Search Documents

By P. Hansman

"Place Dome Canada's Detour Lake Mine is a low-grade gold producer located in northeastern Ontario. Production is targeted for 2850 tonnes of ore per day. As reserves and mining areas continued to be found below and far to the west of the shaft (Fig. 1), it became necessary to review and upgrade the materials handling facilities. This paper deals with the selection, design and construction of an underground crusher and conveyor system capable of handling up to 450 tonnes per hour from the lowest existing level in the mine.BackgroundThe Detour Lake mine site is accessed via secondary Highway 652 which runs northeast out of Cochrane, Ontario. The road consists of 200 Ian of hard top followed by 100 Ian of well maintained gravel to the mine site. A 1500 m airstrip is maintained at the mine site for emergency use. Prior to 1991, the workforce was flown to and from the mine site. Crews were now bused to the site from Timmins. Remnants of a winter road exist to the southeast which at one time ended in La Sarre, Quebec. This was the route used to haul bulk items during the construction period and early production years.A town site has not been established at the site for the current operations. Instead, a rotational scheme is being utilized whereby most personnel will work seven days on site followed by seven days off site. For some employees, however, the work week is termed as a four/three schedule where they work 42 hours between Monday at 10:00 a.m. and Thursday at 4:00 p.m. with the following three days off. All surface employees and maintenance employees underground work 12-hour shifts. All underground employees work a lOV2-hour shift. Supervisors work a similar schedule as their crews, however, other staff may overlap their rotation during the week.A five-compartment shaft was sunk in 1984 from surface to the 610 m elevation. Shaft stations were established at the 120 m, 260 m, 360 m, 460 m, and 560 m levels. The cage compartment consists of a single deck, 4O-man cage in balance with a counterweight. The cage hoist is an Ingersoll-Rand 10H and is regulated to travel at 4.1 m/s. Two 9 t skips operate in balance at a travel speed of 7.1 mls. The skip hoist is a 3.05 m drum Nordberg. Both hoists are automated to function without a hoistman during normal skipping and cage service runs."

Jan 1, 1995

By Candido Bariáin

A new vapochromic material of formula [Au2Ag2(C6F5)4(bipy)2]n (bipy = 2,2´ bipyridine) has been developed and used for the detection of some volatile organic compounds as acetone either in vapour or in water solution. The material is presented in the form of powders which colour changes with acetone vapours turning from bright yellow in the absence of vapour to white in the presence of vapour. By using the sol-gel technique, the powder ? dispersed in tetraethyl orthosilicate- was easily deposited on optical fibres. In order to study experimentally the behaviour of this material for construction practical optical fibre sensors, a sol-gel material doped with the vapochromic material is deposited onto an extreme of a monomode fibre connected to a coupler. The behaviour of the material was studied for different wavelengths and concentrations of acetone vapours and acetone/water solutions. Changes up to 4dB in the reflected optical power were detected. Optical fibre sensors have many advantages over conventional ones, such as electromagnetic interference immunity, passivity behaviour, possibility of using multiplexation techniques, low weigh and little size, etc. Actually, there is an increasing interest in developing optical fibre sensor for vapour detection in the chemical industry and in fact many sensor had been developed [1]. Some are based on the deposition of a sol-gel-based material either over the core of an optical fibre [1] or onto the thinner zone of a biconically tapered optical fibre [2]. Others are based on Fabry-Perot interferometers [3]. Also there are sensors based on the reflection of the light on films, on the fluorescence of dye-doped polymer cladding in fibre, on colorimetric reagents in the core of a silica fibre or on surface plasmon [4]. The possible materials for the construction of such sensor should be colorimetric reagents able to change the colour or refractive index in the presence of same organic vapours. There are not many metallic complexes with these properties, although same interesting examples have been reported in the chemistry of palladium and platinum as [Pt(p-R-C6H4NC)4][Pd(CN)4] described by Nagel [5] and Mann [6], which reported the construction of some LEDs. We recently reported the preparation of a novel vapochromic material (Fig 1) [7] which can be used for the construction of optical fibre tapered environmental sensors [8,9] of vapour organic compounds (VOC´s). Also we reported other nickel and palladium derivatives which present this type of behaviour [10]

