Search Documents

A Modelling Approach Using a Back-Calculated Induction Time to Predict Recoveries in Flotation

Sep 13, 2010

By G Wood, B Lumsden

A statistical ærandomised block designÆ full plant trial of magnetic conditioning of flotation feed was undertaken at Rio TintoÆs Northparkes Mine in New South Wales. Magnetic conditioning of flotation feed has been shown to improve the flotation of 20 38 ¦m fraction for either metal. Approximately half the copper and gold losses at Northparkes are in the

Jan 1, 2007

A three-dimensional finite element analysis is used to determine the stress intensity factors associated with the chevron-notched semi-circular bend test specimen. The stress intensity factor calibration is done over a range of crack lengths a

Jan 1, 1998

Higher commodity prices and environmental considerations will make selective narrow-vein mining more attractive in future. Unfortunately, hand-held airleg (jackleg) mining is a mature technology that has safety and productivity limitations. Despite decades of attempted innovation, no obvious successor to airleg mining has emerged. A review of some of the possible technologies is followed by a speculative description of the mine of the future, intended to stimulate thinking and discussion during the conference.

Jan 1, 2008

By Robertson GE, McLaughlin JD

An extensive laboratory campaign was conducted to find a suitable water soluble collector to replace diphenylguanidine (DPG) in the matte separation process. The examination of the collectors was done by measuring the rate of flotation and the best candidate collectors were selected on the basis of the rate parameters. As a result of this search mercaptobenzothiazole (MBT) was selected for a plant trial. A plant trial of two weeks duration confirmed that MBT will produce separations at least as good as those obtained with DPG.

Jan 1, 1993

By W F. Bawden, J T. Paynter

This investigation involves laboratory testing and stability analysis of paste fill at the Golden Giant Mine. Site-cast samples are tested in unconfined, confined, and consolidated-undrained triaxial compression. Pore pressures during shear and consolidation characteristics are measured to determine both drained and undrained shear strength parameters and assess the potential for undrained loading. Liquefaction potential is also considered. A limit equilibrium solution is used to obtain factors of safety against failure of the fill during mining of adjacent stopes.

Jan 1, 1998

As world demand for various minerals increases the mining industry in its endeavour to satisfy this demand will, eventually,look to the extraction of orebodies which previously may have been uneconomical to mine. These orebodies may be of two types. Firstly, new low grade orebodies and secondly, remnant sections of previously mined orebodies. Some of the factors relative to remnant mining operations are discussed and the potent- ial of remnant mining in providing an important contribution to future world metal production is considered.

Jan 1, 1975

By Fulton E, Ring RJ, Waters DJ

The Nabarlek uranium treatment plant of Queensland Mines Limited (QML) is currently treating 600,000 tonnes of ore which was mined and stockpiled in a single four month period prior to commissioning of the plant. During the mining phase, material from the open pit was sorted into ore,'below ore grade uranium material (bogum) and waste using a truck discriminator (radiometric analyser) developed by Australian Mineral Development Laboratories (AMDEL). Ore was stockpiled in a single heap with the location and grade of each truck load being recorded. Bogum and waste were stored separately. From the information recorded, both computer and physical models of the stockpile were constructed. These models are currently used in the planning of day to day reclamation of ore from the stockpile.

Jan 1, 1984

This paper examines the methods and people required for the evaluation of project or corporate acquisitions. Experience over the past five years has shown that some growth can be achieved by carefully evaluated acquisition of gold projects within regions where the acquiring company has gold processing facilities. Many Western Australian companies have participated in this process and the trend seems likely to continue with a diminishing number of larger producing companies controlling through joint venture or direct purchase of widely spaced ore deposits. In some cases the acquisition may include ore processing facilities, however an increasing number of smaller project acquisitions, involving small open pit gold deposits, which are within trucking distance of the acquiring company's mill. Whilst gold prices remain at the current depressed level we can expect to see this trend continue.

Jan 1, 1989

INDEX OF CONTENTSIntroduction.Systems of classification of coals.RankClassification of Australian coals.Defects of systems in use in other countries.Indexing by Fuel Ratio.Classification by Ultimate Carbon/Ultimate Hydrogen.Relationship between Fuel Ratio and ultimate composition.Suggested convention for classification.Origin and Evolution.Notes on directions of change of composition on Carbon Hydrogen chart.Summary and conclusion.Acknowledgments.Bibliography.Appendix.

Jan 1, 1948

Construction of Western Mining Corporation's nickel refinery at Kwinana, Western Australia, commenced in July, 1968. Production of 15,000 tons per annum of refined nickel metal will commence early in 1970, The plant will also produce approx- imately 150,000 tons of ammonium sulphate0 The ammonia leach process which was developed by Sherritt Gordon Mines Ltd., and has been in operation at their plant at Fort Saskatchewan, Alberta, Canada, for the past 15 years, will be used at Kwinana. The refinery will cost approximately 435 million, and will employ upwards of 250 people.

Jan 1, 1969

By Kwok S, Haemmerle A

Treatment methods for a low grade deposit at Mt. Fitch near Rum Jungle, N.T., were investigated. Physical beneficiation of the ore, sulphuric acid leaching, carbonate leaching and various methods of uranium extraction from the leach liquor were studied. Although the deposit occurs in a carbonate environment, acid leaching of the ore after beneficiation by radiometric sorting appears to be the most economic treatment method. Uranium would be recovered from the leach liquor by solvent extraction.

