two or more. They may be divided into two classes: (1) those caused by workers in the mines, (2) mechanical or manufacturer's causes. The second cause will be discussed first. Misfires Caused by Faulty Detonators The important part of an electric blasting cap, to the user where multiple shot-firing is done, as in the steep-pitch, thiek-vein, anthracite mines, is the bridge wire. In single shot-firing this factor is not apparent, but in mines where multiple firing is done any variation in the resistance of the bridge wire, where full or even rated battery capacity is required, will most likely cause a misfire. The reason for this is obvious. If the resistance in the bridge wires is not the same, some of the detonators will fire because of their greater comparative resistance. Variance in resistance of bridge wires is caused by a slight difference in the diameter of the bridge wire, also by a difference in the composition of the bridge wires. Again, where the bridge wires have become rusted, there will be a variance in resistance. About the year 1922, one of the large coal companies was greatly alarmed by the number of serious and fatal accidents caused by misfires. The general manager issued an order that these accidents must be greatly reduced, and if possible, entirely prevented. The officials at the mines had to determine the various causes of misfires and have them corrected. The rock contractors who use large quantities of 60 to 80 per cent. explosives and do all firing electrically were thoroughly instructed as to the proper methods of doing their work, and closer supervision was given to their work. The manufacturer's representatives stressed the importance of the use of galvanometers; accordingly these were purchased and used. Larger firing lines were installed under the supervision of a demonstrator of the company manufacturing the caps and explosives. However, misfires again occurred and it was evident that the source of the trouble was not wholly

Jan 1, 1930

By H. G. Botset

ANY information that will increase the accuracy of our knowledge of the conditions prevailing in petroleum reservoirs should be of direct value in the determination of the proper operating technique as well as in the estimation of reserves and of ultimate production. The obvious method of obtaining this information is by studying a sample of the reservoir rock and its contents. In any such study, the problem of primary importance and maximum difficulty is that of getting the core to the surface in such a manner that its original fluid content is undis-turbed, which has so far proved to be an impossible task. Though it might be rash to say this will never be done, it is certainly safe to assume that a method for the recovery of a core at the surface in its undisturbed original state may not be developed in the immediate future, and certainly will not be forthcoming without a great deal of costly experimentation. Therefore any information that may be obtained that will help to correlate the state of a core (its fluid saturation) at the surface with its condition at the time it was drilled should be of value to the petroleum industry. The experiments described in this paper were undertaken with the purpose of determining, if possible, any relationship that might exist between the saturation of a core at the surface and its original fluid content. No consideration has been given to the question of contamina-tion by penetration of drilling water, since this problem has been exten-sively studied by other investigators. 1-3 Furthermore, it was regarded as being outside the scope of the present experiments, which were con-cerned only with the effect of pressure reduction upon the liquid content of cores. In an experimental study of this sort involving a large number of variables, accurate control of all factors is very important. The essen-tial and obvious procedure is to vary systematically one factor or condi-tion while keeping all the others constant, which necessarily involves a rather protracted and sometimes tedious experimental program.

Jan 1, 1939

Lucien Eaton, Ishpeming, Mich. (communication to the Secretary *):—I began to use water Leyner drills at the Cliffs Shaft mine at Ishpeming, Mich., over four years ago, and now have over 20 in use. The ore in this mine is hard specular hematite, and is mined by the room-and-pillar system, the rooms being driven as breast stopes. For many years only 3 1/4-in. piston drills were used in the mine, each machine ordinarily being able to drill from 15 to 25 ft. of holes in a shift. In the hardest ground, however, it was often, impossible to drill more than 2 or 3 ft. in a shift. When water Leyner drills were used the footage drilled was materially increased, especially in the hardest ground, but it was found that in very hard ground the breakage of machine parts, and especially of drill steel, was very high. At this time round steel with lugs forged on the shanks was used, and most of the breakage occurred at or near the lugs. Many experiments were made in an endeavor to overcome this breakage, and it was finally decided to do away with the lugs altogether, and use hexagonal steel. Accordingly I designed a chuck to use hexagonal steel without luge, a tappet being interposed between the hammer and the shank of the' drill steel. The design of this chuck of the proper size for the No. 18 Ingersoll-Leyner drill is shown in Fig. I. The different parts are also shown photographed in Fig. 2. A is the barrel of the chuck, which revolves inside the front head. It is made of machinery steel. B is the bushing which screws into the front end of the barrel A, and in which the drill steel fits loosely. This is turned down from a steel casting, the hexagonal hole being cast and then broached out to the proper size. It is case hardened inside. C is the tappet, which fits smoothly inside A just behind the bushing B. It is made of " N " temper Crescent tool steel and is carefully tempered. D is the tappet ring, which prevents the tappet from being pushed back too far by the

