Search Documents

By Martin Bouchard, Bruno Paillard, Jean-Claude Dubé, André L’Espérance

"A precise analysis of the noise emitted by an aluminum plant has shown that one of the main sources of noise is the noise emitted by an exhaust stack 40 m high and 1.8 m diametre, emitting a pure tone at 320 Hz. Because a classical cost effective solution is not available for this source, active noise control (ANC) solution was investigated.Commonly available ANC systems, how-ever, are not applicable to the chimney considered because the diameter of the stack (f) is too important compared to the wave length(?)of the frequency to control. In fact, until now, active noise control (ANC) has been successfully used to reduce the acoustical energy emitted at the end of ducts in the case of plane wave propagation, i.e. ?/f< 1.7 [1,4].When f> ?/1.7, high order modes propagate in the duct and a single canal active noise control system is not sufficient.This paper presents an ANC system developed to control higher modes in a circular duct. The controller used is based on a multiple-input, multiple-output adaptive filtered X-LMS and allows up to 11 error micro-phones and controls sources. The system has been used in a laboratory on a finite duct of3.5 m long and 0.30 m diameter which corresponds to the same ratio ?/f for the real stack. The efficiency of the system with different numbers and location of control sources and errors sensors has been analyzed. Noise reduction of 15 dB(A) could be obtained with some configurations. Actually, the system is being considered for installation on the real chimney stack."

Jan 1, 1997

By Y. Champoux, N. Atalla, R. Oddo, C. Lesage

"Percussion drills are the source of the most serious noise problems in mining activities, due to their extremely high noise levels(114-122 dB(A)) and widespread use(Bartholomae and Stein, 1988). Percussion drills will continue to be widely used to drill small diameter holes in hard rock because no other method seems to be economically avail-able to replace them (Boillat et al., 1993).Many studies (Danière, 1991; Hawkes etal., 1977a; Jensen and Visnapuu, 1972;Leblond et al., 1976; Milette, 1989) were con-ducted to determine the major noise sources of percussion drills. The exhaust air of pneumatic drills, the hammer, the bit in contact with the rock and the drill rod have been identified as the major noise sources. A muffer can be used to reduce the exhaust noise and the hammer can be enclosed. The bit noise is considered to be of concern only at the beginning of holes. When all the available methods are used to reduce the noise of a percussion drill, the drill rod vibrations become the dominant noise source (Hawkes and Burks, 1979). However, the noise levels generated by this source remain high and future efforts should concentrate on reducing its radiation.Works by Hawkes and Burks (1979) and Hawkes et al. (1977b) for the U.S. Bureau of Mines provide the most complete description on the noise and vibration of percussion drill rods.The longitudinal and bending waves are the two most important types of elastic waves generated in drill rods. Among these, only the longitudinal waves contribute to the drilling rate. The bending waves are caused by non-centralized impacts, drill rod curvature and non-uniform bit/rock interface. Drill rod noise is generated by Poisson’s ratio expansions and contractions of the rod as the longitudinal waves travel up and down it and by transverse rod motions induced by bending waves. The radiation efficiency is much higher for bending waves than for longitudinal waves. Most of the impact energy is transformed into longitudinal waves, as expected for axial impacts. The evaluation of the relative contribution of longitudinal and bending waves to noise generation poses a very difficult problem for experimental, analytical and numerical approaches. It is, however, an important issue because the relative contribution of these two waves will guide future noise reduction efforts. It seems that very little can be done to reduce the noise radiation of the axial waves without affecting the drilling rate. The main difficulty that analytical and numerical approach-es face, in the evaluation of the relative contribution of the two waves, is that there is no adequate theory for predicting the bending vibrations from the factors that cause them. The experimental approach has, thus, been limited to test fixtures that do not adequately represent the boundary conditions, as well as by measurements obtained under real operating conditions from which it is difficult to establish the relative contribution of the two types of waves. For example, Hawkes and Burks (1979) and Hawkes et al. (1977b) used a test fixture with free-free boundary conditions and made no clear link with measurement under real operating conditions. Rather, they have based their discussion on a simple model. Many authors assume that fexural waves are the main noise source on drill rods. However, measurements have been somewhat contradictory and researchers are still unable to state with certainty that this is indeed the case (Lednik et al., 1988)."

