Search Documents

By V. G. c Papangelakis, M. Huang

A conductivity cell, developed previously, was employed in an effort to investigate the inter-relation between electrical conductivity and acidity of sulphuric acid - metal sulphate solutions at high temperatures. The measured solutions include the H2SO4-H2O, MgSO4-H2O, H2SO4-MgSO4-H2O, H2SO4-MgSO4-Al2(SO4)3-H2O solutions. All solutions reported in this paper were measured from 15 to 250 °C at equilibrium vapour pressure. The maximum measured concentrations of H2SO4, MgSO4 and Al2(SO4)3 were 0.45 m, 0.30 m and 0.10 m, respectively. It was found that, from 15 to 250°C, there is a linear relationship between H2SO4 concentration and electrical conductivities for acid concentration up to 0.45 m. At 250 °C and constant H2SO4 concentration, the solution conductivity drops with the increase of MgSO4 concentration. Lt is suggested that this drop is caused by a decrease in the concentration of H. Finally, an empirical model was developed based on the available measurements. This model has been tested against real laterite leach solutions where sulphuric acid and metal sulphates are dominant electrolytes. The average difference between the estimate acid concentration from this model and the one from titration was less than 5%.

Jan 1, 2004

By B. Arlyuk

On the basis of research of relations among the market participants the analytical model has been created which connects the price of industrial good at stock exchange with volume of sales and the stock of the sellers and buyers, Also a model was developed for assessment of these parameters of the market status by the actually fixed stock exchange and general market indicators. The composition of these models made it possible to create reliable system of short-term price forecasting for commodities or base metals up to one quarter ahead. Imperfectability of creation a model for reliable price forecasting by purely statistic methods (by the "black box" principle) was shown. A model of price behavior qualitative forecasting till one quarter ahead has been developed, which determines the probability of reaching in future of the given level as well as of the price maximums and minimums, Optimal values of threshold probability were determined for forecasting the future price maximums and minimums securing the maximum profit from the forecasting system application for commercial activity. The developed system of forecasting was identified for primary aluminium at the period of 1990-2003. The system was tested daily during 20 months period for speculations on 3M primary aluminium forwards at London Metal Exchange with high commercial result.

Jan 1, 2004

By S. Suzuki, C. Tokoro, S. Owada, T. Sakakibara

Acid mine drainage (AMD) has been actively treated by neutralization from about 80 abandoned or closed mines in Japan. More efficient and cost effective treatment processes has been demanded for AMD due to the government investment of billions of yen every year to protect the environment from these discharges. In this study, quantitative modeling was conducted for actual AMD to predict pH or residual concentration of toxic elements after neutralization/co-precipitation process. Simple chemical equilibrium calculation was not adequate for quantitative prediction of pH after neutralization, because residual concentration of major elements of AMD, such as Fe or Si, could not be quantitatively calculated. When oxidation rate of Fe(II) to Fe(III) and precipitation rate of kaolinite were added to the model, quantitative prediction of pH and Fe or Si concentration was achieved. Surface complexation at the interface between hydroxide such as ferrihydrite or aluminum hydroxide and AMD was the most important mechanism for removal of dilute toxic ions. When surface complexation model at the interface of ferrihydrite was added to the model, residual As (V) and Pb (II) concentration after neutralization/coprecipitation process was successfully calculated. On the other hand, surface complezation model of aluminum hydroxide was also necessary for quantitative prediction of residual Zn(II) concentration after neutralization/co-precipitation process.

Jan 1, 2014

The control of AG mills fed by ores with harder and softer components can be challenging due to the sensitivity of the mill to the ratio of hard to soft components. The mills at LKAB?s iron ore operations are generally well controlled, but there are periods when the throughput falls off dramatically, due to a loss of mill filling. As the ore is upgraded in the sorting plant through magnetic separation prior to milling, this presents an opportunity to manipulate the feed blend in advance. In order to assess this opportunity, a fullscale mill charge was dumped and assayed by size to quantify the build-up of competent waste in the mills. This was supplemented by pilot and locked-cycle laboratory tests at a wide range of feed blends in order to facilitate the development of an appropriate multi-component AG mill model. This paper reports the experimental campaign requirements and methodologies, as well as the major outcomes from analysis and modelling exercises using the industrial, pilot and laboratory multi-component data.

