Search Documents

By L. B. Smith

Introduction The property of Wright-Hargreaves Mines, Limited is situated at the northeastern end of Kirkland lake, Ontario. It lies immediately east of the Lake Shore mine, and about in the centre of the Kirkland Lake camp. The district is served by the Swastika-Rouyn branch of the Temiskaming & Northern Ontario railway, the town of Kirkland Lake being four miles northeast of Swastika, which is 63 miles north of Cobalt and 392 miles north of Toronto. The mine is developed by three shafts and has more than twenty-eight miles of underground workings. There are two main producing veins, which lie in a porphyry boss 1,350 feet wide. Milling started in May, 1921, and to-date (January, 1933) the mine has produced gold to the value of $21,770,183. Present production is at the rate of 800 tons of ore per day. For a description of the geology, reference may be made to the report by E. W. Todd on the Kirkland Lake Gold Area (1). Structure and Ore Deposits The two major productive veins on the Wright-Hargreaves property are known as the North vein and the South vein. In the vicinity of the shafts these veins are approximately 550 feet apart. A third vein, known as the Inclined vein, has been worked from its junction with the South vein at the 2,000-foot level to its intersection with the North vein at the 800-foot level. This inclined vein has to date been found only in the area east of the eastern major north-south fault. The main North vein and South vein have a general vertical dip, although local rolls and post-ore faults throw certain sections out of line. From the surface to 3,900 feet, the North vein is displaced south less than 200 feet, and the South vein at the same horizon is almost perpendicularly beneath the surface showings.

Jan 1, 1934

By William D. Swank, Prabhat K. Tripathy, Tedd E. Lister, Eric S. Peterson, Delon C. Haggerd

More than half of the primary neodymium, produced directly from ores, is being used to manufacture neo magnets. Neodymium, being a critical element in supply, has attracted considerable interest worldwide to recover this metal from a variety of waste streams. From among different recycling processes, hydriding-dehydriding can prove to be highly effective in recycling discarded neo magnets present in consumer electronics. In the present study, manually removed magnets from discarded Hard Disk Drives (HDDs) were subjected to the hydriding-dehydriding process in order to evaluate the resultant products for the re-fabrication of the magnets. The paper describes the effect of experimental parameters on both the hydriding and dehydriding processes as applied to different magnet chemistries.

Jan 1, 2014

By A. O. Sfriso

"Numerical modelling is becoming universal in rock engineering practice. Most applications focus on the prediction of failure loads of 2D problems, where the numerical models are useful extensions to analytical methods and experience-based design criteria. For 3D problems and problems where the assessment of serviceability indicators – displacements, ground-structure response, etc. – are of importance, the selection of the constitutive models themselves and the implications of the selection of material parameters may have a very heavy impact on the reliability of the model outcome and its predictive capability.This paper overviews basic common aspects of constitutive equations used in practical rock engineering and summarizes some challenges that are frequently observed when reviewing numerical models performed for routine problems in rock engineering. INTRODUCTIONNumerical methodsFrom a philosophical perspective models, either analytical or numerical, are idealizations of a perceived reality. For us engineers, models are just tools we use to guide our judgement and understanding of the problem in hand. When dealing with problems in rock engineering, we resort to a wide range of techniques:1. Closed form solutions like confinement-convergence methods for circular tunnels: these methods satisfy equilibrium and compatibility requirements at the cost of a crude simplification of the material behavior and geometry;2. Limit analysis methods, like bearing capacity formulas: lower bound methods satisfy equilibrium but sacrifice compatibility, and upper bound methods do the opposite. Material behavior must be simple, geometry admits limited freedom;3. Limit equilibrium methods, like method of slices for slope stability: they satisfy restricted forms of equilibrium, do not satisfy compatibility requirements, require simple material behavior but have a much greater flexibility on geometry;4. Numerical methods, where a mesh is employed to discretize the problem geometry: when properly formulated, these methods satisfy equilibrium and compatibility requirements and give reasonable approximations to the behavior of very complex geometries and construction sequences. Very little restrictions remain on geometry and material behavior, but the cost of calibrating the material parameters can be very high."

Jan 1, 2015

By Dean Gerhardt

Why the need for proactive loose detection? ?? Past history of ground falls in Saskatchewan mines prompted research into new techniques for ground control. ?? Traditional tools for ground assessment (i.e. visual inspection, sounding with scaling bars) are not proactive and can often be time consuming. ?? Need existed for a system that was non-evasive, time efficient, and could be managed by a single operator. Ground Penetrating Radar (GPR) immerged showing the greatest potential.

