Search Documents

The Committee on Papers and Publications has set June 1, 1919, as the closing date for the receipt of manuscripts intended for the Chicago meeting, which is to be held Sept. 22 to 27, 1919. Manuscripts must be received by the Secretary on or before this date. If they are sent through members of the technical committees, they must be sent to those committees long enough in advance to be forwarded and in the hands of the Secretary by the time specified.

Jan 5, 1919

By N. A. Hasenack

A full description of tests and test results of potgrate--as well as industrial tests is given. It is concluded that the favorable effects of magnetite ores on the pelletizing-plant results can almost be obtained by replacing the magnetites by hematites with coke breeze. The amount of coke breeze to be added should be about 30% above the theoretical value which is derived from the transition heat of the magnetite. The total amount of coke breeze should be limited to 1.5%.

Jan 1, 1977

By C. A. Shook, W. H. W. Husband, D. B. Haas

Introduction Although previous studies1,2,3 have been made, no correlations for pressure drop have been proposed. This is probably because severe particle breakage occurred and pressure drops changed substantially with time. A quantitative statement of the relationship of pressure drop to the parameters of the system is desirable for lignite since, unlike higher rank coals, lignite slurries are thixotropic. The present investigation was undertaken to quantify the pipeline behavior and required continuous monitoring of pressure drop and size distribution.

Jan 1, 1980

By E. F. Reed

CONSIDERABLE deep hole prospect drilling has been done in the last few years in the Globe-Miami mining district about 70 miles east of Phoenix, Arizona, and in the San Manuel-Tiger area about 50 miles south of the Globe-Miami region. More than 205,000 ft of churn drilling have been completed by the San Manuel Copper Corp. at their property in the Old Hat Mining District in southern Pinal County. The deepest hole on this property is 2850 ft; there are 49 holes deeper than 2000 ft. At the adjoining Houghton property of the Anaconda Copper Mining Co., where only one hole reached 2000-ft depth, there were 27,472 ft of churn drilling and 3436 ft of diamond drilling. Three churn drill holes were deepened by diamond drilling methods. Near Miami in the Globe-Miami district the Amico Mining Corp. drilled four holes by combined churn and rotary drilling methods, the total amounting to 13,879 ft, of which 2256 ft were drilled with a portable rotary rig. In the same district, besides doing a large amount of shallow prospect drilling, the Miami Copper Co. drilled two holes of 2560 and 3787 ft, respectively, which were completed by churn drilling methods. The rocks encountered in drilling at San Manuel and Tiger are described by Steele and Rubly in their paper on the San Manuel Prospect' and by Chapman in a report on the San Manuel Copper Deposit? The rocks are well-consolidated Gila conglomerate, quartz , monzonite, and monzonite porphyry. In some places these formations stand very well while being drilled, and three holes were drilled without casing, the deepest of which was 2200 ft. In other holes faulted and fractured ground made drilling difficult. In the Globe-Miami district the deep drilling was done in the down-faulted block of Gila conglomerate east of the Miami fault and in the underlying Pinal schist. The geology of this area is described by Ransome.3 In the Amico holes the conglomerate varied from material consisting entirely of granite boulders and fragments to a rock made up of schist fragments in a sandy matrix; in the Miami Copper Co. holes there were more granite boulders and the material was poorly consolidated. Drilling was much more difficult and expensive in the Miami area than in the San Manuel district, mainly because of the depth of the holes and the formations drilled. All the deep hole prospecting described in this paper was done with portable rigs. The churn drill rigs were of several types, of which the Bucyrus-Erie were the most popular. Bucyrus-Erie 28L, 29W, and 36L rigs were used on some of the deeper holes on the San Manuel property. A few Fort Worth spudder types were tried, and the deepest hole at San Manuel was drilled with a Fort Worth Jumbo H. The spudder type is considerably larger than most other rigs used on this work and required a larger location site. The spudders were belt-driven machines with separate power units, and time required for setting up and moving was much longer than with the more portable drills. All the churn drilling was done by contractors or with machinery leased from them. A few of the contractors had complete equipment, including most of the necessary fishing tools. Unusual and special, fishing tools were obtainable from the supply companies in the oil fields of New Mexico or in the Los Angeles area. Most of the contractors used equipment with standard API tool joints, so that much of it was interchangeable. Failure of tool joints is one of the principal causes of fishing jobs. It can be minimized if the joints are kept to the API specifications and the proper sized joints are used in the various holes. The minimum sizes that should be used with various bits are as follows: 12-in. and larger bits, 4x5-in. tool joints; 10-in. bits, 3 1/4x4 1/4-in. tool joints; 8-in. bits, 2 3/4x 3 3/4-in. tool joints; 6-in. bits, 2 1/4 x3 l/4 -in. tool joints; 4-in. bits, 1 5/8 x2 5/8-in. tool joints. Two rotary drill rigs were tried at San Manuel on the same hole, and a portable rotary drill rig was used on the Amico drilling for test coring the formation and for drilling in holes 3 and 4. Rotary drilling differs from churn drilling or cable tool drilling in that the bit is revolved by a string of drill pipe and the cuttings are removed from the hole by a thin solution of mud pumped through the drill pipe. The principal parts of a rotary rig are the power unit, a rotating table to revolve the drill pipe, hoists to raise and lower the pipe and to handle casing, and a pumping system to circulate the drilling liquid. The rig used on the Amico property at Miami was mounted on a truck. The larger rig used on the San Manuel property was hauled by several trucks and had separate turntable and pumping units. Diamond drill coring equipment was used successfully with the rotary rig in the holes on the Amico property, To allow for 2 3/8-in. drill pipe with tool joints, 3 1/2-in. core barrels and bits were used. With the standard 3 1/2-in. core barrel there was considerable difficulty in maintaining circulation with mud, so a barrel was designed with a smaller inner tube and a broad-faced bit. This allowed coarser material to circulate between the barrels. Rock bits of 5 5/8 to 3 7/8 in. were used with the rotary rig for drilling between core runs. Diamond drill equipment is much lighter than churn drill tools, so that fishing tools can usually be obtained from supply houses by air express when needed. Three churn drill holes on the Houghton property at Tiger were deepened by diamond drilling with Longyear UG Straitline gasoline-driven-machines. The open churn drill hole was cased with 2 1/2-in. black pipe. In deep hole churn drilling, casing is one of the most important items, especially in drilling in unconsolidated material like the formations drilled by

Jan 1, 1952

By R. C. Gould, A. M. Skov, L. F. Elkins

Comparison of long term decline in oil production during cyclic waterflooding or pressure pulsing of part of the Driver Unit with steady injection-imbibition flooding in the Tex Harvey area led to large expansion of flood in the Driver Unit on the steady injection basis. While the flood has been successful, the major problem has been attainment of satisfactory oil production rates in most of the wells. Large volume fracture treatments of low capacity wells were unsuccessful in achieving sustained increases in production. A two-section area in the Driver Unit has already recovered 620 bbl of oil per acre by waterflood but other areas have not performed so well. Sun Andres water containing 300 to 500 ppm H,S is sweetened to 0.5 to 1 ppm H,S by extraction with oxygen-free flue gas. This prevents contamination of gas produced in the area and apparently it has reduced corrosion in minimum investment, thin-wall, cement-lined water dktribution systems. Cement-lined tubing in injection wells has mitigated corrosion as effectively as thick polyvinyl chloride films have, and at less cost. Introduction As reported in the literature the Spraberry field of West Texas has presented unusual problems for both primary production and waterflood ing. Earlier information from the Spraberry Driver Unit included conception and evaluation of cyclic waterflooding or pressure pulsing in a nine-section pilot test as an aid to extraction of oil from the tight matrix rock and as a boost to normal capillary imbibition forces An additional 5 years' operation in that area, and performance of expanded steady injection water-flood, now covering a total of 68 sq miles, are reported herein. In addition, since the Driver Unit is one of the largest waterfloods in areal extent in the U. S., many operating experiences are presented for the benefit of engineers concerned with operation of other Spraberry floods or with other waterfloods where this reservoir technology and/or water handling technology may be adaptable in part. These include: (1) attempts to improve producing well capacity through large volume fracture treatments, (2) long-term performance of water treating plants utilizing oxygen-free flue gas to extract H,S from sour San Andres water, (3) performance of thin-wall cement-lined pipe in water distribution systems including comparison between those sections carrying raw San Andres water and those carrying treated water, and (4) comparison of performance of various lining materials and subsurface equipment in water supply and water injection wells. These experiences are reported without regard to whether results are good, bad or indifferent. Since the operations reported are limited to the techniques, materials, and equipment actually used in the Driver Unit, no comparison is possible with results of other approaches used in other Spraberry floods or in waterfloods generally under different conditions. However, an attempt is made to quantify these experiences as much as possible in the space available to permit other engineers to select those parts applicable to eheir problems. Background The Spraberry, discovered in Feb., 1949, is a 1,000-ft section of sandstones, shales and limestones with two main oil productive members—a 10- to 15-ft sand near the top and a 10- to 15-ft sand near the base, having permeabilities of 1 md or less and porosities of 8 to 15 percent. Extensive interconnected vertical fractures permitted recovery of oil on 160-acre spacing from this fractional-millidarcy sandstone, but they made capillary end effects dominant. Primary recovery by solution gas drive is less than 10 percent of oil in place, with most wells declining to oil production of a few barrels per day when reservoir pressures are still in the range of 400 to 1,000 psi. Partial closing of the fractures with declining reservoir pressure is believed to be the cause of such low production rates at these relatively high reservoir pressures. In 1952 Brownscombe and Dyes proposed that displacement of oil by capillary imbibition of water from the fractures into the matrix rock might significantly increase oil recovery from the Spraberry, overcoming otherwise serious channelling of water through the fractures." A pilot test conducted by the Atlantic Refining Co. during 1952 through 1955 indicated technical feasibility of the process; but low oil production rates averaging I5 to 20 bbl/well/D failed to create significant interest in large-scale waterflooding at that time." Humble Oil & Refining Co. conducted a highly successful 80-acre pilot test during 1955 through 1958 with