Jan 1, 2012

By K. Oishi

We have developed a 76Cu-3Si-21Zn alloy "ECOBRASS®" containing no lead. When 3% Si is added to a 78Cu-22Zn alloy, kappa and gamma phases participate uniformly in the alpha matrix. When being machined, stress concentrates on these hard phases, namely kappa and gamma, and thereby lowering the required cutting force and yielding segmentalized chips without lubricant. Kappa and gamma phases transform into beta phase under high temperature, which makes it easier to extrude and/or forge the alloy. When 0.08% P and 50 ppm Zr are co-added, the grains of ECOBRASS® castings are refined significantly to become as small as several dozens of micrometers. The grain refinement by the co-addition of P and Zr improves castability, tensile strength and elongation of ECOBRASS® castings. Meanwhile, the lead leachate from an ECOBRASS® water meter, field-tested in pH 6.8 drinking water for one year, was less than 5 ppb without correction. No indication of dezincification corrosion was observed, either. ECOBRASS® is equally suitable for rods, forgings and castings, and makes it possible to produce a complete set of plumbing parts (valves, faucets, etc.) by its own. This way, not only improving recyclability, ECOBRASS® also realizes size and weight reduction due to its good corrosion resistance and high strength.

Jan 1, 2007

By A. Tabereaux

The reduction of perfluorocarbon (PFC) emissions from aluminum electrolytic cells is a key issue in reducing greenhouse gases at all aluminum smelters, The emission of tetrafluoromethane (CF4) and hexafluoroethane (C2F6) gases during anode effects at smelters can be calculated using two different methods; anode effect-minutes slope and anode effect overvoltage, This work demonstrates that the optimum method depends to a large extent on the type of anode effect kill algorithm utilized at each smelter, CF4 emissions vary widely from aluminum cells depending on the type of anode effect kill method utilized; fast, aggressive anode bridge movements vs. slower, moderate anode bridge movements.

Jan 1, 2005

By Lassi Klemettinen, Ari Jokilaakso, Dmitry Sukhomlinov, Pekka Taskinen

The solubilities and distributions of molybdenum and iridium in iron silicate slag and copper-iron mattes were studied using an equilibration-quenching technique and subsequent direct phase composition analyses by EPMA (Electron Probe X-ray Microanalysis) and LA-ICP-MS (Laser Ablation-Inductively Coupled Plasma-Mass Spectrometry). The equilibrations were carried out on a wide matte grade interval, ranging from 55 wt-% Cu to 75 wt-% Cu, in pSO2 = 0.1 atm at 1300°C. The results in equilibrium with a solid iridium-molybdenum alloy indicated an iridium solubility of 150–500 ppmw in the sulphide matte, depending on the matte grade, and a molybdenum solubility of 100–600 ppmw. Iridium was distributing predominantly in the sulphide matte with the distribution coefficient of 10+3 - +4 but molybdenum deported predominantly in the slag with Lm/s(Mo) = 0.02–0.1. The effects of alumina and lime additions in the smelting slag were also examined. INTRODUCTION Iridium is a highly siderophile element (HSE), which means that it is incompatible with the sulphide forming elements and possesses a small solubility in mattes, such as copper- and nickel-iron sulphide melts. Molybdenum behaves only modestly in that way (Walker & Li, 2008; Righter et al., 2017). They both are known to be trace elements accompanying copper and nickel sulphide ores. No solubility data, however, are available for them in copper-rich sulphide mattes. Geochemical data on the behaviour of Ir and Mo deal mostly with low-iron silicate systems, e.g. basaltic melts, and high-sulphur sulphide solutions and mattes (Ertel et al., 2008; Fonseca et al., 2007). They also indicate that Ir and Mo dissolve in silicate melts primarily as oxides and not as electrically neutral metal species. Most geological data of iridium focus on high-sulphur systems of the monosulphide composition and typically Fe-Ni mattes where copper is a trace element (Fleet et al., 1996; Sattari et al., 2002). Direct solubility measurements for mattes and iron-lean silicates have also been made using pure Ir or an Ir alloy as the saturation phase (Borisov & Palme, 2000; O’Neill & Eggins, 2002; Makovicky & Karup-Møller, 1999; Ertel et al., 2008; Mungall & Brenan, 2014). A recent summary about the solubilities of HSE’s in iron- and sulphur free silicates is available in Laurenz (2012). The thermodynamics of molybdenum partitioning between oxides and Fe-S-O melts was studied by Mengason et al. (2011). Their results indicate strong accumulation in the iron-rich sulphide in reducing conditions (pO2 = 10-9.6 atm in Ni-NiO equilibrium at 1050°C). Molybdenum dissolves in iron-lean silicate melts as MoO3 species in oxygen pressures above the Fe-FeO equilibrium and as MoO2 in more reducing conditions (Farges et al., 2006; Righter et al., 2017).

