Search Documents

By R. A. Bergier

The Transactions of the Institute contain nothing, as yet, on the subject of pocket-compasses; and in the belief that American miners, explorers, geologists, and engineers will gladly welcome any infor mation about new forms of apparatus, simple in construction and adapted to rapid use, I offer a short description of an improved French combination pocket-compass, which, if once introduced into use, would seem likely to supersede similar instrumens of older pattern. The instrument in my possession I owe to the kindness of M. G. de.La Bouglise, of Paris. The frame of the compass is a double-bottomed box, 2 1/2 inches square and 9/16 of an inch high, made of white metal, and with its sur faces very carefully planed. The sides of the box make true right angles with each other. Two sides are parallel with, and two are normal to, the north and south line of the principal graduation. The bottom is accurately planed, so that the instrument will lie true on a plane surface. A glass, 2 3/8 inches in diameter, is set in the top plate. The graduation for the needle is engraved on the upper face of a ring, connected with the flat disk, in which the center-pin is in serted. Between this disk and the bottom of the box there is a hollow space a quarter of an inch deep. The needle is 1 7/8 inches in length, and can be balanced by means of a small sliding piece of metal. The graduation extends from 0° to 360°, reading from right to left. The stopping of the needle is effected by a screw, A, on the side of the box near the handle, H (Fig. 1). There is also a clinometer attachment, the graduation for which is engraved on the upper face of the silver-plated disk. The compass has two sights. The north sight, B, is a simple pin, a little more than an inch high, which, when not in use, is kept folded down, and is partially protected by the exterior sliding-plate, C. When raised for use, the sight is stopped in a vertical position by a projecting pin attached to the side of the box.. The south sight, D, is connected with the handle, H, and the sight and handle

Jan 1, 1890

By R. D. Carnahan, J. E. White

ThE use of strain gages in the measurement of microplastic behavior of materials is well-known.'-3 Recently it has been suggested that similar techniques might be useful for determining stress relaation. It is the purpose of this report to comment on the use of strain gages in the measurement of strains in the vicinity of 10"6. We will also discuss observations of an anomalous anelastic behavior apparently associated with small temperature changes, which accompanies the unload portion of a load-unload microstrain test. The key to successful strain determinations at levels below 1 pin. per in. is a good gage-mounting technique and either precise ambient temperature control or a set of matched temperature-compensated gages. The importance of good mounting cannot be overemphasized, for example, as in the use of Eastman 910 contact cement. If the cement layer is not sufficiently thin and properly hardened, it is possible to observe anomalous negative stresses when small loads are removed, which relax back to zero in an orderly way with time. Such anomalous behavior, thought to be due to gage bonding, has been reported in microstrain experiments by Thomas and verbach' who observed a negative strain of -3 X lo-' upon unloading. This kind of behavior severely limits the over-all strain sensitivity which can be achieved in such tests. The relaxation of a small positive strain subsequent to unloading in a load-unload experiment is quite normal, however, and is to be expected. The occurrence of an apparent negative strain is also encountered in those instances where the elasticity of the bonding cement is exceeded—for example 0.5 pct or 5000 pin. for cured Eastman 910. An elastic strain of this magnitude can be encountered during load-unload type testing particularly in higher-strength materials (-150,000 yield strength). During the course of microplasticity studies on pure nickel and nickel alloys,' the authors have made the following observation. In a four-point bending test, two active gages are mounted one on each side of the beam as arms R1 and R z of a conventional strain-gage bridge circuit shown in Fig. l(a). This technique provides two advantages: the sensitivity is doubled because R1 and Rz experience opposite strains and temperature compensation is provided automatically because any ambient temperature change would cause both gages to see a strain of like sign whose signals would cancel in the circuit.

Jan 1, 1964

By Robert D. Thomson

LISTED among strategic and critical minerals for stockpiling, mica is an important raw material in electronic and electrical equipment industries. Each year large quantities are consumed in the manufacture of television and radio tubes, radar sets, generators, transformers, electric toasters, and irons. Crude mica, which comes from the mine in crystals or in rough books of various shapes and sizes, is known as run-of-mine or book mica. Structural imperfections, impurities, rough edges, and defective laminae are removed by cobbing, rifting, and trimming to produce a marketable block mica or film mica.' After the rough books have been hand-cobbed to remove adhering rock, dirt, and crushed or defective mica they are rifted, or split. In the U.S. a straight-bladed knife is generally used for rifting. Products of this operation are classed broadly as untrimmed sheet mica and scrap. Sheet mica is any relatively flat piece sufficiently free from physical defects to be cut or stamped into specified shapes for industrial use. Sheet mica is classed as block, film, and splittings. Block mica is not less than 0.007 in. thick with a minimum usable area of 1 sq in. Film mica is split from the better qualities of block mica to groups of specified thickness ranging from 0.0012 to 0.004 in. Splittings are sheets with maximum thickness of 0.0012 in. and minimum usable area of 3/4 sq in. As virtually no mica splittings are produced in the U.S., they will not be discussed in this report. Small, low quality block is subdivided as punch and washer. Punch mica is thumb-trimmed material large enough to yield a circular disk of at least 11/2 in. diam for stained quality mica and 1 1/4 to 2 in. for clear quality. Poorer lots, often referred to as washer mica, are also included in the general term punch mica. Trimming, the next step in processing sheet mica, removes broken and ragged edges, loose scales, and other major imperfections. Trimming may be done with a knife, sickle, shears, or fingers. In the U.S. it is usually done with a 3-in. linoleum knife to obtain a bevel-edged cut. If ragged edges are broken off with the thumb and fingers, the mica is called thumb-trimmed. Full-trimmed is rifted mica trimmed on all sides with all cracks, reeves, and

