Search Documents

By Fun-Den Wang

An open pit rock structure usually contains geological planes of weakness. They are formed by joints, faults, bedding planes, fractures, and cleavages. Rock slope failures often occur in the form of sliding of rock blocks along a plane or several planes. Such a rock block has three- dimensional geometry, and consequently a vector method of analysis has been found useful in evaluating its stabi1ity.l-3 Rock blocks of a tetrahedral shape with one free surface have been analyzed by Londe.3 Rock blocks formed by sets of parallel joints have been analyzed by Wittke.1,2 The present chapter presents the analysis of rock blocks formed by planes of weakness of arbitrary orientation, and of three-dimensional geometry. A plane of weakness is represented by its dip and strike in vector form and is reduced to the form of a linear equation. The geometry of the rock block is defined by solving the linear equations. The geometric characteristics of a rock block are based on triangles and tetrahedrons. By this treatment, the three-dimensional geometry is simplified and the number of calculations of forces and moments is reduced. Methods of finding the geometric characteristics are presented, along with equations for calculating the resultant forces and moments and the factor of safety. BASIC ASSUMPTIONS The following assumptions are used : The solid part of the rock mass is much stronger than the rock mass at the plane of weakness and the rock mass will only fail along planes of weakness.

Jan 1, 1972

By Tracy Jarrett

In 14-karat gold alloys, as in 10-karat gold alloys,3 the addition of such metals as zinc, nickel, copper and silver produces a wide range of physical and chemical proper-ties such as color, hardness, corrosion resist-ance and melting points. These important factors made gold alloys desirable in the optical work and for jewelry. In 14-karat gold alloys, as well as in 10-karat or 12-karat, it is possible to have two golds of the same color, one of which will corrode more than the other, although it may be harder. Some of these alloys have been investigated by F. E. Carter,1 E. M. Wise,5 and L. Sterner Rainer.4 In this group of alloys the gold content of 58.3 per cent (14-karat) was held constant, while the copper varied from 36 to 24 per cent. The balance of the alloy consisted of one, two, or three of the metals silver, zinc, and nickel. All the alloys were melted in an induction furnace and cast into an ingot that meas-ured 3 by 1/4 by 3/4 in. The method of determining the melting points, color deter-minations and acid test have been discussed in previous papers by the author.2,3 It is necessary to use small test bars (Fig. r). The tensile bars were annealed at 1300°F. for 20 min. and then air-cooled. There being a very marked drop when the yield point was reached, "the drop of the beam" method was used in determining the yield point.

Jan 1, 1940

By H. A. Kursell

IN pre-war days, the mining industry of Russia occupied in the industrial life of the Empire a place of ever increasing importance. The peak of produc-tion was reached in 1913 and 1914, the years of greatest prosperity, and a rapid growth of the mineral industry seemed assured, especially as regards base-metal mining. Exceptions were the gold production, for which a gradual decline was anticipated, and the platinum out-put which was expected to remain steady. A greater productivity of labor, corresponding to better working facilities was noticeable, and the economic status of the working classes was constantly improving. The tremendous strain on Russia's economic life caused by the World War did not materially alter the prospects of the mineral industry and the fundamental changes began only with the revolution in the spring of 1917. Their scope and character are illustrated by the figures in Table 1 which compare, for the parts of the Russian Empire under Soviet (R. S. F. S. R.) control, the average mineral production of 1913 and 1914 with that of 1920, 1921 and 1922, as supplied by bolshevik sources.1The latter three years in Russia's history were characterized by the firm establishment in power of the Communist party as a new ruling caste. Silver, lead, zinc, tin, nickel, tungsten, barite, etc., were either produced in negligible quantities, or not at all. However, before the revolution the development of several argentiferous lead-zinc deposits in western Siberia had reached a stage which seemed to assure an appreciable output of the white metals for the near future.

