Search Documents

By R. S. Rickard, M. C. Fuerstenau

Anodic polarization curves for iron dissolution and cathodic polarization curves for copper deposition and ferric and hydrogen ion reduction were studied. These results were used to predict the relative rates of the reactions: The rates of the first two reactions were found to be first order with respect to the reacting ion, and the rale-controlling step was diffusion of the ions to the callzode surface. The rate of hydrogen ion reduction in an oxygen-free solution is dependent on the reciprocal of the square root of the hydrogen ion activity. In solutions containing oxygen, the rate of hydrogen reduction becomes dependent on the square root of the partial pressure of oxygen. At equal concentrations copper precipitation occurs about twice as fast as ferric ion reduction. In an air-saturated solution containing 0.01 M cupric ion at pH 2, the rate of hydrogen ion reduction zs about 10 times slower than that of copper precipitation. At pH values below 3, the rate of hydrogen reduction in oxygen-free solutions is very slozu. COPPER cementation has been utilized industrially for many years as a means of recovering copper from aqueous solutions. There are many different types of cementation plants, but all simply provide a means of contacting iron with relatively dilute copper solutions. In the past little or no attention has been paid to rates or mechanisms of the reactions involved. As a result, this and other studies'-3 have been undertaken recently to establish the important parameters in this system. The reactions involved in copper cementation by iron are: Since transfer of charge is involved in every case, these reactions should be considered from an electrochemical point of view. In any electrochemical system involving electrolytic conduction, passage of electrons necessitates ion transfer to the respective electrodes according to Faraday's law. The current in the system will be proportional to the rate of ion transfer, and, therefore, when the current in the galvanic cell is known, the rates of the reactions involved can be determined. Galvanostatic electrode measurements5" are applicable for these electrochemical studies, in that with this technique polarization curves (current density vs electrode potential) are established by impressing a constant current through an electrode and measuring the electrode potential. Once the current density, electrode potential, and reacting area are known for each reaction in this cementation system, the rates of the iron-consuming reactions can be determined. EXPERIMENTAL MATERIALS Several metal electrodes were used in this investigation; they are shown in Table I. Solutions were made with reagent-grade salts and conductivity water. Air, nitrogen, and oxygen were employed. All of these gases were saturated with water and degreased prior to use. EXPERIMENTAL PROCEDURE The experimental work was divided into two general areas. The first area involved galvanostatic measurements, which were used to determine the rates of reactions as a function of various parameters. The second area comprised actual cementation experiments to check the rates predicted from the electrode measurements. Galvanostatic Electrode Experiments. Polarization curves were obtained using a standard galvanostatic technique5'= with the apparatus shown in Fig. 1. The various electrode polarization experiments were run the same way except for changes in solution composition, polarity, and type of measured electrode. The general procedure involved the following steps: 1) a solution was made 0.5 M in sulfate ion and to the desired cation concentrations; this solution was placed in a constant-temperature bath and saturated with the desired gas; 2) the electrodes were cleaned and placed in the electrode holder; 3) the previously cleaned apparatus was assembled and immersed in a constant-temperature water bath (temperature controlled to ± 0.05"C); 4) the electrode was then positioned; the solutions were introduced, and the polarization meas-

Jan 1, 1969

Adams, Benjamin C., Jr., Student, Univ. of Oklahoma Norman, Okla. '36 Adams, Ernest C., Student, Univ. of Illinois 908 W. Green St., Urbana, Ill. '35 Adams, George H., Student, Colorado School of Mines Golden, Colo. '36 Adams, Robert Keller Mitchell Hotel, No. 18, Golden, Colo. '35 Afshar, Hadji Khan A., Student Box 63, Univ. Sta., Moscow, Idaho. '36 Ahrenholz, Herman William, Jr., Student, Lehigh Univ Bethlehem, Pa. '35 Alger, Robert P., Student, Missouri School of Mines & Met.Rolla, Mo. '36 Allen, Paul W., Student, Mass. Inst. of Tech Cambridge, Mass. '35 Allen, R. M., Jr., Student, Virginia Polytechnic Inst., "G" Co.Blacksburg, Va. '35 Alley, John Arnold, Student, Montana School of Mines Butte, Mont. '36 Amberger, R. H., Student, Michigan College of Min. & Tech Houghton, Mich. '35 Ambrosiani, F. Peter, Student, Michigan College of Min. & Tech Houghton, Mich. '36 Andersen, Burton Lee, Student, School of Mines, Univ. of Washington Seattle, Wash. '36 Anderson, Carlos, Student, Univ. of Oklahoma Norman, Okla. '36 Anderson, J. Wendell, Student, Pennsylvania State College State College, Pa. '36 Anderson, Joseph S. Cornelia Hotel, Ajo, Ariz. '35 Anderson, R. C., Student, Univ. of Washington Seattle, Wash. '35 Anderson, Roy A., Student, Washington State College Pullman, Wash. '35 Anderson, Willard. Student. Univ. of Oklahoma Norman, Okla. '36

