Search Documents

Authorisation No.66 (to Prospect) was allocated to R.W. Miller & Co. Pty. Ltd. on 1st November, 1976. Exploration has brought coal reserves to measured status in the Jerry's Plains sub-group which are about 550m. thick. The immediately lower Vane Sub-group, about 200m. thick, includes about 20 seams. The total measured and indicated reserves of the two sub-groups based on the criteria adopted by the company amount to 1362 million tonnes in situ. This very large resource is subject to very many mining constraints both physical and economic which limit the saleable reserves under present conditions to about 120 million tonnes. The results of the calculation of reserves after exploration is complete in a deep multiple seam situation is dependent upon the criteria used to include or exclude seams in the reserves. These criteria are state- ments of the miner's expectations of the market, mining and coal preparation technology, local and national politics and the law as it may be applied in the future.

Jan 1, 1979

THE auriferous sulphide ores of the eastern end of Gippsland, and notably of the Cassilis and lVIitta districts, are amongst the most complex and refractory in Victoria-perhaps in Australia. The minerals occurring in these ores are pyrite, arseno-pyrite, zincblende, galena, and (in smaller amounts) some of the copper, sulphides, as chalcopyrite and covellite; and some of the antimonial minerals, notably stibnite and jamiesonite. In the oxidized portions of the lodes, the oxidized lead and iron minerals, and small amounts of the hydrated arseriiate of iron, are found.In the Cassilis mine, near Omeo, copper is present usually in quantities of under 1 %. The magnetic sulphide of iron is of fairly common occurrence. In, the upper levels of the Cassilis mine tin was usually present, the amount going up to 3% in some samples of concentrates. These minerals occur sometimes banded, but usually as an intimate mixture-pyrite and arseno-pyrite predominating. The gangue is usually quartz (blackened by enclosed particles of sulphides). Calcite, magnesium silicate and felspar are also present in varying amounts.

Jan 1, 1911

Average annual growth in consumption of primary energy in Australia over the past ten years has been 5.5% compared to a world average of 4.1%. Over the next ten years growth rate is expected to increase to 6% per annum due largely to the rapid development in the mineral processing industry. By the end of the 1970's natural gas is expected to supply more than 9% of Australia's, primary energy market. Coal will supply 40% and petroleum products 47%. Nuclear energy will make its appearance but-will only make a small contribution in the period. Australia has adequate reserves of natural gas and coal to supply its needs in the 1970's and beyond. However the newly developed reserves of crude, while supplying 60-70% of requirements-in the initial years; will need regular and sizable additions if they are to .keep pace with the expanding consumption. For Australia to become self sufficient in the period 1970-1990 it is estimated *that new discoveries-will need to approximate. ten times the volume of recoverable reserves found in Australia to date. .

Jan 1, 1970

By Forssberg E

This paper presents the experimental results on the effects of slurry Theology on ultra-fine grinding by a stirred ball mill. The amount of dispersant, slurry density and the particle size were selected as the parameters. The viscosity of dolomite-water slurry was measured by rotational viscometers. It was found that by adding enough dispersant, the effect of particle size from 1 to 10 pm on the slurry theology could be eliminated, but a strong effect of slurry density (tested for a range of 65 to 75 wt per cent) remained. The use of dispersant transformed the slurry from Bingham plastic flow to dilatant flow, which reduced the yield stress to zero, but increased the viscosity at higher shear rates. During the milling process, the viscosity was stable. The yield stress, however, increased suddenly from zero after a certain milling time. The mill operation stopped at the point where the yield stress increased due to poor slurry fluidity. The milling efficiency was found to be higher at a lower amount of dispersant addition or a lower slurry density within the experimental limits.

