Search Documents

By F. R. Cattoir, R. W. Kimball, C. T. Anderson

ONE of the principal impurities in all steels is sulphur. Sulphur-bearing, manganese-free steels exhibit hot shortness. Manganese is added to steel to improve the hot-working properties. If no sulphur were present in steel, it is probable that hot shortness would be nonexistent. This paper is the first of a series to be issued by this Laboratory reporting the measurements of hot forgeability tests and the physical properties of Fe-C alloys to which additions of various alloying elements have been made. The present paper describes the results- obtained by the addition of varying amounts of sulphur to Fe-C alloys. To obtain control over residual elements in the various charges melted in the arc furnace, it was considered advantageous to use sponge iron from one source as the melting stock rather than scrap metal having an unknown history. Small amounts of unwanted alloying elements might be introduced into the charge when scrap was used, thereby influencing the results of the various heats. A sponge iron having a high silica-lime ratio was used. Ore from Sunrise, Wyo., had been reduced to sponge iron and briquetted at the Bureau of Mines sponge-iron plant at Laramie, Wyo. The briquettes were 5 in. in diam and 2 to 3 in. in thickness, and weighed about 10 lb each. The chemical analysis of the sponge iron is as follows: C, 0.67 pct; Mn, 0.10; SiO2, 4.75; CaO, 1.4; P, 0.044; S, 0.72; MgO, 0.4; A12O3, 1.1; total Fe, 87.5; Fe metallic, 79.2; and reduction, 90.5 pct. Where a reducing agent was required, crushed graphite electrodes usually were used. The charcoal available contained 0.20 pct S. An analysis of the available coke showed it to contain 0.70 pct S. Where high sulphur heats were required, elemental sulphur additions were made to the ladle. Limestone of good quality was obtained locally and had the following analysis: CaO, 53.7 pct; MgO, 0.8; ignition loss, 42.4; R2O3, 0.2; SiO2, 3.0; and P2O5, 0.014. Melting Procedure Sponge iron was melted to produce metal stock for the experimental alloys in a silica-lined, three-phase, direct-arc, size ST, Moore Rapid Lectromelt furnace with a 500 kva rating. Fig. 1 shows this furnace installation. About 25 tons of sponge iron was melted in 75 heats, averaging 927 lb of sponge iron to the heat. An addition of carbon was required to complete the reduction of a portion of the iron oxide remaining in the sponge to prevent high losses of iron oxide in the slag and a low carbon content in the resulting metal. As reducing agents in preparing the melting stock, charcoal, coke, and a carbon product resulting from the thermal decomposition of natural gas were used. The quantity varied from 20 to 60 Ib per furnace charge, with an average of 38 lb. An average analysis of the metal obtained gave 0.52 pct C, about 0.01 pct Mn, 0.070 pct P, and 0.092 pct S. The average yield of metal was 647 lb with 241 1b of slag, the sponge-iron recovery being 70 pct. The metal obtained in melting the sponge iron was cast into pigs weighing about 20 lb each to facilitate recharging into the furnace for further refining. The pouring of the pigs is shown in Fig. 2. The average power consumption for the production of the 24 tons of metal obtained was 1704 kw-hr per ton.