Jan 1, 1936

By W. M. Brown

SEQUACHEE Valley includes portions of the counties of Marion, Sequachee, Bledsoe and Cumberland. It extends in a general direction parallel with the Great Valley of East Tennessee, some 75 miles northward from the Alabama state line. It is separated from the Valley of East Tennessee by a mountain arm about a dozen miles wide, known as Wallen's or Walden's Ridge. The genesis of the valley, geologically speaking, is simple. It is an erosion-valley along the axis of an anticlinal. The point of the wedge remains in a row of low "saw-tooth" hills, running up the center of the valley. These hills are of Lower Silurian age, and consist of Trenton limestone, covered and protected in some measure by chert. Walls of Carboniferous age form the inclosing mountains on either side; whilst a magnificent arch of Hudson River, Niagara, Hamilton and Subcarboniferous strata closes the valley at the

Jan 1, 1886

By J. Husson, R. Iffly, M. Gondouin

A systematic variation of well deliverability, as reflected from isochronal back-pressure tests performed at regular intervals, has been observed in some gas condensate wells producing at high rates. The same effects have been obtained using a numerical model of gas and condensate flow which takes into account secondary gasoline deposited in the pore space as a result of pressure reduction, and non - Darcy flow of gas in the vicinity of the wells. Matching calculated values with previous test results has been possible, and future predictions have been obtained. An application of this method to the Hassi Er R'Mel gas-condensate field in Algeria is tentatively shown. INTRODUCTION Flow capacity of gas wells is generally derived from an analysis of back-pressure tests. The empirical equation q = C (?p2)n used by Rawlins and Schellhardtl can be derived rigorously assuming that steady-state radial flow of a dry gas of constant viscosity and compressibility is established during each flow period of the well tests. Furthermore, when Darcy's law applies in the entire flow region, the theory predicts that the exponent n is equal to 1. In low-permeability reservoirs, it was soon discovered that the time required to reach a stabilized flow often exceeded the duration of the flow periods normally available for testing wells. Consequently, transient gas flow had to be considered instead of the steady-state assumption previously used. This led to the isochronal testing procedure established by Cullender2 which has largely replaced conventional back-pressure testing. For dry gas fields, this method yields definite values of C and n equivalent to those of the empirical equation. These values should remain constant for each well as long as the permeability of the formation and the characteristics of the gas (viscosity and compressibility) do not change appreciably. This is the case when reservoir pressure remains -close to the original value and when the formation near the wellbore remains free of plugging. Under those conditions, stabilized flow potential curves of gas wells can be established from a single sequence of isochronal flow and shut-in periods. An analysis of a pressure build-up following a longer production period provides additional data on the transmissivity (k h/ u) of the reservoir, and eventually on the 'drainage radius rd of the well, which can be related to the value of C so that future performance of the well can be predicted using the concepts developed by A. Houpeurt.3 At high flow rates, Darcy's law no longer applies in the vicinity of the wellbore, and inertial effects in the high velocity gas flow introduce additional pressure drops. As a consequence, exponent n of the backpressure tests becomes smaller than 1, and a slight curvature of the log-log plot of ?p2 vs q can be predicted when going from very low to high rates of flow (Elenbaas and Katz).5 The effects of variations of viscosity and compressibility with pressure on the radial flow of dry gas in an infinite reservoir were taken into account by Jenkins and Aronofsky.7 Numerical solutions of the transient flow of an ideal gas in finite radial reservoirs were presented by Bruce, Peaceman, Rachford and Rice.8 In the case of gas condensate wells, however, the presence of gasoline in the pore space as soon as reservoir pressure is reduced below the dewpoint pressure further complicates the interpretation of flow tests so that the prediction of stabilized well performance becomes very difficult. Field observation shows that both C and n derived from isochronal tests vary in time, even when reservoir pressure has not changed appreciably. Such a variation cannot be attributed to any change of the gas characteristics, and must result from the effect of a gasoline saturation on the gas flow.