Jan 1, 1969

By R. M. Goldhoff, H. J. Beattie

The high-temperature properties of a 1 Cr-Mo-V forging steel are described. A series of controlled heat treatments was designed to delineate the effects of austenitizing and tempering treatments, temile strength, and grain size on such properties. Studies indicate that the mechanical properties and their varlations under creep can be described by the initial metallurgical structures and their changes droPirzg exposure, particulavly the carbide reactions. Such structures are described and correlated with the mechanical properties. FOR many years the large steam turbine industry has relied on the 1 Cr-Mo-V type forging steel for critical applications. Because of its adequate heat resistance and relative economy, it is currently in use in the temperature range up to about 1050" to 1075°F. Attempts to understand the large property variations attainable in this steel involve the structural modifications due to the wide latitude in its heat treatment. The heat treatment essentially involves a two-step process which includes solution-ing of carbides in the austenite range followed by a suitable tempering treatment below the critical to adjust the level of properties. The latter step is referred to as "secondary hardening" and is basically an ordinary aging reaction involving carbides. In the commercial heat treatment of large components of such steel, homogenizing and stress-relief anneals may be included and have some importance in determining subsequent properties. Several studies of the engineering properties of this steel as a function of transformation micro-structure have been reported.1 3 However, in this steel the carbide reactions, which are a function of composition and heat treatment, appear to be the property-controlling factor rather than the micro-structure defined as a transformation product. Thus, the tempering resistance of this type of alloy steel is mainly a function of the size and distribution of alloy carbides.4 However, it is also necessary to consider the stability of the microstructure and the effect of dynamic carbide reactions on subsequent properties. It is the purpose of this paper to show the interdependence of properties and corresponding structures, particularly carbide reactions, developed for a limited set of controlled heat-treatment conditions applied to 1 Cr-Mo-V steel. MATERIALS AND PROCEDURE The material for this work came from a large production forging whose chemical composition is shown in Table I. The property data accumulated on this steel as a function of heat treatment were room-temperature tensile and smooth- and notch-bar creep rupture at 1050°F (notch geometry: shank diameter = 0.357 in., depth = 50 pct, radius = 0.005 in.). To achieve controlled structural variations the temperature and time of both austenitizing and tempering were varied in a manner to produce a series of eight steels each at one of two grain sizes and one of two hardness levels in proper combination for valid comparisons. This will be clear upon examination of Table I. Structural studies involved the use of optical and electron microscopy as well as X-ray and selected-area electron diffraction. To reveal the nature of carbide precipitations, electrolytic extraction techniques were used with subsequent analysis of the residue by X-ray diffraction. Weight losses of the steel specimens during electrolysis were measured and successive chemical fractionations of the residues were applied and checked by X-ray examination. The details of fine structural distributions, morphologies, and crystallography of the precipitates as well as dislocation distributions were investigated by examining in the electron microscope three common types of preparation. a) Relief Replicas. Mechanically polished sections were etched in 2 pct nital, replicated with a nitrocellulose film, which was shadowed by chromium vapor deposited at a glancing angle of 20 deg. b) Extraction Replicas. A thin film of carbon was vapor-deposited on the polished and etched surface. The carbon films were then etched off and gathered on electron-microscope supporting grids. The carbides left imbedded in the carbon replica in their original distribution were then examined crystallo-graphically by selected-area electron diffraction. c) Thin Films. Specimens were mechanically ground and polished down to a thickness of 0.001 to 0.003 in. Final thinning was done electrolytically in a "chrome-acetic" electrolyte. When holes began to appear in the foil, the voltage was interrupted and applied in several 1-sec bursts. Sections of the foil between holes were thin enough to pass a 100-kv electron beam that carries an image.

Jan 1, 1965

By J. Clair, H. Mirabel

The determination of the temperature and electrical potential distributicms in the cathodes of aluminum electrolytic cells is difficult. The reascms come from the various nature and the intricate three-dimensional geometry of the materials; besides thermal and electrical phenomena react upon each other. A method of calculation using a computer program applied to a mathematical model, figuring the cathode, is developed. Both of the thermal and electrical phenomena are simultaneously considered. Temperature and electrical potential distributions are finally obtained by successive iterations. Results are compared with measurements on industrial cells. Theoretical and practical applications of these studies are given. Up to the present time the study of the distribution of the temperatures and electric potentials in the electrodes, anode and cathode, of the electrolytic cells used for the production of aluminum was limited to one of the two aspects of the phenomena because of lack of a simultaneous method of calculation. For example, the anode or cathode drop was studied assuming that the temperatures in the iron and carbon are known, a method that obviously is very approximate since iron resistivity, in particular, greatly varies with temperature, which in turn depends on current density. Consequently we tried to find a method of calculation simultaneously taking into account both thermal and electrical phenomena. We proceeded to the study of the cathodes as an initial approach to the problem. Although the cathode and surrounding materials may have varied forms and particularly very heterogeneous characteristics, their structures are simpler than that of the Sijderberg anode and boundary conditions are more easily represented than in the case of anodes even though they are prebaked. The study was in two parts: a) development of a model schematizing the true geometry of a cathode and defining the thermal and electrical boundary conditions, and b) working out a method of calculation of the temperatures and potentials by means of an electronic computer. To facilitate solution of the problem, a model was used initially much simplified in comparison with an actual cathode. This model permitted development of the method of calculation. In a second phase, this model was adjusted to the study of actual cathodes and applied to different types of cells: low- or high-intensity cells, cells set up at ground level or above ground level, cells with cathodes more or less heat-insulated. Simultaneously measurements were made with cells equipped with cathodes of the types studied to compare the values resulting from calculation. The initial model was also used for general studies, in particular for studying the effects of current density in the carbon and iron. The results were confirmed or made precise by the model of the true cathodes. This report successively describes: a) the manner in which the model representing a cathode was worked out, with the simplifications and/or the hypotheses used, b) the method of solution of the problem by means of the electronic computer, and c) an example, stating the extent to which the results obtained may be realistic. Further the possibilities offered by such a study are examined. 1) CATHODE REPRESENTATION The purpose of this phase is to represent the cathode in the form of a so-called "mathematical model", that is with a simplified geometrical configuration, in order to meet the subsequent calculation requirements, while keeping to the true facts as closely as possible. This model further includes the thermal and electric conductivities with regard to temperature for the varied materials composing the cathode, as well as the thermal and electrical conditions at the model boundaries. 1.1) Guiding Principles. For calculating the temperatures and potentials the model is divided by trior-thogonal planes into a network of small elementary parallelepipeds. At the summit of these parallelepipeds' so-called mesh points, the temperatures and potentials are computed. The number of mesh points is of course limited by the capabilities of the computer, since 1) the number of equations to be solved depends on the number of mesh points selected, and 2) the amount of time spent by the computer considerably increases with increasing this number. These conditions call for the following requirements as concerns the model: a) Dimensional requirements: the calculation will be all the more accurate as the network is more closely meshed. Since the number of mesh points is limited in practice, it is necessary to restrict the dimensions of the model. b) Geometrical requirements: so as to make things easier in working out the network, the model must be given a simple geometry. In particular, it will be convenient to have the cathode so constituted that the surfaces limiting the cathode and the surfaces within the cathodes separating the different materials consist of triorthogonal planes. 1.2) Schematization of the Cathodes. After the tech-

