Search Documents

By T. J. Smolik, Harman, D. W. Fuerstenau

By means of electrokinetic measurements, the surface properties of the aluminosilicate polymorphs (sillimanite, andalusite, and kyanite) and also mullite have been found to depend on the ratio of A10 bonds to SiO bonds in the surface. The Al-toSi ratio in the surface is dependent upon the crystal lographic properties of the mineral, which in turn determine coordination numbers of A1 and of Si, cleavage characteristics, and density of the various solids. Mullite with a greater bulk Al-toSi ratio has the highest zpc of the aluminosilicates. By treatment in dilute acids or by cycling between acidic and basic solutions, alumina is selectively dissolved from the surface of these orthosilicates. This shifts the apparent zpc to lower pH values as the fraction of SiO groups in the surface increases. Thus, surface properties can be altered by procedures that alter the A l-to-Si ratio in the surface. Flotation of these aluminosilicates results from electrostatic interaction of the collector ions with the mineral surfaces. As a result, flotation response shifts in accord with any shift in apparent zpc by pretreatment. Separation of minerals by flotation is based on differences in the physicochemical properties of their surfaces.'-3 For many minerals, adsorption of flotation collectors results from their functioning as counter ions in the electrical double layer at solid-water interface. In such systems, separation depends on differences in the zero point of charge (zpc) of the various minerals. The zpc is defined as the concentration of potential determining ions in solution at which the surface is uncharged. The potential determining ions for inorganic oxide-water interfaces are hydrogen and hydroxyl.4,5 This work is concerned with the effects of crystal structure, composition, and surface preparation on the surface properties and flotation behavior of aluminosilicates. Differences resulting from crystal structure were studied by measuring electrokinetic potentials and determining the flotation behavior of three different aluminosilicate materials having the same chemical composition (Al2O3 SiO2), namely andalusite, kyanite, and sillimanite. Furthermore, the effect of the Al2O3-to-SiO2 ratio on flotation behavior and surface properties was investigated by including synthetic mullite, 3A12O3 .2SiO2. Gaudin and co-workers 6,7 have clearly shown how crystal structure determines the native floatability of certain minerals. Those solids in which the surface is comprised mainly of broken residual bonds possess naturally hydrophobic surfaces. It was found by Bakakin8 that for a number of oxidized lead minerals, differences in floatability were due to the distance of Pb atom from the surface. Only limited work has been done on relating electrical properties of surfaces to crystal structure and composition. Healy et. a1.9 found that the zero points of charge of various manganese dioxides ranged from about pH 1.5 to pH 7.5, and these differences in the zpc's were interpreted in terms of the atomic packing in the various crystals. The research presented here clearly shows that crystal structure and chemical composition do affect the surface properties of aluminosilicates and, in addition, that these effects can be altered by changing conditions under which the surfaces are prepared. CRYSTAL STRUCTURE OF THE ALUMINOSILICATES Sillimanite, andalusite, and kyanite are composed of regionally metamorphosed rocks differing mainly in degree of metamorphism. All three minerals have the same chemical composition, Al2O3 - SiO2, of which sillimanite is the high temperature polymorph and kyanite and andalusite the lower temperature polymorphs. Andalusite and sillimanite crystallize in the orthorhombic system while kyanite crystallizes in the triclinic system. The structure of these three minerals is essentially chains of aluminum-oxygen octahedra linked laterally by silicon and aluminum. The arrangement of these chains in the three minerals is shown in Fig. 1.l4

Jan 1, 1967

By S. R. Mitchell, M. Weissman, J. H. Brown

It has been demonstrated that for fine grinding operations, the energy input (E) and the product size modulus (k) are related by an equation of the form E = Ak1-n (1) where "A " and "n" are constants.(1) Also, it was suggested that "A" is determined by the comminuting device and that "n" depends primarily on the rock. It was the purpose of this investigation to study these constants by determining the form of an energy-size reduction relationship over an extreme range of energy inputs, and at the same time, to evaluate the minimum particle size produced during grinding. The comminution system consisted of a stainless steel laboratory ball mill in which quartz was ground at 60% solids for times ranging from 1 minute to 700 hours. The mill which measured 10" diameter by 12" long was loaded with about 60 pounds of balls ranging in diameter from 3/8" to 1-1/8" and was driven at 55 r.p.m. Quartz was selected for the tests because it is a brittle material for which size distribution data were expected to show a constant distribution coefficient regardless of product size.(1) This permitted specification of product size by a size modulus alone. The quantities measured were the time of grind (measure of energy input) and the specific surfaces of the products. Since no accurate method is available yet for determining particle size directly in the very fine size ranges specific surface data were used for this purpose. The relationship between these two quantities may be expressed as where Cis a constant which includes a shape factor, p is the specific gravity of the solid,_S is the specific surface and D is an equivalent particle diameter. For a material in which the distribution coefficient does not change with size the term (l/S) may be substituted for k in equation L if the proportionality constant "A" is changed correspondingly. This substitution was made in this work but in addition, screen analyses were made on several products to verify the equivalence of the two methods of size specification. EXPERIMENTAL DETAIL QUARTZ Quartz from two sources was tested. One series of tests was made on a clear, high purity crystalline quartz from Brazil and Arkansas, and another series was run on massive quartz fromNewHampshire. Grinding charges of the high purity material consisted of 2000 gram samples of -3-8 mesh particles, while the charges of the New Hampshire quartz were 500 gram samples of a -35+48 mesh screen fraction. The difference in the sizes of these two series of charges was not significant in view of the extreme size reduction accomplished, and the New Hampshire samples were smaller to permit ginding to finer sizes in shorter times than required for 2000 gram lots. SAMPLING AND ANALYSIS Separate charges were ground for all tests in which the grinding times were less than one hour and for all tests on New Hampshire quartz since these products were difficult to sample accurately without affecting the entire charge. During the long time grinding tests the mill was

