Search Documents

By Alexander Deussen

The figures listed in a table for Gulf Coast fields given by L. P. Teas1 in 1934 are so greatly at variance with results that I have obtained from a serious study of this subject over a number of years, that I am disposed to challenge the correctness of Mr. Teas' figures as an accurate representation of acre-foot yields of Gulf Coast fields, and as regards at least two of the fields listed by Mr. Teas I desire to "put into the record" some figures that, according to my study, are more nearly in accord with what I conceive to be the actual facts. Upon investigation I find that Mr. Teas' figures, inadvertently no doubt, arc not what they purport to be. Apparently the figures were arrived at by considering as thickness of the producing formation the net thickness of producing rock corresponding "to the total of the net portions of the producing zones which actually yield oil into the drill hole"—and in following this method I am under the impression that Mr. Teas was acting under instructions of the Institute in the preparation of this paper, in order to get comparable figures from the several fields of the United States. Apparently the author interpreted these instructions to mean that in the absence of cored thicknesses of producing horizons the actual number of feet of screen set in the various producing zones was to be taken as the basis for arriving at the thickness of these zones and the "acre-foot" yields. It is obvious that in many instances only 20 ft. of screen, or even 10 ft. of screen, might be set in a well, when there might be actually 100 ft. of oil sand present. In the early operations in the Gulf Coast it was usual to set much less screen than the amount of sand. It follows that the "acre-foot yields" so arrived at would be much greater than those found by using the full amount of sand. In Mr. Teas' table, it was indicated that up to the end of 1933 "acre-foot" yields had been obtained in the several fields as listed in Table 1. A casual inspection of these yields will show that certainly they do not properly reflect the amount of oil produced from an acre-foot of the

Jan 1, 1936

By Max Roesler

W. L. CUMINGS,* Bethlehem, Pa. (communication to the Secretary+). -In this discussion of Mr. Roesler's paper, I shall follow Kemp in using the term "granite" to refer to the acid rock called syenite by Kimball. Diorite, as I understand it, is the dark basic rock invariably closely associated with the orebodies. The types of rock of intermediate composition, mainly intrusives, are not under discussion. It is difficult for me to conceive that this granite is the ore-bearing agent, for the following reasons: 1. No isolated orebodies in the granite are known. It would seem that if this rock is the mineralizer, some small bodies, or at least patches and small masses of ore so situated would exist. 2. In 1909 the writer conducted explorations on the Pequena and Grande claims about 1 mile north of West Mine No. 5. This work was done after a very careful magnetic survey had shown a large and uniform area of attraction. As exploration progressed, it became evident that in this case the magnetic attraction was due to disseminated magnetite. Much ore of 40 per cent. Fe was found, but very little commercial ore was shown up. This ore was entirely in the diorite and no granite outcrops are near. The occurrence could easily have been described as "ore formation but very little ore." I cannot conceive how a remote granite intrusion could impregnate a diorite mountain with 40 per cent. of Fe, and prefer to believe that this 40 per cent. of iron was in its real home, rather than in a sort of dioritic "boarding house" after having been evicted by granitic parents. 3. The Ocaña mine, which has produced nearly 500,000 tons, shows no evidence that the granite is the mineralizer. This is admitted by Mr. Roesler on p. 1827. 4. I believe it will not be disputed that all the iron-ore deposits extending along the south coast for 60 or 70 miles are of a similar origin. Evidence available at other points might properly be referred to in discussing the article under review. At the La Plata mines, about 60 miles west of Santiago, the writer has also made explorations. No granite is in evidence. At one point in the bed of a creek is a small body of magnetite about 10 ft. long, entirely surrounded by a hard fresh diorite. To me

Jan 3, 1917

By Francis Donaldson

THE direct injection of cement grout into water-bearing fissures as a means of checking or stopping the flow of water into shafts and tunnels has been experimented with for a decade or longer and seems to have been first attempted in Europe. The earliest application of which the writer has found a record was at a shaft sunk by the Mining Society of Lens; this is described by C. Dinoire in the Transactions of the Institution of Mining Engineers.1. It is only lately, however, that the process has been entirely successful. This success has been accomplished on the Catskill Aqueduct, now under construction by the city of New York. This aqueduct includes a number of deep pressure tunnels, reached by shafts for both waterway and construction purposes. In portions of these shafts and tunnels considerable underground water was met. The contract for the first of these deep pressure tunnels was let to the T. A. Gillespie Co.; this section is known as the Rondout Siphon. It leads under the Rondout valley at a depth of from 400 to 800 ft. and is about 5 miles long. The engineers expected that considerable water would be encountered, but fortunately this was not the case except at one shaft, known as No. 4, which penetrated the rock at a junction between limestone and conglomerate. Water-bearing fissures were encountered almost immediately. At a depth of about 200 ft. a flow of 1,500 gal. per minute was struck. The shaft then contained as many pumps as could be used, and it seemed impossible to sink it further. After vain efforts had been made to proceed, John P. Hogan, a division engineer of the Board of Water Supply, suggested that cementation of the fissures be tried. The process was attempted for the first time in this country. Since the shaft was partly full of water it was necessary to drill grout holes with a diamond drill. Platforms were placed on the timbers at the water level, the diamond drill was installed and six 90-ft. holes were drilled in the bottom of the shaft. Several car loads of cement were pumped through these holes into the fissures, the drill casings being used for grout pipes. This largely cut off the flow of water from the bottom and sinking could then

Jan 1, 1914

By Sadtler, C. B.

IT is generally assumed that in most metals and alloys a given tensile stress produces a given deformation irrespective of the length of time during which the stress is applied. This assumption is justified in most of the important engineering applications of metallic materials; however, in the case of some metals and alloys used or tested at temperatures over or slightly under that at which recrystallization can occur the assumption is not warranted.1 This paper deals with the variations of deformation produced by a constant tensile stress acting for varied lengths of time in the special case of thin aluminum alloy sheet of the duralumin type, which had been subjected to different thermal and mechanical treatments. The material investigated was in the form of a sheet approximately 0.002 in. thick, which had been cold-rolled from a thickness of 0.020 in. It has been found that at a sufficiently high constant tension such material deforms continuously with the elapse of time and that the rate at which this deformation occurs is greatly influenced by the previous thermal and mechanical treatments.