Jan 1, 1914

By Hans W. Brodbeck

The main problem in tunneling without the use of explosives lies in the development of tools capable of continuous mechanical destruction of rock, resulting in a fragmentation which lends itself to a smooth, uninterrupted transportation of the broken rock away from the tunnel face. While all moles of U.S. design mainly achieve this by crushing the rock by means of "disk cutters" or "roller bits," a boring system based on the principle of cutting the rock came into being in Europe, whereby the rock is worked in a manner very similar to the milling of metals. For tunneling purposes, this principle was first developed by the late Austrian engineer Wohlmeyer. Between late 1962 and the spring of 1965, the first experimental machine was tested in a German coal mine, working in coal and shale over a distance of some 3000 ft, divided over two runs separated by a period of time to allow for equipment modifications. In 1964, a collaboration was started between Wohlmeyer and the Habegger engineering firm of Thun in Switzerland. The normal Habegger range of equipment consists of aerial ropeways, ski lifts, and certain tool machines, to which in later years have been added monorail passenger-transport systems. One of these was installed as the main mode of transport at the 1967 World Fair in Montreal. After taking over the Wohlmeyer patents, Habegger further developed the original cutting principle, aiming at more robust machines in order to be able to tackle harder rock. A first machine was built and tested at a site near Thun in sandstone averaging 17,000 psi compressive strength and limestone of 25,000 psi. In May 1966 this machine was delivered to Japan for the boring of a pilot tunnel for the Honshu-Hokkaido railway connection under the sea. A second machine, incorporating many improvements based on experience gained with this first mole, was built during 1966 and tested in the same limestone as mentioned previously (25,000 psi), before being installed to bore the head race tunnel of the Julia hydroelectric power scheme near St. Moritz, Switzerland, in the early summer of 1967 (Fig. 1 ) .

Jan 1, 1970

All the TECHNICAL PUBLICATIONS and CONTRIBUTIONS published in 1938 are available at Institute headquarters, unless otherwise noted. They are also on file in many public, university and technical libraries and, when so indicated in the list, may be found in the TRANSACTIONS. TECHNICAL PUBLICATIONS in Classes A-Metal A-Lining, B-Milling and Concen-tration, H-Industrial Minerals, and I-Mining Geology are distributed in MINING TECHNOLOGY, which is issued every other month. Technical Publications in Classes C-Iron and Steel Division, D-Nonferrous Metallurgy and E-Institute of Metals Division are distributed in METALS TECHNOLOGY, which is issued twice quarterly. TECHNICAL PUBLICATIONS ill Class G-Petroleum Division are distributed in PETRO-LEUM TECHNOLOGY, which is issued quarterly. TECHNICAL PUBLICATIONS in Classes F-Coal Division, .l-Mineral Industry Education Division, K-Mining Administra-tion, and L-Geophysical Methods of Exploration are issued as separate pamphlets. All Institute member is entitled to one copy of any TECHNICAL PUBLICATION or CON-TRIBUTION. Copies of TECHNICAL PUBLICATIONS listed have been mailed to members of the Institute according to their registration by classes. CONTRIBUTIONS and other TECHNICAL PUBLICATIONS will he sent upon request. A member may purchase an additional copy of a TECHNICAL PUBLICATION or a CONTRIBUTION at one cent. a page; in minimum charge, 256. If the TECHNICAL PUBLICATION has been published in METALS TECHNOLOGY, MINING TECHNOLOGY or PETROLEUM TECHNOLOGY, the number of either magazine containing it will be supplied at the sae cent a page (minimum charge, 25¢) rate for the particular TECHNICAL PUBLICATION requested. Nonmembers may purchase any CONTRIBUTION or a TECHNICAL PUBLICATION Of the F, J, K, or L classes at the same rate, butt the nonmember price per copy for METALS TECHNOLOGY, MINING TECHNOLOGY or PETROLEUM TECHNOLOGY is $1. TECHNICAL PUBLICATIONS (Separate pamphlet form), $2 per annum; Canadian and foreign postage 50 cents extra. METALS TECHNOLOGY, $7 per annum; Canadian and foreign postage 50 cents extra (Iron and Steel Division and Institute of Metals Division ferrous and nonferrous papers). MINING TECHNOLOGY, $6 per annum; Canadian and foreign postage 50 cents extra (metal mining, milling and concentration, Industrial Minerals Division, and mining geology papers). PETROLEUM TECHNOLOGY, $4 per annum; Canadian and foreign postage 50 cents extra.