Jan 1, 1961

By John W. Weeton, Max Quatinetz, Robert J. Schafer

Nickel powders of 1-, 0.4-, and 0.2- average particle size were combined with 0.05- p MgO powder. Oxide was added in quantities of 4, 12, and 20 vol pct. The mixtures were vacuum hot pressed and extruded at 2100°F. In spite of a general tendency to growth of oxide particles during processing, dispersions of fineness comparable to those of Sintered Aluminum Powder, SAP, were achieved. A small amount of oxide considerably improved 1800°F stress-rupture strength, but further oxide addition resulted in a decrease of strength. RECENTLY there has been much speculation concerning the requisites for strong and stable dispersion-strengthened alloys. The nature of the dispersed phase, the stability of the alloys, and variables influencing the mechanical properties of alloys have been given consideration. Such topics have been reviewed by Bunshah and Goetzel. Of the many parameters related to the mechanical properties of dispersion alloys, mean free path between dispersed particles (a measure of the fineness of the dispersion), particle size, and vol pct of the dispersed phase have been shown to be very important. Generally, strength increases with decreasing mean free path, and there is an optimum vol pct of dispersed phase. Just how fine a dispersion ought to be is somewhat open to debate, but Irmann, Lenel, Backensto, and Rose, Gregory and Grant,4 and others have shown in the original SAP-type alloys, aluminum plus aluminum oxide alloys, that better strength is generally obtained with finer dispersions and the best strengths were obtained when the mean free path was less than . Further, Cremens, and rant' showed that in nickel plus aluminum oxide alloys, stress-rupture strength at 1500°F was definitely increasing with decreasing mean free path. In their investigation, however, the finest dispersions that were produced were about 2.0 mean free path. To determine the potential of the nickel plus oxide type of product, it would be neces- sary to obtain dispersions analogous to those of SAP alloys; namely, ones where the mean free path between oxides is less than . Unfortunately, however, it is very difficult to produce extremely fine dispersions of oxides in metals other than those which naturally form refractory oxide skins. There are several approaches to this problem including such procedures as mechanical mixing, internal oxidation, reduction of mixed oxides, and metal deposition from solution. Work at the Lewis Research Center has shown that metal powders 0.1p or finer could be produced by ball milling, when selected grinding aids were utilized.' Because these unusually fine powders were available, it was an initial objective of this study to determine if by mixing of these fine Ni powders with various amounts of MgO (0.05) a fine dispersion of MgO in Ni comparable to those in Al-Al203 might be achieved. A second objective was then to attempt to relate the parameters of structure to 1800°F stress-rupture strength of the alloys. Nickel powders of 1-, 0.4-, and 0.2-p average particle size were combined with 0.05- average particle size MgO powder. This oxide was added in quantities of 4, 12, and 20 vol pct. The mixtures were hot pressed and extruded at 2100°F.

Jan 1, 1962

By A. M. Gaudin, D. W. Fuerstenau

IN concentration of certain ores by soap flotation, prevention of quartz flotation is desired; the contrary is true in treatment of some oxide iron ores. Experimental study of the flotation of quartz goes back at least a quarter of a century.' Clean quartz does not float with fatty acids or soaps but does float when activated by one of many metallic salts. Control of pH is important. Broadly speaking the problem of quartz flotation has been approached from the empirical side, as was the related topic of flocculation or dispersion of quartz suspensions? Empirical studies indicated the existence of critical relationships between the additions of collector and activator. These additions were not stoichiometric for the formation of soaps of the activator cation. For example, Gaudin and Rizo-Patrona found optimum quartz flotation at pH 10.6 using barium activation and oleate collection when the molar ratio of oleate to barium was 1 to 1 instead of 2 to 1, as would be called for formation of Ba(OL),. Cooke and Digre" ' found that if calcium is the activator, a minimum quantity of that agent is required for effective flotation when the pH is 11.5. In other words, if the concentration of Na' exceeds 10 -2.5 mols per liter or if the concentration of H exceeds 10-11 mols per liter, the concentration of Ca++ in solution required for quartz activation is increased. This suggests that H+ is much more effective than Na+ on 10-2.5 quartz, perhaps in the ratio ofp or 108. Schuh- mann and Prakash6 studied anew the activation of quartz by barium, calcium, aluminum, and ferric iron. Salts of these metals are activators provided they are in stoichiometric excess over the collector used with them. Alkaline-earth salts are effective only in alkaline circuits. Important as they are in giving data on the effect of various agents on quartz, all these studies fail to give information on the detailed structure of the quartz-solution interface. A beginning in this direction was made by Gaudin and Chang,? who measured the adsorption of radioactively marked barium and laurate ions at quartz surfaces, and by Gaudin. Spedden, and Laxen,8 ho measured the adsorption of radioactively marked sodium at quartz surfaces. Work has also been done by Bell0 n measurement of the adsorption of sodium ion and chloride ion at quartz-solution interfaces. In all these experimental measurements of adsorption, the solid was centrifuged or filtered from the bulk of the liquor with which it had been associated; and the composition of the solid surface was ascertained by analysis, after allowance was made for the ionic composition of the liquor included with the centrifuged solids on the assumption that it is identical to the bulk liquid. Adsorption measurements give only the total amount of collector adsorbed at the quartz-solution interface; they give no indication of the distribution of these adsorbed ions at the interfacial layer. It is the ionic structure of the solid-solution interface and its importance to flotation that is the subject of this paper. The structure of this interfacial layer can be investigated by means of electrokinetic methods so that by combining electrokinetic studies with adsorption measurements, a more complete picture of the quartz surface may be obtained. The following studies were made to ascertain how electrolytes used in the soap flotation