Jan 1, 1968

By C. H. Li, R. J. Stokes

This paper compares the fracture behavior of tungsten rods in three conditions: recrystallized. recovered, and wrought. Notched specimens suhjected to a 50 in.-lb impact load showed ductile-brittle transitions at 700, 4.90°, and 440°C, respectinely. The recrystallized material had an equiaxed pain structure and jracbred by simple cleavage from a grain boundary source at all temperatures up to 700°C. The wrought and recovered material had an elongated fibrous structure and at low temperatures fractured by cleavage originating from the notch. As the transition temperature was approached cleavage was preceeded by more and more intergvanular splitting which deflected the crack front into planes parallel to the tensile axis. The enhanced toughness of wrought and recovered tungsten was attributed both to its inability to initiate cleavage because no pain boundaries were suitably oriented perpendicular to the tensile stress and to its inability to maintain cleavage because of intergranular splitting ahead of the crack. It has been appreciated for a long time in a qualitative manner that the room-temperature brittleness of fully recrystallized tungsten may be alleviated by working the material at relatively low temperatures.' More recently this difference in mechanical behavior between wrought and recrystallized tungsten has been examined quantitatively by measurement of the tensile properties as a function of temperature. In these experiments brittleness has been expressed in terms of ductility or reduction in cross-sectional area upon tensile fracture or in terms of the bend radius before fracture under bending.' This work has shown the existence of a fairly sharp transition from brittle to ductile behavior with an increase in temperature. The ductile-brittle transition temperature for recrystallized material is approximately 200°C higher than for wrought material. An increase in strain rate, small additions of impurity,' or an increase in grain size4 shift the respective transition temperatures to higher values, but the difference between them remains approximately the same at 200°C. A number of explanations for this embrittlement by recrystallization have been given. It has been blamed either on the concentration of impurity at the grain boundaries, the increase in grain size, or the change in texture which occurs upon recrystallization. The present paper examines the effect of different heat treatments on the notch-impact behavior of commercial powder-metallurgy tungsten rods. The change in the ductile-brittle transition temperature for this method of loading and the fracture mode has been related to the different mi-crostructures produced by heat treatment. EXPERIMENTAL PROCEDURE Commercial swaged powder-metallurgy tungsten rods 1-3/8 in. in length and 1/8 in. in diameter were machined to introduce a sharp V notch 0.030 in. deep. To change the microstructure from that of the as-received wrought material some of the specimens were subjected to an anneal in nitrogen either at 1300° or 1400°C for 8 hr or at 1600° or 2000°C for 1/2 hr. The notched rods were then placed in a miniature Charpy-type impact machine and struck at their midpoint (opposite the notch) with a hammer designed to deliver 50 in.-lbs of energy. The strain rate at the base of the notch was estimated to be approximately 100 sec-1 at the instant of impact. The specimens were heated in situ to the desired impact temperature. The microstructures produced by the various anneals were studied by both X-ray diffraction and metallographic techniques. Fig. 1 reproduces the microstructures observed metallographically following a 10-sec electroetch in a 10 pct KOH solution. Fig. l(a) shows the elongated fibrous grain structure of the as-received material. Following the anneal at 1300" or 1400°C the grain structure was still elongated as shown in Fig. l(b) but the etch pits delineated dense polygonized dislocation arrays within many of the grains. Occasionally a relatively dislocation-free recrystallized grain was found growing into the matrix. The anneals at 1600° and 2000°C resulted in complete recrystallization and some grain growth. The grains produced at 1600°C were still slightly elongated as shown in Fig. l(c) whereas the anneal at 2000°C produced equiaxed grains. The changes in grain size produced the expected changes in the X-ray back-reflection patterns; there was no indication either in the as-received material or the annealed material of any preferred orientation. RESULTS a) Impact Behavior. Fig. 2 reproduces the ductile-brittle transition curves measured in the manner described in the previous section. It can be seen that under these testing conditions the as-received

Jan 1, 1964

By J. L. Huitt, B. B. McGlothlin

The introduction of new fracture propping agents that are brittle but much stronger than sand created the problem of what loading strength is required for a propping agent to be effective in a given formation. It is shown that the load at which the propping agent crushes should exceed the load at which total embedment in the fracture faces is possible. Simple laboratory tests to determine loading strength of the propping agent and embedment in the fracture faces, and use of these data in selecting a propping agent for a given formation, are discussed. INTRODUCTION One of the most important factors in the design of hydraulic fracturing treatments is the selection of a propping agent that can effectively provide the fracture flow capacity needed for stimulation of a well. Sand, once generally accepted as being synonymous with propping agent in hydraulic fracturing, is now recognized as having limited effectiveness in many formations because of its low resistance to crushing. Sand particles are brittle and have relatively low strength. Because of this property, sand particles are crushed in rocks that offer high resistance to the penetration of fracture faces by the proppant particles when the fracture attempts to close under the action of the overburden load. For rocks that offer a high resistance to penetration, deform able particles are more effective propping agents than sand. However, for this same type of rock, a propping agent that does not deform, yet does not crush, is often more effective. Thus, a rigid propping agent with sufficient strength to prevent crushing is desirable. A method for determining the strength required for a rigid propping agent to function effectively in given formations is discussed. BEHAVIOR OF RIGID PROPPANTS AND FRACTURE FACES RELATED STUDIES An early qualitative description of the reaction of propping sand in fractures was given by Hassebroek et al.' In discussing fracturing in deep wells, the authors mentioned that even though propping sand entered the fractures, a high flow capacity did not result due to crushing or embedding of the propping sand. Dehlinger et al.2 in discussing the reaction of propping sand surmised that, because of the hardness of sand particles, deformation occurred in the fracture faces contacting the propping sand. In later studies,3,4 methods of determining the embedment of propping sand in fracture faces of soft rock and the critical load at which propping sand is crushed by the fracture faces in hard rock were discussed. In working with de-formable proppants, Kern et al. considered proppant particles to be deformed into cylindrical disks by action of the overburden and then pressed slightly into the fracture faces by further action of the overburden. Rixie et al.'0 reported on embedment pressure and presented a method of selecting a propping agent for use in given formations. The propping agents included sand, walnut shells and aluminum pellets. All these studies have contributed materially to a better understanding of propping agent behavior; however, the strength of brittle proppants (sand, glass and ceramics) required to result in embedment rather than crushing has not been discussed. This topic will be covered in the ensuing discussion. PROPPANT PARTICLE CRUSHING—-EMBEDMENT For this discussion, a rigid propping agent is considered to be one that is brittle and fails under tensile stress when loaded to a critical value. In an earlier study4 it was shown that the Hertzian4 loading theory could be applied to a spherical brittle propping agent if the propping agent and fracture faces behaved elastically. At the failure of the proppant, the ratio of the load to the square of the diameter of the particle should be constant for a given material combination, or: Lc/dp2=C ............(1) A partial derivation of this equation from proppant and formation properties is included in the Appendix. Should a rigid particle not be crushed as a load is applied, it embeds in the fracture faces. A study3 of particle embedment in fracture surfaces has been published. The embedment can be described by an equation based on Meyer's metal penetration hardness relationships: d1/dp=B 1/2[L/dp2]m/2..........(2) In Eq. 2, B and m are constants that are characteristic of the rock; the significance of the other terms is shown in Fig. 1. A STANDARD DEFINITION FOR PROPPANT LOADING STRENGTH Eq. 1 is useful in appraising propping agent strength," but it is strictly applicable only when the area of contact between a particle and a fracture face (or loading plate)