Jan 1, 1938

By J. A. Fulton, A. B. Foote

Gold was discovered in the Sierra Nevada by J. W. Marshall on Jan. 2, 1848. The town of Grass Valley soon sprang up and contained several stores in 1849; but the population of the town has always reflected the fluctuations in quartz mining. Gold-bearing quartz was found on Gold Hill in September 1850, and in the next two years most of the quartz-bearing veins in the vicinity were located. At first, the quartz was crushed in mortars with spring poles; the IIuff Co. took out $20,000 in this manner during the winter and spring of 1851. The first mill was put up in January, 1851. In 1866, there were in Grass Valley 248 stamps, crushing 71,420 tons of ore with an average yield of $30 to $35; in Nevada City, there were 142 stamps, crushing 14,200 tons, with an average value of $25. Rut in 1918, only two properties in this region, the Empire and the Korth Star, were producing Since then, there has been a revival of mining in the district and the following properties are being opened up: The Golden Center. Grass Valley Gold Mines Co.. Idaho-Maryland Mines Co., while the Su1tana is kept unmatered and work is going on in a half dozen mall propertics Mining Claims At the first meeting of miners in Grass Valley, Jan. 13. 1851, a plot :30 by 40 ft. was allowed for a claim, the boundaries in all cases being perpendicular. In 1852, the quartz miners in Nevada County deeided that "each prospector shall hereafter be entitled to 100 ft. on a quartz ledge or vein and the discoverer shall be allowed 100 ft. additional. Fach claim shall include all the dips, angles, and variations of the vcin." This rule was in force until replaced by the Federal mining laws of 1872; these allowed quartz claims to be 1500 ft along the vein, with all the dips, spurs, and angles, and to have a width of 600 ft. The holdings of the principal companies consist of these early patented mining claims; standard claims, as authorized by the Act of 1872, both patented and unpatented; agricultural tracts, both patented and

Jan 1, 1927

By C. V. Millikan

When a flowing oil well is being drilled in with cable tools, it is difficult to determine when an additional streak of pay sand is drilled. By placing a gas meter on the gas-release line from the oil and gas separator, any increase in volume of gas that comes with oil production is recorded. In addition to the better knowledge of sand conditions, these data are a valuable aid in determining the size and depth of shots, plugging off water, and estimating ultimate production. The meter also gives a record of operation while the well is drilling in; and if allowed to remain on the well after completion will give information that may lead to a more efficient recovery of the oil from the sand. A VERTICAL cross section of any oil sand will show great variation in porosity and oil content. In some sands, the entire thickness contains oil, the variation being only the degree of porosity or oil content, but more often the pay streaks are distinctly separated by shells or barren streaks. These pay strata vary in number and may be thin or thick. The total thickness of the sand may be several tens of feet while the part containing oil may be only 1 or 2 ft. thick. The amount of production is not proportional to the thickness of the sand but rather the thickness of the pay streaks. If the total thickness of the sand or the amount that can be drilled is small, or if the initial production is small, the depth at which each stratum of pay is encountered can be determined sufficiently accurately for all present economic purposes. However, when drilling through sand of considerable thickness, giving large initial production, especially where conditions necessitate that the production go through the same gas trap with that from one or more wells already producing, it is difficult to determine the depth at which the pay strata are encountered even accurately enough to guide the placing of shots, and small pay streaks are apt not to be recognized at all.