Jan 7, 1923

By Arnulf Muan

PHASE relations in three isothermal sections (l000°, 1100°, 1200°C) of the system Ag-Fe-Pd have been determined as part of a program to develop improved crucible materials for containing low-melting iron silicates at low oxygen potentials. The following experimental method was used: Two- to 3- g samples of each of forty different alloys within the system Ag-Fe-Pd were made up from metals of 99.9 pct purity. The mixed metal powders were contained in a 1-cc crucible of dense recrystal-lized alumina and heated in a protective atmosphere (90 vol pct A, 10 vol pct H2), first to complete melting for approximately 30 min and subsequently at the desired equilibration temperature (1000°, 1100°, or 1200°C) for approximately 24 hr. The samples were then quenched rapidly to room temperature and examined metallographically as well as by X-ray techniques. Unit cell dimensions were compared with standards obtained by study of one-phase alloys of known compositions. The results are summarized in diagrams (a), (b), and (c) shown in Fig. 1. Heavy solid curves outline areas comprising compositions of mixtures consisting of the phases labeled for each area. Mixtures in which liquid is the only condensed phase present are confined to very narrow areas adjacent to the Ag-Pd join at high silver contents. An enlarged, distorted picture of the phase relations prevailing in these areas is shown in the upper-left circular insert. Particular attention is directed toward the misci-bility gap which occupies major parts of the composi-

Jan 1, 1962

THE following employment items are made available to AIME members on a nonprofit basis by the Engineering Societies Personnel Service, Inc , operating in cooperation with the Four Founder Societies Local offices of the Personnel Service are at 8 W 40th St , New York 18, 100 Farnsworth Ave, Detroit, 57 Post St , San Francisco, 84 E Randolph St , Chicago 1 Applicants should address all mail to the proper key numbers in care of the New York office and include 6c in stomps for forwarding and returning application The applicant agrees, if placed in a position by means of the Service, to pay the placement fee listed by the Service AIME members may secure a weekly bulletin of positions available for $3 50 a quarter, $12 a year MEN AVAILABLE Executive Engineer, 37, married, 3 children Now Resident Manager nonmetallic underground mine and processing plant Management and operational experience in gold, copper, zinc, limestone and lime products manufacture Mine plant design and construction, underground mines and quarries Excellent references Currently employed but available reasonable notice Prefer U S M-687-426-E-5-San Francisco Metallurgical Engineer, 29, married, one child, B S Metallurgical Engineering Five years' practical experience in milling and laboratory research Available thirty days Prefer West or Southwest U S A M-689¬522-E-1-San Francisco Experienced Mining Engineer, university graduate, 40, married Twenty years' experience all phases metal mining, past 13 years as manager, excellent cost and safety record Available short notice Best references and complete professional record available upon request M-690

Jan 1, 1952

By Joseph Pogue

THE, prices of crude petroleum and its derivatives have shown an upward trend from 1915 to 1920, and a downward trend from 1920 to 1923, see Table 1. Over the former period, oil prices were dominated by the rapidly increasing demands and inflation incident to the war and its aftermath, while over the latter period oil prices were influenced at the outset by deflation and then by the conditions of overproduction that have characterized the past three years. The purpose of this paper is to analyze the broader features of the more recent price movements in the petroleum industry and to relate these features to basic economic conditions in the industry. INDEX NUMBERS OF OIL PRICES The analysis and comparison of price movements may be facilitated by converting actual prices into relative prices, or index numbers, with 1913 taken as a base of 100. In this way, the various price groups are expressed as percentages of the 1913 prices and may thus be readily compared with one another or with the average prices of other commodities similarly expressed. Table 1 gives the index numbers representing the average prices of crude petroleum, gasoline, kerosene, fuel oil, lubricating oils, and all commodities. The last named is the index of all commodities as published by the U. S. Bureau of Labor Statistics and .is widely accepted .as the official measure of the general price level. The index numbers of oil prices were calculated by the writer from weekly quotations published in trade journals.