Jan 1, 1956

By D. J. Schmatz

DISCUSSION OF RESULTS The qualitative correlation between low-temperature ductility and prior high-temperature creep strain in nickel obtained in this investigation confirms the result obtained on high-purity brass by Chen and Machlin. However, the quantitative effect is much smaller in nickel. Comparison can be made on the basis of a prior high-temperature strain that is a certain percentage of the total high-temperature elongation to rupture. In the research of Chen and machlin, the prior high-temperature strain of 1/2 pct equaled 8.5 pct of the total high-temperature elongation at rupture. For nickel, in our experiments, 8.5 pct of 21.2 pct equals 1.8 pct. For eh = 1.8 pct, the loss in ductility in percent equals x 100 = b.5 pct. That is, for equivalent bo Formation of Beta Manganese-Type Structure in Iron-Aluminum-Manganese Alloys D. J. Schmatz IRON-aluminum alloys have gained much interest in the past few years for use as a base material for elevated-temperature alloys because of their excel- high-temperature strain the loss in low-temperature ductility is 8.5 pct for nickel as compared to 60 pct for pure a, brass. It is also interesting to note the observation that in nickel the low-temperature fractures, even at the most extreme high-temperature pre-strain, were partly trans crystalline and partly intercrystalline. In the case of a brass, these fractures were completely intercrystalline. According to the data on the percent of the grain boundary area that is cracked, at 22 pct high-temperature elongation, about 12.5 pct of the grain boundary area does not carry load. Thus, the inter-crack areas are carrying a stress that is about 11 pct higher than the nominal stress. A simple model predicts that the overall elongation, which is primarily the elongation in the bulk of the specimen, will correspond to the nominal stress when the stress in the intercrack area equals the tensile strength. Quantitatively this model predicts the equation The form of this equation will agree with that found if the strain-hardening exponent, n, equals unity. Actually this model is too gross an approximation to yield good quantitative results. The question naturally arises as to whether in ordinary hot-working, such as hot-rolling, intercrys-talline cracks are introduced that affect the low-temperature properties. It appears that the answer is that such a possibility cannot be overlooked, if the hot-working induces tensile stresses at temperatures above the equicohesive temperature and if the material tends to be notch sensitive at low temperature. ACKNOWLEDGMENT This research was supported by the Aeronautical Research Laboratory, Directorate of Research, Wright Air Development Center, United States Air Force. REFERENCES lC. Zener: Fracturing of Metals, 1948, Cleveland, ASM. 'H. C. Chang and N. J. Grant: Mechanism of Intercrystalline Fracture. AIME Trans., 1956, voL 8, p. 544; lownal of Metals, May, 1956. 'E. S. Machlin. CreepRupt ure by Vacancy Condensation, AIME Trans., 1956, vol. 8, p. 106; lownd of Metals, February, 1956 'C. Chen and E. S. Machlin: On a Mechanism of High-Temper at ure Inter-crystalline Cracking, lownd of Metals, July. 1957. p. 829. Alloys lent oxidation resistance. Binary alloys of aluminum in iron are ferritic and consequently have poor hot strength. Alloys of iron-aluminum-manganese were made in an attempt to produce an austenitic alloy containing sufficient aluminum to retain the oxidation resistance of binary alloys of iron-alumi-