Jan 1, 1993

By Moore R. F, Macias L. F

The Filbara region of northwestern Western Australia contains several known occurrences of mafic/ultramafic rock assemblages which may host platinum group element (POE) mineralisation. This paper deals with occurrences at Munni Munni and Andover. The Munni Munni complex is of particular interest because it is known to contain PGE mineralisation and is currently undergoing active exploration. The US/Australia Joint Scanner Project of October 1985 collected airborne scanner data for the BMR over Munni Munni. Such an ultramafic-mafic complex had not been previously researched with advanced remote sensing instrumentation. Extensive investigation of data from the NSOO1 (Thematic Mapper Simulator) scanner resulted in successful differentiation of gabbroic and ultramafic rocks, and also subdivision within the ultramafies. Similar differentiation could not be achieved using conventional Landsat MSS imagery and aerial photography. Encouraged by those results and in support of BMR field research into the mafic-ultramafic suites of the region, data from the Landsat Thematic Mapper (TM) instrument were investigated to attempt differentiation of the ultramafic and mafic rocks in the Andover complex some 50 km to the northeast of Munni Munni.

Jan 1, 1988

By W Farnworth, D Fergusson

Estimation of productivity is a key factor in the design of hydraulic mines and in assessing their economic feasibility. A published Russian formula for hydraulic mining monitor cutting rates overstated productivity by up to 2 tonnes per minute (251%) when applied to Solid EnergyÆs hydraulic mines. A new formula, taking into account additional productivity factors, was derived by Solid Energy and produced an acceptable correlation between predicted and actual cutting rates inNew Zealand and overseas hydraulic mines, with an average error of approximately 0.1 tonnes per minute.   Another key factor in hydraulic mine design is the transport of coal slurry via flumes. Solid Energy carried out a series of 80 full scale tests in a surface flume installation, varying the gradient and coal:water ratio. Both steel flumes and plastic-lined flumes were evaluated. A modification of the Chezy Open Channel Flow formula, including a factor for slurry density, gave a reasonable correlation between actual and predicted flows. It is believed that this Solid Energy formula is suitable for the design of flume installations for hydraulic mining.

Jan 1, 2004

By Holliday RJ

The Imperial Smelting Furnace (ISF) was developed in Britain during the 1950's as a process which could produce zinc from a blast furnace. Since then it has evolved into an efficient means of producing zinc and lead from lower grade raw materials, both of primary and secondary origin. These changes have been in response to the need to improve the cost competitive position of the ISF in a climate of decreasing metal prices. The improvements at the Cockle Creek smelter of Sulphide Corporation Pty Limited have resulted from work undertaken in four main areas: 1. Changes in plant design and operating practice to give more stable furnace operation. 2. Improvements to the quality of sinter being charged to the furnace. 3. Improved monitoring of process variables and the formulation of control strategies based on the improved data. 4. Increased understanding of the processes occuring within the furnace shaft to allow predictive modelling to be undertaken. Work in these areas is still progressing but the work to date has resulted in a significant improvement in the production rate and efficiency of operation.

Jan 1, 1984

The Newmont Waihi Operations mill has undergone significant growth over its life. Initially designed as a single SAG mill operation, the circuit has been progressively upgraded since 1988 from a nameplate capacity of 600 000 tonnes per annum to the current rate of 1.3 million tonnes per annum. With future mining potential there is renewed interest to increase the processing rate even further. Over the next twelve months five sustaining capital projects will be undertaken and two major eco-efficiency projects will be completed. With the exception of the large grinding mills, most equipment on a gold treatment plant is replaced after 10-15 years. Waihi Gold mine has been operating for 14 years and has just recently received approval to replace equipment in five main areas; carbon elution, carbon regeneration, scats crushing, intertank screens and variable speed drives. Each project has been justified on improved process efficiencies and operating/maintenance cost savings. The two eco-efficiency projects involve a water balance model and a cyanide optimisation project, both of which are Corporate key performance indicators (KPI).

Jan 1, 2002

By Boyack DJ

DEFINING AN ECONOMIC TARGETExploration usually begins with the corporate goal of finding a minimum tonnage and grade of a selected mineral. Sometimes this is expressed more simply as a minimum quantity of contained metal without any indication of the desired grade or implied profitability. Such a goal is useful in the selection of exploration areas and the planning of initial drilling programs. However, it should be reviewed as soon as significant mineralisation has been identified. To make rational decisions about exploration expenditure, the potential return from a deposit must be estimated from the outset and re-esti-mated frequently.The potential return will depend on:1. The proportion of mineral which can be economically recovered from the deposit by mining (the mining recovery).2. The quantity of valuable constituent that can be recovered after dilution with waste rock during mining and losses due to incomplete metallurgical recovery.3. Expectations of price and markets.4. Capital and operating costs applying to the selected mining and processing methods, and to transportation and marketing. Increasingly, environmental costs and constraints must also be considered.