Jan 1, 1967

By E. Buehler, H. J. Levinstein

The temperature ranges in which the three inter-metallic phases in the Nb-Sn system form have been determined and the composition and structure of two of the three phases has been established. The kinetics of the formation of Nb3Sn in cored wire samples has been studied in the temperature range of 800° to 1050°C. From 800°to 950°C the rate of formation increases by four orders of magnitude. The rate-controlling step for the formation process in this temperature range appears to be the diffilsion of tin through NbSn. At higher temperatu~es a change occurs in the mechanism of the formation process such that up to a temperature of 1050°C the rate of formation of Nb3Sn does not increase above the rate observed at 950°C. For temperatures helow 950°C the current-carrying capacity of the wire increases with increased percent reaction reaching a maximum value when the formation process is 90 to 95 pct complete. The maximum current-carrying capacity obtainable in this temperature range is independent of the temperature. Above 950°C tlze current-carrying capacity obtainable in the wire decreases with increasing temperature of formation. A model is proposed which accounts for the ohserved behavior. RECENTLY, Buehler et a1.l reported the results of an investigation of the process variables which influence the superconducting properties of Nb3Sn-cored wire. These results indicated that at least four variables affect the properties of the manufactured wire. These include composition, particle size of the starting powder mix, temperature of heat treatment, and time of heat treatment. In order to understand completely the role of these variables, it is necessary to have an accurate knowledge of the phase equilibria in the Nb-Sn system. At the present time, phase-equilibrium diagrams for the Nb-Sn system have been published by a number of investigators.2-5 The diagrams differ as to the number of phases present, the composition of the phases, and the temperature range of stability of the phases. The present investigation was undertaken in order to resolve these differences. Since the investigation of Buehler et al. demon- strated that the length of time at the temperature of heat treatment affected the superconducting properties of Nb3Sn, it is apparent that it is necessary to understand the kinetics of the formation process as well as the equilibrium conditions before a complete understanding of the system is possible. As a result, the kinetics of formation of the various phases in the system were also studied in this investigation. EXPEFUMENTAL PROCEDURE Diffusion couples and sintered powdered compacts were employed in the phase-diagram investigation. The diffusion couples were made by filling 1/8-in.-ID monel-sheathed niobium tubes with tin. The monel sheath was employed to facilitate drawing.' The tubes were then drawn to a tin-core diameter of 32 mils. Samples approximately 3 in. long were then cut from the drawn composite. The tin was drilled out of the ends to a depth of 1/4 in. and niobium-wire plugs were inserted into the ends and peened over. The monel was removed by etching in concentrated nitric acid, after which the samples were sealed in evacuated quartz bulbs and heat-treated in a resistance-wound tube furnace. The samples were quenched into ice water upon removal from the furnace. The diffusion couple samples were examined metallographically employing a chemical etching solution consisting of 10 ml of saturated chromic acid per g of NaF. In addition, two anodizing solutions were used for phase-identification purposes. The first was the picklesimer7 solution; the second consisted of equal parts by volume of 30 pct H2O2 and concentrated NH4OH to which 1 g of NaF was added per 25 ml of solution. The anodizing conditions for the second solution were 2 v and 100 ma with a tin cathode. The powdered compacts were made by pressing previously mixed powders of 99.9 pct pure Sn and 99.6 pct pure Nb supplied by the United Mineral Co. into cylinders 3/8 in. in diameter by 1/2 in. long. The cylinders were then sealed in quartz tubes and heat-treated in the same manner as the diffusion couples. The samples were examined metallographically and by X-ray diffraction techniques. Since it was desirable to be able to correlate the kinetic data with current-carrying capacity, the type of specimen chosen for this part of the investigation had to be a compromise between the optimum system for studying kinetics and one which was suitable for making current-carrying capacity

Jan 1, 1964

By G. L. Fisher, R. H. Geils

The effect of small amounts of columbium (<0.01 to 0.10 pct) on the ?-a transformation occurring during the continuous cooling of a low carbon Ni-Cu steel was investigated. Dilatometer specimens were aus-tenitized at 950" and 1068?C and cooled at 17? and 375 C° per min. Columbium caused a marked depression in the ?-a transformation temperature except when cooling at the slower rate from 950°C. The effec of columbium on the transformation temperature was greater the higher the austenitizing temperature and rate of cooling. A maximum depression of 92 C" was observed. Metallographic examination of specimens of <0.01 and 0.07pct Cb steels heated at 1200°C for 1 hr and cooled at various rates showed that columbium had a major effect on the ferrite morphology. The fer rite in the columbium -free steel remained equiaxed at cooling rates as high as 440 C? per min while the columbium-bearing steel exhibited mixed structures o equiaxed and bainitic ferrite at cooling rates as low as 130 C° per min. The ? grain boundaries in the columbium -free steel provided the ferrite nucleation sites in rapidly cooled specimens. There was a complete absence of nucleation at these sites in the colum bium-bearing steel. It is concluded that columbium depresses the transformation temperature by suppressing ferrite nucleation at the austenite grain bound-aries. In this respect the effects of columbium are analogous to those of boron in low C-Mo steels. It is well known that small columbium additions can substantially strengthen plain carbon steels. As little as 0.02 pct Cb can increase the yield strength of mild steels by 10,000 psi.1 A fine precipitate of CbC has been observed in columbium-bearing steels2 and is generally thought to be responsible for the strengthening. Little attention has been devoted to the effect of columbium on the ?-a transformation. Webster and woodhead3 have studied the effect of columbium on the isothermal proeutectoid ferrite reaction in mild steels. They found similar transformation behavior in steels both with and without columbium additions. However, as the austenitizing temperature increased, the incubation time for the start of the ferrite transformation became longer in the columbium-containing steel. Morrison1 found that the addition of 0.03 pct Cb to a C-Mn steel lowered the transformation temperature by 50 C° during cooling from 1200°C at a rate of 80 C" per min. The strengthening effect of columbium has recently been utilized in an age-hardenable, low-alloy steel containing copper and nickel.4 A small amount of columbium has a substantial effect on the as-rolled strength of this steel. By increasing the columbium level from <0.01 to 0.13 pct the as-rolled yield strength is increased by 15,000 psi. Columbium also significantly lowers the ?-to-a transformation temperature of this steel during continuous cooling from the austenitizing temperature. Because of the low carbon level in this steel (0.05 pct max), it is almost entirely ferritic. Thus, it offers the opportunity of studying the effect of small columbium additions on the proeutectoid ferrite reaction. Of particular interest in this study was the reason for the marked lowering of the transformation temperature by columbium during continuous cooling. EXPERIMENTAL PROCEDURE Materials. The compositions of the steels used in this investigation are shown in Table I. The steels were 30-lb air induction melts. They were forged to 4 by 8 by 1 in. plate at 1230°C, air cooled, and then reheated to 1230°C and cross-rolled in two passes to in. plates. Dilatometry. A Leitz Bollenrath dilatometer was used to record the transformation during continuous cooling from two different austenitizing temperatures. The dilatometer specimens were + in. in diam and 2 in. long. Oxidation and decarburization of the specimens was prevented by maintaining a small positive pressure of dry argon in the dilatometer furnace and by plating the specimens with 1 mil of Cu. For the lowest cooling rate, 17 C" per min, the temperature of the specimen was measured with a Pt-Pt 10 pct Rh thermocouple placed in a & in. diam well in the center of the specimen. During air cooling, 375 C° per min, this method of measuring the temperature interfered with the operation of the dilatometer. However, it was found that the temperature of the specimen could be measured accurately by placing a thermocouple in an identical specimen in a holder adjacent to the one being used to operate the dilatometer mechanism. The dilation-temperature curves were recorded on photographic film and then converted to volume percent ferrite-vs-temper-ature curves. The cooling rates obtained with the dilatometer are shown in Table 11. Cooling rates of