May 1, 2008

By A. Dave Mackintosh

The Current demand for potash has pushed world prices to record levels and allowed Saskatchewan producers to operate at maximum capacity. Several years of strong demand has resulted in a permitting rush not seen since the 1960?s. Even though Saskatchewan has a huge potash resource, mining and processing constraints will limit the areas of economic development. Introduction In 1969 M. E. Holter prepared a report ?The Middle Devonian Prairie Evaporite of Saskatchewan?, published by the then Dept. of Mineral Resources. Holter?s report has remained the bible of geologists working in potash ever since. It is astounding that a report written before there was really much potash mining history in the province, is as valid today as when it was first published. This paper re-iterates much of Holter?s report and adds a little mining experience to essentially confirm the importance of his work.

May 1, 2008

By U. Caliskan, S. Miskovic

Gravity separation is a technique that depends on the difference in density of minerals for their separation. Although this method is one of the oldest separation techniques, it is still preferred in the industry because of its low capital and operating cost while it is environmental-friendly. In this paper, we present a new numerical methodology that can be used to investigate dynamics of dense slurry flows in gravity separation systems. A simple channel with a set of riffles is selected as a test platform in order to observe the effect of the riffle shape on segregation profile of particles with different densities. It is believed that the riffle shape would affect the slurry flow and possibly cause one class of particles to segregate within the riffle zone. The turbulence, as a disturbance effect within the riffle zone, causes heavy particles to displace the light, that is, the heavy particles will be trapped in riffles, while the lighter particles are carried by water to the end of the channel, which is an example to uninterrupted suspension. MP-PIC model in OpenFOAM is used to study the effect of riffle shape and slurry percentage of solids in this simple gravity separator on particle segregation profile of four discrete mineral density classes, which are Quartz/Clay (SG 2.6), Pyrite (SG 4.2), Chalcopyrite (SG 5.1), and Gold (SG 19.32). Gold particles are found to be readily captured and retained in the riffles because of their high density, while particles with the intermediate densities are more influenced by the flow. The developed model framework has been proven robust and capable of providing physical results even for the flows with a very high percentage of solids, characteristic for mineral processing operations. INTRODUCTION Gravity-based ore concentration techniques make use of differences in density of minerals within an ore to enable separation of valuables from the gangue. As some of the oldest techniques used for ore beneficiation, they are known to offer a range of benefits such as low specific energy consumption and low capital and operating costs (Burt, 1999; Falconer, 2003; Holland-Batt, 1998), however, they suffer from low selectivity, poor separation efficiency, and low capacity. Gravity separation techniques are common practices in the mining industry and are employed widely for the precious mineral concentration, iron ore recovery and coal preparation (Kroll-Rabotin, Bourgeois, & Climent, 2013; Laplante & Spiller, 2002; Williams, 1997). For example, gravity separation systems are highly applicable for precious metal enrichment operations by being included in primary grinding circuits, shaking table tailing separation, pre-concentration of leach feed and flotation concentrate enrichment for both flash and conventional flotation purposes (Burt, 1999; Falconer, 2003; Holland-Batt, 1998; Laplante & Spiller, 2002; McAlister, 1992). Gravity separation can be employed in the copper processing circuits by being integrated into the pre-flotation circuit to capture the gravity recoverable gold (GRG) and any free copper aiming to enhance the gold and copper recovery of the plant. When native copper and GRGs are present in the deposit, this integration not only facilitates plant overall performance via removal of the valuables early in the circuit, but it also reduces downstream operational expenditures due to less retention time of coarser copper particles in the system.

Jan 1, 2019

By Randy McMeekin, Chris Twigge-Molecey, J. Peter Blake

The project implementation phase, FEL4, is generally a complex undertaking. The project has been approved for construction and the capital has been allocated. At this point the project team comes under significant pressure to meet the safety, schedule, cost, and start-up committments. For the design team the principal tasks are to finalize detailed design, complete procurement, and issue construction contracts. Design activities must be closely coordinated with equipment and material procurement. A clear engineering plan should be based on well-defined work packages to meet construction, commissioning, and startup requirements. A range of review processes by discipline, area, and third parties assure quality. Constructability, safety, and hazard reviews are performed throughout the design process. Three-dimensional models that incorporate extensive databases help to maximize efficiency and minimize errors. Well-managed projects have a clearly accountable design team, rigorous change control processes, and well-defined workflows. Key individuals from the design team participate in commissioning, operator training, and startup.