Jan 1, 1990

A sample of tailings from a local, low grade (less than 2g/t) tailings dump was investigated for gold recovery. The tailings were very fine, with 90 per cent passing 30¦m and almost 60 per cent passing 10¦m. Tabling the coarse product from classification using a cyclone proved unsuccessful, with low recoveries being obtained due to high gold losses in the slime streams. Gold recovery by cyanide leaching was quite rapid, with recoveries of 85-90% being obtained in five hours. Lime and cyanide consumptions were 3 g/t and 0.1 kg/t respectively. Gold loading onto carbon was inhbited by the presence of the large amount of fines, so heap and vat leaching should be considered where the gold is recovered from a clear pregnant solution. Settling tests were conducted on tailings. It was observed that the addition of at least 3 kg/t lime or 0.4 kgh nonionic flocculant was necessary to promote settling of the tailings to generate a clear supernatant for gold and water recovery.

Jan 1, 1991

The economic future of the Palmer Goldfield lies with both the gold mining and the tourist industries. An equitable solution to the competition between the two involves putting a dollar value on the historical evidence there for our Australian heritage.On 23 October 1986 the Queensland Government gazetted the Palmer River Reserves R16 of 16 200 hectares, in recognition of the competing land uses emerging in the region. The intention is that historically significant gold mining sites and relics will be preserved in situ with provision for continued gold exploration and mining.This paper explores and explains the administrative process of achieving a set of Management Guidelines for Rl6 within the Queensland political milieu. The result of that process is the achievement of some of the highest preservation standards in Australia, prohibiting surface disturbance of defined Category 1 sites, and no mining proposal has yet been refused approval.The Palmer Goldfield R16 experience is a major step in achieving a co-ordinated approach to both current mining and preservation of Queensland's mining heritage.

Jan 1, 1990

Data collected from payload management systems at a number of surface mining operations show significant variance. Heavily loaded trucks travel slower up ramps than lightly loaded trucks. Faster trucks are slowed by the presence of slower trucks, resulting in 'bunching' and production losses. A stochastic model was constructed to simulate a truck haulage return cycle of 12.5 km at a large open pit gold mine in the USA. For a fleet of 35 trucks, the best estimate of the benefit achieved by a sustained reduction in payload variance of 25 per cent is a throughput increase of 1.6 per cent, within a possible error range of 0.6 to 3.2 per cent. This potential benefit is worthy of further investigation by Continuous Improvement teams at large open pit mines. The model also indicates that, under the right circumstances, provision of an overtaking lane can provide throughput benefits of up to ten per cent, The feasibility of providing unidirectional haulage circuits within large open pit mines should be examined.

May 1, 2010

The precious metallogenic belt and its geoloqical-tectonic location in eastern China.The precious metallogenic belt of eastern China is located in the western part of the Pacific gold metallogenic belt, and occurs in the upper levels of the continent cut by a deep fault structure tending NNE and NE, and active during the Mesozoic. The precious metallogenic period ranges mainly from Late Jurassic to Early Cretaceous (160 Ma-110 Ma); subordinate mineralisation occurred during the Hercynian period, and was rare in the proterozoic.Seven precious metallogenic belts are recognised from east to west, i.e. from continent to the margin active belts, as follows:1. Au-Ag-Te metallogenic belt of East Shandong Province2. Au-Ag-Pb-Zn metallogenic belt of west Liaoning-Miyun area3. Au-Os-Ir-Cr-Cu Mo metallogenic belt of Chengde Pingquan area4. Au-Ag-Pb-Zn metallogenic belt of Zhang Xuan area5. Au-Ag-Pb-Zn metallogenic belt of Zhejiang province6. Au-Ag-Se metallogenic belt of East Qinling area7. Au-Pd-Cu-Mo metallogenic belt of Wansu area