Jan 1, 1997

By Franc R. Joubin

"Gold has been found in many parts of the Bridge River district of British Columbia; but it is from a relatively small area in the valley of Cadwallader creek that most production has come. The ore-bearing area measures 1/2 mile in width by 3 miles in length; and for convenience it is called the Cadwallader gold belt in this paper. In this belt are found the Bralorne and Pioneer mines and in addition several prospects under development.The gold of the Cadwallader gold belt occurs in quartz veins averaging about 3 feet in width and containing about ½ oz. of gold a ton. Except for a relatively small amount of silver, no other metals are produced from these veins. The ore-bearing veins occur in a variety of rocks. They occupy reverse faults and tension fractures belonging to a distinctive fracture system. Some of these structures are ore-bearing over lengths exceeding 5,000 feet and depths exceeding 3,700 feet. The production of the Bralorne mine (1932-1945) is 996,383 oz. gold and 190,709 oz. silver; that of the Pioneer mine (1930-1945) is 777,588 oz. gold and 135,698 oz. silver. These two mines have together distributed about $25,000,000 in dividends.The Bridge River district first attracted attention in 1863* when prospectors were attracted by its small but rich placer gold deposits. Most of the important lode deposits of the Cadwallader gold belt were discovered in 1897 (11). Many years of desultory development followed and it was not until 1928 and 1932 that the Pioneer and Bralorne mines, respectivdy, entered into profitable production."

Jan 1, 1954

By R. J. Young, S. J. Tennant, A. D. Drummond

"Gibraltar Mines is located on the western slope of Granite Mountain, 230 air miles north of Vancouver, B.C. and 38 miles north of Williams Lake, B.C. There are four mineable zones within the copper-molybdenite deposit: Gibraltar East, Gibraltar West, Pollyanna and Granite Lake. Open-pit reserves are 358 million tons which average 0.37% Cu and 0.016% MoS2 at a 0.25% Cu cut-off. The Granite Mountain pluton is one of the several Jurassic-Cretaceous intrusions which outcrop along the east side of the Fraser River fault system between Williams Lake and Prince George, B.C. The original Granite Mountain quartz diorite has been metamorphosed by a cataclastic deformation which foliated the rock on a regional scale. Attendant to the development of the foliation, the rock was saussuritized such that the present mineralogy is compatible with that of the greenschist facies. The presence of garnet-bearing assemblages is explained by a restricted increase in water pressure. Pre-mineral intrusive phases within the saussuritized quartz diorite are: (1) leucocratic quartz diorite, (2) aplite and (3) quartz-feldspar porphyry. A late chloritized hornblende dacite dyke is post-mineral. Quartz-feldspar porphyry and leucocratic quartz diorite are locally present on the inner sides of the Gibraltar East, Pollyanna and Granite Lake pits. Their presence suggests a core around which occurs an elliptically shaped sulphide-bearing stockwork. The stockwork, which comprises four ages of vein development, is imposed on and partly controlled by the regional foliation of the samssuritized quartz diorite."

Jan 1, 1973

By Parviz N. Farsangi, Ferri P. Hassani, Allen G. Hayward

"Kidd Creek Mines places approximately 10 000 tonnes of consolidated rockfill (CRF) daily. Consolidated rockfill comprises sized aggregate mixed with different ratios and amounts of binders. Consolidated rockfill is employed to simplify subsequent pillar recovery and provide improved passive/active ground support.The consolidated rockfill is designed to sustain not only the gravitational loading of the overlaying fill material, but also to some extent the dynamic loading applied during blasting of the adjacent stopes and/or pillars. This paper describes the steps taken to optimize the pre-sent fill system at Kidd Creek Mines.The emphasis is on four areas which have high saving potential: lower cost alternative binders, structural design, quality control measures, in-situ testing techniques for back analysis. A consolidated rockfill design optimization chart was developed from these investigations."