Jan 1, 1960

By T. M. Morris, W. E. Horst

W. E. Horst—In regard to the flotation rate being described as "first orcler" for flotation of quartz particles below 65 p in size (or any size studied in this work) in this paper, it appears that the authors' conception of rate equations is not in agreement with cited references. A first order rate equation has as one of its forms the following: a In.=a/a-x=kt where a = initial concentration, a—x = concentration at time t, t = time, and k = constant. The constant, k, has the dimension of reciprocal time which is similar to the specific flotation rate, Q. described by Eq. 2 in the authors' article, as has been previously discussed by Schumann (Ref. 1 of original article). The plotted data presented in Fig. 4 of the article utilizes the specific flotation rate, Q (min.'); however, there is not adequate data given to indicate the order of the rate equation which describes the flotation behavior of the quartz system studied. Results from the experimental work indicate that the relationship between rate of flotation (grams per minute) and cell concentration (provided the percent solids in the flotation cell is less than 5.2 pct and the particle size is less than 65 p) is described by an equation of the first order (R, = k c+", n being equal to 1 in this size range) and the use of the first order rate equation does not apply. Similarly the relationship for other particle size ranges studied is expressed by equations of the second or third order depending on the magnitude of n. T. M. Morris—The authors are to be commended for the experiments which they performed. As they state in their discussion the concentration of collector ion In solution did change with change in concentration of solids in the flotation cell. Since for a given slze of particle, flotation rate increases with concentration of collector until a maximum is reached, the effect of concentration of particles in their experiments was to vary the concentration of collector ions. A collector concentration which insures maximum supporting angle for all particles eliminates the unequal effect of collector concentration on various sized particles and the effect of size of particles and concentration of particles upon flotation rate could be more clearly assessed. I believe that if the authors had increased the concentration of collector to an amount sufficient to attain a maximum supporting angle for all particles they would find that the specific flotation rate of particles coarser than 65 p would be constant with change in the concentration of solids in the flotation cell, and that a first order rate would apply to the + 65 as well as to the —65 p sizes. It might also be discovered when this change in collector concentration was made that the maximum specific rate constant would be shifted toward a coarser fraction than when starvation quantities of collector are used since this practice favors the fine particles and penalizes the coarse particles. P. L. de Bruyn and H. J. Modi (authors' reply)—The authors wish to thank Professor Morris for his kind remarks and for mentioning the influence of equilibrium collector concentration on flotation rate. With a collector concentration sufficient to insure maximum supporting angle for all particles, a first order rate equation may indeed be found to be generally applicable irrespective of size. Such a concentration would, however, lead to 100 pct recovery of the fine particles and consequently defeat the essential objective of the investigation to derive the maximum information on flotation kinetics. To establish absolutely the validity of any single rate equation for a given size range, the ideal method would be to work with a feed consisting solely of particles of that size range. Use of such a closely sized feed would also eliminate the possibility of the interfering effect of different sizes upon one another. The authors do not believe that increasing the collector concentration would shift the maximum specific flotation rate (Q) towards a coarser fraction. Experimentation showed Q to be independent of solids concentration for all particles up to 65 µ in size, whereas the maximum value of Q was obtained in the range 37 to 10 p. Professor Morris contends that the addition of starvation quantities of collector favors fine particles at the expense of coarse particles, but the reason for this is not entirely clear to the authors. The comments by Mr. W. E. Horst are concerned only with the concept of the term "first order rate equation." According to the usage of this term in chemical kinetics, time is an important variable, as is shown in the equation quoted by Mr. Horst. All the experimental results reported by the authors were obtained under steady state continuous operations when the rate of flotation is independent of time. To be consistent with the common usage of the "first order rate equation," it would be more satisfactory to state that under certain conditions the experimental results show that the relation between flotation rate and pulp density is an equation of the first order.

Jan 1, 1957

By J. Weertman

It is shown that conditions suitable for the conversion of straight dislocations into helices are common in crystals hardened either through long-range dislocation interaction or by jog formation on dislocation lines. For dislocations other than screw dislocations or dislocations nearly screw in orientation, helices can be formed with the aid of core difhsion at temperatures low relative to the melting point of the material. It is assumed that, once formed, helices will degenerate into dislocation tangles. THE dislocation tangle is one major dislocation arrangement observed by the transmission electron microscope which had not been predicted previously from dislocation theory. Since first being observed, the tangle itself has become important in applied dislocation theory. The Cambridge school (P. Hirsch) bases part of its theory of work hardening upon this phenomenon.' In spite of the fact that the tangle obviously is a structure of prime importance to a cold-worked crystal, until recently relatively little attention has been paid to the question of exactly why or how tangles arise. It was generally assumed at first that cross slip and perhaps jog formation will lead to tangles. However Wilsdorf and schmitz2 concluded that cross slip cannot markedly contribute to the tangles. The Wilsdorfs and Maddin3'* have proposed that tangles arise by means of prismatic dislocation loops and superjogs which are produced by a precipitation of point defects. Dislocations with superjogs or which have joined with prismatic loops are themselves dislocation sources and they can produce new dislocations, a process they call "mushrooming", which then tangle with each other. There is no question that the Wilsdorfs et al. mechanism as well as the cross slip one can pro- duce tangles. However these may not be the only paths leading to tangle formation. In this paper we wish to consider another way tangles can form. Our work will be based on the theory of dislocation screw We wish to show that whenever a crystal is cold-worked there always is present a "driving force" leading to helix formation and thus to tangle formation. We do not expect to observe well-developed, regular helices in cold-worked metals. Rather we would expect that after a helix is formed random interactions with nearby dislocations will cause a well-developed helical dislocation to go over into an irregular form. A dislocation tangle is, of course, a grouping of dislocations with irregular forms. Therefore we feel that, in accounting for the formation of dislocation tangles, it is sufficient to show that many dislocations in a cold-worked crystal will take on helical form. The crucial step is helix formation. In order to have a straight dislocation assume a helical form, diffusion of vacancies, or interstitials, must occur. Our discussion of tangle formation therefore will be limited to crystals which have been deformed at temperatures ranging from about one fifth to half their absolute melting point. In this tem per a ture range appreciable core diffusion is possible. (There is no problem in explaining tangle formation at temperatures greater than half the melting point. At such temperatures dislocation climb through a bulk diffusion of point defects gives an extra degree of freedom to dislocation motion. This extra freedom of motion makes tangle formation easy.) At temperatures much below one fifth the absolute melting temperature diffusion processes are sufficiently slow that helix formation does not occur. Of course helix or tangle formation could occur in material deformed at very low tempera-tures which was subsequently warmed in order to make the thin specimen necessary for electron-microscope examination. Since within the temperature range of approximately one fifth to half the melting temperature the diffusion of point defects in the core of the dislocation is rapid, we can reasonably assume that within

Jan 1, 1963

Executive ARTHUR S DWIGHT, Chairman B THAYER CHARLES F RAND P MATHEWSON J V W REYNDERS Membership WILLIAM H BASSETT, Chairman W Y WESTERVELT Vice-chairman P MATHEWSON H G MOULTON F T RUBIDGE Finance WALTER H ALDRIDGE, Chairman GEORGE D BARRON GALEN H CLEVENGER

Jan 1, 1923

By AIME

WE produce Charles Van Ormer "Charlie" Millikan as living proof that man need not make a loud noise to be heard. His quietly affable, analytical, and soft-spoken manner in the face of all problems belies his ability to "get tough" when the situation demands it. As a chief engineer with many responsibilities for the success of a large producing company there must have been many occasions to tempt Charlie to excitement, but there are few, if any, who can say they saw him yield. He has an abiding faith in the benefits of hard and persistent work and will not admit the existence of a problem that cannot be reduced by it.