Jan 1, 2015

By N. A. Warner

Virtually zero gas emission smelting is promoted as a means for securing environmental advantages and the general public’s acceptance. Concerns about climate change will increasingly make it more difficult for new primary metals projects to come to fruition unless greenhouse gas emissions are decreased. Assuming a sustainable market for sulphuric acid is not locally available, the next best option is high temperature reaction of strong SO2 with limestone or dolomite. This is followed by CO2 liquefaction and disposal either underground or in the deep ocean. The Voisey’s Bay nickel project is cited as an example where appropriate location of a new smelter close to large dolomite or limestone deposits would lead to a virtually zero gas emission operation. Most of the electrical energy required for producing technically pure oxygen and for liquefying CO2 and transporting it to disposal can be derived from smelting a bulk sulphide concentrate and then reacting SO2 at high temperature. Provided the smelter gases are properly cleaned before sulphur fixation, the sulphated stone should be uncontaminated and environmentally benign and possibly of use in the building and construction industry.

Jan 1, 1999

By Thomas Mütze, Frank van der Meer, Gunnar Kretschmar

"The air classification of moist bulk materials is addressed in the literature insufficiently. Therefore a feasibility study investigated the influence of feed moisture on the separation efficiency expecting a reduction with higher moisture content in the feed. Two iron ore samples were characterized in terms of the nature of bonding of moisture as well as its effect on the agglomerate strength. The classification tests themselves were conducted with two dynamic laboratory air classifiers at cut sizes from 45 to 110 µm and a moisture of the feed material between 0 to 10 wt.-%. The quality of classification was assessed by split factor, cut size, separation efficiency, moisture of both products, as well as the yield of the fines as product fraction in a corresponding processing plant. An initial approach was found for a technological implementation: A sufficient drying of a moist feed can be realized simultaneously to the pneumatic transport inside the classifiers. In the present case the drying effect and dispersion intensity was sufficient to provide good separation results up to 3 wt.-% feed moisture. An additional drying step was necessary beyond 3 wt.-%.INTRODUCTIONSpecific information about the influence of moisture in air classifiers is very rare. Mostly only dry products are processed and/or drying prior to classification is recommended. Apart from the specific influence of the feed moisture a lot of literature can be found regarding air classification itself. Altogether air classification can be divided into several sub-process (Leschonski, 1977):- dosage of the feed material,- dispersing the solid feed material into a gas stream,- feeding the dispersed material into the classification zone by pneumatic conveying,- separation of coarse and fine particles, and- separation of fine particles from gas.For wet feed particles also drying plays an important role. Interesting for the present investigation are the humidity of the feed and its influence on the single sub-processes."

Jan 1, 2016

By François Charette

High stress conditions in underground mines push the performance envelope of support systems to their limit. In weak rock masses these conditions lead to large deformation and breakdown of the rock material, while stress release events in hard rock mines can lead to sudden and usually violent rock and support failure. In typical support systems, a combination of different reinforcement and support mechanisms provide the required convergence control and retainment. These systems usually involve a multi-pass support installation. The advantages of a single pass support system are investigated and several bolting combinations are compared. Criteria for design are reviewed and new criteria are proposed to include cost and effectiveness in commonly used engineering approaches. Field observation and testing is used to illustrate the difference between the proposed approach and more conventional systems.

Nov 1, 2011

By H. -L. Heikkilä, E. Peuraniemi

"Boliden Harjavalta Oy has a long tradition in the Finnish metal industry starting from the 1930's. The Smelter consists of copper and nickel flash smelting lines. Off-gases are captured in the acid plant to produce sulfur products. During the early years of production, the surrounding environment suffered from high SO2 and dust emissions. The first acid plant started in 1947, a few years after commissioning of the smelter. The flash smelting method was developed and commissioned in 1949. This created the basis for today’s environmentally sound metal production. Recent air emission reductions are related to treating lean ventilation and granulation gases. Emissions from the stacks are monitored with continuous measurement devices. SO2 and PM10 concentrations are also measured from the residential area and reported online in cooperation with Harjavalta community and other local industry.INTRODUCTIONProductionBoliden Harjavalta Oy smelts copper and nickel concentrates and refines copper in the western part of Finland. The copper concentrates come from external copper mines mainly in South America and Europe. Concentrates are unloaded at the Pori harbor and transported to Harjavalta by train from a distance of about 60 km. Boliden Harjavalta Oy has operations in Harjavalta and Pori. The smelter in Harjavalta produces copper anodes that are transported via railway to the copper refinery in Pori. The anodes are electro-refined into copper cathodes and by-products like Se, Ag, Au and Pt/Pd concentrate. In the Harjavalta smelter SO2 containing gases are delivered to a sulphuric acid plant where sulphuric acid and liquid sulphur dioxide are produced.Our nickel smelter smelts nickel concentrates on a tolling basis to produce nickel matte for customer needs. SO2 containing off-gases are delivered to the sulphuric acid plant for sulphur capture and modification into products.All our operations are certified according to the Quality, Environmental and Occupational Health and Safety Standards ISO 9001, ISO 14001 and OHSAS 18001. Boliden Harjavalta Oy was the first company in Finland operating in the metal and technology industry to be certified according to the Energy Management Standard EN 16001, currently this certification is done according to ISO 50001."