Jan 1, 1927

By M. S. Burton, B. W. Christ, G. V. Smith

Evidence of the effects which high-angle grain boundaries and veining subgrain boundaries have on the yield phenomenon of zone-refined iron is reported. Room-temperature tensile tests on 50-mil wive at several gram sizes produced upon recrystallization at diffevent temperatures below 910C (a-y phase-transfornzatzon temperature) show that upper and lower yield stress decrease with increasing grain size. The upper yield point effectively disappears at grain sizes of 81 and 102 u in samples of this diameter. However, samples of 129 p grain size. produced during recrys-tallization at 950°C, exhibit a pronounced upper yield point and an increased lower yield stress. Possible causes of the reversal in the grain-size dependence of yielding are discussed. Veining substructure, detected with picval-HC1 etchant, but not with 2 pct nital, is formed during the a-y transformation, and is believed to account for the observed effecls. The strengthening associated with high-angle boundaries in zone-refined tron is discussed in terms of: 1) the stress dependence of slzp multiplicity, and 2) the stress dependence of dislocation emission from grain boundaries. WIDE use of transmission electron microscopy and dislocation etch-pitting techniques has led to a growing awareness of the presence of dislocation substructures in annealed pure metals. Whereas much speculation'-4 has developed about the influence which subgrain structures have on the mechanical behavior of metals, particularly the yield strength, only limited experimental evidence correlating subgrain structures with lower yield strength has been presented. 2,3,5-7 It is the purpose of this note to present experimental evidence of the effects which grain boundaries and subgrain boundaries have on both the upper and lower yield strength of zone-refined iron. Effects due to high-angle boundaries formed upon recrystallization below the a-y phase transformation are compared with effects due to veining subgrain boundaries formed upon "recrystallization" above the a-y phase-transformation temperature. These effects are further compared with the reported influence 2,3,5-7 which low-angle boundaries have on the lower yield strength of bcc transition metals. EXPERIMENTAL PROCEDURE The starting material for these experiments was a 1-in.-diam zone-refined ingot prepared at Battelle Memorial Institute. Initial purification of electrolytic iron by vacuum-induction melting was improved by a floating zone-melting treatment in ultrapure hydrogen.' Chemical analysis of this zone-refined iron appears in Table I. Tensile samples of 50-mil wire were prepared by rolling and drawing portions of the ingot. An intermediate recrystallization anneal at 625°C after rolling to a reduction in area of 85 pct was carried out in an evacuated Vycor capsule (10-=5 mm Hg). Further reduction in area of 91 pct was followed by recrystallization in evacuated Vycor capsules at temperatures between 600" and 950°C, see Table 111. All samples

Jan 1, 1967

By L. H. Levenson, Charles S. Barrett

Numerous determinations1-' of the texture of cold-rolled polycrystalline iron, steel, and ferritic alloys have been made with good agreement among the various observers as to the principal features of the texture common to all, but there has been no adequate explanation of the texture in terms of, the behavior of individual grains. This study presents an explanation of the texture based on the observed rotation of single crystals when deformed in a manner similar to a grain in the aggregate, a method we have found useful in leading to a better understanding of compression and tension textures;8,9,10 in particular, the aim has been to determine experimentally the end orientations of rolled single crystals of iron. These are discussed in connection with the point of view of Weverl and of Boas and Schmid2 that the rolling texture is a simple compression texture (compression normal to the rolling plane) superimposed on a simple tension texture (tension in the rolling direction), and the point of view of Kurdjumow and Sachs3 that three ideal end orientations exist. Experimental Method The single crystals used were in the form of disks cut from a stock of crystalst pre- pared in this laboratory by a strain-anneal method from mild steel decarburized and purified in hydrogen, the details of which have been described elsewhere.11 To ensure maximum elongation in the rolling direction and to simulate approximately the rolling of a grain in an aggregate, lateral flow was constrained by placing each crystal in a close-fitting hole in a plate of copper or iron of equal thickness and rolling the plate and crystal together. About one-third of the crystals were rolled in a "sandwich" pack by adding top and bottom cover plates. The two-high mill used had 8-in. diameter rolls and was operated at 15 r.p.m. The initial diameter of the crystals was between 1/4 and 1/2 in., while the starting thickness varied from 0.031 to 0.376 in. With a single exception, which was rolled 63 per cent, the crystals were rolled to a final reduction in thickness of 82 to 97 per cent in 20 to 40 passes, alternately changing the sense of the rolling direction. The initial orientations of the crystals were determined either by X-ray back reflection12 or by optical reflectionl3 from etch pits; the mean final orientations were determined by X-ray Laue photograms using molybdenum, silver, or tungsten radiations, by optical reflection, and in many cases by both methods. Results Twenty-six crystals were studied. It was found that there were three typical be-

Jan 1, 1941

By Charles S. Barrett, L. H. Levenson

Numerous determinations1-' of the texture of cold-rolled polycrystalline iron, steel, and ferritic alloys have been made with good agreement among the various observers as to the principal features of the texture common to all, but there has been no adequate explanation of the texture in terms of, the behavior of individual grains. This study presents an explanation of the texture based on the observed rotation of single crystals when deformed in a manner similar to a grain in the aggregate, a method we have found useful in leading to a better understanding of compression and tension textures;8,9,10 in particular, the aim has been to determine experimentally the end orientations of rolled single crystals of iron. These are discussed in connection with the point of view of Weverl and of Boas and Schmid2 that the rolling texture is a simple compression texture (compression normal to the rolling plane) superimposed on a simple tension texture (tension in the rolling direction), and the point of view of Kurdjumow and Sachs3 that three ideal end orientations exist. Experimental Method The single crystals used were in the form of disks cut from a stock of crystalst pre- pared in this laboratory by a strain-anneal method from mild steel decarburized and purified in hydrogen, the details of which have been described elsewhere.11 To ensure maximum elongation in the rolling direction and to simulate approximately the rolling of a grain in an aggregate, lateral flow was constrained by placing each crystal in a close-fitting hole in a plate of copper or iron of equal thickness and rolling the plate and crystal together. About one-third of the crystals were rolled in a "sandwich" pack by adding top and bottom cover plates. The two-high mill used had 8-in. diameter rolls and was operated at 15 r.p.m. The initial diameter of the crystals was between 1/4 and 1/2 in., while the starting thickness varied from 0.031 to 0.376 in. With a single exception, which was rolled 63 per cent, the crystals were rolled to a final reduction in thickness of 82 to 97 per cent in 20 to 40 passes, alternately changing the sense of the rolling direction. The initial orientations of the crystals were determined either by X-ray back reflection12 or by optical reflectionl3 from etch pits; the mean final orientations were determined by X-ray Laue photograms using molybdenum, silver, or tungsten radiations, by optical reflection, and in many cases by both methods. Results Twenty-six crystals were studied. It was found that there were three typical be-