By H. C. Chang, N. J. Grant

Creep of very coarse grained high purity aluminum was studied at 400°, 700°, and 1100°F at initial stresses of 50 to 1200 psi. Local strain measurements were made across the grain boundaries and in different regions of various grains during creep, thereby permitting the drawing of component creep curves. The relative amounts of elongation as measured across a grain boundary and in the grains adjacent to the boundary depend on the temperature of testing. The significance of creep curve equations and activation energies is discussed. THIS paper presents some of the results of a research program devoted to the study of the mechanism of creep in high purity aluminum. Previous publications have dealt with the cyclic processes of alternating grain boundary sliding and migration, and the deformation in the grains caused by these processes;' the direction and the driving force of grain boundary sliding and migration;' the deformation in the grains and the restricting effects of the grain boundaries on this deformation." These previous papers were based mainly on either microscopic observations or X-ray data, or both. Sometimes creep curves across two closely spaced reference marks (about 0.6 to 0.7 mm apart) were also presented with a view to correlating the elongation values with the optical observations in general, and with certain deformation processes in particular. These curves shall henceforth be referred to as component creep curves. No attempts were made, however, to compare either the component creep curves which were obtained in different regions of a specimen, or those obtained from different specimens subjected to different creep test conditions. It is the purpose of this paper to present these component creep curves. Among the factors influencing the behaviors of these curves, those studied were stress, temperature, and grain arrangements in the specimens. It is proposed to show how greatly the deformation can vary from grain to grain and within an individual grain in a coarse grained specimen. The experimental technique and procedure have been presented.' It remains necessary to emphasize that the reference marks were produced by pressing a thin sewing needle into the surface of the specimen before the final annealing at 900°F for 24 hr and at 1150°F for 12 hr. The cold work around the needle indentations was therefore removed. The depth of these holes after electropolishing the annealed specimens was about 0.01 mm. This depth and area were negligible in comparison with the thickness of the specimens, 2.3 mm, and hence would not affect the creep behavior. Results Fig. 1 shows a development diagram of specimen P-8. The dots on the surface locate the needle point reference marks used to obtain the component creep curves. A curve obtained between two dots across a grain boundary measures not only the boundary deformation but also the deformation associated with boundary sliding occurring in the grains in the region between these indents. The original distance between two reference marks was about 0.6 to 0.7 mm. The maximum error of measurement was 0.01 mm, or in terms of percentage elongation, of the order of & 1.5 pct. Whereas the component creep curves shown in the figures to follow were drawn as a gross average of the points, in view of the fineness of some of the steps of grain boundary sliding and migration, as shown in the previous publications,¹,2 it appears logical to expect that some of the finer cycles of movement have not been delineated for the strain sensitivity of the measuring system. It seems justifiable to say that the curves are not as smooth as shown. 700°F Tests: Fig. 2 shows component creep curves across four of the grain boundaries in specimen P-8, tested at 700°F and 85 psi. These curves clearly show alternate cycles of increasing and decreasing

Jan 1, 1954

By D. E. Hartman, J. M. Roberts

A detailed study of the temperature dependence of the critical stress, TB . necessary to cause a damping loss of 1.41 x 10-6 g mm per mm3 in pre-strained magnesium single crystals has been carried out in the temperature range 82" to 320°K. Tb is found to be linearly related to the reciprocal of the ahsol~cte temperature in this temperature range. The temperature dependence of the anelastic limit, TA, defined as the stress necessary to form open unidirectional stress-cycle damping loops has been measured between 82" to 320°K. ta is found to be independent of temperature in this range. It is suggested that TA is determined by the stress necessary to activate Frank-Read dislocation NUMEROUS studies1-9 have been reported concerning the details of yielding and microstrain near and below the generally discussed macroscopic flow stress. The work of Kramer and coworkers10-13 is helpful in determining certain qualitative facts. concerning preyield phenomena. The absence of a stress-dependent delay time in annealed copper and aluminum single crystals between 83" and 298 suggests that the preyield mechanism is temperature-independent in this range. This is not sources. The temperature and stress dependence of the effective activation volume (Veff) has been measured in the damping-loop region in prestrained magnesium single crystals. The data suggests that Veff/kT is approximately constant, equal to 2 4.5 sq mm per g in the temperature range 130°to 298°K, and that Veff is almost independent of stress at stress levels greater than 10 g per sq mm. A restricted model is developed to predict the stress (rb) necessary to cause a small fixed damping loss as a function of temperature, effective activation volume, and dislocation density. Various possible dislocation mechanisms controlling TB are discussed. true for zinc, p brass, and iron crystals in the same temperature range, however, since the existence of a stress-dependent delay time suggests a thermally activated preyield mechanism in these materials.10-13 The work by Vreeland et a1.14 confirms the work by Liu et al.ll on delayed yielding in zinc single crystals. A stress-dependent delay time between 82" and 298°K was found12 in prestrained aluminum and copper crystals. These results suggest that the preyield phenomena may be different between prestrained and unstrained or annealed crystals. The temperature dependence of the yield point at 2 x 10-8 plastic strain found by Rosenfield and Averbach3 in annealed copper and aluminum is not in agreement with the delay-time data, unless possibly the delayed yielding experiment only de-

