Search Documents

By Wood P. D, Pettifer G. R

In the upper coal surface in the Latrobe Valley, craters known locally as fireholes have developed due to prehistoric coal fires. They can be several hundred metres across and up to fifty metres deep, and are now filled with overburden materials varying from hard baked clays to very soft lacustrine clays. In addition to reducing coal reserves, continuous mining operations are seriously affected by fireholes. Large undulations in the upper coal surface result in a mixture of coal and overburden on the upper mining levels. The very soft lacustrine clays are unstable in the mine batters and the overburden dump, are difficult to handle on the bucket wheel excavator/conveyer system, and have insufficient bearing capacity for the large bucket wheel excavators. Early identification is essen- tial and both drilling and dynamic core penetrometer have been exten- sively used. However, this has not proved adequate in locating and defining the extent of all fireholes, due largely to their irregular shape. To overcome this a range of geophysical techniques has been trialled with very promising results. A trial area has been covered on a twenty metre grid using gravity and Geonics EM34 conductivity measurements and the same area has been covered at a closer spacing with high resolution magnetics. Image processing of contoured magnetic, EM34 conductivity and residual gravity data has resulted in very good correlation with drilling data.

Jan 1, 1989

By Loo C. E

Thirty two polyacrylamide flocculant samples were selected from the wide range offered to the Australian coal industry. An extensive test program was conducted to consider the properties of the flocculants, the substrates, the process conditions and the water chemistry encountered in coal preparation plants. The study indicated that flocculants with molecular weights of 12 to 14 million and degree of hydrolysis around 40% gave the best "average" performance over a wide range of process conditions. The pick-up and filtration of fine coal was demonstrated on a pilot scale to be a critical function of flocculant properties. This study also showed that the agitation intensity during flocculation was a critical parameter in determining the settling rate of the slurry and the clarity of the resulting supernatant. An electronic meter to measure agitation intensity was designed, constructed and tested to demonstrate how, for the first time, laboratory results can be implemented in operating plants.

Jan 1, 1989

By de Vries D, Wilson EG, Henderson GAM, Carter EK

Canberra is a planned city in which the natural environment, rather than existing development and land tenure, has until recent times at least, imposed the major constraints to development. Even redevelopment poses fewer problems than for most cities. Geological conditions have, therefore, played a significant role in determining its shape and layout. The Canberra experience has relevance for major new mining and engineering projects. The role of engineering geologists and geophysicists in Canberra's development is described, and the problems arising from the geological environment are illustrated by several case histories. Four aspects are addressed: pre-development urban geology; major engineering projects; resources evaluation, including groundwater; and post-development problem-solving. The Australian Capital Territory lies within the Palaeozoic Lachlan Fold Belt. Within the ACT the belt is composed of folded and faulted metasiltstones, metasandstones and acid volcanics, intruded by a major granitic pluton. Some limestone lenses occur. The region has been part of a land mass since Late Devonian times and landscape evolution has been very complex. Geological features of special geotechnical significance include deep but variable weathering, with slight to moderate weathering along faults to at least 70 metres depth in places, and consequential foundation problems; close jointing; weathered limestone lenses with solution cavities containing clay and water; confined aquifers containing artesian water in scree deposits flanking hills; the presence of pyrite; and poor quality and low volumes of groundwater.

Jan 1, 1986

By Raymond G. F

Geostatistics - a tool used by geologists and mine planning engineers to estimate grades and rapidly evaluate alternative mining strategies has reached an advanced stage of development for the silver-lead-zinc orebodies at Isa and Hilton Mines. Geostatistics has been used for over a decade in the massive copper orebodies but the stratiform lead-zinc orebodies are much more complex and provided a completely different set of challenges. Recent increases in computer processing speed and power provided by the Integrated Mine Planning System (IMPS) has aided the development of the geostatistics package. Also the formation of a project team and the subsequent in-house development which has drawn together the expertise of geologists, engineers and system analysts has contributed significantly to the success of the project.The most important feature of any approach to modelling the lead-zinc orebodies is that the kriging search must consider estimate and sample points according to their positions relative to bedding surfaces. By transforming co-ordinates as perpendicular offsets from a plane representing the local strike and dip, it is possible to elongate the ellipsoidal influence to parallel bedding. By interactively modelling surfaces using CAD facilities and then specifying these surfaces as 'hard' or 'soft' boundaries, the geologist has complete control over the kriging process.