Jan 9, 1925

By L. J. W. JONES, B. H. Bennetts

THE removal and disposition of large quantities of slag from blast-furnaces is a question of great importance in the design of works, and various methods have been devised, from time to time, in order to take the best advantage of local conditions. In blast-furnaces treating copper-ores or lead-ores, it is necessary to use a fore-hearth, or matte-settler, in order to collect, if possible, every particle of valuable matte which, otherwise, would be carried away with the out-flowing slag. In all of these cases, the slag overflowing from the fore-hearth is caught in pots and then conveyed to the dump. If the slag is of no value and the necessary water-supply, grade and dumping-space be available, the disposal of the slag by granulation is by far the cheapest and best method. It involves a minimum of labor, both at the furnace and at the dump; and it permits a continuous outflow of slag from the furnace- or settling-pot, thereby avoiding frequent tapping and plugging. When the conditions of water-supply, grade and dump-area will not permit slag-granulation, there are three other methods in common use. Large steel or cast-iron pots, or ladles, supported by trunnions on heavy cars which are moved by steam-, air-, or electric locomotives; some type of mechanical conveyor; and small pots or buggies moved by hand. The pots on the slag-cars are generally circular or oval in shape, and each one contains from 15 to 40 or more en. ft. of molten material. The mechanism for tipping them is more or less elaborate; and, as a general rule, the slag is dumped alongside, and quite close to, the track. They are more or less costly to construct and to keep in repair, and, in order to use them to best advantage, it is necessary to have a good elevation of track above the dumping-ground; furthermore, the rails must be of heavy weight, and well-supported on heavy ties. Other disadvantages of the slag-pots are-1, that the slag cannot be removed continuously

Mar 1, 1905

By John McCoy, Edward Thimons, Kenneth Heller

As the working levels in domestic mines are developed to greater depths and work areas move further from the shafts, maintaining a safe and healthful working environment becomes more difficult. Increased temperature and humidity at greater depths becomes first a factor in productivity and then a threat to the miner's safety. Initially, a miner might develop listlessness leading to reduced productivity and reduced alertness. Continued overexertion can lead to heat stroke and possibly death. Mine ventilation engineers, therefore, must not only provide clean air to work areas, but also must provide cooled air. The following article describes the United States Bureau of Mines (USBM) and Foster-Miller's successful development of a high performance, low maintenance direct water to air contact heat exchanger for mine cooling. While heat problems frequently do not develop until mining operations descend below sea level, problems will arise any time mining penetrates high temperature rock. Hot fissure water will increase the severity of the situation, causing increases in wet bulb temperature - the temperature to which perspiring miners reject metabolic body heat. All energy expended in mining adds to the heat load which must be absorbed by the ventilation air. Just when the cooling capacity of ventilation air is needed most, adiabatic compression (autocompression) of air descending the shaft raises air temperatures 1.3g°C (2.5'F) to 2.94"C (5.3OF)/305m (1000 ft) depending on humidity. Increased temperatures decrease the ability of the air to absorb heat from the mine, and work area temperatures rise. Once forced ventilation air can no longer maintain safe work area temperatures, refrigeration methods must be employed. Many mines now use cooling coils for this purpose. A cooling coil uses refrigerated mine water to cool the air by passing the air through banks of copper tubing filled with cold water. Heat from the air is transferred to the water through the pipe with the aid of fins. Conventional water to air heat exchangers prove troublesome for many mines be- cause of the high levels of dust that are encountered, causing these exchangers to operate at relatively low efficiencies. A more satisfactory approach to work- place cooling is desired - one that offers reduced maintenance and increased cooling efficiency.