Jan 1, 1957

By E. O. Bennett

When oil is takcn from a subsurface structure it is generally accompanied by gas. The gas thus produced represents the 1ighter hydrocarbons present in the original petroleurn accurnulation, which arc, insoluble at the reduced pressures created around a well when it is producing. In some cases the gas accompanying the oil may come from a gas-bearing stratum not in immediate contact with the oil. The amount of gas from the formation accompanying each barrel of oil is called the natural gas factor. Energy Causing Well to Flow The force causing the flow of fluid into a well when it is drilled into an oil-bearing structure is the pressure differential between the well bore and the formation. A pressure differential between the formation and the well may be set up in three different ways, as follows: (1) pressure due to gas in solution or in contact with the oil, (2) hydrostatic pressure due to water in contact with the oil (it may be either bottom or edge water); (3) pressure difference due to forcc of gravity. The greatest source of energy for producing oil from most oil fields, and the one over which the greatest control can be exerted, is the poten-tial energy in the gas under pressure in the formation. In any pool there is but a definite amount of gas available. Part of this gas may be in solution and a part in contact with oil. The amount of gas in solution in each bard of oil depends on the pressure and temperature in the formation and the characteristics of the oil. Whether the gas is in solution or in contact with the oil it is necessary to use the energy it, contains as efficiently as possible in order to obtain the greatest ultimate recovery from the pool. Bush1 states: Gas being the most efficient aid in moving the oil, it is important to prevent more of it from escaping than is necessary to remove the maximum amount of oil from the sands. The conservation of this energy is far more important to the producer of oil than his returns from sales of gas to distributing companies. The flowing life of the well is the most profitable period, and keeping the gas-oil ratio low, or keeping the

Jan 1, 1928

By D. R. Snow

The year 1930 stands out in the petroleum industry as an exceptional one in many ways. It is one of the few years in its history during which crude oil production declined from that of the previous year in nearly every important producing district in the United States and in the world as a whole. World production of crude oil declined approximately 81,000,000 bbl., from 1,484,451,000 bbl. in 1929 to 1,403,500,000 bbl. in 1930. Production of crude oil in the United States declined approximately 111,000,000 bbl., from 1,007,323,000 bbl. in 1929 to a production of 896,265,000 bbl. in 1930. World production outside of the United States increased approximately 30,000,000 bbl., due principally to the increased production in Russia. This, together with the decided decrease of production in the United States, resulted in a smaller percentage of world production in the United States than in any other year since 1921. This declining production occurred in the face of the greatest visible supply in the form of potential production that the industry has ever known and was clearly the result of the great efforts put forward to restrict production, both by proration and by unitization. Throughout the year, developments along the lines of proration and unitization have overshadowed all other developments in the minds of those interested in the oil industry and will, no doubt, continue to do so more and more in the future, as it is quite evident that the industry cannot hope to maintain itself in a profitable position, without some rational plan of bringing about a better balance between supply and demand than has existed in the past. The successful operation of the Van field unitization agreement and the recently completed Kettleman Hills plan are indicative of what mag be expected in the future along this line. That real progress has been made in this direction is shown by the fact that total crude oil stocks in the United States were decreased by approximately 28,000,000 bbl. during the year 1930. This is the only year on record during which such a decrease of crude oil stocks was accompanied by a severely declining price structure. This reduction of crude stocks is apparently continuing even after the price has reached its present low level, indicating that there is no

Jan 1, 1931

By J. T. Norton, A. L. Mowry

S. J. SINDEBAND*—(1) Discussing the properties of the powders used, Mr. Rostoker mentioned a silicon powder as being between 150 and 325 mesh. We always had much difficulty in measuring particle size of silicon powder by screen analysis, because of its tendency to agglomerate. I would be interested in the method used to measure these particle sizes. (2) Mr. Rostoker maintains that the measurement of magnetic properties is more accurate in determining complete homogenization of an alloy, than is the X ray diffraction technique. I wonder whether this is really true. Even when diffusion is complete, magnetic properties will change during continuation of the heat treatment, due to change in density and pore shapes, as has been demonstrated by Mr. Rostoker himself. Which effect is faster, the diffusion of the alloy components or the attainment of final density, will, in my opinion, depend very much on initial material and sintering conditions used. For magnetic applications, of course, the magnetic measurements are most suited for determining the point at which equilibrium conditions are reached. (3) I was glad to see that Mr. Rostoker had used sample sizes which are similar to those I had used previously, and I believe that ring samples of about 2 in. od will become more or less standard samples for the determination of magnetic properties of powder metallurgy products. I should like to ask how the density was changed for the samples on which the effect of porosity was investi- gated, and, further, why the sintering temperature used for this series of experiments was so low. It is somewhat surprising that a 24-hr treatment at 850°C acts so much more to spheroidize the pores than a treatment for 1 hr at 1100°C. But the effect seems to be indisputable. I have made an investigation of the influence of sintering temperature for longer times on the maximum permeabilities of iron powder compacts which was presented at the International Powder Metallurgy Conference in Graz, in 1948, and I hope that these results will be published here within a short time. The results of this investigation are confirmed by Mr. Rostoker's findings that the change of time from 1 to 24 hr changes the permeability behavior considerably in the direction as indicated by Polder and Van Santen for spheroidiza-tion of pores. I do not quite understand Mr. Rostoker's explanation of the influ-

Jan 1, 1950

By S. F. Reiter, R. W. Guard, J. H. Keeler

DURING the last several years the authors have been conducting tests on a tensile machine that autographically records load-elongation data. In certain tests at elevated temperatures on face-centered cubic, hexagonal close-packed, and body-centered cubic materials (binary alloys of nickel, zirconium, and iron), the load-elongation curve as shown in Fig. 1 reaches a maximum load (Pmax,) at relatively small amounts of strain and a large amount of elongation occurs subsequently with a continuously decreasing load, until finally localized necking and fracture take place. This early maximum load behavior has been found without the accompanying evidence of localized necking as has been assumed by some, or of evidence of cracking as observed by others.' This behavior has also been observed by Nadai and Manjoinez whose results are in good agreement with ours. The prior strain, strain rate, test temperature, and crystal structure affect the observations. The influence of prior strain was observed in tests on unalloyed zirconium at 300°C in which specimens containing large amounts of prior strain (cold work) exhibited the type of curve shown in Fig. 1. No localized necking was observed after strain as much as that of point B. Annealed and recrystallized specimens of the same material showed a load-elongation curve with maximum load occurring after considerable strain hardening and at the beginning of localized necking. Interrupted tests (Fig. 2) show no loss in strength because of recovery or recrys-tallization during an interval at temperature without load. Recovery under stress such as found by Wood and Suiter3 in aluminum is now being investigated as one possible explanation. The strain rate is a contributing variable as shown in Fig. 3, a test on high purity nickel. Here the strain rate was decreased by a factor of ten during a test in which the maximum load was reached at a small strain. The slope of the true stress-true strain curve was positive with the more rapid strain rate and negative with the slower strain rate. In many binary ferrites an added effect of temperature has been observed. Fig. 4 shows the load-elongation plots for a binary ferritic alloy containing 2 pct Mo. The slope of the small portion of the stress-strain curve obtained at a strain rate of 0.01 mhr1 changes sign from negative to positive on going