Jan 1, 1996

By H. R. Banks

SHORTLY after the commencement of operations at the Sullivan concentrator, the use of a pilot table was instituted in order to present a visual control of various products by showing the amount of galena still present in the tailing from several stages of flotation. Among the products so treated, the final tailing was later included. It was sratifying to note that very little free galena was escaping, but a fine streak o a whitish mineral appeared at the concentrate zone. This mineral was identified as cassiterite. The amount was small and the newly recognized component in an already complex ore was considered primarily as of academic interest. However, the problem of recovering a usable metal was intriguing and, as opportunity presented itself in temporary lulls in research on Sullivan and other ores, the concentration of tin was a useful &apos;bit of knitting&apos; to go on with. It was recognized from the start that the bulk of the mill tailing would have to be floated and the residue subjected to gravity treatment. Since one of the predominating features of Sullivan concentration operation has been the necessity of fine grinding, the problem of gravity concentration was thereby intensified. Several batch runs were made, and sufficient pulp was treated to produce about one ton of final tin concentrate assaying 67 percent tin. The overall recovery was under 30 percent and the estimated profit at full tonnage was only marginal. Testing was resumed several years later, when the price of tin again appeared attractive, in an attempt to develop a more compact plant with better recovery of tin. The weakness of the original plan of concentration was the large number of tables required to treat a feed so low in tin.

Jan 1, 1941

By J. Hall Carpenter

"Wet concentration has, in the history of ore dressing, been the primary treatment method following crushing, grinding and sizing, when these have been necessary. The evolution of new methods of gravity concentration has been comparatively slow.Today, the most significant and sophisticated of the new types of gravity concentrators is, no doubt, the cone concentrator developed by Ernst Reichert of Mineral Deposits Pty. Limited in Southport, Australia. These units have now had some years of use in the field, are becoming one of the standard tools of the industry and their metallurgical results, as outlined in this paper, are out-standing."

Jan 1, 1966

By J. P. Messervey

THE story of the efforts made by the Department of Mines of Nova Scotia in the search for and investigation of mineral resources for the Canadian war effort began in the spring of 1937. During the past five years, however, heavy enlistments in the Active Service Forces by employees of the mining industry of the Province caused a recession in the production of coal, salt, and other essential minerals required to keep industry rolling on a wartime basis. A marked increase was shown during the period in prospecting for &apos;strategic&apos; minerals, not only by individuals but also by some of the foremost mining companies. The Provincial Government offered encouragement in this field of endeavour by the enactment of legislation whereby the prospector was enabled to secure the maximum area of ground in a prospecting license at a minimum of cost. The labour requirements on the ground staked, however, remained unchanged. The Nova Scotia Department of Mines continued active investigation of minerals vital to the war effort. These included fluorspar, barytes, diatomite, limestone, and coal. Fundamental knowledge concerning the geology and mode of occurrence of these minerals was accumulated and extensive diamond drilling was carried out on the promising occurrences. Work in these fields is being continued.

Jan 1, 1945

By R. Bruce Graham

The formation, evolution and classification of peat bogs is discussed. Factors resulting in the internal and external morphological changes in a bog are described. The fibrous, absorptive and sterile properties of peat moss account for its widespread use in horticulture and related fields. These properties also account for its usefulness as a binder in pelletizing, as an insulating material in bat tons and in panel construction. Peat, the humijied product of peat moss is used in market gardening and sod growing. It is utilized in Europe as fuel. It is a source of activated carbon and gas. Potentially peat can be used to produce waxes, resins, tannins, cellulose, hemicellu/ ose, humic acids, lignin and hymatomelanic acid. At present other cheaper sources are available.