Jan 1, 1954

By I. Zaplatynskyj, G. C. Kuczynski

SINCE the excellent studies of metal powder compaction executed by Kamm, Steinberg, and Wulff, no work on the subject has appeared in the technical literature. Kamm et al. were the first to investigate quantitatively the distribution of density in a powder compact, as a function of pressure, height and diameter of the die, powder particle size, etc. For this purpose they devised a very ingenious method. They inserted a thin lead grid into a die and then filled the die with powder. During cold pressing, the lead grid -moved downward. Due to its deformability it followed closely the downward descent of the adjacent powder. The die was then radiographed and, from the deformations of the grid openings measured on the radiographs, the density in the vicinity of each opening was evaluated. Their findings led them to the conclusion that the friction on the side walls of the die is a major controlling factor of the density distribution inside the cold pressed powder compacts. However, it is difficult to conduct tests similar to those of Kamm, Steinberg, and Wulff in a processing plant laboratory, which usually lacks the necessary expensive radiographic equipment. The purpose of this note is to describe a method which makes it possible to determine the density distribution in green powder compacts with the same accuracy as the lead-grid method but which is far simpler and faster and requires only standard laboratory equipment. Instead of using a lead grid, the hardness at selected points of the sectioned compact is determined. If the relationship between hardness and density is known the density distribution is readily obtained. This relationship is easily found from measuring hardness and densities of thin compacts. In such compacts the density, for all practical purposes, is constant throughout. The method was tested on a Plast nickel powder, grade FlA-A20, kindly supplied by Plast Metals Co. Thin compacts (height to diameter ratio 0.2) were pressed in a single action cylindrica1 die at various pressures. The density of the compacts was determined by weighing and by measuring the height and diameter with a micrometer. Subsequently the Rh hardness was determined. Up to ten readings were taken on each specimen. The difference in hardness readings on each compact was never greater than three corresponding to about 0.1 g per cu cm uncertainty in density. By varying the compaction pressure of the samples, a whole scale of densities was obtained allowing construction of a set of density-hardness calibration curves. To test the method several compacts of different height were pressed under varying pressures. Die walls were always well lubricated. After pressing, the compacts were mounted in bakelite and halved by grinding, and hardness readings taken along the diameters of the specimens. The distance between adjacent indentations was about 2.5 mm. After hardness readings were translated into densities, contour maps of densities of the compacts were prepared. One of them is reproduced in Fig. 1. The areas encompassed by the curves are labeled with numbers representing the density in g per cu cm of those regions. In Fig. 2 the same results are re-plotted to emphasize the radial density changes at various depths. The results thus obtained confirm the findings of Kamm, Steinberg, and Wulff kentioned previously. They are recapitulated here briefly. 1—The densest part of a compact pressed from one side is at the outer circumference at the top and the least dense part at the bottom, at the outer circumference. Figs. 1 and 2 show this clearly. 2—The density near the cylindrical surfaces of the compact decreases uniformly with height from top to bottom. 3—The density variation increases with the height to diameter ratio. References R. Kamm, M. A. Steinberg, and J. Wulff: Trans. AIME (1941) 171,'R. p. 439 ;MetaLs Technology (February 1941). R.p. Kamm, M. A. Steinberg, and J. Wulff: Trans. AlME (1949) 180, 2R.P. 694; MetalS Technology (December 1948).

Jan 1, 1957

By T. A. Rickard

The writing that is effective is woven with a fine texture into an agreeable pattern; it is free from knots, loose threads, and stray fluff. The instrument that weaves this literary fabric, whether it produce a homely sock or a lordly tapestry, a simple story or a learned 'Itreatise, is a disciplined intelligence, as sure as a steel needle, as precise as a swift loom. The simile breaks down at this point, for the product of the pen is instinct with the human spirit and therefore transcends in beauty anything made by a mere machine. If words are to be woven into eloquent meaning, they must be well knit. Upon the relation of words to each other and of groups of words to other groups, known as phrases, clauses, and sentences, depends the success of writing as a means of trans¬mitting thought from man' to man. To be understood beyond question, you should know not only what your words denote but how to build your sentences; you must not only choose your words aright but construct your sentences properly. A sentence is a combination of words that makes complete sense; it says something about something. ' A clause is a subordinate sentence or a sentence within a sentence. A phrase is a group of words without a predicate; it makes sense, but not complete sense. For example: I shall wait for a few minutes before I go home: The whole statement is a sentence; "I shall wait" and "before I go home" are clauses; "for a few minutes" is an adverbial phrase. The orderly arranging of words and of combinations of words is called `syntax'; and from the original Greek form, ouvaeis (suntaxis), is derived the Greek name for an editor,

Jan 1, 1931

By WILLIAM E. NEWNAM

THE molding and loading of pig lead has, in the past, been accomplished mainly by the strong arm method and, as the pigs are usually loaded directly into the cars, it has been a hot and laborious task. Of late years it has been difficult to obtain men willing to perform such labor and the need has been felt for loading and molding machinery which would eliminate all manual handling of the hot pigs and which would be sufficiently compact to permit of installation in existing plants with little or no