Jan 1, 1941

By M. S. Abrahams

Germanium has been rolled in the temperature range of 700o to 800°C. The thickness has been decreased by as much as a factor of four, from a thickness of 0.032 in. to a thickness of 0.008 in. For deformations below 60 pet, the true strain per pass is found to be a constant; from the temperature dependence of this slope, an activation energy of about 2.5 ev is obtained. This energy agrees with that for dislocation climb in germanium . For reductions greater than 60 pet, complete rings are seen in the Lave photographs, new grains are observed in the microstructure, considerable softening occurs, and the hole mobility is very low. This evidence indicates that the recrystallization of gertnanium has occurred. GERMANIUM has been deformed in many ways1 including tension, compression, torsion, and bending since Gallagher2 first described its plastic nature at elevated temperatures. All of these studies indicate that the glide plane in germanium is (111) and that the glide direction is (110). Rolled germanium specimens were used by Kolm, Warekois, and Kulin3 in their X-ray study of deformed semiconductors, but no information is given on the rolling itself. The present experiments deal with the rolling of germanium at various temperatures and for different orientations. In all previous deformation studies, the phenomenon of recrystallization (i.e., the transformation of a single crystal into a polycrystal) in germanium has not been observed4 despite relatively large deformations at elevated temperatures. The proposed reason4 for this was that sufficient energy could not be stored in the deformed germanium lattice. In contrast to the earlier studies this work will present evidence indicating that recrystallization occurs in germanium during rolling at an elevated temperature. I) EXPERIMENTAL PROCEDURE A) Test Specimens. The samples used for rolling were in the form of rectangular parallelepipeds measuring 0.3 in. long, 0.06 in. wide, and 0.035 in. high. They were cut from an undoped single-crystal ingot of p-type germanium with a resistivity of 24.4 ohm-cm, a Hall mobility of 2300 sq cm v-' sec-l, and a hole concentration of 1.1 x 1014 cm"3 at room temperature. The surfaces of the specimens were metallographically polished prior to rolling. The initial dislocation density of the samples was about 10' cm-' as determined by etching in CP4. Two different specimen orientations were used. In the first case, the direction of rolling was parallel to (251), the surfaces in contact with the rolls were of the form (1021, and the normal to the third face was parallel to (211). The corresponding di-

Jan 1, 1964

By L. D. Woodworth, E. E. McGinley

During the past several years has occurred what, in the light of future events, may aptly be called the rebirth of the acid Bessemer process. The increased attention given to the technical and metallurgical details involved in the production of Bessemer steels has been exceedingly fruitful, and indicates the value of further research and p1ant development. In times like these, when the steelmaking capacity of the country is operating at a maximum rate to supply materials for the national defense program, it behooves the Bessemer operator not only to strive to increase production but also to maintain a high standard of quality. The opportunity is ripe, it seems, to recapture fields of application once considered the birthright of Bessemer steels, but supplanted in recent years by open-hearth grades. This involves cooperation all along the line, from the blast-furnace operator to the metallurgical contact man and salesman. The metallurgist's part in this program involves the study of the many steelmaking variables and the measures necessary to ensure constancy in the finished product. It is equally important that the knowledge gained be disseminated widely to ensure the wise application of Bessemer steels in new fields. The merits of Bessemer steels for certain work are well understood. The combined properties of good weldability, machinabil-ity and stiffness are unique and fully explain the strong entrenchment of Bessemer steels in certain fields; e.g., skelp for small butt-weld conduit, screw steels machined in automatics, and certain tin-plate applications. It is the purpose of this paper to review briefly the physical properties of Bessemer steels as contrasted with those of open-hearth steels, to discuss control measures now employed in the making of Bessemer steel, and to consider the advantages derived from the use of these control measures. Physical Properties oF Bessemer vs. Open-hearth Steels A number of Bessemer blows and open-hearth heats were tested for tensile strength, ductility and impact strength. The steels selected were confined to sections from 3/4 to 1 1/4-in. diameter, inclusive, and the carbon content covered was sufficient to yield parallel ranges in ultimate strength for the comparison. Other factors, such as the extent of deoxidation of the steel and variations in chemistry, were kept as comparable as possible. Machined test pieces of 0.505-in. diameter with an 8-in. gauge length were pulled. The data obtained are shown in Fig. I, ultimate strength being plotted against carbon content. This graph shows that for equivalent carbon content Bessemer steel has on the average 15,000 lb. per sq. in. greater tensile strength and, conversely, for the same tensile strength Bessemer steel requires on the average 0.14 per cent less carbon. The average phosphorus content for the Bessemer steel was 0.090 per cent,