Jan 1, 2019

By H. Wotruba, L. von Ketelhodt, M. Kowalcyk, C. Kleine, M. Robben

Sensor-based sorting is a financially and technically viable technique that is operating with little or no water and relatively little power consumption. Sensor-based sorting has already proven its operational stability at two gold applications in South Africa. Sensor-based sorting cannot only turn waste dumps and diluted mining blocks into reserves. The implementation can also cause a decrease in specific operating costs of mill and mine when for example replacing selective mining by bulk mining methods with subsequent sorting. Successful installations, operational experience, test work data and flow sheet integration from mine-to-mill underline the impact and potential that sensor-based sorting can have on the gold mining and processing industry.

Jan 1, 2011

By L. Voisin, K. Yamaguchi, D. G. Mendoza, K. Ltagaki

The behavior of arsenic and antimony in the Cu-0 system was thermodynamically investigated to understand their elimination during a blister-making stage in copper smelting. Firstly, the phase relations in a miscibility gap composed of the liquid slag and copper phases in the Cu-0-As and Cu-0-Sb systems at 1523 K were established by a quenching technique. It was found that arsenic and antimony distributed preferentially into the slag phase in the miscibility gap. Secondly, the activities of arsenic and antimony in the miscibility gap of these systems were determined at 1523 K by using a double Knudsen cell - mass spectrometer method. It was clarified that the activity of arsenic in the copper and slag phases showed the negative deviation from ideality while that of antimony in the copper phase a slightly positive deviation. These data obtained in this study suggest a possibility to eliminate arsenic and antimony by means of over-blowing in a converter after discharging the slag.

Jan 1, 2007

By D. Bai, F. Hamad, S. Abraham

For the integrity of welded structures such as pipelines, the toughness of the heat-affected zones (HAZ) is an important property. This property is often specified in terms of Charpy V-notch (CVN) impact toughness and determined by the standard test method. An experimental study has been conducted in an industrial laboratory to measure the impact toughness of the coarse grain heat-affected zones (CGHAZ) of an X80 line pipe material. The field girth welding conditions in terms of heat input were simulated, together with special edge preparation to improve the targeted testing of the CGHAZ. The effect of toughness of the neighboring regions, in particular the weld metal, on measured impact toughness of the CGHAZ was investigated. The fracture paths of the CVN tested samples were examined by both optical and scanning electron microscopy. The deviation of segments of the fracture path into the weld metal was found to have a significant effect on the measured impact toughness of the CGHAZ.

Jan 1, 2005

By Dirige. A. P. E.

A study was conducted for an operating mine to determine the appropriateness of its tailings material to be used for the preparation of a low modulus, high density backfill. The research was initiated due to issues arising from increased observations of compressive failure of backfill placed in stopes and inconsistent backfill behaviour (i.e. increased backfill brittleness and modulus). Backfill materials investigated were classified tailings and de-slimed tailings. Characterization of the physical properties of the classified and de-slimed tailings materials was conducted to assess the effect that these material properties would have on the strength and deformation behaviour of high density backfill products made using them. Such behaviour was investigated to determine whether differences in tailings physical properties would influence the strength and modulus character of the backfill materials. Uniaxial (UCS) and consolidated-undrained triaxial compression strength tests were conducted to determine strength performance and deformation behaviour of backfill. This paper presents the results of the backfill material characterization study and how different particle size distributions affected the strength performance and deformation behaviour of the different backfill mixes. It also demonstrates how stress-strain curves generated from material strength tests were used to evaluate variation in high density backfill mix response when such materials were subjected to unconfined and confined (triaxial) compression loading.