Jan 1, 1924

By T. W. Atkins

ATHOUGH the magnesium industry in this country is about thirty years old, not until American industry began to amaze the rest of the world and confound our enemies with the extent and variety of our war production did the industry begin to come into its own. At the outset of the war, only three companies were producing and fabricating magnesium in this country. Today, about sixty companies are producing, casting, forging, extruding, rolling, and stamping this lightweight champion of metals. Experience in alloying, processing. and fabricating the metal gained during the war years is now being translated into hundreds of civilian peacetime applications. In no sense should magnesium be considered as a substitute for other metals. It has come into popular favor because If many unique properties in addition to is being the lightest known structural metal. These attributes are toughness, igidity, corrosion-resistance, and the ease with which it can be machined and worked. Magnesium is the third most abundant element in nature. Sea water, magnesite,

Jan 1, 1946

By V. Niemitz

Approximately 30 miles east of Chicago on the southern shores of Lake Michigan stands Bethlehem Steels newest fully integrated steelmaking facility-the billion dollar Burns Harbor plant. The first phase of what will ultimately be the most completely integrated and flexible materials handling system for a steel mill in the western hemisphere is now complete.

Jan 1, 1970

By E. B. BESSELIEVRE

THE great work of Gorgas in stamping out yellow fever in Panama during the construction of the Canal was one of the chief factors contributing to the ultimate accomplishment of the task, two previous attempts having failed largely through the demoralization of workers by epidemics of contagious diseases. Mining camps, rapidly constructed during the boom days of the rushes to new fields, have been frequent sufferers from typhoid when, as so often used to be the case, little or no attention was given to bacterial examination of the water supply or to the method used for disposing of the sewage.

Jan 1, 1930

By Robert Laurich

Chuquicamata pit was opened in 1915 with steam shovels and steam locomotives brought down from the Panama Canal excavation project. With expansions in the early years, more steam locomo¬tives were brought into the mine. IMPROVED LOCOMOTIVES During the period 1927 to 1937, electric locomo¬tives were purchased and main line and bench tracks were electrified. Third rail was installed up to the working areas. At first, the locomotives were equipped with batteries for service at the shovels, but charge life was too short and they were con¬verted to use the third rail and a reel with 3000 ft of trailing cable for service in the loading area.

Jan 11, 1959

By Charles Will Wright

FRANCE will be given a large portion of the Marshall Plan funds for relief, reconstruction, and industrial development in France and in her colonial possessions. At present that country is not in position to export any large tonnages of the mineral products needed in the United States. However, if, through Marshall Plan aid and private capital investment, production of these products can be largely increased, agreement should be made by which the United States is to get a substantial portion of such increased output in part payment for the material and technical aid they receive. France issued a decree, published in the "Official Gazette" on Feb. 3, 1948, which permits conversion into dollars of dividends derived from dollar investment in Government-approved projects and will agree to a scale of capital amortization to be determined in each individual case. This decree is to encourage private capital to cooperate with local capital in industrial undertakings. The French Colonial Ministry has prepared an extensive program for aid to the mining industries in overseas possessions to be undertaken by

Jan 1, 1948

MARCEL R. DALY (communication to the Secretary?).-The fundamental disagreement between Eugene Coste and the writer proceeds essentially from the contradictory views they hold on the origin of petroleum. This difference cannot be bridged, nor can inorganic and organic theories be discussed here. The writer has suggested that the proper thing in such a case would be to agree to disagree. Coming to the detailed objections further presented by Mr. Coste, the writer feels that, in the main, they take their source in a wrong interpretation of the theory, and the writer is sometimes too generously invested with views that are not his own. 1. The only requirement for the theory is that the oil proceeding from organic remains be distributed in a water-laden sediment, and that this sediment be submitted to the increasing compression due to the continuous accumulation of superimposed strata, which would tend to squeeze out the liquid contents (p. 1152). This squeezing out would be further aided by the distortion of the strata (p. 1148, a). Nothing here makes impossible the slow formation of the oil, if this is considered necessary, as the piling up of the strata in the syncline would require by itself a protracted length of time, and, further, the squeezing-out process is a slow one. Possibly the formation of the oil may even continue during part of the process of distortion. But the mode of formation of the oil and the time and temperature required for it are left to the chemist to decide. The diastrophic theory, which is essentially a theory of motion and accumulation dependent on the laws of mechanics, is not directly concerned with them, provided the general points heretofore outlined be agreed upon. Perhaps it would be wise not to claim too many "eons" for the formation of the hydrocarbons, if the statement made by Sir Boverton Redwood is correct that "the coral reefs of the Red Sea are charged in places with recent petroleum, formed in that torrid climate from the swarming organisms occupying the shallow pools."1