Jan 1, 1990

The Argyle AK1 Pit has been operating and producing over 25 per cent of the worldÆs diamonds by volume for over 20 years. The mining boom in Western Australia is creating upward cost pressures to ArgyleÆs mining operation while the price received for its product remains flat in comparison to many other Western Australian commodities. This incongruity, which when combined with other circumstances such as the pit being close to the end of its mine life, a decline in head grades and a tightening in operational constraints caused by the pitÆs maturity, is causing the leadership team at the mine to utilise innovative strategies in order to ensure that the open pit continues to perform economically until its final closure in late 2010. The strategies that will be discussed in this paper are step change business improvement methods, localisation of the workforce, employment of Aboriginal people and the use of a clear and concise consultation process in order to provide certainty to a workforce working in a pit during boom times where pit closure is imminent.

Jan 1, 2007

By Lai KF

The Hellyer orebody is a fine grained, massive sulphide Pb-Zn-Ag- Cu-Au deposit located in western Tasmania. Initial testwork showed that the orebody would be difficult but not impossible to treat by conven- tional flotation. A staged programme-of work was commenced to demon- strate that marketable concentrates could be produced with satisfactory recoveries. Following laboratory testing of drill core to define two flowsheets, bulk samples of Hellyer totalling 20,000 tonnes were trialled at 6 tph in the Cleveland concentrator over six months. The high through- put and extended duration of the trials ensured maximum confidence in the results and that scale-up to subsequent plants would be with a mini- mum of risk. The milling trials were successful and the Cleveland concentrator was expanded in early 1987 to treat 250,000 tpa of Hellyer ore to produce 85,000 tpa of bulk concentrates. Late in 1987 construction commenced on a 1 mtpa concentrator at Hellyer to produce separate copper/silver, lead, zinc and bulk concentrates.

Jan 1, 1988

The link between exploration success and new ideas from research and development (R&D), although often assumed, is rarely well explained or well illustrated. One issue is understanding the role of innovative ideas in the exploration process, and another is determining the relative contributing factors to an exploration success. A useful measure of gold exploration success over an extended time period and geographic area is discovery rate (θ): Discovery rate θ = gold discovered/exploration expenditure (usefully expressed as tonnes of gold per $1 million). The total gold discovered is strongly leveraged to discovery rate, as any increase in θ typically has a positive effect on exploration expenditure. Hence, improving the discovery rate is a key driver for a sustainable mineral industry, especially for gold. There are very few ways to influence θ beyond innovative R&D ideas and breakthroughs, and well-motivated and trained staff. The Australian gold industry has experienced exceptional exploration success with 9956 tonnes of gold discovered from 1979 to 2003, inclusive. This equates to: Discovery rate θ = 0.9 t/A$1 M Two-thirds of this gold has been found in the Yilgarn craton of Western Australia (6265 tonnes Au). Without this exploration success, there would have been no platform on which to build the current gold industry and to take advantage of elevated gold prices and advances in mining and processing. Several causes of the Western Australian gold success have been proposed, and more than one may be correct. Gold price, and mining and processing advances have all had influence; but exploration success and discovery of gold were essential to add to the miniscule resource base of 1979. A comparison of the exploration methods used to search for gold in the Yilgarn craton in 1979, and 1990, highlights a small number of breakthrough ideas introduced to the industry during the 1980s, and in most cases emanating directly from local R&D. By the 1990s, these ideas were being used in most gold exploration programs in the Yilgarn craton, and are still used today. These six breakthroughs are: epigenetic timing of gold deposit formation (ie after formation of rock sequence), chemical and mechanical role of host rocks, relevance of carbonate alteration haloes, gold dispersion in the regolith, optimal sampling media, and appreciation of landforms in exploration program design. Interestingly, gold exploration science in Western Australia entered the 1980s period without rigid paradigms in place regarding gold deposit formation; there was a balance between descriptive and genetic models, there was scope to research gold deposits from microscopic to global scales and there were highly effective industry research uptake processes in place: it is suggested here that these favourable conditions contributed to the exploration success and industry growth.