Jan 1, 1955

By M. Albertson

At Cobalt, Ontario, Canada, a lake was drained to facilitate mining, by the Mining Corpn. of Canada, during the spring and early summer of 1915. Previous to pumping out the water, great quantities of sands and slimes from concentrating plants had been discharged into the lake and during and after the lake's drainage, its basin was a receptacle for tailing products. As the writer was at work along the shore line as the lake was being drained, he had a good opportunity to observe the changes that took place as the water was withdrawn. Some adjustments between the incoming sands and the mud in the lake had taken place before pumping was commenced. One of the most interesting results was the appearance of a small dome in a path the writer traversed twice a day for several months; he remembers distinctly the difficulty of crossing this. Cobalt Lake owed its existence to the gouging out of a rock basin by glaciation. The long axis of the basin closely follows the strike of a thrust fault of about 500 ft. (160 m.) vertical displacement. The lake was originally shaped somewhat as shown. The length was about 3000 ft. (914.4 m.), the width at the lower lobe was about 1000 ft., and the width at the narrows probably 400 to 500 ft. The original depth of water varied from 20 to 30 ft. (6.1 to 9.1 m.), near where the island later was formed, to 60 to 70 ft. (23.6 to 27.6 m.) in the widest part of the lower lobe. At the narrows, the depth was 30 to 40 ft. Above the bed rock was sand, with boulders near the bottom, and mud. During the building of the railroad in 1903, considerable filling was done along the right of way. With the commencement of mining operations, about 1905, waste rock and mill tailings were dumped into the lake. One of the mining companies operated a hydraulic giant to remove the glacial debris from several hundred acres of rock surface; much of the sand and clay from this operation was deposited in the lake. About 1,500,000 tons of mill tailings, composed of sands and slimes, were discharged into the lake's waters previous to 1915. Most of this material

Jan 1, 1921

NAME AND OBJECT. SEC. 1. This Institute is incorporated under the Membership Corporation Law of the State of New York ; its corporate name is AMERICAN INSTITUTE OF MINING ENGINEERS; and its objects are such as are stated in its Certificate of Incorporation. ARTICLE II. MEMBERS. SEC. 1. The membership of the Institute shall comprise four classes, namely (1) Members ; (2) Honorary Members , (3) Associates , and (4) Honorary Associates Only Members and Associates residing within the United States of America, Republic of Mexico and Dominion of Canada shall be entitled to vote at the meetings of the Institute. SEC. 2 All Members, Honorary Members, Associates and Honorary Associates of the American Institute of Mining Engineers as the same existed on the day of the incorporation of this Institute, are Members, Honorary Members, Associates and Honorary Associates, respectively, of this Corporation SEC. 3. The following classes of persons shall be eligible for membership in the Institute, namely, as Members and Honorary Members, all professional mining engineers, geologists, metallurgists or chemists, and all persons practically engaged in mining, metallurgy or metallurgical engineering ; as Associates and Honorary Associates, all persons desirous of being connected with the Institute who, in the opinion of the Council, are suitable. SEC 4. Every candidate for election as a Member or Associate of the Institute must be proposed for election by at least three Members or Associates; must be approved by the Committee on Membership, as prescribed in the By-Laws ; and .must be elected by the Council. Not less than three-fourths of the votes cast shall be necessary to an election Every person so elected shall become a Member or Associate, as the case may be, upon payment of his first dues as herein-after prescribed Each candidate for Honorary Member or Honorary Associate, must be recommended by at least ten Members or Associates ; must be approved by the Council ; and must be elected by ballot at a meeting of the Board of Directors by the unanimous vote of all the Directors present ; provided, however, that the number of Honorary Members and Honorary Associates shall not at any time exceed twenty SEC. 5. If any person elected a Member or Associate does not, within sixty days after notice of his election, accept the same and pay his initiation fee and dues for the current year, his election may be cancelled at the discretion of the Council.