Jan 5, 1917

By S. M. Marshall, A. C. Richardson, H. Y. Yancey

A year ago, Marshall and Bird presented a paper in which a new method of measuring the agglutinating power of coal was described.' The procedure used was to determine the strength of a button containing 10 parts sand and one part coal, formed by carbonizing the mixture in a crucible in an electric furnace. The result of the determination was reported as the total weight in grams required to bring about complete destruction of the button. Correlations were shown between the agglutinating value and some of the characteristics of the different coals that were investigated. This agglutinating test has been in use fairly continuously during the past five years for coals of widely differing coking qualities, and it has shown reasonably concordant results accurate enough for commercial use, although there are many features of the test which should have further scientific study. During the past year a study has been made of some coals of low coking strengths, and incidental to the main investigation some data which appear to be of interest and value were obtained on the loss in agglutinating power caused by exposure to the air. Three coals were investigated, all of which were of the Tertiary age; two were from one field in Asia, and one from a field in the United States. The three were similar, as shown by the proximate and ultimate analyses in Table 1 (moisture-free basis). Coals SA and RA generally contain about 5 per cent. moisture and coal P about 3.5 per cent. moisture on the as-received basis. The large difference in the ash contents of the coals, amounting to practically 10 per cent. between SA and RA, and P, makes difficult a direct comparison of their qualities. In the second section of Table 1 the figures have been put upon an ash-free basis., This table shows that these coals are closely alike. The ultimate analyses are almost identical except for the higher nitrogen content of

Jan 1, 1930

By David Kellogg

THE electrodeposition of iron has been practiced for many years. The earlier work along this line was directed toward the preparation of pure metal, but later applications were the production of thin adherent coatings as used in the electrotyping of Russian banknotes in 1860. A historical discussion of this subject, however, would require too much space and would be inconclusive. Much has been written on the subject but no two experimenters use the same methods or materials. During the war, the British army repair, shops developed a method for building up worn parts of automotive machinery, aero engines, etc., using the cold surfate . bath and low-current density method.1 The method has been used successfully in commercial work for the production of about 6000 repaired parts, therefore experiments along the same lines have since been made at the Westinghouse research laboratory. The apparatus used was essentially that described in the article mentioned except that the current -used for cleaning was obtained from a 3/4-kw. 60-volt, house-lighting generator, direct connected to a 2-h.p., 870-r.p.m., 440-volt, three-phase, type CS induction motor; while the plating current was taken from the storage batteries at any desired voltage. The anodes were made from 0.036 in. (0.9 mm.) Armco iron made into cylinders 5 in. (127 mm.) long by 8 in. (203 mm.) in diameter with a disk of 1/8 -in. (3.17 mm.) micarta, having a 2 in. hole in the center fitted at each end of the cylinder for stirring. The anodes were hung on a wooden rocker frame driven by a wooden connecting I rod directly connected to a small reducing gear, such as is sold by most of the apparatus supply firms; 3 gal. stoneware crocks were used as containers. The solution used by Thomas, 75 gm. of the crystallized ferrous ammonium sulfate per liter, was tried, using the current density recommended by him; namely, 0.33 amp. per sq. dm. Under these conditions the deposit on a ½ -in.