Jan 1, 1984

By V. Taylor

"THE petroleum industry in Canada has been experiencing considerable difficulty in filling its manpower requirements during the last few years, and because of the rapidly expanding nature of the industry it is concerned about the supply that will be available to fill the needs of the future. As the oil industry is one of the more technically oriented industries, the most acute problem exists primarily in the field of profession-al/technical personnel. This is particularly true in the production and exploration side of the business, because it employs the highest percentage of this type of personnel. Let me illustrate this by giving you some figures reported by the Alberta Bureau of Statistics as of December, 1965 -out of a total of 9,641 male employees engaged in oil producing and geological and geophysical operations in Alberta, 3,021, or 31 per cent, were classified as engineers, geologists, geophysicists, managers and other professional personnel. No figures are available for 1946 to make a direct comparison of the expansion of the industry over the past twenty 466 years, but it is doubtful whether more than 100 professional/technical people were engaged in producing in Alberta at that time"

Jan 1, 1967

By John Kruse, Sethu Raman, Dave Tenney

The Cullaton Lake B-Zone gold mine was the first gold producer in the Kaminak Subprovince of the Canadian Shield . Located approximately 650 km north of Thompson. Manitoba, the mine produced 77,783 ounces of gold and 5,564 ounces of sil ver from 251 ,236 tons of ore during 1981-84 period. The depos it is a small , structurally controlled , stratabound orebody in an Archean iron formation. Most gold occurs in sulphide and silicate fac ies. Based on new ev idence, the depos it is interpreted to have fo rmed by remobilization of syngenetic low-grade gold mineralization in the iron fo rmation in a favoura ble fold structure. The concept and methods developed at the mine have been successfull y applied in the discovery of new deposits in the area. One of the concepts. which link Archean and Proterozoic mineralization. may have wider applications in the search fo r gold deposi ts elsewhere in Canada .

Jan 1, 1986

By W. J. Wright

Summary Statement The following notes on the geology of the Grand Lake coalfield are intended to be introductory to a second paper being read at this meeting, which paper will describe the earlier and the more modern mining methods. The coal industry of the Grand Lake coalfield is centred chiefly within a three-mile radius of Minto, but minor operations are dotted over an area of approximately 50 square miles extending easterly to the vicinity of Chipman and Coal Creek (see Figure 1). The coal comes from one seam of Pennsylvanian age. The seam varies in thickness from 16 to 30 inches and lies almost horizontal at depths of 0 to 125 feet. It has been mined and prospected over an area of approximately 150 square miles, but in a portion of this area the commercial possibilities have been destroyed by erosion. The industry is the oldest of its kind in North America, but it did not at tract particular publicity until about 1914. Since that date, mining methods have improved and the output has rapidly increased until, in 1934, it amounted to 271,335 long tons, and furnished employment for about 1,000 men (1). Approximately 73 percent of this amount was produced by the Minto Coal Company, the Miramichi Lumber Company, the Avon Coal Company, and Welton and Henderson, and 25 per cent by the Rothwell Coal Company, Harvey Welton Limited, G. H. King, the Reade Construction Company, and the Newcastle Coal Company. The remainder was produced by J. W. Carter, G. D. Crossman, T. H. Swift, C. S. Yeamans, and several other small operators. The coal is won by underground mining, except in the case of the Reade Construction Company, and a minor operation by Ashfield and Pieton, who have employed open stripping. It is mined only as required to fill definite orders, and is loaded directly into cars for shipment. In 1934, the larger mines did not operate full time, and the production could easily have been increased if markets had been available. The coal is sold in four grades: screened or lump, run of mine, slack, and stripping. The chief market is with the railways and commercial plants, with a fair amount for domestic purposes.