Jan 1, 2007

By Parker C. J, Mikula P. A

The excavation for the Sydney Opera House Parking Station comprises a large donut shaped underground cavern with a central sandstone pillar. The maximum effective roof span is about 19 m and the rock cover is between 7 m and 8 m. Permanent support for the roof and the various services tunnels consists of a combination of tensioned anchors, and untensioned dowels, and mesh with shortcrete and fibrecrete as the final lining. Steel sets were installed at main intersections.Fundamental to the design philosophy for excavation of these spans at such shallow rock cover was the use of monitoring to check on the adequacy of the installed support. Prior to excavation, extensometers, inclinometers, piezometers and surface settlement survey stations were installed. Underground survey stations, anchor load cells and shotcrete pressure cells were installed as excavation proceeded. Excavation commenced at the crown using an initial heading and three widening stages. Geological mapping during excavation confirmed borehole expectations, namely sandstone beds 1 to 4 m thick interbedded with thin shale units. Bedding plane contacts varied over short distances from tight partings to thick brecciated seams. Jointing was subvertical and joints tended to be bed-limited.

Jan 1, 1993

By Daxian Z, Youdi Z, Shucai Y

The Huolinhe surface mine is a very large-scale surface coal mine, located in the north-east area of China with a production rate of 1.2 Mtpa. Its coal haulage system has a large capacity, long transportation line and high degree of automation. The system comprises two crushing plants, many belt conveyors, four surge bunkers, one loading bunker, one coal storage and five end product bunkers. In this paper, the network patterns of semi-continuous systems in surface mines are studied, the reliability calculation methods and a simulation model are established and the software for computing the reliability of a semi-continuous system is worked out. By considering the whole coal haulage system in the Huolinhe surface mine, the authors developed the system reliability-numerical simulation method. The steps and the computing results of this method are described in detail. Through the calculation, we can master the present situation of system reliability and the main factors impairing system reliability, expose the system weak links, put forward the ways of enhancing system reliability and furnish the basis for improving the system and equipment. The way of increasing capacity and methods of enhancing system reliability are further raised.

Jan 1, 1995

By Bhattacharyya A. K>

The Pemali Open Pit Mine is situated in a small island called Bangka in Indonesia. It produces approximately 165,000 m3/year of tin ore with an average grade of 3.67 kg/m' of tin from a primary deposit. The deposit occurs at the rim of a granitoid intrusion within sedimentary beds. The rock formations, all extremely weathered, and the overlying alluvium, are exposed to a rainfall exceeding 3m/year. Serious slope stability problems are experienced at the mine, despite using overall pit slopes of 20¦-29¦, the latter resulting in a stripping ratio of 4:1. This paper outlines a computer based back analysis of a major slope failure involving some 250,000 m' of material which occurred on the west wall of the pit in February, 1984. The findings from the analysis, together with other information, are used to examine the stability of the east wall of the pit, where tension cracks developed later. The results indicate that the large influx of water was the most significant cause of such slope stability problems and a more intensified water management programme would be beneficial.

Jan 1, 1989

By Gordon N

The in situ behaviour of claystone floors associated with the Wallarah, Great Northern and Fassifem Seams has been studied using a comprehensive suite of stress and displacement monitors. The instrumentation was supplemented by in situ and laboratory testing of the claystone materials. The instrumentation demonstrated that the presence of claystone floors is associated with floor heave, extra rib spall, and settlement of the pillar into the floor. Horizontal floor extensometers showed that the depth of extrusion of clay was limited to 1-2 in. A pore pressure transducer installed in a claystone floor demonstrated the possible existence of short-term undrained behaviour of the claystone. Long term swelling of destressed claystone was also documented. Settlement of pillars into claystone floors can be analysed using simple elastic theory. The assumption of plane strain is valid for most claystone thickness/pillar width aspect ratios. Floor heave can be analysed using bearing capacity concepts. However, it is considered that heave is the result of local bearing capacity failure in the rib spall zone. The advantage of this model is that the bearing capacity equation can be applied without resort to unrealistically high factors of safety.

Jan 1, 1992