Jan 1, 1948

By R. J. Caro

The Anaconda phosphate plant was put into operation in the fall of 1923. Its present daily operating capacity is approximately 170 tons of treble superphosphate and 16 tons of phosphoric acid analyzing 42 pct P2 O5 and 52 pct P2 Os, respectively. As a result of the continued increased demand for phosphates, Anaconda decided in 1947 to expand the plant's daily output to 270 tons of treble superphosphate and 54 tons of phosphoric acid. The present daily plant intake is 335 tons of wet (footwall) phosphate rock analyzing 31.7 pct P² O5 and 0.28 pct V² O5. The rock is shipped from Anaconda's mine at Conda, Idaho, in open railroad cars, having been crushed to pass 3/8 in. mesh at the mine.' The expansion program will require an increased intake of 300 tons of rock per day. The hanging-wall rock anaIj-ses approximately 30.5 pct P2 O5 and 0.11 pct V² O5, and will be beneficiated in a new washing plant under construction

Jan 1, 1950

By AIME

D R. GILLSON, who was born in Evanston, Ill., in 1895, is another one of those geologists who received his early inspiration and foundation in his science from that great teacher at Northwestern University, the late Professor U. S. Grant, and then went on to give his time and interest to Institute affairs-like those other Northwestern men, Arthur Blair, Gilbert Cady, Charlie Behre, Evan Just, Ian Campbell, Clayton Ball, and many others. After serving in the Navy in the first World War as, of all things for a geologist, a commissary officer on a transport, he went on to MIT and took his doctor's degree under Waldemar Lindgren in 1923. He even assisted in mineralogy at Harvard and thus had training under another great teacher, Charles Palache. He taught mineralogy and petrography at MIT from 1923 to 1928. After several summers of field work as an assistant in the U. S. Geological Survey, Dr. Gillson joined the staff of the du Pont company.

Jan 1, 1947

By Zay Jeffries

From the title of this chapter the reader could expect an attempt to out- line the anticipated shape of things to come, mineralwise. We have no crystal ball and if we possessed one we could claim no expertness in its use. In the first place no one can tell the future status of man. No one has any way of knowing to what extent peace will prevail, nor to what extent changes may occur in national sovereignties or forms of government or in international relationships. So future man is an uncertainty. Nor can we predict new developments that may result in significant changes in man's status or in the mineral industry or both. If, for example, this chapter had been written in the middle 1930's, nearly everything that has happened since in the fields of atomic energy and space technology would have been missed. Yet what vast changes these I have made in the status of man! Also the changes in the mineral industry have been important. A writer would have been bold indeed had he prophesied that uranium would play such an important role. But we need not confine our foggy vision to these fields. The steep rise in the use of aluminum, titanium, and germanium reflects the unpredictable in what may be thought of as the more normal pursuits. This should not discourage one from using the past and currently observable trends as bases for limited predictions. To do this, however, it is desirable to make certain assumptions about man's status without pretense that these assumptions have a high probability of fulfillment: 1. Only minor changes will occur in the geographical boundaries of the nations of the world. 2. World War III will not take place in the near future. 3. As a consequence of (2), man will not destroy himself by wanton use of atomic weapons. 4. Disarmament will take place, if at all, gradually rather than all at one time. Under the above assumptions the world will enjoy a period of relative peace even though the status may be one of an armed truce. The assump-