Jan 1, 1970

By B. C. Wonsiewicz, W. W. Wilkening

Following a procedure proposed by Wheeler and Ireland, Plane stress yield loci were constructed from Knoob hardness numbers. Basically, six differently oriented hardness measurements were made on three orthogml surfaces through pure poly crystalline magnesium sheet, a magnesium single crystal, and sheet of the magnesium alloys: Mg + 0.5 pct Th, Mg + 4 pct Li, AZ31B, and EKOO. Hardness loci were found to be in poor agreement at small strains (E < 0.05) with loci established by a more rigorous technique. At larger strains (E - 0.10) the agreement is fair, but at this stage in deformation the conventional locus has lost much of the asymmetry that characterizes these anisotropic materials. Two effects which will lead to distortions in the Khn locus are discussed with reference to the geometry of plastic flow during a hardness test. DETERMINING a material&apos;s resistance to multiaxial loading is of interest not only from a structural design viewpoint but also from that of deformation processing. Unfortunately, the determination of the yield locus, although simple in principle, involves tedious procedures if the results are to be at all rigorous.&apos; The idea, first proposed by Wheeler and 1reland2 of determining the yield locus by means of six Knoop hardness impressions along the principal directions in a material has obvious appeal. It is simple, quick, and should be applicable to very thin sheets. If such a technique could be demonstrated to produce consistently reliable results, it would be of interest to both researcher and designer. Lee, Jabara, and ackofen have compared the yield locus determined by Knoop hardness measurements (the Khn locus) to a locus determined by more rigorous techniques. They found good agreement for two titanium alloys at a plastic strain of about 1 pct. The purpose of this paper is to investigate if the Khn locus construction is a reasonable approximation to the locus of a highly anisotropic material. Examples of such materials are magnesium and magnesium alloys which have severely distorted yield loci which in turn reflect markedly dfferent yield strength in different directions.&apos; In pure magnesium, for example, the yield stress in tension along the transverse direction may be four times the yield stress in compression in the same direction and twice the tensile yield stress in the rolling direction. Predicting such large differences ought to serve as a severe test of the Khn locus construction. EXPERIMENTAL PROCEDURES Samples of rolled sheet, 0.250 in. (6.35 mm) thick, of pure magnesium and four magnesium alloys (Mg experimental materials. The pure magnesium together with the lithium and thorium alloys were those used in the study of Kelley and Hosford. The grain size was ASTM number 4 for the pure magnesium and number 6 for the alloys. HARDNESS TESTING The materials were sectioned along the rolling and transverse planes, mounted in a quick setting resin, and mechanically polished. Most of the hardness tests were performed on a surface prepared by electro-polishing (30 pct nitric acid in methanol at 0°C and 20 v) with the exception of the AZ31B and EK00 alloys which were made directly on a metallographically polished surface. However, subsequent hardness tests on the same sample after heavily electropolishing, revealed essentially the same hardness as before. At least twenty Knoop hardness impressions under a 100-g load were made in each of the six orientations shown in Fig. 1. The average hardness number and standard deviation were then calculated for each orientation. CONVENTIONAL LOCUS CONSTRUCTION Yield loci were constructed using a technique described in detail by Lee and ackofen,&apos; in which the flow stress (stress at a given plastic strain) fixes the coordinates of a point on the locus and measurements of the strain ratio serve to establish the slope of the locus at that point. The loading paths which correspond to uniaxial tension or compression tests establish the four intercepts of the locus with the coordinate axes plus one point on the balanced biaxial tension line Tensile testing was performed along the rolling and transverse (r, t) directions. Samples had a uniform rectangular gage length 1 by 4 by 4 in. (25.4 by 6.35 by 6.35 mm) and were deformed at a strain rate of 3.33 x 104 sec-&apos;. The tests were interrupted periodically to unload the sample and measure the plastic strains by means of X-Y post yield strain gages. Compression tests in the rolling, transverse, and through-thickness (r, f, z) directions were performed on 1/4 in. (6.35 mm) cubes at an initial strain rate of 8.33 x sec-&apos;. Lubrication was provided by 0.002 in. (51 pm) Teflon sheet which was renewed after unloading for micrometer measurements used to calculate the strains.

Jan 1, 1970

By J. R. Elenbaas, J. A. Vary, D. L. Katz

The development of gas fields, oil fields and aquifers for storing natural gas is treated from two main vieu.-points: (I) the volumetric storage capacity for gas in a given situation and (2) the prediction of the number of wells required for the delivery of gas. Other experiences in the design and operation of storagc fields are incluclerl INTRODUC TION Storage of natural gas in underground reservoirs near the terminus of long distance pipelines has been the prime factor in opening the space heating market to the natural gas industry. Storagc has permitted a major. increase in both the load and the load factor of pipe-lines; some are now operating at steady load throughout the year. Thus, underground storage has been responsible for the rapid increase in demand for natural gas in recent years. Three types of reservoirs have been used for gas storage: natural gas reservoirs, oil reservoirs, and waterbearing sands or aquifers. This paper presents the factors to be considered when developing gas storage reservoirs of these three categories. There are two prime considerations tor any storage reservoir: (1) the volume of gas which a given reservoir will store advantageously and (2) the number 01 wells needed to provide the required peak deliverability. These two problems will be considered for the three types of reservoirs just noted STORAGE IN PARTIALLY DEPLETED GAS FIELDS Early storage operations consisted of replenishing the natural gas in a depleted gas field situated adjacent to the market. Today, newly discovered fields near the market may be considered for storage, and this discussion applies equally to both types of reservoirs. For reservoirs originally containing gas or oil, the question of the impermeability of the cap rock nor-mally does not arise. However, such fields are likely to have many wells drilled either to or through the reservoir under consideration. Positive assurance must be obtained that such wells are or can be made mechanically tight. Corroded casings may need to be lined or permanently plugged. Abandoned wells should bc reopened and properly cemented. The volumetric capacity for gas storage depends upon space available in the porous rock as well as pressure and temperature of the gas in the reservoir. The production-pressure decline data on partially depleted gas reservoirs without water drive permit calculation of the reservoir space for gas. Isopachous maps of sand volume and porosity data for the reservoir rock provide an alternate method of calculating the pore volume for water-drive reservoirs. The pressure range selected for the storage cycle depends upon ()) the safe upper limit of pressure. 2) the flow capacity of wells and (3) compression requirements when injecting gas into the reservoir or delivering to market. Normally, gas and oil fields have pressures at discovery in the range of 0.43 to 0.52 psi/ft of depth. Pressures of around 1.0 to 1.2 psi/ft of depth appear to lift the overburden1-3 and invite uncontrolled movement of fluids in the porous rock. Some top pressure is normally selected for a storage reservoir ranging from below discovery pressure for deeper reservoirs to 0.65 psi/ft of depth for shallower reservoirs. Pressures to 0.66 psi/ft have been experienced without difficulty. The lower pressure limit is set by water intrusion accompanying low pressures, reduced flow capacity for wells at lower pressures and compression requirements. Depletion-type gas reservoirs often encounter water problems in the later stages of gas production. Such water intrusion may be due to movement from the surrounding aquifer. Accordingly, displacement of this water back into the aquifer by gas pressure and subsequent surges of water corresponding to the gas storage pressure cycle must be considered. Storage fields often produce in four months a volume of gas equal to its initial content. Rapid decreases in reservoir pressure occur, such as 20 psi/day. Accordingly, closed-in pressure observation wells which reflect the pressure in the bulk of the reservoir are required for following the operation of the reservoir. It has been found that a plot of observation wellhead pressures against gas content, Fig. 1, is very useful in observing operation of the field, checking the inventory and predicting future behavior. The plot is based on a given quantity of base or cushion gas in place. The injection and withdrawal curves may spread depending upon the homogeneity of the reservoir rock. permeability of the rock, well spacing and flow rates.