Jan 3, 1924

By Niels Hansen

Dispersion-strengthened sintered aluminum products are normally manufactured from surface-oxidized aluminum powder, SAP,' or from atomized aluminum powder.' The powder-blending technique consisting in mechanical mixing of the constituents has been used in the manufacture of numerous dispersion-strengthening alloys, but has never been successfully applied to aluminum alloys. This technique may, however, be applicable if it is possible to produce an unagglomerated mixture of the constituents in the form of fine powders, and the present study was initiated to test this assumption in the aluminum/aluminum oxide system.3 Table I lists the two grades of aluminum powder and the aluminum oxide powder used in the manufacture of the alloys. MD 105 A is an aluminum powder with an average grain size less than 5 IJ., which is isolated from the MD 105 powder by centrifugal separation in cyclohexanol. The aluminum powders and the aluminum oxide were blended in a high-speed blender and then subjected to cold compaction and hot compaction at 550" to 600°C. Subsequently the compacts were hot-extruded with an extrusion ratio of 15 to 1. The alloys were evaluated by tensile testing at room temperature and at 400°C, microscopic examination, and heat treatment at 500°C followed by tensile testing at room temperature. For the purpose of comparison, a commercial SAP quality supplied by Swiss Aluminium Ltd. was tested in the same manner. The tensile data at room temperature and at 400°C are plotted in Figs. 1, 2, and 3 as a function of the weight percent of oxide. The oxide content

Jan 1, 1964

By Kendall E. Born

Production of crude oil in Tennessee during 5945 was slightly more than 6000 bbl., the lowest figure since 1916. Approximately 5500 bbl. was produced from the "Mississippi lime" in Scott and Morgan Counties. The remainder was from two wells each in Clay and Fentress Counties. Thirty million cubic feet of gas was marketed off the lease in Morgan County and about 10 million cubic feet was produced in the Jamestown field in Fentress County. The production of oil by counties is shown in Table 1.

Jan 1, 1946

By J. G. Davis, P. C. Thakur

Hazardous methane gas in coal mining is receiving increased attention due to the increased US demand for coal which has resulted in the exploitation of deeper seams and the utilization of more productive equipment. Problems posed by methane emission has the Mining Research Division of Continental Oil Co. (Conoco) accelerating efforts that began in the early 1950's with Consolidation Coal Co. (Consol).1 The program's focus is on finding new techniques for degasification of virgin areas as well as control of methane in gob areas.

Jan 10, 1977

By N. Arbiter, C. C. Harris

Analysis of ball and pulp flow in ball mills indicates that three factors may become critical with increasing mill diameters: ball size, fraction critical speed, and average pulp flow velocities. Ball diameters may need to be decreased and fraction critical speeds increased with ores which show decreased breakage rate coefficients above 1.2 mm (14 mesh). With 5.5-m (18 ft) and larger mills at higher circulating loads, pulp flow velocities may become capacity limiting and also may limit increases in ball mill diameters.

Jan 1, 1985

By F. Galasso, A. Paton

ThE recent emphasis on producing boron fibers by reacting boron trichloride and hydrogen on a hot tungsten wire has brought about a renewed interest in the tungsten boride phase diagram. The reaction of the boron with the tungsten core results in the formation of 6 WB, W2B5, and another tungsten boride phase, which was suspected of being the WB4 phase reported by Chrbtien and Helgorsky.1 While the powder-diffraction data for the boride in the fiber and those reported

Jan 1, 1967

By J. H. Rose

The arrangement of the reverberatory furnace and the two waste-heat boilers at the Magma Copper Company's smelter at Superior, Ariz., is shown in Fig. 1. The inside dimensions of the furnace at the slag line are: length, 96 ft.; width, 22 ft. The boilers are Erie City vertical type with a rated capacity of 700 hp. The 3-in. boiler tubes are arranged in two banks with a vertical baffle between. The banks are 30 tubes wide by 9 tubes deep—a total of 540 tubes.