Jan 1, 1910

By Mark J. Klein

An internal-friction profile induced by nitrogen in Cr-35 at. pet Re was studied as a function of nitrogen concentration and heat treatment. From these studies, the solubility of nitrogen in this alloy was deduced. The equilibrium solubility of nitrogen in chromium does not appear to be substantially changed by the addition of 35 at. pet Re to chromium. However the precipitation kinetics of nitrogen from solution are significantly decreased. IT has been found that rhenium has a beneficial effect on the low-temperature ductility of Group VI-A metals. As part of a study to investigate the mechanism of this increased ductility, it was of interest to compare the concentration of interstitials retained in solution in one of these ductile bee alloys with the concentration retained in solution in its base metal. In this regard, a study of the solubility of nitrogen in ductile Cr-35 at. pet Re was selected for this phase of the investigation because the solubility of nitrogen in the base metal, chromium, has been determined over a fairly large temperature span.1-3 In addition, nitrogen is known to have an embrittling effect on chromium,4 but does not appear to have a comparable embrittling effect on Cr-35 at. pet Re.5 The experimental method selected for this study was the measurement of internal friction. This technique allows interstitial-concentration measurements to be made in bee metals that are sensitive to small changes in the concentration of a particular interstitial, even when other interstitials are present. When subjected to a cyclic stress, interstitial atoms in solid solution give rise to an internal-friction peak whose origin is the stress-induced ordering of interstitials into preferred lat- tice sites. These internal-friction peaks signify a dissipation of elastic energy which is greatest when the period of oscillation is comparable with the relaxation time for the attainment of an equilibrium interstitial distribution. For dilute interstitial binary alloys, the height of the internal-friction peak is proportional to the concentration of interstitial atoms in solid solutions. snoek8 has shown that the internal friction, Q-1, may be expressed by the equation where A is the relaxation strength, ? is the angular frequency, and 7 is the relaxation time. The relaxation strength, A, is proportional to the concentration of interstitials taking part in the relaxation if no interaction occurs between solute atoms. Thus values of peak height, which can be determined as a function of temperature, give a measure of the relative concentration of interstitial atoms in solution at various temperatures. If equilibrium has been attained, the peak heights will be proportional to the interstitial solubilities. The constant that relates A to the interstitial concentration can be determined experimentally from peak-height measurements as a function of concentration for specimens of constant crystallographic orientation. When this has been done, Q-1 measurements can be used to determine solubilities according to the equation C - KQ-1 where C is the soluble interstitial concentration and K is a constant that can be experimentally determined. It is possible, however, that lattice imperfections may bind interstitials to certain lattice sites. Internal friction does not measure these interstitial~, but does measure interstitials which are free to move in the normal lattice sites when subjected to an applied oscillating stress. On alloying the pure metal with a substitutional

Jan 1, 1965

By J. J. Arps

n approach to the study of the electrical properlies of drilling muds, their cakes and their filtrates was made by treating the drilling fluid as a porous medium. Lluring this study it was found that the weight pararneter was omitted from previous investigations on electrical properties. Patnode in 1949 made a similar approach to ,his investigation. His work showed that there was a variation of resistivity relationships with per cent Puid present in a given suspension. This present study ex-tends Patnode's investigation to one in terms of the solids fraction of the drilling fluids. Previous investigations were made on low weight muds where the effect of the rolids fraction was obscured. The following equationr were fitted to data taken from 94 field muds and 47 laboratory muds (see Tables I and 2). The parameter, C, is a complex function of the solidr content, or mud weight, of a drilling fluid. It was also found that for all drilling muds examined. A nomograph is presented combining Eqs. I and 2. INTRODUCTION It is generally recognized that the materials present in drilling muds affect the relationship between mud filtrate and mud resistivities. However, most electric log interpretations proceed with the assumption that the mud resistivity and temperature are the only important parameters needed to obtain a filtrate resistivity or a mud cake resistivity. Lamont1 suggests that only average relationships exist between mud cake, mud filtrate and mud resistivities. He indicates that there is limited accuracy when these intercorrelated factors are used since no other measure-able variable is apparent. A previous paper by Patnode indicates that drilling fluids may be considered to be a system of fluids in solid particles which may be correlated electrically in a manner similar to rock solids. 1 he equation for the resistivity factor. F = (per cent fluid) is satisfied for a given clay type in water, but the value of m varies as different materials are used in the water. The resistivity factor is not constant for a given amount of clay. As is suspected it varies as the solids fraction conducts electrical current. Since both weighting material and clay solids are present in commonly used drilling fluids, it is expected that both materials contribute to the variation of the m factor in Eq. 3. An extension of Patnode's work is presented in this paper to show some of the interrelations which exist between the resistivities of mud cake, mud filtrate and mud. Use of these data enable a more accurate calculation of mud filtrate and mud cake resistivities if only the mud resistivity and weight are measured. EXPERIMENTAL The measurements of mud weight, fluid and solids resistivity, alkalinity, and chloride content of mud samples were made in this research. Mud samples representing drilling fluids from 94 Louisiana and Texas wells (Table 1) and 47 laboratory-constructed systems (Table 2) were used in the experimentation. The measurements of the mud properties were made both in the field and in the laboratory. The tests on the properties of weight, alkalinity and chloride ion were standard tests as described by API specifications. The resistivity measuring devices were constructed in the laboratory for this study. For details on the resistivity equipment see Fig. 1. The fluid cell

By A. L. Barnes, A. M. Rowe

A heat transfer study was made of hot gas injection into oil shale through wells interconnected by vertical fractures. This analysis involved the simultaneous numerical solution of a nonlinear, second-order partial differential equation that describes two-dimensional conduction heat transfer in oil shale and a nonlinear first-order partial differential equation that describes convection heat transfer in the fractures. Three nonlinear, temperature-dependent coefficients were used in this work; they are thermal conductivity, thermal capacity and retorting endothermic heat losses of oil shale. Vertical fractures were considered to be of finite height. Although vertical conduction heat transfer was not considered, an estimate of the error resulting from this limitation was made. The effects of injected gas temperature, injection rate, system geometry, cyclic injection and time upon retorting efficiency were investigated. Results from this study show that the rate of retorting oil shale is a direct function of both injection temperature and rate, and the theoretical producing air-oil ratio:(AOR) is an inverse function of temperature. Retorting rates are constant until "breakthrough" of the 700 F isotherm at the producing well, assuming constant injection parameters. Retorting rates for bounded systems are higher than the analogous unbounded systems and likewise AOR's are less. The use of an alternating injection-soak routine with high injection rates is less efficient than continuous injection at lower rates. These results indicate that injection temperatures on the order of 2000F or greater may give theoretical AOR's in the economic range. INTRODUCTION Over half of the known oil shale reserves are located in the U.S., and most of them lie in the Piceance Creek basin of Western Colorado. The Colorado oil shale outcrops on the edges of the Piceance Creek Basin. At the outcrops the shale beds are relatively thin, from 25 to 50 ft thick. In the center of the basin the oil shale is as great as 2,000 ft thick and is covered with 1,000 ft of overburden. It has been estimated that there are over 1,000 billion bbl of oil in shales having an oil content over 15 gal/ton in this basin. Oil shale does not contain free oil but an organic matter called kerogen. Kerogen yields petroleum hydrocarbons by destructive distillation. It must be heated to approximately 700F, at which temperature it decomposes into shale oil, gases and coke. The U.S. Bureau of Mines and, more recently, oil companies have conducted considerable research on surface retorting methods to economically recover oil from this shale. Another approach to exploit the oil shale deposits, in particular that portion having 1,000 ft of overburden, is to retort the oil shale in place and produce the liquid and gaseous hydrocarbons through wells drilled into the shale. Some research has been done on this approach.l,2 There are several variations to the in situ retorting approach. These variations fall into one of two groups, depending upon the geometry of the system: (1) retorting in a highly fractured or broken up matrix; (2) retorting from single fractures between production and injection wells. The latter is the group studied. Several investigators,3-6 using various assumptions, have studied flow of heat through horizontal systems. The objective of this work was to make a heat transfer study of in situ retorting oil shale by hot gas injection through wells interconnected by single vertical fractures of finite height. The oil shale thermal conductivity, thermal capacity and retorting endothermic heat losses were considered to be functions of temperature. A knowledge of the