Jan 2, 1922

By V. (“Viv”) R. Forbes

[ ] INTRODUCTION "The Liberal Party believes that the State's mineral resources belong to the people of Queensland and therefore it is essential that the state, on their behalf, obtains maximum benefit from the development of those resources." (Liberal Party, 1980 "Mineral Resources Policy" p.2). "Unless sound policies are implemented.... increased production of minerals will benefit only the already wealthy and the lucky few... A resources tax is essential to ensure that above normal profits are shared by the whole community.... Labor policies on taxation must ensure an adequate return from mining developments to the Australian people." (Labor Party Policy Paper, May 1982 "National Issues relating to rapid expansion of mineral production during the eighties". p.1, 37, 47). Judging from these statements, key political parties in Australia believe that mining profits are lightly taxed and that shareholders get most of the benefits. THE REALITY The Government Share of Income statement in Table 1 attempts to measure the government share of the income generated by the "Big Five" Australian mining companies - Broken Hill Pty Ltd. (BHP), CRA Limited, Utah International, MIM Holdings Ltd., and Western Mining Corporation ("WMC"). These companies control over 70% of Australia's mining industry including all the most profitable mining operations. They dominate the mining and processing of iron and steel, aluminum, manganese, coal, oil and gas, copper, lead, zinc, silver, nickel, gold, ferro-alloys and salt in Australia. They are also major world exporters of most of these products. They are thus a representative sample of the profit-earning side of the Australian mining industry. In their two most recent financial years these five companies had income before tax of A$6,980 million. The Government share of this income was A$6,285 million or 90%. The total market capitalisation of the Big Five is about A$8,480 million. (December, 1982). Governments thus consumed the equivalent of 82% of their total value in just two years. This was taking place while the politicians drafted the above statements calling for an "adequate" share for the people.

Jan 1, 1985

By O. J. Malacarne, D. G. Millenbruch

The use of a series of thickeners for washing of the slime fraction of a leached ore is not uncommon in the uranium industry; however, few ore processing mills have used a thickener circuit for washing leached total ore. The common practice is to wash the sand fraction in classifiers and the slime fraction only in thickeners. At the Uravan mill of Union Carbide Nuclear Co., a total ore acid leach is employed to extract uranium values from sandstone ores. These leached ores are then washed at a nominal rate of from 1000 to 1300 tpd in a series of washing thickeners. A typical screen analysis of the ore being washed in these thickeners is: 25 pct, -200 mesh; 3 pct, +35 mesh; and about 1 pct, +14 mesh. The amount of slimes (-200 mesh) will vary from 20 to 30 pct as the mill receives ore from 150 different mines. The washing liquor is acidic, from a pH of about 2 in the first thickener to 0.6 pH in the last thickener and, of course, all acid duty equipment must be used. The Uravan mill of Union Carbide Nuclear Co. is located in Montrose County, Colo. and is physically located on a canyon wall along the San Miguel River. The thickeners referred to in this paper are located on top of the mesa above the canyon. For purposes of identification, these thickeners are numbered 1 through 8 from south to north. GENERAL DESCRIPTION OF CIRCUIT The circuit utilized consists of eight wooden fir tanks, 60-ft diam by 12-ft deep, set in a line and staggered in elevation by approximately 3 ft. The washing water flows through the thickeners by gravity, while the ore pulp is pumped uphill from thickener to thickener. Adequate piping and pumping capacity are available so that any of the thickeners can be bypassed in the circuit. All the controls for the