Jan 1, 1934

By J. W. Still

CIRCULAR steel sets have proved to be more economical for supporting slusher drifts in the block-caving mining used by the Miami Copper Co., at Miami, Ariz. The first steel sets were installed in July 1950, and up to July 1, 1951, about 474 sets (approximately 1896 ft of drift) were placed; the bulk of this work was done in the latter six months. All of the places selected for the steel were in heavy ground. Based on this experience the following definite conclusions can be drawn:

Jan 11, 1951

By John V. Beall

When a mine has ore averaging 5% lead, 7% zinc, 0.60% copper, 1/4 oz gold, and 6 oz of silver, adequate reserves, power and water, easy access to market, and is situated in beautiful natural surroundings with the advantages of a big city within a few hours drive, there is little left to be desired. Such a mine is the Mayflower mine of the New Park Mining Co. situated 30 miles from Salt Lake City in the Wasatch Mountains near Keetley, Utah.

Jan 1, 1949

State Mine Experiment Station, College of Engineering, University of Alabama, University, Ala Copies of two bulletins issued by the Mine Experiment Station may be had by writing to the Director of the School of Mmes at the above address: Bulletin 1, Coal losses in Alabama, 2, A specific gravity study of Alabama coals The Cooperative work of the Mine Experiment Station with the Southern Experiment Station of the U S Bureau of Mmes is covered by Bulletins of the U S Bureau of Mines

Jan 1, 1933

In accordance with the provision of the Constitution, notice is here given to all Members, Associates, and Junior Members, that the clues of the year 1918 will be payable on Jan. 1. 191.8, at the office of the Secretary. The dues for Members and Associates are $12 per year and the sum of 83 additional is asked of those Members and Associates who desire to have the three volumes bound in the Institute's standard half morocco binding. The dues of Junior Members are $5 per year.

Jan 12, 1917

In accordance with the provision of the Constitution, notice is here given to all Members, Associates, and Junior Associates, that the dues of the year 1919 will be payable on Jan. 1, 1919, at the office of the Secretary. The clues for Members and Associates are $12 per year and the sum of. $2 additional is asked of those Members and Associates who desire to 'have the two volumes bound in the Institute's standard binding. The clues of Junior Associates are $5 per year.

Jan 12, 1918

In accordance with the provision of the Constitution, notice is here given to all Members, Associates, and Junior Members, that the dues of the year 1918 will be payable on Jan. 1, 1918, at the office of the Secretary. The dues for Members and Associates are $12 per year and the sum of $3 additional is asked of those Members and Associates who desire to have the three volumes bound in the Institute's standard half-morocco binding. The dues of Junior Members are $5 per year.

Jan 1, 1918

By Terry G. Richard, Vernal H. Kenner, Sunder H. Advani

This paper presents and discusses the results of thirty-one fracture toughness tests on Pennsylvanian Age Clay Shale. Two different orientations for this anisotropic material were studied and two series of tests were conducted, namely, 1. a test series to determine the effect of moisture content on fracture toughness, and 2. a test series to study mixed mode fracture. Increased absorbed moisture is found to reduce fracture toughness. Several analyses of mixed mode failure are found to give varying non-conservative predictions of failure stress intensity level.

Jan 1, 1982

By R. H. Richman, II Conard G. P.

AS part of a study of deformation twinning in bcc crystals, solid solutions of beryllium in iron have been found to twin profusely when strained slowly at room temperature. This note reports some crystal-lographic aspects of the operative mechanical twin modes in a quenched Fe-5 wt pct Be alloy. After melting twice under a partial pressure of helium, the alloy was homogenized, cut into pieces 7 to 10 mm on an edge, solution treated at 1130°C,1 and quenched. Debye-Scherrer patterns confirmed

Jan 1, 1963