Jan 1, 1935

By M. Sukhram, S. A. Argyropoulos

"In the aluminum and steel processing industries there is a need for velocity sensors to measure the flow characteristics of liquid metal. This paper will present a sensor and an inverse heat transfer technique to determine the direction of velocity in flowing liquid aluminum. Experimental research work with the sensor involving liquid aluminum was conducted, using the Revolving Liquid Metal Tank at the University of Toronto, which rotates 50 kg of liquid aluminum with velocities up to 0.35 m/s. Experimental data for various magnitude of velocity demonstrate that the sensor records different thermal profiles under different fluid flow conditions. Using the transient temperature information and the inverse technique, the direction of velocity of the molten aluminum flow field can be inferred. INTRODUCTIONOur research at the University of Toronto has focused on developing invasive sensors to determine the velocity of high temperature liquid metals. High temperature in this setting is defined at VALUES (in excess of 660 °C. The discussion which will persist in this manuscript involves detecting the direction of flow in liquid aluminum using an inverse heat transfer technique. We first reported on the sensor which is used in this article in the following two publications (Sukhram and Argyropoulos, 2011a; Sukhram and Argyropoulos, 2011b). The motivation to perform this research is due to the lack of sensors available to characterize the conditions within a high temperature liquid metal reactor/vessel. A report conducted by The Minerals Metals and Materials Society (TMS Energy 2011) has suggested that the introduction of sensors into molten metal processing environments has the potential to increase process efficiency up to 15%. Such sensors will aid in the understanding of high temperature liquid metal processing operations with the goal to implement more efficient process design and practice."

Jan 1, 2012

By Magdy Ibrahim

This paper presents experimental design and development of a low-cost remote sensing hardware designed to support automated site data acquisition for near real-time progress reporting of construction operations. The developed hardware utilizes open source microcontroller equipped with multiple sensors that include 3D accelerometer, GPS, Data logger and Bluetooth. The use of open source microcontroller makes the developed design cost effective; freeing it from the need for costly license fees. Its platform configuration is flexible; enabling the addition of temperature, weight and other sensors, Wi-Fi and Xbee capabilities to suit individual field applications. Pilot tests have been carried out in laboratory and outdoor environments. The results prove effectiveness and robustness of the developed configuration. The paper provides description of the individual components used in the development of this prototype hardware. It also describes the technical characteristics, capabilities and limitations of the developed hardware. The findings of comparison with alternative technologies used for outdoor tracking of construction operations are presented. The comparison is carried out with respect to range, cost and suitability for outdoor environment. The developed hardware is expected to support a wide range of applications including tracking of earthmoving operations, highway construction and onsite resources. As well, it is expected to enhance safety on construction jobsites.

Aug 1, 2013

By E. Goodwin

The mechanics of formation of wear-metal suspensions in lubricants is discussed, along with the relationship of the concentration of the metals and other particles to the wear of lubricated machinery parts. The importance of particle and suspension analysis of used lubricants in a preventative maintenance program is stressed, in particular with regard to mobile equipment in a mining operation.

Jan 1, 1978

By A. J. Ouellet, A. Coulombe, B. Salmon

The no. 7 vein system cuts the Ventures gabbro which has undergone folding and fracturing; the latter, in response to movement on the nearby Campbell Lake fault. It fills a shear fracture which pinches and swells in the upper mine levels but has a more uniform width in the lower levels. The best copper and gold grades in the upper levels occur in the widest parts of this structure. The vein is richer in quartz on upper mine levels and in carbonate on lower levels. The north wall of the vein is more affected by major and minor element wallrock alteration than the south wall. The isocumulative ci;rves for gold and copper show a direct correlation between the two metals in the upper levels and their increased concentration in the wider parts of the vein. Gold grade decreases in lower levels. A proposed structural model identifies the no. 3 and no. 7 veins as second order conjugate fractures, related to the Campbell Lake fault. The fractures pattern suggests that a conjugate system developed between these two parallel veins as a consequence of rock competence and a relatively low confining pressure.