Jan 1, 1964

By H. W. McQuaid

IT IS usually assumed that chemical specifications are sufficient for steel to be used for case carburizing, and if the steel analyzes within the ordinary limits specified for steel for this purpose, no difficulty traceable to the steel used should be encountered in obtaining satisfactory results in the case carburizing and hardening. Much work has been done to determine the effect of various alloying elements on the rate of carbon penetration, etc. but, to our knowledge, little if anything has been published in regard to the effect of the quality of the steel on the final results in the hardening of case-carburized steel parts. The writers believe that the structure of the case both before and after quenching is greatly affected by the actual condition of the steel itself as made, and that for good results in the case-carburizing and hardening departments, the steel should be of the best possible quality as regards non-metallic impurities. It is the purpose of this paper to prove that the presence of excess dissolved oxides in the steel, as made in the melting furnace, affects permanently the results obtained in carburizing and hardening and that it is possible that the presence of dissolved oxide can result in total unfitness of low-carbon steel for, case hardening purposes. When races and rolls for roller bearings are made from a low-carbon steel, case carburized and hardened, it is of primary importance that the results of this treatment be of the highest quality. It is necessary, therefore, that in the case-carburizing work each detail be rigorously checked to avoid any defects which would cause the loss of much time and material. The case carburizing with which this paper deals was done in under-fired oil furnaces. The temperature of each furnace is controlled by means of a platinum platinum-rhodium thermocouple, in connection with a potentiometer indicator and potentiometer recorder. The temperature of each furnace is registered every 15 min. by an operator, who is continually checked by the automatic recorders.

Jan 2, 1922

Jan 1, 1936

Jan 1, 1936

By Stanley Herold

Considerable interest has been shown, during recent years, in the possibilities of developing oil fields in the South American Republics, now that the exhaustion of our present fields can be seen in the not very distant future. The demand for fuel oil and its products has been increasing far more rapidly than our increment of production during the last few years. Increase of consumption has been largely curtailed by the lack of sufficient supply. The main factors that have contributed to our previous neglect of the southern fields have been as follows:, (a) Lack of sufficient demand for the product. (b) Competition with producing fields, having large production, low cost, and better geographical position, such as Tampico, Mexico. (c) Greater interest in home fields with ready market at hand. (d) Our ignorance of southern economic and geologic conditions, clue to the distance between those areas and our financial centers. (e) Economic conditions in the southern countries, necessitating high costs of exploration and exploitation of the fields.