Jan 1, 1964

By Michel Dupuy, Daniel Calais

The study of self-diffusion of plutonium in E phase has been carried out by the welded couples method. The tracer used was puZ4O which is detected by its X-ray emission (conversion lines of uranium which are computed between 13 and 21 kev). Intensities were measured with a scintillation counter. Each layer was removed in a direction parallel to the original interface with a grinding machine and a thickness measured with a pneumatic comparator. The concentration-penetration curves obtained were corrected for the effect of heating time from room temperature to annealing temperature and for the expansion due to phase transformations of plutonium. They were analyzed by the generalized Gruzin method. Self-diffusion of plutonium in E Phase is very fast cm per sec between 500" and 620°C) and the diffusion zones are 2 to 3 mm wide for annealing times ranging from 30 min up to 10 hr. The Arrhenius law gives the temperature dependence in the form: From the point of view of self-dqfusion, PUE phase falls into the anomalous bcc metals category (Tip , Hfp, Zrp, Uy) with a low-frequency factor and an activation energy lower than those provided by standard correlations. No theory proposed hitherto to explain these anomalies (influence of dislocations, of extrinsic vacancies bonded to inlpurities, of bi-vacancies) can clearly explain the self-diffusion coeffzcients of plutonium. DIFFUSION in bcc metals is a present-day problem. A recent symposium (Gatlinburg, 1964), followed by a book,' has been devoted to it. A great many experiments seem to show that diffusion in certain bcc metals obeys unexpected laws. The activation energies measured are sometimes strangely low (B hafnium, y uranium). For certain metals (0 zirconium, p titanium) the curves of log D (D = diffusion coefficient) as a function of 1/T (T = absolute temperature) are not linear. The frequency factors Do, which are of the order of 1 sq cm sec-' in fcc metals, vary from 1 to 10~6 sq cm sec-'. Various theories have been put forward to explain these anomalies; none is yet satisfactory. We wished to introduce a new experimental result by studying the self-diffusion in c plutonium. This allotropic phase, stable from 475°C up to the melting point (640°C), is in fact bcc. Unfortunately, nothing is known of the characteristics of the point defects in this phase, which limits the scope of the hypothesis which can be made about the mechanism(s) of self-diffusion in plutonium. 1) EXPERIMENTAL METHODS 1) Principle. We used the welded couple method. The two pellets of the couple initially have different 240 isotope contents (X emitter). After diffusion, the concentration/penetration curves are drawn up by the generalized Gruzin method. 2) Gamma Spectrography. The metal used in our study is plutonium, either low in puZ4O (isotopic content 1 pct) or high in puZ4O (8 pct). The latter also contains plutonium 241 (-1 pct) and 300 ppm of ameri-cium produced by the reaction Pu2U-AmM1 + 8-. The emission spectra of these two plutoniums placed in leak-tight vinyl bags have been studied by y spectrograph~. The detector is a thin crystal of thallium-doped sodium iodide. The activity of the plutonium rich in 240 is about twice that of the plutonium low in 240 in the energy band of 17 kev (L conversion lines of uranium); this band was used in these measurements. 3) Preparation and Examination of the Diffusion Couples. Diffusion couples were made from plutonium with a high and low PU"' content. Pellets (6 6 mm. thickness 3 mm) mounted on a polishing disc with ground parallel faces were polished mechanically on both sides. In this way, pellets with two parallel faces were easily obtained. The polished pellets were joined by a 6 phase anneal (420°C, 1 hr) in a small screw press (pressure of 20 kg per sq mm cold); a centering ring enabled the two pellets to be pressed coaxially. The couples then were subjected to the diffusion treatment by annealing in the E phase in sealed silica ampules in argon at atmospheric pressure. The annealing temperatures and times are given in Table I. The couples were encased in a mild steel ring, the joint interface being thus parallel to the ground face of the ring. The diffusion couple/ring assembly underwent successive abrasions by means of a magnetic plate grinder. The thickness of the abraded layer was measured with a Solex pneumatic comparator when it was less than 0.1 mm (accuracy 0.2 p) or with a mechanical micrometer (accuracy 3 p) for passes of the order of 0.2 mm. All these operations were done in glove boxes, as plutonium is particularly toxic. After each abrasion we determined the emission spectrum of the ground face. The emissive surface is defined by means of a diaphragm 3 mm in diam. We noted more particularly the X activity in the 17-kev

Jan 1, 1969

By Samuel D. Warriner

(Wilkes-Barre Meeting, June, 1911.) THE dealings between concentrated capital invested in the conduct of our various industries and the combinations of labor known as "trade union organizations," have produced not only in the United States, but abroad, many novel methods of negotiation between employers and wage-workers. The size and strength of these organizations have destroyed the personal elements formerly governing the dealings between employer and employee and have produced various forms of trade-agreements now in more or less successful operation. The difficulty, however, has- been to secure consent of both parties to an equitable agreement. For this purpose there have been devised various forms of arbitration, either compulsory under the shadow of governmental legislation, or voluntary by mutual agreement. But these have not been altogether successful from a technical stand-point, for the reason that a compromise has generally been necessary, and in an effort to reach an agreement, terms have been made which have been neither fair nor satisfactory to either of the contending parties. The Anthracite Board of Conciliation represents one of the few thoroughly successful courts for the settlement of trade-disputes, if not the only one which has yet been evolved. The prestige of this board rests upon its successful treatment of the labor-troubles of the anthracite region for a period of more than eight years, and upon the fact that it has been able not only to reach decisions based upon the merits of the controversies, but to enforce its decisions upon both the employees and the employers. It has never been obliged to shape its conduct to secure the consent of the contending parties, and its decisions have been strictly and, in the main, cheerfully observed. The remarkable feature of this board has been that it has