Jan 1, 1941

By E. E. McGinley, L. D. Woodworth

During the past several years has occurred what, in the light of future events, may aptly be called the rebirth of the acid Bessemer process. The increased attention given to the technical and metallurgical details involved in the production of Bessemer steels has been exceedingly fruitful, and indicates the value of further research and p1ant development. In times like these, when the steelmaking capacity of the country is operating at a maximum rate to supply materials for the national defense program, it behooves the Bessemer operator not only to strive to increase production but also to maintain a high standard of quality. The opportunity is ripe, it seems, to recapture fields of application once considered the birthright of Bessemer steels, but supplanted in recent years by open-hearth grades. This involves cooperation all along the line, from the blast-furnace operator to the metallurgical contact man and salesman. The metallurgist's part in this program involves the study of the many steelmaking variables and the measures necessary to ensure constancy in the finished product. It is equally important that the knowledge gained be disseminated widely to ensure the wise application of Bessemer steels in new fields. The merits of Bessemer steels for certain work are well understood. The combined properties of good weldability, machinabil-ity and stiffness are unique and fully explain the strong entrenchment of Bessemer steels in certain fields; e.g., skelp for small butt-weld conduit, screw steels machined in automatics, and certain tin-plate applications. It is the purpose of this paper to review briefly the physical properties of Bessemer steels as contrasted with those of open-hearth steels, to discuss control measures now employed in the making of Bessemer steel, and to consider the advantages derived from the use of these control measures. Physical Properties oF Bessemer vs. Open-hearth Steels A number of Bessemer blows and open-hearth heats were tested for tensile strength, ductility and impact strength. The steels selected were confined to sections from 3/4 to 1 1/4-in. diameter, inclusive, and the carbon content covered was sufficient to yield parallel ranges in ultimate strength for the comparison. Other factors, such as the extent of deoxidation of the steel and variations in chemistry, were kept as comparable as possible. Machined test pieces of 0.505-in. diameter with an 8-in. gauge length were pulled. The data obtained are shown in Fig. I, ultimate strength being plotted against carbon content. This graph shows that for equivalent carbon content Bessemer steel has on the average 15,000 lb. per sq. in. greater tensile strength and, conversely, for the same tensile strength Bessemer steel requires on the average 0.14 per cent less carbon. The average phosphorus content for the Bessemer steel was 0.090 per cent,

Jan 1, 1941

By A. G. H. Anderson, A. W. Kingsbury

Silicon bronzes containing ken are used to a considerable extent in industry, under the trade name of P.M.G. alloys. Various classes of wrought alloys fall in the composition range 1.5 to 3.5 per cent silicon, and 0.5 to 2.5 per cent iron. Castings may contain as much as 6 per cent silicon and 3 per cent iron at present. The constitutional diagrams of these alloys are thus of considerable practical importance. Copper-silicon-binary alloys have been thoroughly investigated by a number of workers, the latest reports being those of C. S. Smith1 and of A. G. H. Andersen.2 Although much work has been done on iron-copper alloys,3 recorded investigations on the copper-rich copper-iron binary constitutional diagram are not numerous. Tammann and Oelsen4 etermined the solubility limits of iron in copper by means of magnetic measurements, and found that the solubility of iron in copper amounts to a fraction of one per cent at 400°C., increasing slowly to one per cent at 800°C. From 800°C., the solubility increases rapidly and attains 4 per cent at iioo°C. Hanson and Ford,5 using electrical resistivity measurements and the microscope, determined a somewhat different solubility limit. of earlier X-ray works on the copper-iron system, very little has been published. The work by Bradley and Goldschmidt6 on copper-iron-aluminum alloys includes some information on the copper-iron binary. These investigators conclude that substitution of iron in the copper lattice decreases the spacings, which is contrary to the evidence of the present work. Hanson and West? have investigated the ternary alloys of copper with iron and silicon. Although their diagrams are valuable contributions to the understanding of these alloys, they did not recognize the kappa phase,l,2,7,8 and their diagrams do not everywhere conform to the phase rule. The present work contains a check by means of X-rays of the solid solubility limit of iron in copper, and an X-ray investigation of the ternary-phase diagram, which, owing to present conditions, it became necessary to curtail considerably. Preparation of Samples Castings weighing about 75 grams were melted under vacuum. The charges were made up of ingot iron, copper cathodes from Laurel Hill, and refined silicon supplied by the Electrometallurgical Co. Alundum crucibles were generally used. The exceptions were alloys 77 and 78, which were melted in graphite crucibles. The ingots were annealed at 800°C. for one week, then samples were cut for chemical analysis. Longitudinal sections of the binary alloy ingots were hammered into plates 1/8 in. thick. Wherever possible, these plates were homogenized at temperatures ensuring

Jan 1, 1943

By A. G. H. Anderson, A. W. Kingsbury

Silicon bronzes containing ken are used to a considerable extent in industry, under the trade name of P.M.G. alloys. Various classes of wrought alloys fall in the composition range 1.5 to 3.5 per cent silicon, and 0.5 to 2.5 per cent iron. Castings may contain as much as 6 per cent silicon and 3 per cent iron at present. The constitutional diagrams of these alloys are thus of considerable practical importance. Copper-silicon-binary alloys have been thoroughly investigated by a number of workers, the latest reports being those of C. S. Smith1 and of A. G. H. Andersen.2 Although much work has been done on iron-copper alloys,3 recorded investigations on the copper-rich copper-iron binary constitutional diagram are not numerous. Tammann and Oelsen4 etermined the solubility limits of iron in copper by means of magnetic measurements, and found that the solubility of iron in copper amounts to a fraction of one per cent at 400°C., increasing slowly to one per cent at 800°C. From 800°C., the solubility increases rapidly and attains 4 per cent at iioo°C. Hanson and Ford,5 using electrical resistivity measurements and the microscope, determined a somewhat different solubility limit. of earlier X-ray works on the copper-iron system, very little has been published. The work by Bradley and Goldschmidt6 on copper-iron-aluminum alloys includes some information on the copper-iron binary. These investigators conclude that substitution of iron in the copper lattice decreases the spacings, which is contrary to the evidence of the present work. Hanson and West? have investigated the ternary alloys of copper with iron and silicon. Although their diagrams are valuable contributions to the understanding of these alloys, they did not recognize the kappa phase,l,2,7,8 and their diagrams do not everywhere conform to the phase rule. The present work contains a check by means of X-rays of the solid solubility limit of iron in copper, and an X-ray investigation of the ternary-phase diagram, which, owing to present conditions, it became necessary to curtail considerably. Preparation of Samples Castings weighing about 75 grams were melted under vacuum. The charges were made up of ingot iron, copper cathodes from Laurel Hill, and refined silicon supplied by the Electrometallurgical Co. Alundum crucibles were generally used. The exceptions were alloys 77 and 78, which were melted in graphite crucibles. The ingots were annealed at 800°C. for one week, then samples were cut for chemical analysis. Longitudinal sections of the binary alloy ingots were hammered into plates 1/8 in. thick. Wherever possible, these plates were homogenized at temperatures ensuring