Jan 1, 1969

By L. S. Darken

A quadratic formalism is developed lor the representation of the excess free energy, and of the activity coefficients of each component of a ternary system in the vicinity of a single component selected as solvent. This formalism, in contrast to the e formalism, is thermodynamically consistent at .finite concentrations. Numerous specific systems are used as illustrations, with cross checks where possible; these systems are Fe-C-X systems in the vicinity of 1600°C and include practically all those for which reliable data are available. It is shown that this formalism is usually quite adequate to rebresent available data up to a solute concentration of 20 to 30 at. pet. It is hoped that the formalism here presented may prove useful for the treatment and tabulation of data on ternary and multi-component solutions. SINCE, as discussed in a prior paper,' we do not as yet have an adequate basic understanding of the nature of binary metallic solutions, we cannot hope to be in better position for ternary and multicomponent systems. However, the accumulation of thermodynamic data on ternary and multicomponent metallic solutions has led to an urgent need for a rational formalism for the presentation and use of such data. Notable attempts to represent the isothermal isobaric thermodynamics of ternary solutions were made by Benedict et 01.' and by Wohl.3 These attempts were directed toward developing an analytic expression adequate to encompass the entire ternary triangle, primarily for organic systems; they generally involve the power-series approach, which has been shown' to be inappropriate, in general, even for binary metallic systems. On the other hand, interest in the thermodynamics of ternary and multicomponent metallic solutions has tended to focus either on general thermodynamic relations4-10 over wide compositional ranges, or on cases where one or more components have been at rather low concentration. This latter approach has been followed by Wagner,= by chipman,11 and by Alcock and Richardson,12 and more recently in many publications by the same and other authors. It has already been shown' that the thermodynamic behavior of binary metallic systems is, in general, relatively simple only in the terminal regions. Hence, it would appear that any approach, at this time, to a simple formalism for ternary and multicomponent systems must, a fortiori, be limited to the vicinity of the major component or solvent. The present treatment is aimed to be useful for a given solvent with moderate solute concentrations ranging up to 20 or 25 at. pet and in exceptional cases to considerably higher concentrations. In order to achieve even this modest objective, it is necessary that any appropriate formalism have built into it 1) a thermodynamic consistency (at least within the desired degree of approximation), and 2) an approach at infinite dilution to Raoult's law for the solvent and to Henry's law for each solute. Let us first formulate the condition of thermodynamic consistency for a ternary system. Under isothermal isobaric conditions, we may write for the molal value G of any extensive function dG - C1 dN1 + G2 dN2 + G3 dN3 [l] where the G's are the corresponding partial molal quantities and the N's are the atom fractions. Taking component 1 as the solvent, this relation may be rewritten in terms of the independent variables N2 and N3

Jan 1, 1968

By Arnulf Muan, Carlos Landolt

Equilibria involving Cu-Pt alloys, copper oxides, and atmospheres of known ox2gen pressures have been determined at 1000' and 1200 C. The data obtained have been used to calculate activity-composition relations in the alloys. A moderate negative deviation from ideality is found. At high copper concentrations, the results of the present study are in good agreement with those of previous investigators, whereas at low copper concentrations the activities obtained in this investigation are slightly higher than those reported previously. The present study is part of a research program dealing with the determination of phase relations and thermodynamic properties of copper-containing systems at high temperatures. The information available for such systems is very scanty, particularly for copper oxides and their combinations with other oxide components. Platinum is commonly used as a container in studies of oxide equilibria. To evaluate quantitatively the extent of reaction between the oxide and the container, a knowledge of activity-composition relations in Cu-Pt alloys is necessary. Such data are not available for Cu-Pt alloys in the temperature range of particular interest in the present research program, and particularly for alloys low in copper. Studies of various aspects of the systems Cu-Pt and Cu-0 have been reported in previous literature. The system Cu-Pt is known1 to form a continuous solid-solution series above 812.C, whereas ordered phases are present in certain composition ranges at lower temperatures. Thermodynamic data for the system have been reviewed by Hultgren et al.,' who presented free energies of mixing at 65Oo C, mainly derived from electromotive force cell measurements by Weibke and Matthes.3 Enthalpies of mixing at 640°C have been obtained by Oriani and Murphy4 with liquid tin calorime-try. Their results differ considerably from those derived from the temperature dependence of the data of Weibke and Matthes. Thermodynamic data for the disordered alloys have been obtained by Assayag,5 and more recently by Schmahl and Minzl,6 by Myles and Darby,7 and by McCormack, Myers, and Saxer.8 The two latter sets of data7'' became available after the present study was completed. In the system Cu-0+ two oxides are stable at high temperatures, CuO and CuzO+ each having only minor deviations from stoichiometry. Equilibria in the liquidus temperature region of the system Cu2O-CuO have been studied by Roberts and systemsmyth,9'10CuzO-CuO by Vogel and ocher,I1 by Osterwald,12 and recently the the present authors.13 The system is of the eutectic type with a eutectic temperature of 1083.C The composition of the eutectic liquid corresponds to Xcu0 = °.44, and the oxygen pressure of the coexisting gas phase is Po2 = 0.55 atm.13 Equilibrium oxygen pressures for coexistence of solid CuO and solid Cu2O have been determined by Schmahl and Muller,l4 by Gadalla, Ford, and white,l5 by Bidwell,16 and recently by the present authors.13 There is reasonably good agreement among the various sets of data. Free energies of formation of Cu2O(s) from the elements have been derived by Tretyakov,17 by Bidwell,16 by Kiukkola and wagner,18 by Pal'guev and Neuimin," and by Steele and Alcock,20 There is particularly good agreement among the latter three1'-20 sets of data. THEORETICAL BASIS Consider a subsolidus isothermal section of the system Cu-Pt-0, as shown in Fig. 1. Two phase as-