Jan 1, 1984

By C-D. Johansson, B. Ögren, B. M. Ludvigsson, K-Å. Johansson, R. Lindh, G. Berg, M. Maliarik

This paper presents the High Current Density (HCD) Silver Electrorefining Process. A 25-year history of development of the silver electrorefining process as well as associated equipment is given. The process is simple and robust, but at the same time highly automated. With low operating costs and man power requirement it allows consistent production of 99.99 % quality cathode silver. The process ensures that no toxic gases are formed in the working environment. Silver Electrorefining is a heart of a Silver Refinery plant covering the complete range of processes from casting of silver Doré anodes to casting of the bars of refined silver or/and silver granulation. The process has been successfully applied at 11 installations world-wide with plant capacities ranging from 30 to 1500 tpa.

Jan 1, 2014

By William Ferguson, Claude Deveau, Wade Hazel, Stephen R. Young, Allen Lussier, Robert Copeland

"LocationSometimes known as the Bernie Lake mine, the mine is located about 180 km east-northeast of Winnipeg on the northwestern shore of Bernie Lake, close to the Nopiming Provincial Park and the Manitoba-Ontario boundary. The mine is accessed from Lac du Bonnet which is linked to the provincial road system.Brief Description of OperationTantalum Mining Corporation of Canada Ltd. operates an underground mine employing ramp access, room and pillar mining, and shaft hoisting for the production of tantalum, lithium and cesium minerals. Daily campaigned crushing of the tantalum and lithium ores supply separate concentration circuits. Tantalum recovery employs conventional gravity equipment together with recently developed centrifugal concentration methods. All tantalum concentrates go to Cabot Performance Materials for the production of tantalum chemicals and metal. Lithium minerals are recovered using heavy medium separation and silicate flotation to produce spodumene and montebrasite/amblygonite concentrates. The lithium concentrates are shipped worldwide for use in ceramics, specialty glass and mold powders. Cesium processing involves the dry grinding of pollucite as feed stock for the recently built on-site chemical plant dedicated to tl1e production of cesium formate, a high-density drilling fluid for use in the oil industry."

Jan 1, 2000

By C. E. Dowker

"IntroductionMechanization underground at the Buffalo Ankerite mine in Deloro township, Porcupine district, had reached a high level by 1944, both in equipment available, and in the use of this equipment, for all stoping operations. Power feed leyners and the latest type of stopers for drilling, slushers for moving ore and fill, and tugger hoists for all servicing, did much to halt rising stope costs, and in some cases decreased them. On the other hand, little beyond the use of mucking machines and power feed leyners had been adopted in the effort to reduce level development costs, or to increase the advance per man-shift.Faced with ever increasing level development costs, caused by rising prices of equipment and supplies, coupled with increasing wage demands for less physical effort, it was realized that more mechanization of development work was essential. The objectives of such further mechanization were:(1) Decreased development costs(2) Increased footage per man-shift(3) Less physical effort by development crews, with greater take-home pay (4) A more satisfied and stable labour force"

Jan 1, 1950

By R. F. Baxter, C. M. Read, R. I. McCulloch

"Globalization of the aluminium industry continues to increase the pace of change and the intensity of competition, while simultaneously, society demands better products, cleaner technologies and sustainable industries. Bechtel, a global engineering, construction and project management company, is not immune to either the opportunities or the challenges created by globalization. However, and not withstanding the challenges, for aluminium industry ""players"" with a true global perspective, globalization presents very real opportunities that may be leveraged to deliver value creating goods and services. The following paper will focus on the exploitation of one of the opportunities created by globalization in the Knowledge Management domain - the application of high level tools and methodologies to improve global delivery of greenfield and brownfield aluminium smelter construction projects. Specific examples will be presented of value driven solutions that were delivered at the early stages of project engineering."

Jan 1, 2006