Jan 1, 1943

By Peter M. Fozzard

The San Bartolomt silver deposit was discovered by a United Nations team of geologists working with a counter- part team of staff of the Ecuadorian Government's General Directorate of Geology and Mines (DGGM). The Phase I project over five areas of operation during which this discovery was made was financed through a United Nations Development Program contribution of $860,000 and an Ecuadorian Government participation of about $680,000 equivalent. Existence of mineralization at San Bartolomé was first recognized in 1966 when a reconnaissance geochemical stream-sediment program was carried out over a 10 500 km2 (4,054 sq mile) area centered around the city of Cuenca in southern Ecuador. Over the course of this project more than 10,000 samples of stream-sediment, soil, and rock materials were collected. Average costs per sample were $10.00, as follows: collection, $5; sample preparation, $1.60; assay work, $3.40. Initially in the program (1965-1966) sediments were collected along all motorable roads and tracks. Routine analyses, originally by colorimetry and later by AAS, were for Cu, Pb, Zn and occasionally As, Ni, and Co. Discovery geochemical samples from the San Bartolomé drainage area were among the first to be taken in 1965. As luck would have it, the road along which this traverse was taken passes only some 100 m (328 ft) downstream from the mineralized suboutcrop. The relevant two streams sampled are of inconsequential size, some 1 m (3.3 ft) in width, with a limited flow volume throughout the year. Original anomalies were recognized through cold-extractable Cu/Zn analyses. The pH of all river waters was also recorded at sample sites. Resampling the discovery sediments when AAS became available showed total extractable values of between 150 ppm-300 ppm Zn, 550 ppm Pb, and 10 ppm Ag. In 1967 the first followup was by rough-and-ready means. Dithizone field-kits (THM) were used to rapidly test soils from the surrounding area. The area has no outcrop. This work allowed the definition of an area of interest of some 2 km (1.2 miles) x 500 m (1640 ft). Six approximately 1 km (0.6 mile) to 1.5 km (0.9 miles) lines spaced at approximate 250 m (820 ft) intervals were established and used for IP surveys and soil sampling at 50 m (164 ft) intervals. Where one of the lines crossed the westernmost geochemical discovery creek a first-priority geophysical anomaly coincided with a major Zn/Pb (and later Ag) soil anomaly. A pit was sunk and encountered mineralized vein material at a depth of 1.5 m (5 ft). This lucky glory hole confirmed the geochemical discovery and prompted systematic followup. Immediately, costeaning of the west bank of the discovery creek, the Quebrada Ocashuaico, was carried out and exposed weathered and leached mineralization. Nearly 100 mineralized veinlets ranging in thickness from 0.5 cm (0.2 in.) to 8 cm (3 in.) were exposed across the 180 m (59 1 ft) costean. Sixty mineralized veinlets were determined over a 90 m (295 ft) wide zone. Sampling delineated minable widths averaging between 0.16 and 0.31 kg/t (5 and 10 oz per st) Ag with associated copper (very sporadic) lead and zinc. Over the period 1968- 1972 a considerable amount of detailed work was completed: detailed IP, EM Turam, magnetic and mise-a-la-masse geophysics, very detailed soil- sampling, trenching, drilling and glory-hole drifting, and cross-cutting. Numerous problems were encountered: the area was found to be a most difficult geoelectrical target; zero outcrop; pyrite (nonargentiferous zones) associated with faulting; mineralized groundwater; extensive clay development; loss of diamond drill-core, and no two-dimensional surface information. As the program developed the complexity of the structure was slowly unravelled, using a degree of good guesswork. Apart from photogeological and ground geological mapping at various scales, the following

Jan 1, 1985

By W. R. Hibbard

It has been proposed1 on the basis of slip and flow that the ideal deformation texture of drawn wire for face-centered cubic metals is a (111) direction parallel to the wire axis. Under these considerations, an intermediate [loo] texture is permissible but should eventually change to the stable [Ill] orientation. This theory does not explain why copper and its alloys containing up to about 30 pct nickel, 5 pct zinc and 1 pct aluminum were found to have a double [Ill], [100] texture, while alloys with at least 8 pct zinc and 2 pct aluminum developed essentially a single [Ill] texture.1,2 It does suggest, however, that the [loo] component of the former alloys should disappear with additional deformation.3 Some evidence exists to support this suggestion. Howald4 reported that annealed copper wire previously drawn 93.8 pct and 98.5 pct developed a single [Ill] texture. Since, in wire, the drawn and annealed textures are similar, these wires probably had a single [Ill] deformation texture before annealing. In addition, although cold rolled polycrystalline copper and 80-20 brass were found to form different types of pole figures,5,6 single crystals of these metals when rolled from the stable (110) [112] orientation were found to produce essentially the same polo figure.7.8 It may be, therefore, that while the addition of solute elements changes the path by which the final texture is obtained, the final texture is not changed. Experimental Results The wires remaining from the previous investigation1 already drawn about 50 pct reduction in diameter were further drawn to 86 pct and then to 96.4 pct total reduction in diameter. The textures were determined after these stages by transmission X ray photograms taken with a copper K-alpha beam rotated 0 degrees toward the wire axis. It was found that the ratio of the [111].] and [100] intensities of the double texture in copper and its alloys containing 0.94 pct aluminum, 30.70 pct nickel, 2.61 pct zinc and 4.99 pct zinc increased from about 3:l for the 50 pct reduction to about 9:l for the 86 pct reduction. After 96.4 pct reduction, these wires exhibited essentially a single [lll] texture. Summary Thus, the drawn wire deformation texture of copper and its alpha solid solution alloys containing aluminum, nickel or zinc is essentially a single [Ill] texture as predicted by theoretical considerations of slip and flow.' For copper and its alloys containing up to about 1 pct aluminum, 5 pct zinc and at least 30 pct nickel, an intermediate [loo] component is found after about 50 pct reduction in diameter, but disappears after about 95 pct reduction in diameter. For alpha solid solution alloys containing at least about 2 pct aluminum and 8 pct zinc the single [Ill] texture is developed considerably more easily and is found after about 50 pct reduction in diameter. No explanation of this compositional effect is apparent. Similar work is contemplated for cold rolled and cold compressed alloys. References 1. w. R. Hibbard, Jr. and M. K. Yen: Trans. AIME 175, 126. Metals Tech., Feb. 1948, TP 2334. 2. W. R. Hibbard, Jr. and D. E. Trout, 11: Trans. AIME 185, 620. Jnl. of Melals, Sept. 1949, TN 18. 3. W. R. Hibbard. Jr.: Disc. of R. M. Brick's paper on Deformation Textures, ASM Symp. on Cold Working of Metals, Oct. 1948. 4. T. S. Howald: Disc. of Ref. 1. Trans. AIME, 175, 126. Melals Tech. Aug. 1948, TP 2449. 5. R. M. Brick, D. L. Martin and R. P. Angier: Trans. ASM (1943) 31, 675. 6. 0. Dahl and F. Pawlek: Zlsch. Melall. (1936) 28, 266. 7. C. S. Barrett and F. W. Steadman: Trans. AIME (1942) 147, 57. 8. J. E. Burke and C. S. Barrett: Trans. AIME 175, 106. Melals Tech., Feb. 1948. TP 2327.