Aug 1, 2013

By N. R. Andrade-Gonzalez

In this paper, the effect of magnesium and strontium additions on the heat treatment behaviour of cast A319,2 alloy was investigated, Permanent mold samples were heat treated at 495 °C for 4 and 24 h, then quenched in hot water and aged at 180 °C and 220 °C for different temperatures, It is found that multiple aging peaks are present in the age-hardening curves of Al-Si-Cu alloys, mainly when Mg and Mg-Sr are added, The results of electron probe microanalysis (EPMA) observations reveal that the age-hardening behaviour is related to the precipitation sequence of alloys, For the Al-Si-Cu alloy, the first aging peak is the result of the high-density GP zones, while the subsequent peaks arise from metastable phases, Obvious intervals during the transition from GP zones to metastable phases may be the main reason of the formation of multiple aging peaks, It is seen that addition of Mg (-0,40 wt %) leads to the precipitation of coarse Al5Mg8SioCu2 particles. When modifying the high Mg alloys, Cu-intermetallics segregate in areas away from the growing Al-Si eutectic regions, Modification with strontium retards the precipitation of the silicon out of the matrix.

Jan 1, 2005

By M. H. Colebrook

Nickel laterites contain about 70% of all continental or terrestrial nickel resources; therefore the recovery of nickel from lateritic ores has large economic significance. The processing of lateritic ores involves the preparation and movement of concentrated aqueous suspensions. However due to complex characteristics and non-Newtonian properties, ranging from shear-thinning to shear-thickening and from thixotropic to rheopectic, a basic understanding of the flow behaviour must be developed. This understanding will assist in the development of new plants and the operation of existing plants. The work in this paper involves the characterization of three ore types from the Vermelho ore deposit to categorize them as rheologically simple to complex. Rheological testing was also conducted on pure mineral samples that represent the main minerals in these samples. The results show that the rheological properties of the ore types can be related to the surface properties and physical characteristics of the main mineral constituents.

Jan 1, 2006

By R. E. Whitehead

"Abstract - Alkali-alumina and MgO-alumina plots are an effective instrument for displaying chemical and mineralogical compositions of altered and unaltered rhyolites and rhyodacites. They reveal that most supposedly unaltered rhyolites, apart from those of Cenozoic age, have undergone losses in Na2O and gains in K2O. The extreme loss of Na2O from highly altered rhyolites immediately adjacent to VMS deposits is strikingly illustrated by alkali-alumina plots. MgO/Al2O3 vs. K2O/Al2O3 diagrams display a strong negative correlation between MgO and K2O that results from the conversion of sericite to chlorite. A similar negative correlation between MgO and whole-rock d18O is apparent on plots of these two parameters. Alkali-alumina plots underscore problems in selecting appropriate precursor compositions required for mass-balance calculations. Molar ratio plots are a viable alternative to such calculations. Sommaire -Les diagrammes alcali-alumine et MgO-alumine constituent un instrument efficace pour la représentation des compositions chimiques et minéralogiques des rhyolites et rhyodacites altérées et fraîches.Ces diagrammes révèlent qu’à l'exception de celles d’âge Cénozoïque, la plupart des rhyolites qualifiées de fraîches ont subi une perte de Na2O et un gain de K2O. L’intense perte en Na2O que l’on note dans les rhyolites fortement altérées associées aux gîtes de type SMV est particulièrement bien mise en évidence par le diagramme alcali-alumine. Le diagramme MgO/Al2O3 vs. K2O/Al2O3 montre une forte corrélation inverse entre le MgO et le K2O due à la conversion de la séricite en chlorite. Une corrélation inverse analogue entre le MgO et le d18O de la roche totale s’observe sur un graphe comparant ces deux paramètres. L’usage du diagramme alcali-alumine fait ressortir combien il peut être difficile de choisir un précurseur de composition appropriée pour des calculs de balance de masse. Les diagrammes de rapport molaire constituent une alternative à de tels calculs."

Jan 1, 2006

By D. A. Beattie

Three novel dextrin polymers of varying functional group chemistry but similar molecular weight have been used to depress talc in single and mixed mineral studies. The mixed mineral system was a model sulphide ore consisting of talc, pentlandite, and chalcopyrite. Adsorption isotherms for the three polymers on both valuable and gangue mineral phases were determined to give initial clues as to the ability of the polymers to depress talc. Flotation testing revealed a distinct hierarchy of effectiveness of the polymers in the depression of talc in the single mineral system (MP Dextrin > CM Dextrin > Dextrin TYM), reflecting the observed adsorption affinity and adsorbed amount of the polymers on talc. However, a different order of effectiveness was observed for talc depression in the mixed mineral system (CM Dextrin > MP Dextrin > Dextrin TYM). Competition between the valuable and gangue mineral phases for uptake of MP Dextrin is responsible for its observed decrease in efficiency in mixed mineral flotation. All three polymers were found to be reasonably selective in their action, although at high dosages the polymers began to affect the flotation of the valuable minerals.