Aug 1, 1911

By B. H. Bergstrom, Will Mitchell, T. G. Kirkland, C. L. Sollenberger

IN a previous article' the authors outlined a study of the variables in rod milling and also reported data from a series of open circuit grinding tests on a massive limestone in a 30-in. x 4-ft end peripheral discharge rod mill. As a second part of the experimental program, an analysis is now presented for the 30-in. x 4-ft overflow rod mill grinding under identical conditions, except that discharge ports on the periphery of the mill shell have been sealed so that the products from the present series overflowed through a 9-in. diam .opening in the center of the end plate. A variance analysis has been made of the combined data for the two experiments, and performances of the two mills are compared here. Included in the first report' were descriptions of feed preparation, rod mill circuit, instrumentation and controls, and techniques used to evaluate data. Dependent and independent variables were defined, and variance analyses were made to test the relative significance of variables and to establish magnitude of error for the experiment. Significant data were plotted in various combinations, and conclusions were drawn from the graphs. The procedure and analysis in this series of tests follows the first tests and is not repeated. Data from the second series are recorded in Table I. Listed in the first three columns are the independent variables of feed rate (1000, 2000, 3000, 4000, and 5000 1b per hr), mill speed (50, 60, 70, 80, and 90 pct of critical), and pulp density (50, 60, 70, and 80 pct). The dependent variables, Pso, P100, reduction ratio, slope of the log-log sieve analysis curve, power demand, and Bond work index follow. Of these, only the reduction ratio and the Bond work index were analyzed for significance. Production of new surface as calculated from sieve analyses has not been included for this series because of the questionable assumptions that have to be made to satisfy the formulas involved. The large number of products obtained during the runs precluded the use of surface measurement techniques by the gas adsorption methods at this time; however, samples of all products have been stored for future reference. To test the consistency of the reporting of the sieved products, an averaged sieve analysis was calculated from the wet-dry plots obtained from the three product samples of each run. The resulting averaged analysis was plotted and the P80, selected. The relative deviations of the P80's from each of the three product samples with respect to the P80 of the averaged analysis were then calculated. In only two sets were the relative deviations (6.2 and 9.9 pct) considered excessive. In each of these two sets, one sieve analysis was obviously out of line; hence that analysis was ignored and new averages were computed. This reduced the relative deviations to 1.2 and 2.7 pct respectively. The relative deviations of the product analyses with respect to their averages ranged from 0.1 to 1.4 pct at 1000 lb per hr, 0.0 to 1.1 pct at 2000 lb per hr, 0.2 to 3.0 pct at 3000 lb per hr, 0.3 to 4.3 pct at 4000 lb per hr, and 0.5 to 5.2 pct at 5000 lb per hr. The relative deviation of the 80 pct passing point for 96 dry sieve analyses of the feed with respect to that of the averaged analysis was 7.6 pct. This slightly higher percentage can probably be attributed to a greater proportion of tramp oversize in a crusher product than is ordinarily found in a rod mill product. The last column on Table I lists the adjusted work index, which has been used as the measure of efficiency for the various combinations of operating conditions investigated. Efficiency increases as the index becomes lower. It was reported in the previous paper that the work indexes for the Waukesha limestone used in these experiments decreased as the product size decreased (as calculated from Bond grindabilities). That is, this limestone becomes easier to grind as the material becomes finer. This is unusual, because the work index for most materials as calculated from the Bond grindability has remained constant as the product size decreased or has increased slightly. Table II lists the results of Bond grindability tests at all mesh sizes from 3 to 200 and the work indexes calculated from them. To remove this variation of work index with product size from the data so that results would apply to any material of constant work index, the work index values shown in Table II were plotted against product size on log-log paper. From this curve (a straight line function in this case), the expected work index for the product size for each of the runs of the experiment was obtained. The work indexes as calculated from the reduction ratio and energy consumption were then divided by the corresponding expected work index. The results obtained are reported in percentages on Table I as adjusted work index and are actually percentages of the work index for the Waukesha limestone at the size in question. Multiplication of the work index value for a material of constant index by these percentages should allow the application of the adjusted work index curves to the material. Only the adjusted work index values, not the actual experimental values, were used for the variance analyses and for the graphs.

Jan 1, 1956

By R. L. Fullman

IN the investigation of metallurgical transformations and the relationships between microstructure and properties of metals, it frequently is desirable to obtain a measurement of the relative amounts of the various phases present and of the mean size of particles into which each phase is dispersed. The relative amounts of the phases can be measured by the classical methods of area, lineal, and point analysis,1-5 in accordance with the principle that the volume fraction of a phase, the fraction of a polished cross section occupied by the phase, the fraction of a random line occupied by the phase, and the fraction of randomly arrayed points occupied by the phase are all equal. The validity of this relationship depends only on the attainment of a truly random sample of area, length, or points, and not on the size, shape, or distribution of the particles constituting the phase. Smith and Guttman8 have derived a relationship between the interface area per unit volume S, and the measurable quantities L., the interface length per unit area on a cross section, and NL, the number of interfaces per unit length intersected by a random line. Their equation, Sv = — L8 = 2NL is also valid regardless of the distribution of particle sizes and shapes. In contrast to the situation concerning measurement of relative fractions of phases and of interface area, the measurement of particle sizes in opaque samples has not been subjected to a complete analysis. It has been common to measure some lineal or area dimension of particles on a polished cross section and to use the mean value as a qualitative measure of particle size. In the present paper, quantitative relationships are established among the various mean dimensions on a polished cross section and the actual dimensions of the particles present. Particles of Uniform Size Spheres: If a metal sample contains particles of a phase a dispersed in the form of spheres of uniform size, a polished cross section through the sample will reveal circular areas of phase a with radii from 0 to ?, the radius of the spheres. Consider a cube of unit dimensions to be cut from the sample. If a cross section parallel to one of the cube faces is examined, the average number of particles per unit area (N,) equals the number of particles per unit volume (Nv) times the probability p1 that the plane would intersect a single sphere positioned at random within the unit cube. Since, of the various possible positions for the cross-sectional plane over the unit length from top to bottom of the cube, only those positions existing over the length 2r would lead to the plane intersecting the sphere, the probability of intersecting a single sphere is just 2r. N8= Nvp1 = Nd-2r [1] Applying the equality of area and volume fractions, the relationship is found between sphere size and average area s of uniform spheres intersected by a random cross section, 4 - f = NV V = Nr . — pra = N s = Nd . 2rs S = —pr2 [2] A similar analysis reveals the average traverse length across spheres of uniform size when random lines are passed through the sample. If a randomly oriented unit cube is cut from the sample and a randomly positioned line is passed through the cube parallel to a cube edge, the number of spheres intersected by the line (Nl) equals the number of spheres per unit volume times the probability p1 of the line hitting a single randomly placed sphere in the cube. Since possible positions of the line occupy unit area, and possible positions for which it will pass through the sphere occupy an area of pr2, the probability of the line hitting a randomly placed single sphere is pr2. NL = Nv p1 = Nvpr2 [3] Combining this relationship with the equality of volume and lineal fraction, the desired relationship is obtained between radius and mean lineal traverse length -i, for spheres of uniform size. 4 - - 3 l=4/3r [4] Circular Plates: Consider a sample containing particles of a phase a in the form of circular plates of uniform radius r and thickness t, where r >> t. If the plates are randomly oriented, as in a sufficiently large sample of a fine grained polycrystalline material, area and lineal analysis may be carried out with parallel cross-sectional planes and lineal traverses. If the plates are not randomly oriented, it is necessary to randomize the orientation of the cross-sectional planes and traverse directions. Let a unit cube be cut from the sample, and a cross-section plane be passed through the cube parallel to one of the cube faces. The number of plates cut by the cross-sectional plane per unit area is equal to the number of plates per unit volume times the probability of a plate intersecting a single randomly positioned and randomly oriented plate in the cube. If J is the component of the plate diameter in the direction normal to the cross-sectional planes, the probability of a plane cutting a single randomly oriented plate is equal to J, the mean value of J for all possible orientations of the plate. Let 4 be the dihedral angle between a plate and the cross-sectional plane, and let p?, d? be the probability that a plate makes an angle between 4 and ? + d? with the cross-sectional plane. Then for ran-