Jan 1, 2012

By P. D. Soares, H. R. Bullis, R. A. Hureau

"Echo Bay's Lupin Operation has produced more than 2.15 million ounces of gold since start-up in 1982. The mining method used to the£ present time has been longhole open stoping using trackless equipment. Because direct measurement of the open stopes has not been possible until recently determining the exact quantity of unplanned dilution in previously mined stopes has not been possible. Estimates of dilution hove been mode using comparisons between production tons and grades against ore reserve tons and grades.This paper discusses tracking of grade and tonnage measurements from reserve estimation through production. Comparisons between estimated and actual tons and grade are presented~ along with a brief description of methods used at the Lupin operation to control dilution."

Jan 1, 1994

By Bird. M.

As the Cadia mill was the first 40ft diameter SAG mill, commissioned in 1998, its performance, liner and discharge design attracted considerable international attention. Twelve years on, the liner design and the control philosophy are being readdressed to further improve the mill?s performance. A comprehensive series of 3D liner scans, over life of the liner, have been used to calibrate liner mass loss and progressive changes in the liner profile. This data is being used to provide true charge mass and mill filling, plus progressive trajectory profiles over life of liner. This information, along with measures of mill performance over liner life, is being used to select the optimal operating conditions as the liner wears, and hopes to inform future liner design.

Jan 1, 2012

By C. F. Starr

This paper deals with the various types of cable in use in mines, with special attention paid to their construction. There will be a few comments regarding the different insulants, jacketing materials and armouring used, depending on their application. Governing standards and the differences therein will also be discussed.

Jan 1, 1969

By Daniel J. Corkery

Mines in Canada and the United States are subject to regulations limiting ammonia, nitrate and nitrite levels in mine effluents released into the environment. The primary source of these nitrogen compounds is typically explosive used in blasting operations, as ammonium nitrate (AN) remains a significant component of most explosives used in the mining industry. The amount of AN entering a local water drainage system is related to site conditions, explosives used, explosive handling and blast efficiency. Mining operators acknowledge AN loss to mine water from blasting operations. However, the mechanisms by which ammonia, nitrite and nitrate are entering the water drainage system, or the relative contribution of specific mechanisms, may not necessarily be assessed or monitored adequately. Characterization of these mechanisms, through systematic investigations, allows a mining operation to focus its efforts on reducing AN loss. This paper outlines a strategy for investigating the mechanisms through which AN enters the mine water drainage system and methods to mitigate this loss. This strategy includes collection and analysis of data to identify and quantify the AN loss mechanisms, design and implementation of tests to mitigate this loss, and assessment of the results. Such investigations are not intended to be a separate one-time project, but part of a long-term process of continual feedback and optimization that is related to the collection and reporting of AN levels for regulatory purposes. The implementation of the strategy must be tailored to each mine?s requirements and existing conditions.

Oct 1, 2010

By M. S. Badollet

"The study of the physical properties of asbestos minerals requires a careful isolation of the fiber from the wall rock and, at a later stage, a comparison of these physical properties with those of fibers that have passed through the milling and beneficiation processes.The effects of mineral impurities, loss of fiber length and the formation of extreme fines (asbestic and/or associated minerals) often show up in the formation of special asbestos products as well as in the commercial production of asbestos papers, mill-boards, asbestos cement products, plastics and insulation materials, and in the filtration of blood plasma and wines.Numerous test methods have been developed in Canada and in England for use in the asbestos industry. Special treatments of asbestos fibers have been used to improve their physical and chemical properties and to eliminate impurities.Numerous problems connected with the use of asbestos fibers are discussed, such as the effects of asbestos on filtration, surface area, surface treatments using organic or inorganic materials, the surface charge on the fiber, the presence of magnetite and air pollution elimination. Biological studies on finely ground asbestos, when dispersed in 0.9 per cent sodium chloride solution and then sterilized and injected into hamsters, show that by reducing the dose, the tissue damage can be largely avoided. In these experiments, Arizona asbestos fibers were carefully extracted from the wall rock, finely ground, and examined chemically and micros-copically for any mineral impurities that might be present so that any effect on the hamsters would be directly due to the presence of the asbestos. The harsh Arizona fiber induced more extensive tissue response than the soft fiber when tested in hamsters."