Jan 1, 1970

By T. E. Scott, R. P. Zerwekh

The charactevistics of the deformatiotz of fcc thorium were examined between 78 and 473 K. Activation energy, actiuation volume, and the temperature dependence of the flow stress were determined and conlpared uith several theories for the rate-controlling mechnnistn of the tempemture-dependent component of the flou~ stress. It was established that the Cottrell-Stokes law does not hold, even approximately, for thorium. Through consideration of the above factors and other parameters, it was concluded that the vandom solute barrier theory proposed by Friedel demonstrates the best agreement with experimental observations of the deformation of thorium below ambient temperature. THORIUM, the first metal in the actinide series of rare-earth elements, is interesting and important from two points of view. In the more practical vein, it is a potential reactor fuel. As such, it is important to know its properties. Of specific interest here are the mechanical properties of thorium. Second, no detailed information concerning the deformation characteristics of the actinide elements has been gathered to date. In view of the interesting physical and chemical properties of these metals, their mechanical behavior might reveal characteristics which could improve our understanding of the mechanisms controlling deformation of the more common metals. For example, it has been shown1 that thorium exhibits a yield point which is greatly enhanced by interstitial solute elements such as carbon. This is not a normal occurrence in fcc metals. The goal of this investigation, therefore, was to characterize the deformation of polycrystalline thorium. MATERIAL AND PROCEDURES Thorium, made by the magnesium intermediate alloy process described by Peterson et al.,2 was rolled and swaged to 0.065-in.-diam wire. The metal analysis is given in Table I. After preparation, the oxygen and nitrogen contents had risen to 308 and 60 ppm, respectively. The 0.065-in.-diam wires were cut into 2-in. lengths and annealed in a vacuum of lo-' Torr at 750°C for 1 hr, producing a grain size of 2735 grains per sq mm. The ends of the 2-in. sections were masked off so that a 1-in. gage length could be electropolished. Specimens were polished at 35 v in a solution of 6 pct perchloric acid in methanol which was maintained at 0°C . The gage diameters after polishing were about 0.0625 in. The tests were run on a screw-driven tensile machine at a constant crosshead speed corresponding to a strain rate of 0.005 min-'. The strain rate was changed rapidly after each 0.01-in. extension between 0.005 min-' and one of three higher strain rates which were selected in order to achieve strain-rate ratios of 5, 10, and 20. Tests were run at several temperatures from 78" to 473°K; most were tested at 423", 300°, 215", and 78°K. EXPERIMENTAL RESULTS Flow Stress vs Strain and Temperature. Typical true stress-true strain curves for thorium are shown in Fig. 1 for several temperatures over the range 473" to 78°K. The curves for 78", 215", 300") and 423°K were obtained from strain-rate change tests using the lower (0.005 min-') or base strain-rate values of stress. Additional tests, using the same base strain rate at different strain-rate ratios, gave curves which virtually superposed on those shown, indicating that strain-rate changes did not materially influence the work-hardening characteristics at the base strain rate. The curves for 273") 373") and 473°K were standard tensile tests at 0.005 min-'. The behavior of the flow stress with temperature is

Jan 1, 1968

By R. T. Torgerson, W. A. Baginski

Alloying studies were conducted on modifications of Cb-10W-1OHf (C-129) alloy as part of a cooperative alloy development effort between The Boeing Co. and the Wah Chang Corp. The purpose of these studies was to develop a fabricable, high- strength columbium alloy with superior melding properties. The initial investigations of alloy modifications were conducted using laboratory-melted button ingots. An alloy with the composition exhibited excellent veld ductility, elevated-ternpevature strength, and fabricability. The yttrium-modified alloy was desigrzated C-129Y and was selected for further developrnetzt. Three prodziction heats of C-129Y weve processed into sheet. Welding, forming, and tensile proper-lies are presented for this material. Tungsten-are welds of. C-129Y exhibited a minimum bend radius of 1/2T in the as-welded conditioti compared to 8T for C-129 alloy. An investigation was conducted on Disil coating of C-129Y and test data are presented on oxidation resistance and effects of re-entry environments. The excellent combination of strength, fabricability, weldability, and low transition temperature of C-129Y alloy offers potential design advantages for use of this alloy in structures of aerospace vehicles. It is atiticipated that C-129Y will rapidly supplant C-129 and similar alloys clue to the versatility provided by its impvoved welditzg properties. COLUMBIUM alloys with improved properties are required to achieve better performance and efficiency of radiation-cooled structures for re-entry vehicles and recoverable launch systems. Cooperative work by The Boeing Co. and the Wah Chang Corp. resulted in the development several years ago of C-129 alloy, a high-strength Cb-W-Hf alloy.' This alloy has received favorable consideration for many advanced designs of high-temperature structures due to its excellent combination of properties. However, this alloy exhibits low weld ductility unless given a high-temperature stress-relief treatment. For this reason the development effort was directed towards modification of the C-129 alloy composition (Cb-1OW-1OHf) to eliminate the need for post-weld heat treatment. This paper describes the successful development of an alloy meeting this requirement. This new alloy was designated C-129Y and has a nominal composition of EXPERIMENTAL PROCEDURES Alloying Studies. Various Cb-W-Hf compositions were investigated using are-melted button ingots. These buttons were hot-forged using a protective glass coating and rolled into sheet specimens. Metal-lographic examination: tensile testing, and welding studies were conducted to evaluate properties of the experimental alloys. Sheet Fabrication. Three pilot production heats of C-129Y were fabricated into sheet to establish processing techniques and to determine sheet properties. The three heats consisted of 6-in.-diam ingots weighing from 140 to 250 lb. The ingots were prepared by electron-be am melting followed by vacuum-arc melting. The hafnium and yttrium additions were made during the are-melting operation by tack welding alloy strip additions to the Cb-W master-alloy electrode. The final ingots were machined into billets with samples of the machine turnings collected for chemical analysis. Ingot breakdown methods for the three heats are as follows: Ingot Ingot Heat Size Weiaht___Breakdown Method A 6 in. 250 lb Hot extrusion B 6 in. 140 lb Hot forging C 6 in. 250 lb Hot extrusion Sheet bars from the extrusion and forging operations were conditioned, recrystallized, and rolled into sheet. Initial rolling was conducted at elevated temperatures and final rolling was conducted at room temperature.