Jan 1, 1950

By J. H. Swisher

The solubility of sulfur and rate of solution of sulfur in pure Lron were measured in H2S + H2 and H2S + H2 H2O gas mixtures. The solubility and diffusivity of sulfur at 1410°Care 0.13 pet S and 1.0 x 10-5 sq cm per sec, respectively. The solubility iS the same, but the rate of sulfurization is slower in the presence of H2O in the reacting gas. Under these conditions, the over-all rate is controlled jointly by a slow surface reaction and by solid-state diffusion; the mechanism for the surface reaction has not been identified. KNOWLEDGE of the behavior of sulfur in solid iron is desirable for the metallurgy of such products as free machining steel, where a high sulfur level is required, and inclusion-free high-strength steels, where the sulfur specifications are very low. The present investigation was undertaken to check previously reported values for sulfur solubility and diffusivity in 6 iron, and to study the poisoning effect of chemisorbed oxygen on sulfurization kinetics in H2-H2S-H2O gas mixtures. All of the experiments were performed at 1410°C. The thermodynamic behavior of sulfur in 6 iron was the subject of a paper by Rosenqvist and Dunicz.' The sulfur solubility at 1400" and 1500°C was determined by equilibrating pure iron specimens with H2-H2S gas mixtures. The maximum solubility of sulfur in 6 iron was alsc determined by Barloga, Bock, and parlee2 by reacting iron wires with sulfur in sealed capsules. In another investigation, the diffusion coefficient of sulfur in 6 iron at temperatures up to 1450°C was measured by Seibel.3 The method used was to measure sulfur concentration profiles in diffusion couples containing radioactive sulfur EXPERIMENTAL Apparatus. A vertical resistance furnace wound with molybdenum wire and containing a recrystallized alumina reaction rube was used for the experiments. The hot zone in the furnace was approximately 2 in. long with a temperature variation of ±3oC. The hot zone temperature was automatically controlled to within ±2°C, and the test temperature was measured with a pt/Pt-10 pet Rh thermocouple before and after each experiment. Flow rates of the reacting gases were obtained using capillary flow meters. Materials. The source of H2S in the gas train was a premixed cylinder containing 5 pet H2S in H2. This mixture then was diluted with additional hydrogen and argon. In some experiments, water vapor was introduced by passing hydrogen and argon through a column containing 10 pet anhydrous oxalic acid and 90 pet oxalic acid dihydrate. The vapor pressure of water above this mixture is well-known.4 Argon was used as a diluent to minimize thermal segregation of H2S in the furnace5 and to reach higher H2O:H2 ratios than could be obtained in mixtures of H2 and H2S alone. Argon was purified by passage over copper chips at 350°C and subsequently over anhydrone. Hydrogen was purified by passage over platinized asbestos at 450°C and then over anhydrone. The H2-H2S mixture was purified by passage over platinized asbestos and then over P2O5. The specimen stock was made by melting and vacuum-carbon deoxidizing electrolytic "Plastiron" in a zirconia crucible. The principal impurities are listed in Table I. In some of the equilibrium experiments, six-pass zone-refined iron was used to minimize impurity side effects. This zone-refined iron had a total impurity level of about 25 ppm. Procedure. Specimens were annealed in hydrogen for a period of at least 2 hr at the beginning of each experiment. The specimens were held in the reacting gas for times varying between 10 min and 17 hr, and cooled to room temperature in a water-cooled stainless-steel block at the bottom of the furnace. The pH2S/pH2 ratios reported are those for gas equilibrium at 1410°C. Calculations based on available thermodynamic data8 showed that the only other gaseous8 species that formed in significant amounts in the furnace were S2 and S. Even when water vapor was introduced into the gas mixture, the concentrations of SO2, SO, and so forth, were negligible. The initial partial pressure of H2S was therefore corrected for its partial dissociation to S2 and S in determining the equi-