Oct 1, 2003

By A. Hutwalker, T. Plett

"Blast fumes are one of the major sources for NOx in underground mines. In 2016, the Occupational Exposure Limits for NOx in Germany were reduced by 90%. The task is to keep re-entry times after blasting at the present level and thereby ensure an economic operation of the mine. Measurements show that using ventilation solely is not sufficient. A new approach to reduce NOx from blast fumes is described. Laboratory experiments were performed and a reduction of NOx was observed. Measurements were conducted at an explosive factory’s testing facility and in an underground mine at blasting operations. INTRODUCTION Whether for production of ore or for drift development, the processes in an underground mine are always the same: 1) fracturing the rock, 2) loading the pile, 3) support the resulting cavity. The fracturing of the rock can be done mechanically, by cutting, for example by using continuous miners or tunnel boring machines, or by drilling and blasting. Drilling and blasting is more flexible than mechanical driving, as it can be used independently of the rock strength. Furthermore, this driving method allows a more flexible reaction to changes in geological and/or operational conditions. Thus, underground mining and blasting are almost inextricably linked with each other, and regardless of the size and level of technology of the mine, blasting is hardly avoidable. Depending on the mining method chosen and the existing framework conditions, such as the mechanical properties of the rock or the availability of machinery, blasting is an integral part of daily operations. Even in mines where blasting is not part of regular operations, it cannot be completely avoided. The blast fumes generated by the explosions are, in addition to diesel engine emissions, one of the two main sources of emissions of nitrous gases underground. Up to now, state of the art for dealing with blast fumes is ventilation. The fumes are diluted with fresh air and ventilated out of the mine. This treatment of blast fumes is more than sufficient with the former German Occupational Exposure Limits (OEL). The adaption of the OEL in Germany to the recommendations of the Committee on Occupational Exposure Limits (SCOEL), a committee of the European Commission, leads to big challenges for the mining industry in reducing the concentrations of these gases at the workplaces underground. On its meeting on May 2nd and 3rd 2016, the Committee on Hazardous Substances (Ausschuss für Gefahrstoffe, AGS), an advisory body of the German Federal Ministry of Labour and Social Affairs (BMAS), advised the BMAS to copy the OEL, as recommended by the SCOEL, to the Technical Rules for Hazardous Substances (TRGS 900). BMAS followed this advice, consequently the new OEL where published on November 4th 2016 and became part of the TRGS 900. Table 1 shows the former and new OEL for Germany. These new OEL became law after publishing, but two exceptions were made: For tunneling operations, they became law on October 31st 2017, for mining operations they will become law on October 31st 2021 (BAuA, 2004, 2016, 2017)."

Jan 1, 2019

By A. F. Gregory

"AbstractA resumé of aerial radiation survey studies performed by and for Eldorado Mining and Refining, Limited, since 1943 is presented. Flight tests were initiated in 1947 and were followed .by intensified use and study of Geiger counters and other radiation detectors. Development of an aerial scintillation counter began in 1948, but •a sensitive large crystal unit was not available for exploration purposes until 1950. Modifications of this unit have been used in all subsequent surveys.For the Eldorado detector, several limiting conditions were established for successful radioactivity detection, the most important being that natural vein exposures can only be assuredly detected .at distances less than 150 feet. Sedimentary and pegmatitic radioactive occurrences can be detected at much greater distances. A helicopter investigation technique appears to •have •a useful prospecting potential.IntroductionAerial radiation surveys were first proposed in the early 1940's. However, it was not until 1949 that airborne detectors were extensively used in the search for radioactive minerals. Eldorado has flown about 50,000 miles of exploration flights, exclusive of tests, using a variety of •detectors and aircraft. Considerable data have •been gathered for .the evaluation of the several techniques employed. Much of the early work was performed with the co-operation of the National Research Council of Canada ( 1). More recent work was done in conjunction with the Commercial Products Division of Atomic Energy of Canada, Limited. The Development Department of this latter corporation designed and built the scintillation counter used in recent Eldorado surveys."