Jan 1, 1993

By Demin SS

Slow seismotectonic movements along the in-clined deep fault zone under the compressional horizontal stresses are supposed to be the prin-cipal mechanism controlling the structure and processes in the active ocean margins. Within the scope of the plane strain problem a simple 2-D geomechanical model for the evolution of an island arc system is investigated. We consider a homogeneous elastic half-plane with a shea-ring surface crack. The key element of the model is viscous interaction between the crack sides, the viscisity varying with depth. The model dif-fers from the classical steady-state mode of subduction by nonstationary creep processes on deep faults and by possibly cyclical development of the transition zone.A numerical modeling of the stress-strain state within the island arc system through time was carried out using a semianalytical approach. The results of simulation are in good agreement with geological, geophysical, and seismological data.

Jan 1, 1990

By Zhen Y. Y, Cook A, Jell J. S, Fleming P. J G

Remapping of the Burdekin Basin has resulted in subdivision of the three interfingering basin-wide megafacies previously recognised in the Early to Middle Devonian Fanning River Group. Eleven carbonate and siliciclastic facies are now identified within the three megafacies, representing coastal plain, shoreline, nearshore, and shallow marine shelf depositional environments. The facies reflect two phases of a major transgression. An initial phase, in the Early Devonian, was confined to the far north of the basin, whereas a second, main phase, resulted in the encroachment of the sea from the east or southeast in the Middle Devonian.The proposed depositional model begins with the drowning of a coastal plain and the transgression of shoreline and nearshore facies between granitic and metamorphic headlands and/or islands. This was followed by the deposition of a patch reef and fringing reef complex including stromatoporoid and coral bioherms, biostromes, and oncolitic, crinoidal, and brachiopod-dominated banks/shoals, together with foreslopes and submarine channels, carbonate rubble deposits and terrigenous sediments. Sedimentation during the peak of the transgression was dominated by sheltered carbonate shelf facies, the maximum, flooding surface being recognisable across most of the Burdekin Basin. Progradation of muddy and sandy nearshore bay and shoreline facies soon followed, terminating carbonate deposition.

Jan 1, 1990

By Laird CH

Large quantities of brown coal are excava ted from open cut mines in the Latrobe Valley to fire the base load thermal power stations of the Victorian Electricity System. Most of the coal is removed using bucketwheel excavators which have been modified or specially designed for the conditions encountered. The actual digging efficiency of the bucketwheel excavator is strongly influenced by such factors as wheel speed, slewing speed and tooth design and arrangement. The coal deposit, although not difficult to work, is not uniform and the operation of the machine is influenced by the stability re- quirements of the excavation face.

Jan 1, 1978

By Peck J. P, Kennedy D

Drill performance monitoring studies were recently completed at the Fording River mine, British Columbia. Microprocessor-based instrumen- tation and data analysis techniques were developed with the objective to improve short and long term mine planning. Data analysis permitted the identification of thicknesses and interfaces between soft/hard zones at depth based upon the recorded responses of the drill. Data clearly con- trast the soft coal seams and harder waste rock units based on variations in recorded drill rotary speed and torque, hydraulic downpressure, bail- ing air pressure and instantaneous rate of penetration. These parameters were monitored and recorded at 10 cm sampling intervals. Processed drill data was correlated with gamma logs, an existing means for locating coal seams and distinguishing between waste units. Current development of a pattern recognition module aims towards automated interpretation of drill data, identifying micro-and macro-geological and geomechanical rock mass characteristics. Delay between acquiring, processing and interpret- ing the drill data for practical use by mine personnel should be minimized. Integration of this technology with the mine's current main-frame based Mine Engineering Application System software will enable more accurate and timely annlication of the nrocessed drill data.

Jan 1, 1989

General design of pillars to ensure a continuing roof support during ex- traction is discussed. Practical problems associated with pillar extraction are Outlined.

Jan 1, 1974

During late 1953 and early 1954, tests were carried out in Sydney metropolitan brickpits in order to determine if some improvement might not be effected in the personal shock, fly rock and possible ground displacement accompanying daily blasting occurrences in the numerous quarrying activities of the metropolitan area. As a result of this preliminary work (Reid, 1954), the Department of Mines decided to further investigate the problem with a view to placing this type of blasting on a sound economical and safe basis for both operator and nearby residents alike. To assist in the work, a Cambridge Universal vibrograph was acquired.Human safety was the first consideration followed by property damage to homes and factories in the extractive areas. Although most of the actual field work has been confined to the Sydney metropolitan area and in particular to the large clay-shale quarries, many cities and country towns have blasting problems associated with the extractive industries, engineering projects both above and below ground level, and in building excavations to which the results may apply.The following figures illustrate how much activity of this type is located around cities and towns:Sydney Metropolitan Area:

Jan 1, 1958

By D K. Miller, L W. Armstrong

In April 2006, Orica Quarry Services undertook an investigation to determine the likely vibration and frequency response of three water storage tanks to quarry blasting, immediately adjacent to the tanks. Of the three tanks that were studied, two are relatively tall with a æwineglassÆ shape; one is constructed of steel (4 ML storage capacity) while the other is constructed of concrete (2 ML storage capacity). The third is a ground-embedded concrete tank that is relatively squat and broad in shape (38 ML storage capacity). A vibration limit of 25 mm/s and an acceleration limit of 0.16 g were imposed on the tanks. However, this report shows that this acceleration limit, whilst having relevance to low frequency earthquake motions, is quite inappropriate for the high frequency blast vibrations that are typical in a quarry blasting environment. The investigation involved firing 11 single blastholes of known charge weights and distances from the tanks, and measuring the tank vibration response using blast monitors placed on and around each tank. Analysis of the data collected from the cement tanks showed resonant responses over a broad range of frequencies, with dominant and lesser responses in vertical and lateral motion recorded at 9.8 Hz, 12 Hz, 16.8 Hz, 17 Hz, 31.3 Hz and 38.1 Hz. Unfortunately, most of the data collected on the steel tank was corrupted by noise due to electrical sources and/or mechanical sources such as the water agitator inside the tank. Advanced Monte Carlo vibration models were then constructed using the single blasthole information. Knowing the resonant frequencies enabled the modelling of electronic delay sequences for the reduction of resonant vibrations. Ultimately programmable and accurate electronic delay detonators were deemed essential to allow blasting in relatively close proximity to the tanks while avoiding resonant frequencies. Three blast designs were modelled, ranging in maximum instantaneous charge (MIC) from 4 kg to 22 kg, and 60 holes to 160 holes. The modelling showed that two of the designs (using small charge weights) could be used no closer than 71 m from the storage tanks. This is based on a 90 per cent confidence level of achieving vibration levels within the 0.16 g acceleration limit, even though the velocity levels predicted to be generated at this distance were significantly less than the 25 mm/s limit. The third design incorporated larger charge weights and could be used for blasting at distances no closer than 220 m from the tanks. The present work, conducted in an operating quarry, demonstrates the usefulness of Monte Carlo waveform superposition techniques for the control and reduction of ground vibration (either velocity or acceleration) under restrictive environmental constraints. However, a discussion is also presented to demonstrate that it is somewhat restrictive to impose an acceleration limit based on the motion produced by low frequency earthquakes rather than the motion produced by high frequency blast vibrations.

Jan 1, 2007

Grey River Gold Mining Ltd commenced dredging alluvial flats in the Grey River Valley in 1989.Previous drilling indicated over 100 million cubic metres of gravels with some 90% of the gold in the bottom 7 metres.The dredge built by Rahco, Spokane, was innovative in a number of aspects but particularly in the fact that a separate ladder with a cutter and pump was used to strip the overburden and a bucketline to mine the gold bearing wash below.Metallurgical studies and exploration were initiated when the project commenced; Leasing and environmental considerations were investigated and action taken.While progress is being made, the operation at this stage is not meeting required production and performance. Main problems have been with the stripping system and wear.

Jan 1, 1990

Goodenough and Fergusson Islands, in eastern PapuaNew Guinea, lie in an area of crustal extension on the western end of the Woodlark Basin seafloor spreading system. The islands are made up of a number of mountainous domes of complexely deformed basement, and these are intruded by large bodies of granodiorite. The domes are bounded by curved shear zones and faults dipping outwards at angles of around 25 to 45¦. The cores of the domes contain lower crustal rocks of eclogite and granulite facies, these rocks have undergone retrograde metamorphism in the outer sheared zones. Movement indicators on the shear zones indicate a complex moverm.-It geometry which does not fit the models proposed by earlier workers. These dome-like structures are similar to the metamorphic core complexes of the western United States Cordilleran region, however there are a number of aspects which do not fit with the models proposed for the development of metamorphic core complexes. Uplift of the metamorphic basement probably resulted from a combination of forces associated with the extension of the crust and the intrusion and emplacement of granodiorite plutons.