By R. O. Williams

It is shown that Ni3Al precipitates homogeneously from nickel-rich alwminum alloys as plates on the (100) planes. Prior to actual precipitation a process occurs which is believed to be one of increasing short-range order. After precipitating the Ni3Al plates enlarge through competitive growth. Discontinuous precipitation can occur simultaneously with the above processes. Recent ideas of the origin of precipitation strengthening appear adequate to explain the hardness changes. REMARKABLY little appears to be known about the precipitation process in Ni-Al alloys in spite of their technical importance. This investigation originated to supply additional information about precipitation in general, this system in particular. Information on the structures and kinetics have been obtained through the use of hardness, X-rays, microscopy, calorimetry, and resistivity on high-purity alloys. PROCEDURES Six alloys, Table I, were prepared by melting carbonyl nickel and high-purity aluminum in alumina crucibles in vacuum and casting into 1-in. graphite molds. All rods were homogenized at least once at 1300°C for 24 hr prior to swaging and this was repeated on the first three alloys after 75 pct reduction. Alloy 4 could be reduced only 10 pct at 1000°C (probably in two-phase field) prior to fracture but 1/4-in. samples quenched from 1100°C were readily reduced cold. Alloy 5 was reduced 15 pct cold but failed on the next pass while alloy 6 of essentially the same aluminum content failed inter-granularly without apparent flow up to 1000°C. The alloys were heated in hydrogen at the elevated temperatures and formed thin, coherent aluminum oxide coatings which provided excellent oxidation resistance at lower temperatures. However, freshly prepared surfaces showed considerably less resistance at 500"to 700°C in air and apparently resulted in internal oxidation. As a consequence, low-temperature agings were carried out in evacuated tubes. RESULTS The isothermal hardening behavior of these alloys at 500"and 565C is given in Figs. 1 and 2. These results were obtained from samples cold worked 75 pct, recrystallized at 1000°C (1100°C for the 7.8 pct Al) and quenched in water. This recrystallization was used to give smaller grain sizes so as to obtain more uniform hardness values and the points represent an average of five readings. The electrical resistivity was measured on 1/16-in. wires quenched from 1000°C during aging at 495°C to give Fig. 3. The energy release and its rate are given in Fig. 4 for the 6.9 pct Al alloy during aging around 500°C. Inasmuch as this was a single run, its accuracy is not known but certainly the general shape and magnitudes are correct. The method used to obtain these results is described elsewhere.&apos; Data for the aging at 600°, 700°, and 800°C of these alloys cold worked 50 pct are given in Fig. 5. Supplementary information from microscopy and X-ray diffraction have been included to indicate recrystallization, discontinuous precipitation and the appearance of superlattice lines from the Ni3Al. The hardness of these alloys as annealed, aged, cold worked, and cold worked and aged is given vs composition in Fig. 6. Those samples which were isothermally aged, Figs. 1 and 2, were reaged at 532°C and at successively higher temperatures for the indicated times to give the data of Fig. 7. These results as well as certain others, support the idea that the level of hardness reached for temperatures above 600°C are equilibrium values more or less independent of path. This being the case, the breaks in the curves would be the complete solution of the Ni,Al. The electrical resistivity versus temperatures for some of these alloys, both aged and unaged, is given in Fig. 8 along with those data from heating slowly (10 deg per day) to high temperatures. Interesting points include the lowering of the Curie temperature (the change in slope), the lack of any indications of a solubility limit and the large temperature coefficient for the Ni3Al. A slight break for Ni3Al around 100C shows up but this is not a Curie temperature as Ni3Al is not ferromagnetic down to -190°C. Metallographically both the nickel-rich solid solution and the Ni3Al appear very much like pure nickel. Profuse twin boundaries are present both

Jan 1, 1960

By F. M. d’Heurle

Films of molybdenum have been prepared by sputtering onto oxidized silicon substrates. The resistivity. lattice parameter, orientation, and grain size were studied as a function of substrate temperature and substrate bias. Under normal sputtering conditions, the resistivity of the films was found to be quite high (600 x 10 ohm-crn). However, with the use of the negative substrate bias of 100 v and a substrate temperature of 350°C, films weve produced with a resistivity of ahout twice that of bulk molybdenum. The lattice parameters measured in a direction nornzal to the surface of the films weve found to be gveatev than the bulk value. This was interpreted as being at least partly due to the presence of compressive stresses. The effects of annealing in an Ar-H atmosphere were studied in terms of diffraction line width, lattice parameter, and resistivity. BECAUSE of its relatively low bulk resistivity (5.6 x 106 ohm-cm)&apos; molybdenum is potentially interesting as a thin-film conductor in integrated circuits. An additional feature which makes it attractive for this purpose is its low coefficient of expansion (5.6 x KT6 per "c),&apos; which is fairly well matched to that of silicon (3.2 x 10 per c). It is possible to deposit molybdenum films by evaporation but generally films produced in this manner have a high resistivity. In order to achieve resistivities close to bulk value, Holmwood and Glang found it necessary to operate in a vacuum of about 107 Torr and to maintain the substrates at 600 C during film deposition. Sputtered molybdenum films have been examined by Belser et a1.7 and, recently, by Glang et al.&apos; This paper describes the results of an attempt to extend some of that work and examine the effects of annealing and getter sputtering on the physical and structural properties of the films produced. SPUTTERING APPARATUS AND PROCEDURE The apparatus used for most of the film sputtering work described here consisted of two "fingers" serving as anode and cathode, respectively, which were mounted within an 18-in.-diam glass chamber. A liquid nitrogen-trapped 6-in. diffusion-pump system was used to achieve a vacuum of about 1 x 107 Torr within the chamber prior to sputtering. The essential features of the equipment are shown in Fig. 1. Cathode and anode fingers are stainless-steel tubes isolated from the top and bottom plates by Teflon collars. In order to limit the discharge to the space between anode and cathode, each finger is surrounded by an aluminum hield, at ground potential, having an internal diameter 18 in. larger than the outside diameter of the finger. The cathode and anode fingers are 6 and 4 in. in diam, respectively. A 116-in.-thick sheet of molybdenum is brazed with a 10 pct Pd, 58 pct Ag, 32 pct Cu alloy to a copper disc which is mounted by means of screws and a large 0 ring onto the lower end of the cathode finger. The disc is cooled during sputtering by water circulation inside the finger. The use of several feet of plastic tubing for the water input and outputg reduces leakage to ground to less than 1 ma when the cathode potential is raised to 5 kv. The upper end of the anode finger is terminated by a brazed-on copper block. A variety of specimen holders can be easily mounted on the upper face of this block. Substrate heating or cooling is achieved by use of an appropriate unit attached to the lower face of the same block. Heating is achieved by means of cartridge-type heaters and cooling by copper coils fed with forming gas under pressure. The inner chamber of the specimen finger constitutes a small vacuum chamber of its own which is evacuated by an auxiliary mechanical pump in order to limit heating element oxidation and heat transfer by convection currents. An advantage of the finger arrangement is the absence of cooling and heating coils and wires within the main chamber. The stain less-steel shutter is useful to establish a discharge for cleaning the cathode at the beginning of each sputtering run. Water cooling of the shutter reduces heating and the out-gassing of impurities which might condense on the nearby substrates. Unless otherwise specified, the substrates used in these experiments were 1-in.-diam oxidized silicon wafe:s, 0.007 in. thick, having an oxide thickness of 6000A. The substrate holders were large copper discs onto the surface of which a number of molybdenum discs, 116 in. thick and 78 in. in diam, were brazed. The wafers were clamped to the molybdenum discs

Jan 1, 1967

By Clarence O. Babcock

Model pillars of limestone, marble, sandstone, and granite, with length-to-diameter (LID) ratios of 3, 2, 1, 0.5, and 0.25 (0.286 for granite), were broken in axial compression to determine to what extent an increase in end constraint increased compressive strength. Radial end constraints of 13 to 23% of the average axial stress in the pillar, produced by solid steel rings bonded with epoxy to the ends of dogbone-shaped specimens, increased compressive strength somewhat above that of cylindrical pillars without ring constraint. However, when the results were compared with those obtained by other investigators for straight specimens of several rock types taken collectively, with LID ratios greater than 0.5, the resulting strengths were not significantly different. Thus, the amount of end constraint produced by the solid steel rings was about the same as that produced by the friction from the steel end plates. In other tests, a radial prestress of 3000 or 5000 psi was applied prior to axial loading by adjustable hardened steel rings to increase the constraint above that obtained for the solid rings. The average radial constraint stress, expressed as a percentage of the average axial pillar stress at failure for the 3000 psi prestress, was 54.3% for limestone, 40.3% for marble, 44.7% for sandstone, and 23.4% for granite. The average radial constraint stress, expressed as a percentage of the average axial pillar stress at failure for the 5000 psi prestress, was 74.2% for limestone, 51.2% for marble, 61.6% for sandstone, and 29.7% for granite. These constraints increased the compressive strength significantly above the strength of straight specimens and solid-ring constrained specimens. These results suggest that large horizontal stresses in orebodies mined by the room-and-pillar method should increase the strength of the pillars and allow an increase in ore recovery by a reduction of pillar size when major structural defects are absent. One important objective of the U.S. Bureau of Mines (USBM) mining research program is the rational design of mining systems. In the design of room-and-pillar mining operations, pillar strength is a fundamental variable. It is customary to estimate this strength from uniaxial compression tests of rock samples and to correct this value for the length-to-diameter (LID) ratio of the in-situ pillar. This method of estimating pillar strength corrects for pillar shape but does not consider the effect of a large horizontal in-situ stress field that sometimes exists in underground formations. The purpose of the work covered in this report was to determine to what extent the compressive strengths of model pillars of relatively brittle rock loaded in axial compression were affected by lateral end constraint. In previous work, Obert l used solid steel rings bonded to the ends of dogbone-shaped specimens to study the creep behavior of three quasi-plastic rocks -salt, trona, and potash ore - during a test period of 1000 hr. These rings provided radial constraint during the loading cycle of 20 to 50% of the axial stress for specimens with LID ratios of 2, 0.5, and 0.25. He concluded that (1) "for a quasi-plastic material the end constraint strongly affects the specimen strength, and (2) as D/L increases (length-to-diameter decreases), the specimens lose their brittle characteristics and tend to flow rather than fracture." He also concluded that model pillars constrained by rings were better for use in predicting the strength of mine pillars than either cylindrical or prismatic specimens. This conclusion appears to be valid where mine pillars, roof, and floor are a single structural element. In the present study, 460 specimens of four relatively brittle rocks — limestone, marble, sandstone, and granite - were tested to failure. The study consisted of two parts: (1) the effect on the compressive strength of end constraint produced during the axial loading cycle by solid steel rings bonded with epoxy to the ends of the specimens, and (2) the effect on the compressive strength of increased end constraint produced in part by a prestress applied prior to axial loading and in part by lateral expansion of the specimen during the loading cycle. The first part of this study was reported in some detail earlier.2 EXPERIMENTAL PROCEDURE AND EQUIPMENT Model rock pillars of the sizes and shapes shown in Fig. 1 were broken in axial compression when the ends were constrained as shown in Fig. 2. he straight specimens were broken without ring constraint. The specimens of dogbone shape were broken with (1) solid