Jan 1, 1982

By B. K. Asdell

Crude kaolin exhibits a wide particle size range in which kaolinite is the predominant mineral. Bene-ficiation by wet processing produces high-brightness white pigments. The wet processing techniques peculiar to kaolin beneficiation are emphasized in this article in some detail. Included are discussions of long-distance pipeline transportation, centrifuga-tion, flotation, spray drying and shipment as 70% solids slurry. Georgia, a state seldom considered to be an important mineral producer, has one surprising feature — it is the nation's largest producer of kaolin. Kaolin is a highly important raw material in the paper, rubber, ceramic whiteware, paint and chemical industries. In 1965, more than 2.7 million tons of kaolin were produced in this state, a 150,000-ton increase over the preceding year, and production continues to climb. Strictly defined, the term "kaolin" applies to a group of hydrous aluminum silicates in which kaolinite is the predominant mineral. Kaolinite is inherently white, non-abrasive, chemically inert, and of a very fine particle size, ranging from sub-micron to 40-microns equivalent spherical diameter. An electron-micrograph of kaolinite is shown in Fig. 1. The particles finer than about 2 microns are thin, elongated plates, hexagonal in outline. The larger particles, coarser than 2 microns, are predominantly vermicular in outline with a foliated structure. Table I shows a typical chemical analysis of commercial, wet-processed kaolin compared to pure kaolinite. The sedimentary Cretaceous deposits of the Coastal Plain are the source of most of the kaolin produced in the Southeast. These deposits are of relatively high purity, and it is not uncommon to find the clays running greater than 90% kaolinite. Beneficiating plants using wet processing techniques are most numerous in an area within about 50 miles east of Macon, Ga., in a band approximately 15 miles wide. Kaolin may vary widely in quality from one deposit to another, or within the same deposit. The qualities critically examined are brightness index as measured by reflectance, viscosity of water suspensions, bleachability and particle size distribution. Crude kaolin always contains sand and mica in varying amounts, along with small amounts of many other minerals. These are classed collectively as "grit" because; they are generally coarser than 325

Jan 1, 1968

By George A. Roberts, Robert F. Mehl

When austenite first forms from aggregates of cementite and ferrite, it is not homogeneous.' This inhomogeneity, consisting of both undissolved carbide and carbon concentration gradients, has a profound effect upon the characteristics of the austenite-pearlite reaction. The rate of formation of pearlite is increased by the presence of inhomogeneities2,3 and because of this (when the inhomogeneity is sufficiently pronounced) the hardenability of the steel is reduced.4,5 In addition to this kinetic effect, inhomogeneities will cause the direct formation of spheroidite from austenite at temperatures just below the Ael.6-11 The present report attempts quantitatively to evaluate the effect of inhomogeneity upon the rate of the austenite-pearlite reaction, presents a method of determining the austenitizing cycle necessary to obtain "practical homogenization," and considers the effect of inhomogeneity on hardenability. Effect of Inhomogeneities on Reactions Near Ae1 Few quantitative data are available representing the effect of undissolved carbide or of carbon concentration gradients upon the rate of the austenite-pearlite reaction. In procuring such data it is necessary to separate the effect of undissolved carbide from that of grain size, and this is not an easy task. The solution of carbide is always accompanied by an increase in the grain size, both effects contributing to the retardation of the reaction rate. It has been possible to make this separation and to obtain data that are independent of the grain size by the use of steels that differ only with respect to their tendency toward grain-coarsening. Steels C and D in Table I are such steels. These steels have been studied previously ;l,2,12 they differ only with respect to deoxidation practice; C was deoxidized with silicon while D, teemed from a portion of the same heat, was deoxidized with additional auantities of aluminum in the mold. C therefore is what is normally termed a "coarse-grained steel" and D is a, "fine-grained steel." These steels can be compared at the same grain size by heating c to a low temperature and heating D to an elevated temperature, producing a structure of austenite plus residual carbide in the former while forming homogeneous austenite in the latter; in such

Jan 1, 1943

By George A. Roberts, Robert F. Mehl

When austenite first forms from aggregates of cementite and ferrite, it is not homogeneous.' This inhomogeneity, consisting of both undissolved carbide and carbon concentration gradients, has a profound effect upon the characteristics of the austenite-pearlite reaction. The rate of formation of pearlite is increased by the presence of inhomogeneities2,3 and because of this (when the inhomogeneity is sufficiently pronounced) the hardenability of the steel is reduced.4,5 In addition to this kinetic effect, inhomogeneities will cause the direct formation of spheroidite from austenite at temperatures just below the Ael.6-11 The present report attempts quantitatively to evaluate the effect of inhomogeneity upon the rate of the austenite-pearlite reaction, presents a method of determining the austenitizing cycle necessary to obtain "practical homogenization," and considers the effect of inhomogeneity on hardenability. Effect of Inhomogeneities on Reactions Near Ae1 Few quantitative data are available representing the effect of undissolved carbide or of carbon concentration gradients upon the rate of the austenite-pearlite reaction. In procuring such data it is necessary to separate the effect of undissolved carbide from that of grain size, and this is not an easy task. The solution of carbide is always accompanied by an increase in the grain size, both effects contributing to the retardation of the reaction rate. It has been possible to make this separation and to obtain data that are independent of the grain size by the use of steels that differ only with respect to their tendency toward grain-coarsening. Steels C and D in Table I are such steels. These steels have been studied previously ;l,2,12 they differ only with respect to deoxidation practice; C was deoxidized with silicon while D, teemed from a portion of the same heat, was deoxidized with additional auantities of aluminum in the mold. C therefore is what is normally termed a "coarse-grained steel" and D is a, "fine-grained steel." These steels can be compared at the same grain size by heating c to a low temperature and heating D to an elevated temperature, producing a structure of austenite plus residual carbide in the former while forming homogeneous austenite in the latter; in such