Jan 1, 1962

By Horace Knerr

The term. "high-yield-strength," used in the title of Dr. Gillett's paper (p. 40) is obviously relative. His discussion is limited to improved steels intended to compete with the low-cost, low-carbon, hot-rolled, sheet and plate steels of commerce made and used on a tonnage basis, without heat-treatment. In his list of about three dozen steels, only three have a yield strength of 70,000 lb. per sq. in., or over. Double such values are not uncommon in aircraft steels. Dr. Jeffries (p. 21) refers to "light-weight metals," obviously meaning strong alloys of low specific gravity; namely, aluminum alloys of the duralumin type and certain magnesium alloys. In a structural material, "lightness" is determined by two factors, strength and specific gravity. They must always be considered jointly. The basis of comparison is a strength-weight ratio, obtained by dividing the desired strength value, such as tensile strength, yield strength, or endurance limit, by weight per unit of volume, such as specific gravity or pounds per cubic inch1. For example, aluminum is a heavy metal, structurally, unless alloyed and heat-treated to give it high strength. When the strength of a structural metal is raised by heat-treatment or by cold-work, its specific gravity is not appreciably changed, but it is made lighter in direct proportion to the increase in strength because less of it will be required to carry the load. The lightness of the finished structure of adequate strength is the real point of interest. This structure must not only carry designed load, but "stand the gaff" of service, which includes the effects of accidental overload, fatigue, corrosion, loosening of joints, and so forth. Neither Dr. Gillett nor Dr. Jeffries mentions the true "lightest material of construction," which is alloy steel, tubular in form (Fig. 1), assembled by welding and heat-treated to a yield strength in excess of 150,000 lb. per sq. inch.

Jan 1, 1936

L. S. Austin, Denver, Colo. (communication to the Secretary) : Mr Hartman says (p. 4 of the pamphlet) that the penetration of air into the crucible of the blast-furnace " is, of course, a function of the diameter of the nozzle." To this I would emphatically take exception. Fig. 1 represents a vertical ideal section of tuyere, cruciblewalls and charge, immediately at the tuyere, in which the currents of air are represented, both in quantity and in direction, by the tortuous black-lines emanating from the nozzle-opening and passing through channels of the least resistance. As an electric current, flowing by various conductors to a common point, is carried in quantity inversely as the resistance of those conductors, so here the air ramifies through the most open cavities or channels, relatively little of it passing where the resistance due to fine materials is great. This figure represents the course of currents in the vertical plane only. As a matter of fact, they pass away in every plane, as opportunity offers. The effect of blocking or decreasing the area of the nozzleopening would certainly only decrease the quantity of air entering by that particular tuyere, without assisting penetration. The large channels (b, b, Fig. 1, for example) would still carry the larger part of the air, while again the smaller channels (a, a, a) would continue small and take no larger percentage of the air than before. These channels momentarily change, however, with the slow descent of the coke. Further on (p. 5), Mr. Hartman describes the dispersive effect of a single lump of fuel. He has only to conceive the entire spaces before the tuyere-nozzles as filled with such lumps, in order to parallel the condition of affairs I have just explained. It is where the large pieces of the charge come down, that the mass is the most open, and the blast passes most freely. On the other hand, wherever the fine ore collects combustion proceeds slowly, because of the smaller supply of air. The

Jan 1, 1899

By F. Keller

SOME PHRASEMAKER has aptly said that nature made aluminum light but research made it strong. Research has been a vital element in the past progress of the aluminum industry and its future growth likewise depends upon the application of the results of research. The role of aluminum products in World War II is well known and this metal will certainly be increasingly important in the postwar world. Some of the principal developments in the war years were in the field of high-strength aluminum alloys. New and stronger alloys were developed which enabled designers to get increased speed and performance in our fighter planes and bombers. The aircraft industry will continue to use these new materials for peacetime passenger and cargo airplanes. High-strength alloys will also find structural applications in trucks, buses, trains, ships, and bridges.

Jan 1, 1946

By AIME AIME

IT IS impossible in this short sketch to give a detailed description of each part of the plant at Bethlehem, therefore, only such facts will be touched on as are necessary to give a general idea of the works. The extent of the plant, and the fact that the units making up the various departments are located in different parts of the works, make it impracticable to mention the departments in any regular order with regard to their location. They are, therefore, mentioned approximately in the order of their relation to each other with reference to their functions in the making of the various products.