Jan 1, 1970

A number of small copper deposits occur in the Pernatty Lagoon-Mt. Gunson area. Textural and mineralogical differences distinguished the lagoon sulphide deposits, which occur in a water filled basin of permeable bedrock immediately under the lagoon floor, from the largely oxidized deposits which occur in the low hills adjacent to the lagoon deposits.Groundwaters are carrying copper, and to a lesser extent zinc, downstream to the lagoon. Several species of sulphate-reducing bacteria are widespread in the groundwaters and lagoon muds.It is suggested that copper sulphides were first deposited at the same time as, or soon after, the host Proterozoic sediments, and that during the present cycle of erosion the lagoon deposits may have been enriched, or largely formed, by bacterial precipitation of copper sulphides from laterally migrating cupriferous groundwaters.

Jan 1, 1971

By Adranyl W. W

Sub-level caving with bottom ore drawing has gained wide acceptance in rich, soft, low magnetic iron ores because it provides moderate ore dilution and ore losses. The main problem here is the high rock pressure exerted on sub-level drives situated in the sub-level sill pillars. To reduce this effect, the ore block is divided into panels. This paper illustraes the method of determining the maximum panel width providing low maintenance cost of sub-level drives.

Jan 1, 1995

The cost of constantly extending a decline tunnel that plays a part in the actual extractive process is a revenue cost. The characteristics of such a decline tunnel are that it is dug in a series of relatively small excavations. It follows the ore body and is dug as close to the ore body as practicable. In addition, the decline allows for the extraction of ore in the immediate vicinity, with the ore being extracted in a relatively short period of time.

Jan 1, 1990

By Watt KL

Chemical anchors for use in rock bolting have been produced in Australia under licence for several years. These anchors are alternatives to the more normally used mechanical anchors and give improved anchorage strengths under some conditions, although at greater cost. Considerable development during this time has resulted in an improved sausage-type chemical anchor more competitive in price, to such an extent that its use is increasing markedly. Particular-improvements allow load application up to the strength of the bolt within 2 min, reduction in cost, self-extinguishing features in the resin, improvements in manufacturing techniques, and an improved water- insensitive casing. At the same time, smaller bolt sizes have allowed reduction in resin volumes with consequent cost reduction. At this stage several aspects remain to be improved, particularly specialty anchors for specific purposes and Packaging.

Jan 1, 1971

By Van Rooyen F

An introductory review of the current grade control blasting techniques (selective mining strategies) used in the Eastern Goldfields has recently been undertaken. The survey was initiated and conducted by the Western Australian School of Mines. Four distinct selective mining strategies have been identified and a number of trends have been highlighted. Many operations, however, have developed techniques which use a hybrid method to suit the site conditions. The aim of all the mining strategies is to produce an optimum product. The optimum product is one which contains no diluent and experiences no mixing of the various identified ore and waste blocks and is fully reco- vered at the minimum overall operating cost. Due to this unified aim all of the grade control blasting techniques have many common design Features.

Jan 1, 1988

The development of paraprofessional courses in metallurgy and related disciplines, by the Department of Technical and Further Education in New South Wales, is outlined in this paper. The changing nature of metall- urgical educational requirements is summarised, and various attendance patterns discussed. The potential advantages of the sandwich system of College attendance, to the more distant sectors of the mineral processing and metallurgical industry is outlined. Some of the likely future trends in technician education are presented. These include the need to respond to the changing expectations of technician employers, as shown by industrial surveys, the role of experiential learning, the need to integrate courses so that students can build on prev- iously completed courses, the possibility that future technicians will require a multi- disciplinary background and the provision of easier access to technical college facilities by potential students and industries.

Jan 1, 1978

By Lye GN

Rock mechanics investigations have shown that some major slopes in the Panguna pit would be stable at angles in excess of 500 providing near-surface instability could be controlled. Excavation of final batters at angles between 55¦ and 60¦ is now being carried out using D10 dozers with berms at 45 to 60 m centres. A trial slope with berms at 90 m centres is planned. Shotcreting of weak zones combined with crest reinforcement, with rock anchors and dowels, is used to provide protection against erosion and toppling of the crests. Overall slopes excavated in this way are of the order of 10¦ steeper than slopes obtained by blast and shovel excavation.

Jan 1, 1986

By Davies L, Jeffreys J

The Broken Hill Proprietary Company Limited (BHP) has been successfully using mini computers in its open cut strip and pit coal planning for the past six years. A recent development within the computerised Seam deposit User oriented Mine Planning System (SUMPS) provides the facility for the generation, evaluation, and simulation of colliery workings.Existing computer programs for collieries were studied, but none met the requirements of BHP's underground mine planners.Consequently, it was decided to develop programs, based on those existing within BHP for open cut strip and open cut pit mine planning. The new planning facility was designed to enable any number of proposed colliery developments and operating plans to be evaluated against optimistic, most likely and pessimistic geological lease area interpretations.In mine planning, sensitivity studies should be conducted to determine the likely effects on production, development costs and colliery economics of changes in mine design and budgeted equipment productivity. By automating the manual calculations involved, the computer programs provide the ability to conduct numerous and extensive sensitivity studies. Hence an optimum mine design for budgeting purposes can be derived quickly with an improved degree of confidence in the long term viability of the proposed development.

Jan 1, 1982