Jan 1, 1943

By H. H. Lowry

SCIENCE attracts the attention and interest of an individual or an industry in general only in proportion to the apparent direct application to its immediate welfare or benefit. Engineering accomplishments, as applied science, therefore receive more recognition than the scientific discoveries on which they are based. Even self-evident truth needs endless repetition before recognition: engineering as applied science cannot advance beyond the science on which it is founded. Scientific research, and discovery, is sometimes forced by the limitations recognized by those active in its development for the use of society and industry and sometimes results from an apparently superficially illogical curiosity about natural phenomena. Research has received inadequate support except in industries born in the laboratory, the chemical and electrical industries, from which many lessons might well be drawn by their elder associates. The rapid growth of these industries has been largely due to close cooperation of scientists and engineers. Most rapid advance is made when the research worker and the engineer keep in close touch with each other's ideas and problems. Many of the developments of modern industry are based on dis-coveries buried for years in scientific journals because the "time was not ripe" at their discovery. The situation with regard to utilization of coal is quite the opposite. The fundamental facts in regard to the scientific aspects of the problem of developing the energy from coal are scarcely known. The engineer, without much scientific cooperation, has accom-plished much in increasing the number of kilowatt-hours per pound of coal from 0.31 in 1919 to 0.69 in 1934, in increasing the 1000 gross ton-miles of freight hauled from 6.1 to 8.3 per ton of coal in the same period, in fuel economy in production of coke, and in developing the production of motor fuel in Germany and England by hydrogenation of coal. This lack of scientific research on the utilization of our most important natural resource, coal, has been due undoubtedly in large part to the reluctance of investigators to study the interrelationships involved in, the complicated processes in which coal is used. These complexities are made

Jan 1, 1936

By O. E. Kiessling

THE present system of competitive exploitation of oil pools results in losses, both of petroleum and of profits. Under a competitive system the owner produces or withholds his product according to the price, which reflects the demand, but in the pe-troleum industry the producer does not have complete control over the expansion and contraction of his out-put. Under a series of court decisions, reviewed in detail in the paper, petroleum is not covered by- the general theory of English common law that the owner of land owns everything from the center of the earth to the sky within the areal limits of his property, but is considered to be his only when he has reduced it. to possession, which he can only do by taking it out of the ground. If A can obtain possession of the petro-leum which is beneath the property of B without tres-passing on B's property he commits no legal wrong and B has no defense except to get it into his (surface) possession before A takes it. No one would expect an. owner under such a system to forego the possibility of securing some oil from his property in order to in-crease the ultimate production of the pool. The pe-troleum industry. should offer a constructive program, that will eliminate losses and protect the interests of individuals as far as possible. If improved methods of oil recovery can be applied the quantity of petroleum recovered might be double or even treble the amount recovered by ordinary procedure. But increased recovery is not the only benefit from pool development. In brief, the following advantages can be claimed for unit operation: 1. Saving in development and operating costs. 2. Less danger of damage to the fields by defective wells. 3. Development is better gaged to fit market demand and to effect the most efficient recovery of oil. 4. More oil, gas, and gasoline can be marketed. 5. By regulating pressures, recovery .of oil and gas will be greater and the wells will flow longer. Reagan County (Big Lake), Rainbow Bend and Cabin Creek are examples of longer life of pools thus obtained.