Jan 1, 1968

By J. S. Bowles

THE martensite transformation in lithium, dis- covered by Barrett,' has been studied extensively by X-ray techniques by Barrett and Trautz,² and Barrett and Clifton.V he present paper reports the results of an investigation into the metallographic characteristics of lithium martensite. Such an investigation has not been carried out before. The spontaneous transformation in lithium consists of a change from a body-centered cubic to a close-packed hexagonal structure with the hexagonal layers in imperfect stacking sequence." As far as is known at present, this transformation can be regarded as being crystallographically equivalent to the body-centered cubic to close-packed hexagonal transformation that occurs in zirconium,5 although stacking errors have not been reported in zirconium. From a study of the orientation relationships in zirconium, Burgers5 as proposed that the martensite transformation, b.c.c. to c.p.h., occurs by a heterogeneous shear on the system (112) [111]. The crystal-lographic principle underlying this proposal is that the configuration of atoms in the (112) plane of a b.c.c. structure is exactly the same as that in the (1010) plane of a close-packed hexagonal structure based on the same atomic radius. The pattern in 2v2 both these planes is a rectangle d X 2v2d where v3 d is the atomic diameter. Thus a close-packed hexagonal structure can be built up from a body-centered cubic structure by displacing the (112) planes relative to each other.* This mechanism leads to orientations that can be described by the relations: (110)b.c.e. // (0001)c,p.h.; [111]b.c.c. // [1120]c.p.h Observations confirm these relations. In zirconium, Burgers' measurements indicated an angle of 0" to 2" between the close-packed directions, while Barrett's measurements on lithium indicated an angle of 3". According to the Burgers' mechanism, the martensite habit plane for this transformation would be expected to be the (112)b.c.c. plane, for this plane would not be distorted by the transformation. One of the purposes of this investigation was to find out whether the observed lithium habit plane agrees with this prediction of the Burgers' mechanism. Experimental Procedure Materials: The lithium was from the same purified ingot used by Barrett and Trautz.² The Bridgman technique was used to produce single crystals. To maintain a temperature gradient in the melt, during the production of these crystals, it was necessary to use a steel mould with a wall thickness of only 0.015 in. Metallographic Techniques: Lithium specimens could be given an excellent metallographic polish by swabbing them gently with cold methyl or ethyl alcohol.? The best results were obtained with methyl alcohol saturated with the reaction product, lithium alcoholate. With higher alcohols the reaction became progressively slower and the attack became an etch pit attack rather than a polish attack. Butyl and amyl alcohols were used for macroetching. After polishing, it was necessary to remove all traces of alcohol from the specimens; otherwise, on subsequent quenching in liquid nitrogen, the alcohol froze to a glassy film. The alcohol was removed with dry benzene. The benzene in turn had to be removed before quenching, but since it does not react with lithium it could be allowed to evaporate. The specimens could then be quickly quenched before they began to tarnish. This operation could be carried out in air on all but excessively humid days when it was advisable to use an atmosphere of dry nitrogen or argon. For examinations at room temperature, the specimens could be transferred directly from the benzene bath into a bath of mineral oil. In mineral oil the specimens oxidized slowly by the diffusion of oxygen through the oil but the structure remained visible for about an hour. Lithium Martensite: Specimens prepared in the manner described above transformed spontaneously to martensite with an audible click when quenched into liquid nitrogen; i.e., M, was above the boiling point of nitrogen (77°K). The disparity between this result and the M, temperature of 71°K, found by Barrett and Trautz, is probably to be attributed to the large grain size and freedom from mechanical deformation of the specimens used in the present work. The relief effects produced by the transformation did not disappear when specimens were quenched from liquid nitrogen into mineral oil at room temperature. This permitted the microstructures to be studied at room temperature where, of course, the martensitic phase was no longer present. Typical micrographs of lithium "martensite" made at room temperature are reproduced in figs. 1, 2, and 3. As anticipated by Barrett and Trautz, the microstruc-

Jan 1, 1952

By Irving B. Cadoff, Alvin A. Machonis

The resistivity, Hall coefficient, Seebeck coefficient, and thermal conductivity were measured as a function of temperature for cation-rich alloy single crystals covering the composition range across the PbTe-SnTe system. Alloying of PbTe with up to 20 pct SnTe was found to have little effect on the energy gap. Above 20 pct SnTe the alloys were "p" type but below this range the sign could be varied by heat treatment. The lattice thermal resistivity of the compounds SnTe and PbTe is raised by alloying one with the other. Z values in the order the interesting values obtained. THE PbTe-SnTe system has several interesting features. For one, PbTe is a useful thermoelectric material and the possibility of improving its figure of merit by alloying with SnTe, an isomorphous compound, has been suggested since these pseudo-binary solid solutions generally have a more favorable ratio of electrical conductivity to thermal conductivity than either of the components.' Other interesting features relate to the conductivity mechanism, band structure, and stoichiometry of the compounds and their alloys. PbTe is a semiconductor with an energy gap of about 0.29 ev2 at room temperature whose conductivity sign and magnitude can be varied from "n" to "p" by controlling the proportion of lead and tellurium with respect to the stoichiometric ratio.3 Excess lead results in "n"-type conduction. SnTe is found to exist only as a "p"-type material of relatively high conductivity. This behavior is attributed to stoichiometric deviation by Brebrick4 but Sagar and Miller proposed that the behavior of SnTe must be due in part to the presence of an overlapped band. An investigation of alloys of this system, therefore, might give additional information which would permit one to evaluate which of the two proposals is the more appropriate one. Abrikosov et al.' studied the room-temperature electrical properties of these alloys and reported data for Seebeck coefficient and resistivity on poly-crystalline alloys. The present work is a more exhaustive survey of the PbTe-SnTe system. Re- sistivity, Hall coefficient, Seebeck coefficient, and thermal conductivity were measured over a wide temperature range for single crystals at 10-pct intervals of lead/tin ratio across the pseudobinary system. The relative concentration of tellurium was controlled so as to obtain metal-ion excesses in all cases. SAMPLE PREPARATION The crystals were prepared by melting elemental lead, tin, and tellurium in weighed proportions in evacuated Vycor capsules. The lead and tellurium were high-purity grades obtained from American Smelting & Refining Co. The tin was supplied by Comico. The proper calculated proportions of lead, tin, and tellurium were weighed and charged into prepared Vycor capsules prior to evacuation. The capsules were prepared from 15-mm Vycor tubing. A sharp point was worked on one end of the tube. A pyrolytic graphite coating was deposited on the Vycor walls by heating the tip to 800°C in an atmosphere of acetone-saturated argon. An additional coating of graphite was deposited on the pyrolytic coating from an Aquadag suspension. Above the coated tip the tube was reduced in diameter to form a constrictive neck. To avoid scratching the graphite coatings the charge was placed in the tube above the constriction. After a low-temperature bake, the evacuated capsule was sealed. On subsequent heating the charge melted down into the lower portion of the capsule. The crystals were grown by lowering the capsule through a Bridgman-Stockbarger furnace. The lowering rate was 1 in. per 8 hr. The upper portion of the furnace was set for 950°C and the lower portion for 800°C. In general the yield of single crystals was about 25 pct. The mixed compositions were, as expected, the most difficult to grow. The finished crystals were sectioned into 5/8-in. slices. The tip, end, and middle slices from each crystal were analyzed by X-ray fluorescence to determine the lead-to-tin ratio. The resulting values were used to plot a composition vs distance plot for each crystal. Slices were selected from each crystal, with the aid of the composition plots, to cover the complete range of compositions at 10-pct intervals. In general, the slices selected were taken from the seed end of the crystal where the longitudinal segregation (as determined from the X-ray fluorescence analysis) was a minimum. Laue single-crystal analysis and metallographic analysis was used to verify if a slice was single or polycrystal. Any grain boundaries were clearly visible in the as-cut and polished condition. In ad-