Jan 1, 1970

By Marius S. Darrow, William B. White, Rustum Roy

The PbS-PbTe systen has been studied by quench-ing and D.T.A. techniques f?om 400&apos; to 1150°C. Runs were made in evacuated silica tubes so that all equilibria are at the vapor pressure of the system. Lattice parameters of the quenched salnples , measured by X-ray diffraction, show a complete crystalline-solution series existing over a narrow temperature range between approximately 805" and 871°C. An exsolution dome extends from a maximum of about 805"C (approximately 30 mole pct PbTe) to 1 and 96.5 pet PbTe at 400°C. A narrow melting region, deternined by D.T.A., extends form 918c (mp PbTe), The shapes of the liquides and solidus curves imply the existence of a minimum at 871°C at approximately 65 pct PbTe. THe exact composition of the minimum could not be established due to the very narrow two-phase region. At compositions containing less than 50 pet PbTe, liquidus temperatures begin to increase, while the solidus remains almost flat to about 15 mole pet PbTe before beginning to vise toward the mp of PbS (1075 C). LEAD sulfide and lead telluride are isostructural (NaC1 type) semiconductors whose electrical and optical properties have been extensively studied and used in recent years. If appreciable crystalline solution exists between these compounds, the variation of physical properties with composition could be of interest. The purpose of this investigation was to determine the extent, if any. of crystalline solution, and to obtain the phase diagram for the system. To the knowledge of the authors, only three studies of the system PbS-PbTe have been reported, and, in chronological order, each investigation found an increasing amount of crystalline solution. In 1956, Yamamoto reported finding no evidence of crystalline solution between the compounds. Sindeyeva and Godov-ikov,&apos; in 1959, found very limited crystalline solution. but only under conditions of excess tellurium concentration. Finally Melevski s3 investigation in 1963 indicated that one solid phase exists in the region from PbS to 7 pct PbTe and from 82 pct PbTe to PbTe at 886&apos;C, with an eutectic at 55 pct PbTe at that temperature. Detailed data on the solvus boundary were not given. EXPERIMENTAL EQUIPMENT AND MATERIALS Commercially produced PbTe and PbS powders were used as starting materials. Batches of specific mole percent composition were accurately weighed and mixed in a plastic bottle, in a shaker mill. An analy- sis of impurity content is given in Table I for pure PbS and PbTe and for two randomly selected batches after the powders were mixed. Individual samples, ranging in weight from 0.2 to 0.5 g, were sealed in evacuated silica tubes which had been thoroughly washed and rinsed with acetone and distilled water. Thus all data taken were at the pressure of the system. Subsolidus relations were studied down to 400°C by heating the samples in a vertical tube furnace for 24 hr. The sealed tubes were quenched in water with quench time from the hot zone not exceeding 1 sec. Temperatures were measured by a chromel-alumel thermocouple and controlled to 53°C for most runs. The number and composition of phases present were determined from powder X-ray diffraction patterns taken at room temperature on a Norelco diffractome-ter, using silicon as an external standard. Above 850°C quenching techniques were, in general, found to be unsatisfactory, and differential thermal analysis (D.T.A.) was used to determine melting relations. The evacuated tubes were recessed about 1 cm at one end to accommodate the differential thermocouple. Al203 was used as the reference material in a similar tube containing the other side of the differential couple. For temperature measurements, a separate thermocouple was placed in the recess of the tube containing the sample to be measured, thus providing an opportunity to obtain thermal, as well as differential, analysis. All thermocouples for these measurements were Pt-Pt 10 pct Rh. Temperature and differential curves were recorded separately on synchronized strip-chart recorders. Thermocouples and recording equipment were calibrated using NaCl and gold standards, using the melting points 801" and 1063 C, respectively, which span most of the temperature range of interest. Heating and cooling rates generally were from 4 to 7°C per min. It was found, in fact. that rates ranging from 1.5 to 25°C per min did not significantly change the data obtained.

Jan 1, 1967

By P. Pietrokowsky, T. E. Tietz, J. E. Dorn

The amount of solid solution hardening in aluminum alloys was found to be dictated by two factors: the lattice strain, and the change in the mean number of free electrons per atom of the solid solution. To obtain this correlation it was necessary to assume that aluminum contributes two electrons per atom to the metallic bond. WHEN the modern scientific method of analysis was first being formulated, Francis Bacon recorded in his "Essays" (circa 1600) that "an alloy . . . will make the purer but softer metal capable of longer life." During the intervening centuries voluminous data have been reported which demonstrate that the additions of alloying elements do in fact increase the hardness and strength of the pure metals. Nevertheless, the significant details of this problem on the unique effect of each element toward enhancing the mechanical properties of alloys only recently have been subjected to systematic scientific scrutiny. The major objective of this investigation is to determine how minor additions of alloying elements affect the plastic properties of polycrystalline aluminum alloys. By means of such studies it is hoped to provide not only data on the solution strengthening of aluminum alloys, but also a body of facts which will supplement the knowledge already available on the factors responsible for solution hardening in general. A review1"10 and analysis1&apos; of the existing data on the effect of solute elements on the plastic properties of solid solutions reveal that our current knowledge on solid solution hardening is somewhat meager, inconsistent, and inconclusive. Many of the inconsistencies are undoubtedly attributable to the influence of unsuspected factors, such as purity; or uncontrolled factors, such as grain size, on the plastic properties of alloys. Nevertheless the following conclusions might be tentatively accepted: 1. Addition of solute elements invariably increases the yield strength, tensile strength, and hardness of the host element. 2. The rate of strain hardening, in general, increases with the concentration of the alloying element. 3. The strengthening effect in ternary alloys is the sum of the individual strengthening effects of the two solute elements as measured in their binary alloys. 4. The lattice strain is one factor that affects the strengthening of the alloy but it is not the only factor. 5. A second factor might be the difference in valence between the solute and solvent metals. All of the available evidence is in complete agreement with the first conclusion; the remaining conclusions, however, are not in agreement with all of the published data, but, in each case, the major weight of the existing evidence favors these deductions. Additional investigations will be required before most of these tentative conclusions can be accepted without reservation. In the following report an extensive investigation of the plastic properties of binary aluminum alloys is described. This work was undertaken in an attempt to shed more light on the general problem of solid solution hardening. Materials for Test: Aluminum was selected as the solvent metal for the present investigation on the effect of solute elements on the plastic properties of alloys. This choice was made for several reasons: (1) There appears to be little fundamental data in the published literature on the effect of solute elements on the properties of high-purity aluminum alloys. In view of the ever increasing economic importance of aluminum, such data would be of basic interest to the metallurgists concerned with the development of new aluminum alloys. (2) Aluminum is thought to be only partially ionized in the metallic state1&apos; and consequently it might provide more complex relationships of the mechanical properties with the concentrations of the solute elements than more simple fully ionized solvents would reveal. (3) The data on aluminum alloys will provide a broader basis for correlations between the mechanical properties of metals in general and the concentration and atomic properties of the solute elements than is now available. Some complications, however, attend the selection of aluminum: The solubility of the various elements in the alpha aluminum phase are quite restricted, and not always well known. Consequently, only dilute solid solutions are available for study. This, however, may be somewhat advantageous because the dilute solution laws presumably are simpler than those applying to concentrated solutions. In addition, strain-hardened pure aluminum is known to recover at atmospheric temperatures. Very likely its alloys exhibit slower recovery rates. Thus, the secondary factor of effect of alloying elements on recovery might complicate the data. Such compli-