Jan 1, 1967

By K. G. Davis

Dilute alloys of silzer in tilz haz been solidzjzed a1 controlled rules, in lzorizontal tubes 2 mrz and 0.5 rn in diam. Radioactive; tracer techniques we?-e used to study solute distvihutions along llze specimens and irmpurity substructures, as functions of the conditions growth. The results have heen mzalyzed using Burton, Prim, and Slichter's tnodel for the solute disty-ihution in the liquid ahead of an advancing solid-liquid interface. DECANTING techniques have been used to establish criteria for the formation of impurity substructure during solidification in several alloy systems An analysis equating the appearance of impurity substructure with the incidence of constitutional supercooling was developed,= in which diffusion was assumed to be the predominant mode of solute mixing in the liquid. Substitution of experimental data into the equations derived from the diffusion analysis gave reasonable values for solute diffusivity in the liquid. However, in these investigations solidification rates of 10 cm per hr and over were used, to minimize the effect of natural conection, whereas for crystals of high perfection lower solidification rates are needed, usually between 1 and 5 cm per hr. A knowledge of the conditions under which impurity substructures will be formed at low growth rates, and the degree of segregation to be expected, is therefore of interest. In the present investigation, radioactive-tracer techniques have been used to study the effect of growth rate, initial solute concentration, and size of specimen on the formation of substructure in uni- directionally solidified rods of dilute silver in tin alloys, over a range of growth rate between 0.5 and 10 cm per hr. Criteria for the formation of substructure were established by auto radiography. This was believed preferable to the decanting technique, for the relationship of the structure on a decanted interface with that of the freezing interface is not clear, since a layer of liquid is left on the surface following decanting.' The effect of substructure on the distribution of solute along the rods was also investigated. EXPERIMENTAL The procedure for sample preparation has been described in detail by einber. Alloys were prepared from tin of 99.999 pct purity and silver of 99.99 pct purity. A"', an emitter of both y and 0 radiation, was used as tracer. Samples of the alloys were drawn up into silica tubes with inside diameters 0.5 or 2 mm, remelted in a horizontal furnace, and solidified at controlled rates. A few centimeters of the samples were left unmelted for a measure of the initial concentration. Total sample length was approximately 20 cm. The temperature gradient in the furnace was kept constant at 36°C per cm in the region corresponding to the melting point for tin. To find how well this corresponded to the actual temperature gradient in the melt, a thermocouple of 38-gage wire was electrically insulated with a thin layer of Sauereisen cement and placed within one of the 2-mm-diam tubes, which was then filled with tin. The maximum diameter of the coated wire was 0.5 mm, the bead of the thermocouple junction being no larger than the diameter of the wire. A plot of temperature vs distance traveled by the furnace is given in Fig. 1 for a rate of furnace travel of 1 cm per hr. The temperature gradient in the liquid

Jan 1, 1967

By L. Yarborough, L. R. Smith

This paper presents results of a laboratory study of retrograde condensate recovery by revaporization into dry injection gas. Flow tests were performed in 10.6-ft long sand packs at 100F and 1,500 psi. In three runs methane revaporized the liquid from a n-pentane-methane mixture in the presence of immobile water. TWO of these tests were water-wet, and the third was totally oil-wet. In the three runs n-pentane recovery was complete after 2.5 hydrocarbon PV of injection. There was no significant performance difference between the two wettability extremes. In a fourth experiment, a methane-hydrogen sulfide mixture revaporized a synthetic light, sour condensate. No water saturation was present. Equilibrium compositions and volumetric data were obtained for the four-component condensate. The heavy component, n-beptane, was removed after 6 PV production. Comparison of the effluent fluid compositions with known equilibrium data shows that the flowing fluid was equilibrium vapor and that the mixing zone between equilibrium vapor and dry injection gas was short. Data indicated that complete recovery of retrograde liquid occurred after it was contacted by a sufficient quantity of dry gas. INTRODUCTION When pressure declines below the fluid dew point in a gas condensate reservoir, a liquid phase forms. In this process, referred to as retrograde condensation, the quantity of liquid formed is frequently small enough that the liquid is not a flowing phase. To prevent loss of valuable retrograde liquids, the process of dry gas cycling has been employed for several years as a more or less standard practice. In this procedure the reservoir pressure is maintained above the fluid dew point so that the liquid components may be produced as vapor and then separated at the surface. Although full pressure maintenance by gas cycling seems ideal in terms of preventing liquids loss, several factors can reduce the atuactiveness of such an operation. From a study of a condensate reservoir in Alberta, Canada, Havlena et a1.1 con-cluded that cycling under conditions of declining pressure leads to economic advantages and to a high recovery of hydrocarbon liquids. This study considered effects of volumetric sweep efficiency, retrograde behavior of the original wet gas and revaporization characteristics of the retrograde liquid when contacted by dry gas. The first major work concerning revaporization of liquid in a gas condensate system is that of Standing et a1.2 Calculations based upon the PVT behavior of a recombined gas condensate fluid indicated that all retrograde liquid can be recovered if it is contacted by a sufficient quantity of dry gas. The paper considered the effect of variable permeability upon the recovery of retrograde liquid. Standing et al. concluded that recovery of heavier components in the retrograde liquid is greatest if reservoir pressure is allowed to decline below the dew point prior to dry gas injection. Since the work of Standing et al., several laboratory studies have been reported which show that recovery of hydrocarbon liquids by vaporization into dry injected gas can contribute to increased recovery above that obtained by ordinary production practices. Vaporization from retrograde condensate,3 conventional oil4-7 and volatile oil8 reservoirs has been considered. There is little work that deals with revaporization recovery from condensate reservoirs. This study demonstrates that vapor-liquid equilibrium exists when a dry gas is injected into a porous medium containing retrograde condensate; investigates the effect of wettability on revaporization of retrograde condensate; and provides an indication of the amount of dry gas necessary to