Jan 9, 1918

IN comparing the living conditions of the worker or peasant of the past with those existing today, his-torians might point out many strange contrasts. From the Doomsday Book we learn that at the time of Wil-liam the Conqueror the 1,375,000 inhabitants of Eng-land and Wales owned less than 1000 horses and 5000 oxen. Even as recently as 1871 when England and Wales had a population of 31,845.000, the total number of horses in the country was estimated at 1,110,000. Compare the necessary drudgery of labor in those days with conditions in Canada today where a population of less than ten million people own 3,500,000 horses. Re-member that there is also a turbine installation in` this country of more than four million horse-power, besides steam boilers and locomotive and automobile engines which reduce the traction and hand labor of the farm and factory. Frequently, poetic license has glossed over the poverty and hardship of the common people in the "good old days," and the imagination has created an idyllic world, far from being justified by the condi-tions which actually prevailed. Simon Patten's de-scription of the Middle Ages as "A Thousand Years Without an Ice Box" came nearer portraying the true situation. No one is likely to forget that the discovery of America was an incident in Europe's attempt to find a short route to the Indies, but the fact is usually for-gotten that the summer diet in Europe in 1400-an ice-less age-was such that spices were more precious than gold. Though the glamor of the Indies may never sur-round the modern refrigerator, certainly the modern housewife is likely 'to feel that the applied art called "cookery? may attain to higher levels with the assist-ance-6f such an adjunct. Those who have spoken slightingly of the uniformity of the modern apartment and have eulogized some of the exceptional hand-made furniture which has been bequeathed by former generations, have failed to com-pare modern house furnishings with those in the typical peasant's hovel. Machine-made furniture, though with-out particularly good lines, contrasts quite favorably with the pile of rags in the corner, and the poorest gas or oil stove is better than an open fire on a dirt floor. The scientist's application of the theories of physics, chemistry, biology and mathematics .to practical prob-lems has brought about a series of kaleidoscopic trans-formations in agriculture, industry and commerce. Large scale production, improved means of communica-tion and the prevailing higher standard of living are terms which imply a very human meaning when in-terpreted as actual changes in individual living. Though the student and the teacher may deprecate the influence of commercialism upon science, humanity as a whole has received great benefits from the close relationship which has developed between science and industry, and industry in turn has done much for science through the building and endowment of laboratories and by supply-ing funds to maintain research workers.

Jan 11, 1927

Jan 1, 1934

Jan 1, 1938

Jan 1, 1942

By M. F. Trice

Pyrophyllite is a hydrous aluminum silicate (A1²Si4O10(OH)²)1 that, occurs in both the foliated and the massive forms. The foliated variety resembles talc in that it has a greasy feel, a pearly luster, perfect basal cleavage, and usually is white, although in some deposits apple green, gray, brown, russet, and nearly black specimens may be found. The massive deposits of pyrophyllite yield pearl gray to light tan aggregates, some of which are so friable that they may be crushed with the hands into a fine gritty powder. Frequently specimens of the massive variety are studded with crystals of radial structure. The mineral has a specific gravity of about 2.7 and a hardness of 1 on Mohs' scale.' The chemical composition of commercial pyrophyllite reflects the mineralogy of the deposits, which, according to Stuckey12 contain pyrophyllite and quartz, together with chloritoid, sericite, and a few other minerals of negligible importance. The latter, he says, ('are noticed in but small quantities to the extent they might occur as accessory constituents of an igneous rock or as products of regional metamorphism or weathering. . . . Quartz is abundant everywhere except in the very best grades of pyrophyllite." Analyses of specimens from several deposits are listed in Table 1, showing that the silica content varies from 57 to 73 per cent and the alumina from 22 to 33 per cent. Oxides of iron and the alkaline metals are collectively present, with one exception, to an extent of about 1 to 1.5 per cent. Sources At present, North Carolina is the only commercial source of pyrophyllite, although the mineral has been found in small quantities in many parts of the world. The North Carolina deposits are in the "Carolina Slate Belt," which traverses the center of the state in a southwesterly direction. This belt varies from 8 to 50 miles in width. Two major deposits of pyrophyllite lie along its eastern boundary, in what is known as the Deep

Jan 1, 1942

By M. F. Trice

Pyrophyllite is a hydrous aluminum silicate (A1²Si4O10(OH)²)1 that, occurs in both the foliated and the massive forms. The foliated variety resembles talc in that it has a greasy feel, a pearly luster, perfect basal cleavage, and usually is white, although in some deposits apple green, gray, brown, russet, and nearly black specimens may be found. The massive deposits of pyrophyllite yield pearl gray to light tan aggregates, some of which are so friable that they may be crushed with the hands into a fine gritty powder. Frequently specimens of the massive variety are studded with crystals of radial structure. The mineral has a specific gravity of about 2.7 and a hardness of 1 on Mohs' scale.' The chemical composition of commercial pyrophyllite reflects the mineralogy of the deposits, which, according to Stuckey12 contain pyrophyllite and quartz, together with chloritoid, sericite, and a few other minerals of negligible importance. The latter, he says, ('are noticed in but small quantities to the extent they might occur as accessory constituents of an igneous rock or as products of regional metamorphism or weathering. . . . Quartz is abundant everywhere except in the very best grades of pyrophyllite." Analyses of specimens from several deposits are listed in Table 1, showing that the silica content varies from 57 to 73 per cent and the alumina from 22 to 33 per cent. Oxides of iron and the alkaline metals are collectively present, with one exception, to an extent of about 1 to 1.5 per cent. Sources At present, North Carolina is the only commercial source of pyrophyllite, although the mineral has been found in small quantities in many parts of the world. The North Carolina deposits are in the "Carolina Slate Belt," which traverses the center of the state in a southwesterly direction. This belt varies from 8 to 50 miles in width. Two major deposits of pyrophyllite lie along its eastern boundary, in what is known as the Deep