Jan 1, 2006

By Liu Liu

In the recent 10 years the rapid development of Chinese steel industry has attracted the attention of the world. The technological progress of converter steelmaking has played an important role in this process. First of all, slag splashing has been extensively adopted by Chinese steel companies in various sizes of converters from largest to smallest ones, and even including those using special hot metal containing V and Ti. Remarkable metallurgical results have been achieved. Up to now the average converter campaign life has reached nearly 10,000 heats, and the longest exceeds 30,000 heats in three melt shops. Based on this process, the long-life combined-blowing converter steelmaking technology has been developed. Slag splashing has been used to form a gas permeable "slag mushroom" on the top of bottom nozzles to protect the nozzles. In order to keep the effective bottom blowing, furnace bottom thickness control technique has been developed to prevent the furnace bottom growth. It makes the service life of bottom nozzle the same as the converter campaign life (average 10,000 heats and longest > 30,000 heats). The complete combined blowing was ensured through out the furnace campaign. Concentration product [C][0] is in the range of 0.0023 ~ 0.0030%, the T.Fe in the slag is lowered by 4 ~ 6%, and the [0] in steel is decreased by 100 ~ 250 ppm.

Jan 1, 2004

By S. Bozorgi, K. Anders

"The automotive applications of heat treatable AlCu cast alloys are designed for performance at high temperature, which can be improved using specially alloying element as well as different heat treatment. In this research work an effect of alloying element such as Cu, Ni and heat treatment on microstructures and mechanical properties of AlCu alloy were investigated using optical microscope (LIMI), scanning electronic microscope (SEM) equipped with energy dispersive X-ray detection (EDS), Differential scanning calorimetry (DSC) and mechanical testing. It was found that during solidification most of the elements Cu, Mg and Ni segregated at the grain boundaries in the form of Al2CuMg or Al7Cu4Ni and a very small part of Cu and Ni element dissolved in the FCC-Al matrix. The latter is not completely reclaimable for strengthening mechanisms in FCC-Al matrix in its as-cast state. The results of mechanical test show that yield strength and ultimate tensile strength increases after heat treatment significantly compared with the as-cast state. Furthermore the mechanical properties at elevates temperature (240°C) is higher with higher Cu+Ni+Si containing alloys compared with the less Cu+Ni+Si containing alloy.INTRODUCTION Due to the high strength-to-weight ratio, high strength and ductility at room- and elevated temperature, AlCuSi cast alloys are widely applied in the automotive industries specially for producing cylinder head and engine block, where modified alloys with enhanced metallurgical properties are always needed to satisfy the ever increasing demands for the applications. The AlCu based cast alloys can be strengthened by age hardening. The precipitation processes from which this hardening is derived can be attributed to the presence of selected trace element additions or micro alloying, which can change the process or kinetics of precipitation in age hardenable AlCu cast alloys (Polmear, 1998; Morris, 1991). Furthermore their strength is mainly controlled by the aging process through the precipitation and growth of very fine precipitates of the ?'-phase (a semi-coherent, metastable form of the equilibrium Al2Cu phase) from the Al and Cu Guinier-Preston (GP) zones. Several studies have shown that solute clustering occurs prior to the precipitation of GP zones, and this modifies both the nature and kinetics of the precipitation process. The typical size of GP zones is in the order of tens of nanometers, and the chemical composition of these precipitates is not easily measured, even with a typically analytical electron microscope (Polmear, 1989)."