Jan 1, 1969

By M. H. Childs, K. E. Merklin

Blast furnace feed specifications are being revolutionized because of the large increase in iron pellet production from low-grade ores of the Lake Superior region. Recent laboratory findings aimed at a better understanding of factors influencing the physical quality of pellets produced from taconite concentrates are reviewed. Tests for determining better product quality, the effects of additives, and production factors are discussed. The current revolution in specifications for blast furnace feed is typified to a great extent by the recent tremendous growth in iron ore pellet production from low grade ores of the Lake Superior region. Indeed, pellets are responsible, at least in part, for many of the stringent new requirements that are being placed on the suppliers of furnace raw materials. As the tonnage of pellets going to the steel mills increases, more and more attention is being turned to the detailed characteristics that make this product an ideal blast furnace feed. Control of quality in pellets is similar to that of any other product. A basic understanding of the factors that are encountered in their production, from the crude ore through to the finished product, is required, along with careful process supervision and frequent quality checks. Normally, chemical grade is not a problem. This usually can be controlled within the desired specifications by minor operating variations in the con- centrator. While future changes in requirements may result in the need for self-fluxing pellets1 or other chemical changes, today's quality demands center primarily around the physical characteristics of the pellets. It is in this area that many of the recent laboratory studies have proven helpful to the operating plants. A better understanding of the physical factors involved in pelletizing has provided the basis for a continuing program of quality improvement. Tigerschiold and Ilmoni2 and Cooke with various associates are responsible for the development of much of the basic understanding of the pelletiz-ing process. These earlier findings have served as a most useful background for this work. LABORATORY PROCEDURES Magnetite concentrates produced from eastern Mesabi Range magnetic taconites were used for all of the work reported herein. The sizing and chemical analysis of a random sample are shown in Table t Additives usually are mixed with the concentrates in taconite plants before pelletizing to improve the strength characteristics of the unfired balls. Ben-tonite, soda ash, and coal are in common use. The bentonite used in these studies was of the Wyoming sodium type; the soda ash was a standard commercia1 brand. Anthrafines were used where coal was called for. The procedure for making batches of balls at the Hibbing Laboratory is as follows: In an especially designed mulling equipment 2800 g of dry ore are mixed for 10 min with the desired additives. Water is added and mixing continued for 1 1/2 min. The charge is removed from the muller and put through a mechanical shredder to break down any lumps that may have formed. sixty previously formed seed balls are placed in the balling drum, which is in fact a 6 x 16-in. diam airplane tire turning at 53 Wm. Two thousand grams of the shredded concentrate and additive mix are fed by hand into the tire at a con-

Jan 1, 1961

By W. M. McKewan, R. G. Olsson

In order to improve the understanding of the iron oxide reduction mechanism, the rate of equal molar diffusion of hydrogen and water vapor was measured through disks of porous iron and alumina. The measuretneizts were made at atmospheric pressure at 800°, 900- , and 1000°C. It is shown tint the reduction of dense hematite pellets with hydrogen at these temperatures and at atmospheric pressure is to a great extent limited by gaseous diffusion between the bulk-gas phase and the iron-wustile interface. THE investigation of the reduction of iron oxides with hydrogen has been the subject of numerous papers. Although the effects of temperature, pressure, and gas composition on the rate of iron oxide reduction have been studied, the actual mechanism of the reduction process has not been definitely determined. As a means of improving the understanding of the mechanism, the rate of equal molar counterdiffusion of hydrogen and water vapor was measured through porous iron and porous alumina disks at reduction temperatures. The alumina was used as a basis of compari-son because its pore structure is homogeneous and independent of temperature. The porous iron was prepared by the reduction of dense hematite disks with hydrogen at the temperature of the subsequent diffusion experiment. The hematite disks were made from pellets that were identical to those used by McKewan1,2 in his study of iron oxide reduction with hydrogen. In these investigations the weight loss and rate of movement of the various interfaces were measured as a function of the reduction temperature and gas composition. With these reduction data and the presently reported diffusion data it is possible to determine the importance of H2-H2O transport between the bulk-gas phase and the Fe/FeO interface to the reduction of dense hematite. APPARATUS AND PROCEDURE A porous iron or alumina sample was held in the base plate of a sealed canister containing porous granular wustite, as illustrated schematically in Fig. 1. The canister was suspended from an automatic recording balance in a vertical tube furnace through which flowed hydrogen and water-vapor mixtures of known composition at atmospheric pressure (0.96 atm). Hydrogen from the gas stream diffused through the porous sample, reducing the wustite in the interior of the canister. The water vapor that was formed diffused back to the gas stream. The rate of diffusion was determined from the recorded weightloss data. The furnace, automatic balance, and gas-metering equipment have been described previously.2 The main body of the canister and the tubing extension were made of stainless steel while the base plate was made of high-purity iron. The main body of the canister was % in. in diam. It held approximately 6 g of porous granular wustite that was prepared by reducing 0.1- to 0.2-cm-diam specular hematite particles at 900°C with an H2-H2O mixture of a composition near the iron-wustite equilibrium value. The upper end of the 1/8-in.-diam tubing extension was sealed with a segment of plastic tubing and a tubing clamp. The temperature at the top of the furnace was sufficiently high so that no water vapor condensed inside the extension. In the experiments with porous iron, iron oxide samples were prepared from reagent-grade hematite that was pressed and sintered in a manner previously described.' The resulting pellets had a density of 5.15 ± 0.05 g per cu cm. Each pellet was centerless-ground

Jan 1, 1967