Jan 11, 1927

By E. Luttgen

The substance referred to in the title is the artificially prepared basic carbonate of magnesia, a compound of the carbonate with the hydroxide. It is the "block-magnesia " of commerce, the magnesia alba of the pharmacist. Its composition, though somewhat indefinite, may usually be expressed by the formula : 4MgCO3,Mg(OH)2, 5H2O; it is found to vary slightly with the details of the method of preparation. This substance has been employed recently with much reported success, as a non-conductor of heat. It is moulded to form coverings suitable for steam-pipes and their fittings and sectional jackets for boilers and cylinders; it is furnished also in forms suitable for lining refrigerators, walls and roofs of buildings, fire-proof safes, etc. It was with a view of ascertaining the efficiency of this material as a non-conductor, or, rather, its relative efficiency among the various non-conducting materials in use, that the writer made the experiments about to be described. A block of magnesium carbonate or magnesia alba exhibits some interesting physical qualities. It is a smooth, white, close-grained solid, in outward appearance resembling a block of Paris plaster. It possesses the lightness of cork, the porosity of sponge, and withal a degree of firmness and strength that, in view of its levity, is quite remarkable. To examine more closely the properties of this substance, a number of 1-inch cubes were sawed from the commercial block-carbonate, also some bricks, that is, blocks measuring accurately 2 x 4 x 8 inches, the dimensions of an ordinary brick. The cubes weighed from 2.2 to 2.7 grammes, the bricks weighed 140 to 175 grammes (5 to 6 ounces). The bricks were carefully measured and weighed, and placed in vessels containing distilled water, in which they became gradually submerged, owing to the displacement by water of the air inclosed in the structure of the magnesium carbonate. After twenty-four hours the blocks were removed from the water, dried superficially by contact with filter-paper and weighed. From the increase in weight, the volume of the water absorbed, and consequently that of the air displaced by it, were obtained. For example: a block which when dry weighed 155

Jan 1, 1887

By John Chipman, K. C. McCutcheon

To a very large extent the quality of a mild steel ingot is determined by the manner in which it is poured into the ingot mold and its behavior during the first few minutes after it has been poured. The formation of the solid rim of metal around the periphery of the mold, the effervescent action of the liquid steel within this solidified rim and the upward or downward movement of the metal level are indications of what is going on beneath the surface of the liquid metal, especially at the interface at which solidification occurs. Observation of this "rimming action" enables an experienced observer to predict the thickness of the sound skin of the ingot and the location and extent of cavities or "blowholes" caused by entrapment of gases. The control of rimming action at the hands of a skillful steel pourer is a vital part of the control of quality in mild steel sheet, and the behavior of the liquid steel during the rimming period is a useful criterion of the melting and refining practices employed in the open hearth. The behavior of rimming steel during solidification depends primarily upon the evolution of gases from the molten metal and it is therefore a problem of considerable interest to determine the nature and amount of the gases evolved. A number of attempts to determine either the amount or the analysis of the evolved gases have been reported. Klinger,1 in 1925, analyzed the gases extracted from rimming, semikilled and killed steel ingots and found that the chief constituent of the rimming gas was carbon monoxide. The relatively large amounts of nitrogen reported in his first few samples may have been due to incomplete removal of air from the gas-collecting mechanism. McKune2 reported similar studies of rimming ingots from which surprisingly large proportions of nitrogen and hydrogen were evolved. Ameen and Willners3 determined both the amount and composition of gases extracted from unkilled ingots with the aid of diminished pressure. . Their ingots weighed only 80 kg. (176 lb.) and apparently were solid within two or three minutes, so that their

Jan 1, 1938

By J. B. Austin, R. L. Rickett

MEASUREMENTS Of the rate of decomposition of austenite at constant temperature are commonly represented by plotting the percentage transformed on linear coordinates against time on either a linear or a logarithmic scale, a method that yields a curve that in shape resembles an integral sign (Fig. 1). A graph of this kind is not always convenient because extrapolation to the beginning or end of the transformation, or even interpolation, may be uncertain unless there are a large number of observations, which seldom happens; furthermore, the degree of consistency of a set of measurements is difficult to judge from such a curve. It is desirable therefore to find some mode of plotting, or even better to find a standard variety of graph paper, that gives a straight line instead of the integral shape. The straight line has many advantages; the number of readings required to fix the position of the curve is greatly reduced, interpolation is easy and rapid, extrapolation can be carried out with greater confidence and, finally, the consistency of the measurements is readily estimated from the scatter of the points. The last advantage is particularly valuable when the data are obtained by direct microscopic examination alone, because they are influenced by the skill of the observer in estimating the relative size of areas, possibly also by undetected inhomogeneity of the specimen. A search for ways of representing the observations as a straight line yielded two methods which are described in this paper. The paper also includes an account of some interesting relations brought to light in applying these methods to the available experimental data. Usually the best way to derive such a method of plotting is to base it on established principles of chemistry and physics, as has been done, for example, for the temperature variation of the equilibrium constant of a chemical reaction. But so little is known of the mechanism of the decomposition of austenite, and so little is available in the way of well established background for changes of this kind, that it is simpler to rely upon purely empirical means. The general plan therefore is to study existing data with a view to finding some function of the direct observations that will