Jan 1, 1924

By H. O. Hofman

INSTITUTE OF TECHNOLOGY, In deternlining experimentally the fusibility of clays, two kinds of methods may be distinguished—the direct and the indirect. Of the direct methods, that of Seger has found

Jan 1, 1899

By Thomas P. Forbath

THE sudden realization that known sulphur reserves amenable to mining by the Frasch hot water process are nearing exhaustion focused attention on widely scattered surface deposits throughout the world. These deposits are not necessarily of lower sulphur content than ores located underneath Louisiana or Texas salt domes which usually average about 30 pct sulphur disseminated in limestone matrix. Their near surface occurrence, however, renders exploitation by the Frasch process impossible. As is well known, the Frasch process depends on the presence of 500 to 1000 ft of overburden and cap rock above the sulphur deposits to permit melting underground sulphur in place by diffusing hot water under pressures of 200 to 600 psig in the formation and raising the molten sulphur to surface by air lift. This process renders possible the production of pure sulphur which is 99.5 pct pure without any subsequent treatment. Surface deposits contain sulphur in the same range of concentrations as the salt dome deposits, i.e., from 10 to 50 pct sulphur, associated with various gangue materials such as silica, limestone, and gypsum. The pirincipal distinction, then, does not lie in the percentage of sulphur contained in the ore, but in the geological nature of the deposit. A recent study' of the world sulphur supply situation estimated 1950 sulphur production in the free world countries at 5.6 million long tons, of which the United States produced 5.2 million tons, or 93 pct of the total. While America's domestic needs alone would have been covered by national production, about 1.4 million tons were exported during the same year. Despite all the steps which are being taken to restrict use of elemental sulphur and to force the fullest possible development of alternate sulphur sources here and abroad, the deficit in elemental sulphur production will probably increase with time. As a result of intensive prospecting for oil throughout the Gulf Coast area discovery of significant new salt domes is held unlikely. With the growing scarcity of sulphur and what appears to be an inevitable rise in price, recovery from deposits not amenable to Frasch-process mining assumes greater economic importance. Untapped Reserves The most important deposits in this category are located in Sicily, where elemental sulphur occurs in Miocene limestone and gypsum formation. Sulphur content of these ores ranges from 12 to 50 pct with an estimated average of 26 pct. Although quantitative estimate of these reserves is not available it is held that they exceed 50 million tons of sulphur. Similar deposits occur also on the mainland which contribute about one-third of Italy's total current annual production of 230,000 tons, but these are known to be nearing exhaustion. Significant surface deposits of volcanic origin are located in South America, Japan and western United States, silica being characteristic gangue con-stituent. The largest of these deposits are in South America. More than 100 extend over a zone 3000 miles long, paralleling the west coast of South America. 'Total sulphur content of these deposits has been estimated to be as high as 100 million tons. The main islands of Japan also possess at least 40 known volcanic sulphur deposits with probable reserves of 25 to 50 million tons.' Prospected reserves in western United States might amount to 2 million long tons, principal deposits being located in the northwestern part of Wyoming, southern Utah, and eastern California. Volcanic deposits of lesser importance are found around the Mediterranean, in Turkey and Greece, and in Africa, Egypt, Abyssinia, and Somaliland. Beneficiation Methods Different methods of beneficiation have been used in these various locations. In Italy the Calcarone kiln and Gill regenerative furnaces are used exclusively. Both utilize heat liberated by burning part of the sulphur in the ore to liquify or vaporize the remaining sulphur, which is recovered by solidification or condensation. The Calcarone kiln is of conical shape, generally 35 ft in diam at base and 18 ft high. A kiln of 25,000 cu ft capacity burns for about two months and yields about 200 tons of sulphur. The Gill furnace consists of a series of chambers with domed roofs. Sulphur is burned and melted in one chamber at a time and the hot combustion gases are used to preheat the ore charge in the subsequent cell. These furnaces operate on a cycle of 4 to 8 days. The recovery yield of both systems is about 65 pct. Sulphur losses amount to 25 pct through the combustion to sulphur dioxide; about 10 pct is retained in discarded calcines. Ores containing less than 20 pct are not considered suitable as furnace feed. These methods are not only wasteful because of the low recovery obtained, but represent a serious atmospheric pollution problem. Sulphur produced ranges from 96 to 99 pct purity and thus does not match Texas or Louisiana sulphur. Owing to the present shortage, sulphur in the Middle East sells

Jan 1, 1954