Jan 1, 1969

"AbstractThe Sedimentary Basin area of Western Canada, which lies between the Precambrian Shield and the Cordilleran mountain area, covers approximately 800,000 square miles. Sediments ranging in age from Cambrian to Tertiary are present and, of these, horizons in the Upper and Lower Cretaceous, Jurassic, Mississippian, and Devonian have yielded commercial oil and gas flows. Producing horizons in the Cretaceous and Jurassic are sandstone, while all those of the Palaeozoic are carbonate rocks such as red limestone or dolomite (bioherms). Shows of oil and gas have been encountered also in the Cambrian and Triassic sediments.The broad structural features of this vast expanse of sedimentary rocks are the Moose Jaw syncline, the Sweet Grass-Battle River arch, the Alberta syncline, the Foothills belt, the Rocky and Mackenzie mountains, the Great Bear-Slave Lake basin, and the Mackenzie Delta Basin area.This contribution outlines the .stratigraphy and structure of the Basin area, and gives examples of present producing oilfield structures and stratigraphic traps.Part 1.-Regional StratigraphyIntroductionThe vast expanse of relatively undisturbed sedimentary rocks of western Canada has long been recognized as prospective territory to search for oil and/ or gas. This search in western Canada dates back before the turn of the century, but, considering the size of area to be explored and tested, the effort an<l money expended upon it, which, before the recent discovery of oil at Leduc, Alberta, appeared large and fruitless, now seems almost ridiculously small. A check-up of effort and money expended prior to and since the Leduc discovery would undoubtedly reveal that more wildcatting and development has taken place during the last two and a half years than during all previous years combined. The figures would astound not only the average citizen, but many within the industry itself."

Jan 1, 1950

By C. Tasker

Introduction In the Early part of 1930 the Ontario Research Foundation was asked by the Minister of Mines, the Hon. Charles McCrea, K.C., M.P.P., to undertake a technical and economic investigation of the Northern Ontario lignite deposit. This investigation has been under way since June, 1930, and has necessitated considerable work at the deposit, in the laboratories of the Foundation, and at test plants in Europe. All the work has been carried out in active co-operation with the Provincial Department of Mines, the Deputy Minister, Mr. T. F. Sutherland, and several of his technical colleagues being associated with members of the staff of the Foundation on the Advisory Committee, which has met at frequent intervals to co-ordinate and direct the various lines of research. An interim report was made to the Minister of Mines by the Director of the Foundation, Dr. H. B. Speakman, at the end of December, 1932, and is at present under consideration by the Minister. This report deals with the extent and character of the deposit, the methods and costs of mining, and the methods and costs of processing raw lignite, the characteristics of certain lignite products, and the technology and economics of present fuel utilization by railways, industry, and domestic users in northern Ontario. It is not the purpose of the author to discuss in this paper either the geology of the deposit or the economics of the mining, processing, and utilization of lignite, but rather to deal briefly with some of the technical problems investigated by the Foundation during the study of the characteristics and methods of utilization of Northern Ontario lignite. Some mention, however, of the work carried out to define the extent of the deposit is a prerequisite to any discussion of the nature of the lignite.

Jan 1, 1933

By Nathan Ferdinands

Outline Overview of Site and Partners ?MeanduMine ?Thiess?GroundProbe Technology ?Work Area Monitor (WAM) ?Software control ?Alarms MeanduMine King2East pit failures ?Background, and Northern Failure ?Southern Failure Recovery and conclusion

Nov 1, 2011

By Paul Clayton

Case Study ? Site: BMA Saragi Coal Mine Queensland Australia ? Model: Marion 8050 ? YOM: Mid 1970s ? Boom: 97M ? Bucket: Original capacity of 100 Tonnes upgraded to 125 tonnes at time of filtration upgrade. ? Apps: Swing, Hoist & Drag Gearboxes ? Oil: Oil Castrol Alpha TT1200 Viscosity of 1208 cSt @ 40° C (104° F) 720ltr Oil Volume Trial and Installation Justifications ? To reduce gearbox overhauls. Typical schedule being 5 years. ? Bucket upgrade from 100 tonnes to 125 tonnes. Increased gearbox demand and stress. ? Increase of overhauls out to 10 years + ? Saving per Dragline estimated to be US$8-10M in downtime and maintenance if successful. ? In compliance with BHPBilliton Global Maintenance FLAC program ? Fuels, Lubricants, Air and Coolants ? Cost Justification ? Downtime: 4 days ? Lost production: $420,000 ? Cost of parts: $162,000 ? Labour and misc: $41,000 Gearbox failure cost $623,000

May 1, 2008