Jan 1, 1990

By A G. Grice

Surface disposal of mining processing wastes is usually perceived as an undesirable consequence of meeting societyÆs needs for metals and minerals. Environmental disasters associated with the discharge or storage of such wastes, though infrequent, can have very damaging consequences for the environment and the industry. Reducing or eliminating the potential for such events may be achieved by placing some or all of these processing wastes back into the voids created by the mining operations. Processing operations may limit or enhance the opportunities for using tailings and other waste products as a backfill material. Backfilling is a truly multi-disciplinary process and requires the informed involvement of mining, metallurgical, engineering and environmental specialists. This paper describes the range of fill types currently being used in Australian mines, particularly those utilising processing wastes as constituents. It focuses on how processing operations can affect the suitability of these materials for the various types of fill, the resulting fill properties, fill performance and costs.

Jan 1, 2002

By B Lindqui, M V. Knyazev, L S. Tsemekhman

Gipronickel Institute JS that is a Research and Development Centre affiliated to the worldclass Norilsk Nickel Mining and Metallurgical Company, and Outokumpu Technologies AB (Boliden Contech AB) have jointly developed the reconstruction project of Pechenganickel metallurgical operations using a two-zone Vanyukov furnace. The international expert group appointed by the Nordic Investment Bank has examined the project. The project financing should be partly executed by the Norway government. Current annual rate of sulfur dioxide emissions is 100 000 t. The aim of the project is to reduce it to 12 000 tpy. Pechenganickel Combine is owned by MMC Norilsk Nickel. Currently it produces nickel high-grade matte from sulfide copper-nickel concentrate with up to ten per cent MgO content. The existing production is in accordance with the following flow sheet: agglomeration û electric furnace smelting with matte production û converting in horizontal converters. Annual production capacity is about 36 000 t of nickel in high-grade matte. Converter gases report to sulfuric acid production. The principal results of studies on high magnesia materials smelting in two-zone Vanyukov furnace, engineering solutions, and technical and economical parameters are offered.

Jan 1, 2004

The following is based on two examples of emission control with coal fired power stations as practised in Germany at Heilbronn Block 7 power station and the Rheinbraun coal combined power station with integrated high-temperature Winkler system (HTW). Heilbronn Block 7 demonstrates the successful emission control of sulphur and nitrogen oxides and the (HTW) system the reduction of the specific carbon dioxide emission. Both were sparked off by legislation which demanded certain emission control standards. Since the early eighties environment protection has been a matter of heated public debate in the European Community. A recent survey in Germany showed unemployment as being the only subject matter more frequently in the minds of people than environment protection. A new kind of forest devastation in areas away from industry has caused investigations by several government departments and private enterprise. Because of lack of conclusive evidence so far, the principle of PRECAUTION has replaced the CONCLUSIVE evidence as a base for new legislation concerning the environment. The new legislative standards for nitrogen oxide emissions in Germany for example have reduced NOx emissions of power stations from 1000 mg NOx per cubic metre of flue gas in the beginning of 1983 to 200 mg NOx per cubic metre of flue gas in April 1984. These new standards were enshrined in legislation when research provided some evidence linking nitrogen oxide emissions through photo-chemical reactions with forest devastation. Thirty European countries signed a treaty in 1983 expressing their concern about air pollution and their willingness to co-operate with each other in controlling large scale emissions.

Jan 1, 1991

By Fuller T

This paper introduces the technology used in laser surveying systems, and the development of a reflectorless one-man total station. These systems are being used for applications such as blast pattern surveys, face profiling, muckpile surveys and the general survey of inaccessible areas. Black Diamond Solutions is continuing to assess new technology and develop integrated systems for applications in the mining industry.

Jan 1, 1995

By Johnston RRM

There have been many published mathematical models that, to varying degrees of sophistication, attempt to describe dynamic thickener behaviour. CSIRO has undertaken to develop a model under industry sponsorship. Recently developed instruments such as the floc density analyser and natural gamma-ray gauge have enabled new data to be collected from plant thickeners for model validation and development. The principles behind the use of the natural gamma-ray gauge are described and the possibilities for its use as a control instrument in the bed have been examined. A simple nomograph illustrates how the gamma-ray gauge data can be used to predict steady state underflow consistency and bed Position.

Jan 1, 1991

By Rogers M, Sullivan B

Golden Crown Mine is a narrow vein gold mine producing 75000 tpa. Production has been predominantly by shrink stoping using hand held machine and airleg. Bogging from these stopes is done with Toro 150 LHD units.Previously the standard development method consisted of developing a sill drive, a footwall drive and millholes every 7 m. This meant that for every metre of ore development, 2 m of waste development was required.

Jan 1, 1993

By Szwedzicki T

Uniaxial testing was performed on model pillars to determine the effect of width to height ratio on pillar and surrounding rock mass stability. Samples were modelled in a shape similar to that of dumbbell weights, with the centre representing

Jan 1, 1994