Jan 1, 1954

By Luther Wagoner

Having given in a former paper1 the results of assays of sea-water, bay-mud, dredgings from San Francisco bay, etc., and believing it might be interesting to extend the work to include some deep-sea dredgings, I procured from the Smithsonian Institution six samples taken by the U. S. steamer Albatross, and marked as follows: Depth in No. station. Locality. Latitude. Longitude. Fathoms. 1. 2103. Off Delaware bay. 38' 47' 20" N., 72o 37' W., 1,091. 2. 2265 to Between Chesapeake 35° 37' N., 74O to 75O W., 49 to 70. 2297. bay and Hatteras. 3. 2420. Off Chesapeake bay. 37' 03' 20" N., 74O 31' 40" W., 104. 4. 2528. East of Georges 41° 47' N., 65o 37' 30" W., 677. bank. 5. 2572. SE. of Georges bank. 40° 29' N., 66O 041 W., 1,769. 6. 2681 South of Nantucket. 39' 43' N., 70' 29' W., 990. The above samples were assayed by the cyanide-method, described in my former paper (p. 807), about 30 g. of sample being used, and the following results were obtained: Value in Milligrams Per Metric Ton. No. Station. Gold. Silver. 1. 2103. 145 1,014 2. 2265 to 2297. 44 304 3. 2420. 15 353 4. 2628. 267 1,963 5. 2572. 125 377 6. 2681. 66 414 No. 4, Station 2528, consisting of red clay and volcanic ash, mas re-assayed ; 35 g. was roasted at a low heat for one hour and weighed 34.05 g. after roasting; the color was changed to a deep brick-red; and when assayed by the cyanide-method

Jan 1, 1908

Aamot, Olav Crone, Research Engr., Norsk Elektrokemisk Kongensgt, 18, Oslo, Norway ?29 Abbott, Clarence E., V.P., Charge of Raw Materials, Tenn. Coal, Iron & R. R. Co., 1242 Brown-Marx Bldg., Birmingham, Ala. '04 Abbott, Louis Benjamin, Chief Engr., Consolidation Coal Co., Watson Bldg., Fairmont, W. Va. '15 Abel, Raymond L., Asst. Prof., Dept. of Pet. Refin., Univ. of Pittsburgh Pittsburgh, Pa. '28 Abel, Walter D., Cons. Engr 364 S. Cloverdale Ave., Los Angeles, Calif. '32 Abele, Louis T 1457 Euclid Ave., Zanesville, Ohio. '31 Abell, Leo M Sullivan Concentrator, Chapman Camp, B. C., Canada. '31 Aborn, Robert H., Asst. Met., Research Lab., U. S. Steel Corp., Lincoln Highway, Kearny, N. J. '19 Abraham, W. E. V., East India United Service Club, 16 St. James' Sq., London, S. W. 1, England. '28

Jan 1, 1936

By AIME AIME

THE initial meeting on Mining Methods* opened at 10 o'clock Monday morning with Scott Turner as chairman and W. Spencer Hutchinson as vice- chairman; about 60 attending. After preliminary announcements Theodore Marvin was called on for his paper,, entitled "Rock Tunnel Methods," which has been appearing serially in The Explosives Engineer. Marvin read the introduction and called attention to the account of one or' two particularly' interesting projects, such as the. Brooklyn water supply tunnel. E. D. 'Gardner, Char1e.s S. Hurter, L. D. Lamont and Spencer P. Howell took part in the discussion, Howell commenting on the fact that, in one case cited, misfires had occurred through detonator wires 'coming in contact with the case of an unapproved flashlight, .,: and that all flashlights should be approved.

Jan 1, 1931

By D. A. Rice, M. C. Fuerstenau

Flotation data indicate that sulfonate and amine adsorb physically on manganese oxide; oleate also adsorbs physically if the zero point of charge is sufficiently high. Chemisorption of oleate occurs on pyrolusite between pH 8 and 9, and possible mechan- isms of collector adsorption involving metal ion hydrolysis are discussed. The flotation characteristics of most metal oxides1-15 have been examined with standard collectors such as fatty acids and sulfonates. From these studies it would appear as though electrical phenomena are important when shorte r-chained collectors are involved. For example, Iwasaki, Cooke, and Choi9 have shown that dodecyl amine and dodecyl sulfate float iron oxide above and below the zero point of charge, respectively. In another system, D.W. Fuerstenau and Modi10 have shown that dodecyl sulfate, dodecyl

Jan 1, 1969