Jan 1, 1964

By John Fritz

THE John Fritz Medal was presented to Ambrose Swasey of Cleveland, Ohio, in the Auditorium of the Engineering Societies Building, in New York, on April 23. Charles F. Rand, Chairman of the Board of Award, presided and, after speaking very briefly of Mr. Swasey, whose friend he has been for a great many years, ,introduced Gen. William Crozier, formerly Chief of Ordnance, U. S. Army, who spoke most entertainingly of, Mr. Swasey's accomplishments in designing and manufacturing instruments of precision, particularly for the use of artillery in range finding: Dr. William Wallace Campbell, Director of the Lick Observatory, and President of the University of California, described Mr. Swasey's, contribution to astronomical advancement by his notable development of the largest telescopes in this country.

Jan 1, 1924

By George F. Weaton, Carleton C. Long, H. I. Najarian

Partial descriptions of the operation of the St. Joseph Lead Company's Joseph-town smelter have been published. In, 1936 the electrothermic production of zinc oxide was described;' in 1939 appeared a description2 of the electrothermic method of producing zinc metal. Inasmuch as the plant capacity has more than doubled, and in view of the fact that operating practices have improved greatly since these publications, it seems worth while to prepare a fresh description of the present-day elec-trothermic zinc plant and practice. Josephtown smelter is situated on the south side of the Ohio River about 3 miles below its confluence with the Beaver River. In addition to river barge, the smelter is served by Pennsylvania state highway No. 18 and by a spur line of the Pittsburgh and Lake Erie Railroad (N.Y.C.). A recent extension of this spur line connects with the Pennsylvania Railroad. As originally contemplated the plant was to handle only the product of the com-pany's own mines in St. Lawrence County, New york, but owing to the incessant demand for zinc and zinc oxide, it has been necessary to supplement New York concentrates with foreign ores (principally from Quebcc and the Argentine). The general operational procedure followed comprises roasting the sulphide con-centrates, converting the sulphur dioxide into sulphuric acid, preparation of a strong-structure sinter from the calcine, crushing &lid sizing of coke, reduction of coke-sinter mixture by electrothermic means, condensation of the evolved zinc vapor to make zinc metal or burning of the zinc vapor to make zinc oxide, collection and packing of the zinc oxide. Dusts recovered by the roaster and sinter Cottrells are treated in the leach plant for separation of lead sulphate, cadmium metal and zinc sulphate. The general flowsheet is shown in Fig. I. Principal Items OF Equipment Roaster Plant Concentrate drier, 6-ft. 'ia. by 4O ft. 5 in., countercurrent, direct gas-fired. 3500-~on concentrate storage in three vertical steel tanks. Five modified Nichols-Herreshoff twelve-hearth roasters, 21 ft. 6 in. in diameter. Four fans for shaft-cooling air. One threedrum Stirling water-tube waste-heat boiler, 4'8 hp., 200 1b. Per sq. in., with connections to upper and lower balloon flues. Direct gas-fired countercurrent rotary-kiln roaster for Cottrell dust. Necessary conveying equipment, described below. Instrumentation consists of: draft indicators, (3d hearth); various manometers; pyrometer served by thermocouples in each hearth, entrance and exit of waste-heat Joseph. entrance and exit of each hot Cottrell; roaster draft recorder and shaft air-pressure controller; temperature recorder and controller (10th and 12th hearths); SO* recorder (waste-heat boiler n

Jan 1, 1944

By W. A. Koehler, M. E. Hinkle

INTRODUCTION THE oxidation of pyrites and marcasite in coal-mine strata to produce discolored acid mine drainage has long been explained by chemical reactions occurring in three stages: I. The iron sulphide minerals are oxidized by air in the presence of water to produce a nearly colorless solution of fer¬rous (iron) sulphate and some sulphuric acid. 2. The ferrous sulphate and part of the sulphuric acid combine with additional oxygen to form ferric (iron) sulphate. 3. The ferric sulphate hydrolyzes to form a reddish-brown precipitate and additional sulphuric acid. Nevertheless, chemical data alone are not sufficient to explain all observed facts. The first stage seems to proceed more slowly in the chemical laboratory than in nature. The second and third stages nor¬mally occur to a marked extent within a few days with raw mine water. However, the visible discoloration that characterizes these latter stages will not develop for months if the mine water is sterilized. By means of bacteriological techniques, two organisms have been isolated from acid coal-mine drainage. These are believed to have a part in promoting the chemical reactions summarized above. One organism is considered to be Thio¬bacillus thiooxidans, which is known to be able to convert elementary sulphur or sodium thiosulphate to sulphuric acid. Its relation to the formation of acid mine drainage has not yet been established. Apparently it does not promote the oxida¬tion of ferrous iron compounds in mine, drainage to the ferric state. The second organism has not been identi¬fied by name but is described as "Gram negative, non-spore-forming rods approxi¬mately 0.4 micron wide by o.8 to 1.0 micron long." A pure culture of this when added to sterile mine water will cause the latter to become amber and develop the typical rusty precipitate. However, it has not been found to convert sulphur com¬pounds to sulphuric acid. Further research is planned to determine whether or not these microorganisms play a significant part in the first stage of oxidation whereby pyrites and marcasite minerals go into solution. Some of the conditions found in abandoned sections of coal mines, such as a reduced percentage of oxygen and increased percentage of carbon dioxide in the air, as well as the existing temperature and acidity ranges, will be tolerated by and may even be favorable to these organisms. ACID COAL MINE DRAINAGE Acid coal mine drainage has been the concern of coal mine operators, industrial¬ists, sportsmen and public officials for many years. The amount of acid flowing into our streams in the coal-producing areas varies considerably from mine to mine and from

Jan 1, 1948