Jan 1, 2018

By Xian Jian Guo, Lei Li, Hua Wang

Direct smelting of copper concentrate to blister copper has the advantages of energy saving and environmental protection. There has been a lot of effort invested in process development including test work and theoretic analysis in the past half century. However, the process has only been applied commercially to a few smelters that treat chalcocite types of copper concentrate. The main limitation to treating chalcopyrite types of copper concentrate is high copper content in smelting slag and low direct copper recovery. Thus intensive slag cleaning is needed. In this paper, the thermodynamic analysis was mainly carried out for the multiphase equilibrium of direct to blister copper smelting for both chalcopyrite and chalcocite concentrates. The practical problems in direct to blister copper smelting, which are mainly in copper content in slag, are clarified. The operational window of slag composition for different temperatures and oxygen partial pressure for the treatment of chalcocite type concentrates is identified. The process operation optimization for the blending of chalcocite, pyrite and chalcopyrite concentrates was done. INTRODUCTION The extractive metallurgy of copper can be divided into two broad groups of processes, namely, pyrometallurgy and hydrometallurgy, and the former is dominant. About 80% of copper in the world is produced by pyrometallurgy (Christopher et al., 2006). The first stage of conventional copper pyrometallurgy processing is to smelt copper concentrate to copper matte composed of FeS and Cu2S with slagging to remove a proportion of the iron (Gargul, Boryczko, & Bukowska, 2017). The smelting processes include bath and flash smelting. The second stage of the process is to convert copper matte to blister copper. In most cases, the copper matte is converted in Peirce Smith (P-S) converters, which are batch operations (Kubiszewski, 2015). The P-S converting can be divided into two periods, slagging and copper blowing. During slagging period, FeS in copper matte is oxidized to FeO, which reacts with silica flux forming slag. When the iron content in matte is less than 1%, copper begins to oxidize and reduce to form blister copper (Kucharski, Sak, Madej, Wędrychowicz, & Mróz, 2013).

Jan 1, 2019

By A. Koning, P. Lauzon

Pressure hydrometallurgy operations require vessels to be lined with an impermeable membrane for corrosion protection and one or more courses of refractory or ceramic brick. Examples of unit operations that utilize composite lining systems include pressure oxidation autoclaves, sulphide precipitation autoclaves, chloride leach reactors, flash vessels, cyclone separators, and direct contact condensers (heater vessels and quench vessels). The refractory lining must satisfy multiple requirements: it must thermally insulate the membrane from process fluid, be structurally stable, provide erosion resistance, be chemically compatible with process fluid, and provide an economic service life. New hydrometallurgical processes are pushing the pressure, and temperature, with each new generation of plants. A fundamental understanding of all factors affecting the mechanical stability of the lining system is essential as lining designs move further away from the industry's experience base. The impact of irreversible chemical swell, operating factors, design factors, and installation factors are presented based on modifications to the traditional one-dimensional mechanical stress model. A new stability criterion - that the brick lining remain in contact with the steel shell membrane - is presented. This new stability criterion imposes new restrictions on the lining design.The effect of geometry and adding additional degrees of freedom to the analysis is explored using two-dimensional and three-dimensional Finite Element Analysis (FEA). The effect of these additional degrees of freedom on the results of the one-dimensional model are discussed.

Jan 1, 2004

By Karl J. C. Harries

"3.1. INTRODUCTIONThis chapter discusses briefly the common law concepts of fiduciary relationship, constructive trust, and breach of confidence. Following a discussion of confidentiality agreements, the last section of the chapter compares and comments on two common law cases, the LAC Case and the Metalore Case. Civil law readers should not ignore this chapter or § 3.5. the comparison as, to a large extent, the concepts and comments are universal, even though the procedures for applying them may vary.1It should be appreciated that, regardless of the legal system, if the Court sees that a wrong has been done, it will attempt to right that wrong, either by awarding monetary damages against the wrong-doer to compensate the injured party or by attempting to make the injured party whole again by such means as negating an agreement (as in the Metalore Case) or returning property to a wronged party (as in the LAC Case). The methodology for accomplishing either of these results will vary with the jurisdiction, and the two are not mutually exclusive.These two Ontario cases have been chosen, not because they are the only ones available – they certainly are not – but because both are relatively well known within the minerals industry and they deal with problems that may face any explorationist (although it is to be hoped that the facts of the Metalore Case do not represent “normal” behaviour). Each judgment offers useful guidelines, as well as insight into a judge’s approach to problems, the type of information he expects to receive, how his mind works, and, particularly in the Court of Appeal judgment in the Metalore Case, how he might reason through and “justify” his decisions.3.2. SOME LEGAL CONCEPTS In order to appreciate some of the matters discussed in this chapter, it is necessary to have some idea of the common law considerations of fiduciary relationships, constructive trust, and breach of confidence."

Jan 1, 2003