Jan 1, 1942

Jan 1, 1893

Jan 1, 1932

By Paul A. Farrar, Felix Ermains, Harold Margolin

The systems Ti-Crand Ti-Vhave been reinvesti-gated in the region up to 40 wt pct alloying addition using both conventional and rapid quenching techniques. The Ti-Cr eutectoid temperature was determined to be at 667° & 10° C and 14.5 wt pct Cr. The solubility of the Cr in a Ti was found to be less than 1 pctat 700"C. The P transus of the Ti-V system was found to be depressed to 510°C at 40 wt pct V and the solubility of V in a Ti was found to be less than 2 wt pct at 700°C. Investigation by a. d. McQuillan1-3and m. k. McQuillan4 on the systems Ti-Co, Ti-Cr, Ti-Cu, Ti-Fe, Ti-Mn, Ti-Ni, and Ti-V has cast doubt as to the position of the ß/a + ß boundaries in many of these systems. Their investigations were carried out using hydrogen pressure and/or rapid quenching experiments, as opposed to the conventional quartz capsule techniques employed by most other investigator.'" By these methods, the ß/a + ß boundary was found to be lower than that obtained by conventional techniques in all except the Ti-Fe system. In the latter, the ß/a + ß boundary was essentially the same as the boundary obtained by conventional technique.7' On the basis of rapid quenching results in the Ti-Cr system, M. K. McQuillan4 placed the eutectoid temperature below 550°C whereas other investigations using conventional techniques had placed the eutectoid variously as between 650' and 700°C,5 between 675' and 700°C,6 between 650" and 675°C,7 at 670°C,8 and above 625"C.la9l3 In order to check these results, a reinvestigation of four of the systems was undertaken using both conventional and rapid-quenching techniques. The Ti-Fe and Ti-Mn systems will be dealt with in anoth er paper, with only the Ti-Cr and Ti-V systems being discussed here. EXPERIMENTAL TECHNIQUES Alloys employed for the delineation of the systems under investigation were prepared from iodide titanium sheet capsules containing the alloying materials,

Jan 1, 1962

By M. Gensamer

ONLY recently has it been realized that preferred orientations are common in hot-rolled steels. In a recent paper, N. P. Goss1 stated that hot-rolled mild steel exhibits a texture different from that charac-teristic of cold-rolled steel. No complete study of these hot-rolling textures has been reported using the pole-figure method of Wever. The material used in the work reported in this paper was the same material used by Gensamer and Mehl2 in a recent study of preferred orientations in cold-rolled steel, to which reference may be made for the composition and thermal history of the steel. Automobile-body sheet bar, 4 in. thick was hot-rolled at two temperatures, 780° and 910° C. (1436° and 1669° F.). (These temperatures refer to the tempera-ture of the furnace in which the steel was heated.) After each pass the steel was returned to the furnace and held there long enough to return to temperature. Although no accurate method was used to measure the temperature after each pass, it was estimated by color that only a slight drop in temperature occurred. In order to determine the effect of any preferred orientation that might have persisted through the normalizing treatment, one specimen at each temperature was rolled in the same direction as the original working direction and the other at right angles to it. The total reduction in each case was 85 per cent, the specimens having been reduced from 0.250 to 0.0375 in. in five passes. Final cooling was in air. Pinhole reflection photograms were taken of all four specimens, with the rolling direction vertical and the X-ray beam at an angle of 7° with the transverse direction (the transverse direction is defined as that direction in the rolling plane perpendicular to the rolling direction). These photograms, taken with a Me target at 35 kv., are reproduced in Figs. 1, 2, 3 and 4. They show that a more pronounced texture was developed by the low-temperature rolling (780° C.), and that of the two

Jan 1, 1936