Jan 1, 1951

By George S. Ansell, Thomas E. Davidson

It has been known for a considerable period of time that the ductility of even quite brittle materials can be enhanced if they are deformed under a superposed hydrostatic pressure of sufficient magnitude. The response of ductility to pressure, however, has been shown to vary considerably between materials. Prior work has shown that the effects of pressure upon the tensile ductility of Fe-C materials depend upon the amount, shape and distribution of the brittle cementite phase. In this current investigation, the effects of pressure upon the fracture mechanisms in a series of annealed and spheroidized Fe-C materials were examined. It was observed that the principal effect of pressure is to suppress void growth and coalescence, retard cleavage fracture and to enhance the ductility of cementite platelets in pearlite. Based upon the observed effects of pressure upon the fracture mechanisms, a proposed explanation for the enhancement in ductility by pressure and for the structure sensitivity of the phenomena is presented and discussed. THE effect of superposed pressure upon the tensile ductility of a variety of metals has been well documented.&apos;-&apos;&apos; Some of the results from several investigators are summarized in Fig. 1 where tensile ductility in terms of true strain to fracture (ef) is plotted as a function of the superposed pressure. As can be seen, a pressure of sufficient magnitude can significantly enhance the ductility of metals. However, Fig. 1 also demonstrates that the response of ductility to pressure and the form of the ductility-pressure relationship varies considerably between materials. Several explanations have been offered for the observed enhancement in ductility by a superposed pressure. Although no experimental evidence was provided, Bridgman13 and Bobrowsky10 proposed that the observed effect was due to the prevention or healing of microcracks or holes. Bulychev et a1.14 observed that cracks and voids in initially prestrained copper were healed in the necked region of a tensile specimen upon further straining while under a superposed pressure. Also, pugh5 observed that large cavities were suppressed in copper fractured in tension while under pressure. A second proposal has been forwarded by Beresnev et at al.6 This proposal is based upon the hypothesis that a material fails in a brittle manner because the normal tensile stress reaches a critical value before the shear stress is of sufficient magnitude to cause plastic flow. Since a superposed hydrostatic pressure will increase the ratio of shear to normal tensile stress, a sufficiently high hydrostatic pressure should favor plastic flow while retarding brittle fracture. Galli15 reported that a superposed pressure shifts the ductile-brittle transition temperature of molybdenum. This was explained based upon the reduction of the normal tensile stress by the superposed pressure. Pugh5 explained the occurrence of the observed pressure induced brittle-to-ductile transition in zinc in the same manner. Davidson et al.12 proposed an explanation for the enhancement of ductility by pressure based upon the effects of pressure upon the stress-state-sensitive stages of various fracture propagation mechanisms. Basically, they proposed that pressure will retard cleavage and intergranular fracture by counteracting the required normal tensile stress or will suppress void growth. They observed suppression of intergranular fracture and void growth in magnesium by pressure. Davidson and .Ansell16 reported ductility as a function of pressure for a series of annealed and spheroidized Fe-C alloys. Fig. 2, from this prior work, demonstrates that the effect of pressure upon ductility is structure sensitive in terms of the amount, shape and distribution of the brittle cementite phase. As shown in Fig. 2, in the absence of cementite or when the cementite is in isolated particle form (spheroidized), the ductility-pressure relationship is linear and the slope decreases with increasing carbon content. In the annealed carbon-bearing alloys wherein the cementite is in the form of closely spaced platelets (pearlite) or in the form of a continuous network along prior aus-tenite boundaries (1.1 pct C material), ductility as a function of pressure is nonlinear (polynomial relationship) in which the slope increases with increasing pressure. At the highest pressures studied (22.8 kbars), the slope of the curves for these materials tends to approach those for the spheroidized material of the same carbon content. In this current investigation the change in fracture mechanisms as a function of pressure for the materials shown in Fig. 2 has been examined. The possible connection between the observed effects of pressure upon the fracture mechanisms and the effect of pressure upon ductility is discussed.

Jan 1, 1970

By F. Weinberg

The relative concentration of 1" at grain boundaries in controlled orientation bicrystals has been examined by autoradiographic techniques, and by activity measurements of grain boundary surfaces exposed by preferential ,melting. The autoradio-graphs indicate that thallium is concentrated at grain boundaries in as-grown bicrystals, but not in zcell-annealed bicrystals. They also indicate that the solute concentration and the distribution on as-grown bicrystal surfaces are markedly different than that of the bulk material. The boundary surface measurements are in agreement with the autovadiographic evidence. On the basis of these measurements, as-grown bicrystals containing approximately 100 ppm of Tl, solidified at rates between 5 and 30 cm per hr and with tilt boundaries greater than 10 deg, exhibited grain boundary segregation equivalent to roughly 10 atomic planes of pure solute. Higher solute concentrations (equivalent to 140 atomic planes of pure solute) were obtained in bicrystals solidified slowly (0.6 cm per hr); slightly higher values were obtained in specimens containing a large angle nantilt boundary. Annealing for various times over a range of temperatures eliminated grain boundary segregation within the experimental uncertainty of the results (equivalent to 1 atomic Plane of pure thallium at the boundary). The results for the as-grown bicrystals can be qualitatively accounted for by assuming the presence of a groove on the solid-1iq;id interface, at the grain boundary. SOLUTE segregation at grain boundaries may be considered in two parts, namely, nonequilibrium segregation associated with the solidification process, and equilibrium segregation in fully annealed materials.&apos; There is much indirect evidence for nonequilibrium segregation, based on preferential etching at grain boundaries and the mechanical properties of as-cast alloys. In addition, some direct observations have been reported in which radioactive tracers were used as solute additions and segregation detected at the grain boundaries by autoradiographic techniques. However, there is little detailed quantitative data on solute concentrations related to grain boundaries, particularly for different freezing conditions and grain boundary configurations. Equilibrium segregation at grain boundaries has been considered both theoretically and experimentally. cean&apos; has made an estimate of the maximum equilibrium solute concentration that might be expected at a grain boundary, based on the lattice distortions in the boundary region. He arrived at a concentration which was equivalent t a monatomic layer of pure solute. A similar value, based on thermodynamic arguments, was calculated by Cahn and Hilliard for the segregation of phosphorus in iron. Experimentally, much higher values of solute concentration at grain boundaries have been reported recently by both Inman and iler&apos; for phosphorus in iron, and Ainslie et 1.&apos; for sulfur in iron. They observed concentrations equivalent to as much as 20 to 100 atomic layers of pure solute at the grain boundaries. However, in both cases it was shown that the observed segregation was not due solely to equilibrium segregation at the grain boundary. In the former case, precipitation effectss due to trace impurities in the material were believed to account for the large amount of solute present at the grain boundary. In the latter case it was shown that a high density of dislocations in the boundary region could provide a large number of additional sites for solute atoms, other than at the grain boundary. Thomas and chalmera have reported on the equilibrium segregation of po210 in grain boundaries of Pb-5 pct Bi alloys. Using autoradiographic techniques, they observed a concentration of polonium along the boundary trace on the surface of annealed bicrystal specimens grown from the melt. The concentration only appeared after annealing, and varied with boundary angle, increasing as the boundary angle increased. Their conclusions have been questioned by Ward," who pointed out that the segregation they observed along the boundary trace was much too wide to be compatible with the usual concepts of the thickness of a grain boundary of several lattice spacings. Also, Maroun et al.,l1 with specimens similar to those of Thomas and Chalmers, found that segregation could only be detected on the specimen surface, suggesting that Thomas and Chalmers&apos; results were associated with an oxidation effect of polonium, and not equilibrium segregation. Thomas and Chalmers replied12 that they did observed segregation at the grain boundary in the bulk material and suggested further experiments were necessary to resolve the difference. The purpose of the present investigation was to examine both nonequilibrium and equilibrium grain boundary segregation in melt grown bicrystal specimens as a function of boundary angle, growth rate, and solute concentration, and to de-

Jan 1, 1963