Jan 1, 1938

By Wm. R. Webster

THIS is a contribution for the proposed new discussion on the physics of steel. The former discussion on the subject started with the consideration of five papers presented at the Chicago meeting in 1893, and continued for several years. The Suggested Lines of Discussion, prepared by Doctor Howe, covered a wide field and added greatly to the success of the work. Naturally, the first step in a new discussion will be to remodel and bring up to date the old Suggested Lines of Discussion so as to embody all the important advances in the metallurgy of steel that have a bearing on the physics of steel and keep the papers and discussions within the field of work undertaken. This paper will be devoted to the practical application, in rolling steel, of the effects of carbon, phosphorus, and manganese on its tensile strength, with some suggestions on further research work. Dr. J. E. Stead, in his paper Influence of Some Elements on the Mechanical Properties of Steel,1 gave a complete review of all that had been done during the past thirty years. He gave full credit to all investigators who worked on these lines, also their results, with his views on same, and in many cases his own results. All of this data and much new valuable information were put in convenient shape for reference and study. To do this required a great deal of work, which is fully appreciated by the steel manufacturers and investigators. The variations in the values given by the different investigators for the increase of the tensile strength of steel for each 0.01 per cent. of carbon, phosphorus, and manganese were largely due to the steels they worked on, the large or small variations in the amount of the elements present, and the omission to take into consideration all the factors, from the blast furnace through to finished rolled material, that affect the character of the steel. For instance, a poorly made dirty steel requires considerably more carbon to give the same ultimate strength than a well-made clean steel with the same phosphorus and manganese content.

Jan 3, 1921

By Arthur Braid

The war has caused an increasing scarcity of phosphorus and its well known alloys with copper and tin. At the same time, the production of brass and bronze, nickel-silver, cupro-nickel, and other non-ferrous alloys, has considerably increased. The manufacturers of these products had therefore to secure other materials which would serve their purpose; principally that of a deoxidizer, which could be obtained promptly and regularly. Fortunately these materials, pure carbon-free manganese metal and manganese-copper alloy, were not hard to find—in fact, they were never lost. Manganese in various forms has been used in Europe for more than a century; in this country, however, when manganese was first used, and indeed for a long time thereafter, it was consumed mainly in the manufacture of manganese-bronze. Many foundrymen at that time used manganese-copper with the same freedom as phosphor-copper. Although iron enters into the composition of certain grades of bronze, it is very detrimental to non-ferrous mixtures in general; consequently ferromanganese is not applicable, and therefore pure manganese metal, or the alloy of manganese and copper, technically free from iron and other impurities, is now being generally used. The following are the principal elements having an affinity for oxygen: 1, Sodium. 2, Potassium. 3, Calcium. 4, Strontium. 5, Barium. 6, Magnesium. 7, Aluminum, 8, Phosphorus. 9, Silicon. 10, Manganese. 11, Iron. 12, Zinc. 13, Lead. Each metal has its natural flux, or deoxidizer, in the form of a metal or non-metal which will alloy with it, and has a strong affinity for oxygen. For example, phosphorus, as is well known, acts very beneficially in copper alloys that contain tin. Within the last few years, and particularly since the war began, the .great value of mangancse in nickel alloys has been demonstrated, and one by one the manufacturers of these products have adopted its use. While manganese has not so strong an affinity for oxygen as magnesium, aluminum, or silicon, it is nevertheless sufficiently powerful to reduce any oxide of nickel, copper, or zinc that may be present in the nickel alloy to be purified.

Jan 1, 1919