Jan 1, 1955

By W. F. James

Introduction The season of 1927, from the point of view of mining development in the area west of Rouyn, was quite satisfactory. Serious prospecting and development' were undertaken over quite a large area, though the results in the matter of discovering new deposits of economic importance were rather disappointing. A large amount of systematic prospecting and geological mapping was carried out in the course of the work, and a considerable body of information collected. A widespread occurrence of sulphide mineralization was noted, chiefly near bodies of older gabbro. The frequent occurrence of pyrrhotite in or near which local concentrations of chalcopyrite were localized, lends support to the idea that such older sulphides as pyrite and pyrrhotite are relatively easy of replacement by chalcopyrite. From the prospector's viewpoint, areas near the contacts of masses of older gabbro are favourable prospecting ground, and pyrite and pyrrhotite mineralization are favourable indications that massive chalcopyrite may be found where it has completely replaced such sulphides. Pyrrhotite being magnetic is easily located, even where drift covered, by the use of such convenient instruments as the dip-needle and the magnetometer. It is suggested that pyrrhotite bodies, when located, be thoroughly prospected because of the fairly strong probability that they may show replacement by the more valuable chalcopyrite.

Jan 1, 1928

By J. Chenier, M. Boissoneault, D. Ducharme, R. Schonewille

The operation of Falconbridge's Sudbury nickel smelter has undergone significant change since the production was consolidated to a single electric furnace in 1994. In the late 1990's a capital program of about $100 MM (Cdn) was undertaken to expand and modernize the smelter. This project, known as Smelter 2000, was mainly driven by the need to process the new concentrate produced at Falconbridge's Raglan operation in northern Quebec. Included in the scope of the project was the installation of dry concentrate handling facilities, modifications to the roaster feed preparation system, installation of a matte granulation system and modification of one of the converters. Improvements to in-plant hygiene were also an important part of the Smelter 2000 project. Over the past 5 years much has been learned about the challenges in treating two significantly different concentrates. More recently, the introduction of a third concentrate from Falconbridge's new Montcalm operation near Timmins, Ontario has added another dimension to the operation. This paper will describe how the main challenges from the past 7 years have been overcome and discuss the path forward for the Sudbury Smelter Business Unit.

Jan 1, 2005

By E. Fiset, T. Hennebel, F. Verbruggen, A. Prévoteau, K. Rabaey

Arsenic (As), bismuth (Bi) and antimony (Sb) are known to affect the quality of copper deposits in copper electrowinning operations. The codeposition of As was previously believed to occur only at current densities far exceeding the range of typical current densities for copper electrowinning. In this study, we investigate the copper electrodeposition on different pretreated stainless steel (SS) substrates from bleed electrolyte in galvanostatic mode at –45 mA/cm². Scanning electron microscopy (SEM) micrographs illustrate that during the initial phases of copper nucleation and growth, the current density was locally increased due to the pretreatments. It was reasoned that the codepostion of As could possibly occur in normal electrowinning conditions, but the risk can be substantially reduced by good SS substrate handling and maintenance practices. INTRODUCTION The presence of As, Bi and Sb is known to have a deleterious effect on the copper cathode quality in copper electrowinnings (Hiskey & Maeda, 2003; Hoffmann, 2004; Xiao, Cao, Shen, & Volinsky, 2012; Xiao, Cao, Mao, Shen, & Ren, 2014; Jafari et al., 2017). They are known to influence both the chemical and physical quality of the copper as they can contaminate the copper (Jafari et al., 2017) and affect the copper deposit structure (Hiskey & Maeda, 2003; Kim, Kim, & Chung, 2009), which contributes to a degraded market value of the copper (Tuddenham, 1984). The incorporation mechanisms of these impurities are believed to occur mainly through slime inclusion (F. Xiao et al, 2012) and electrolyte inclusion (Hiskey & Maeda, 2003). Other studies suggested that codeposition of these impurities is possible by their standard reduction potential being close to the one of copper (Xiao et al, 2014). Hiskey and Maeda (2003) investigated the copper electrodeposition on a copper electrode substrate in Cu electrolytes with a Cu, H2SO4, As, Bi, Sb composition representative for commercial copper tankhouses. The combination of voltammographic techniques and Auger electron spectroscopy showed that As was the first impurity to be electrodeposited from this electrolyte, yet at potentials where the limiting current density of the copper electrodeposition reaction is exceeded. The copper tankhouses usually operate at a current density ratio of 0.3 to the limiting current density in order to achieve tolerable copper quality deposits. The codeposition of As could be considered impossible in this current density condition. However, it is known that during the initial phases of electrodeposition on foreign substrates, a substantial part of the reaction proceeds by growth of individual nuclei where the current density is locally high and diffusion limited (Radisic, Ross, & Searson, 2006). Furthermore, it was observed that copper nucleation on TiO substrates occurred preferentially in the scratched oxide free areas which could serve as parts with high localized current densities (Chang, Choe, & Lee, 2005).

Jan 1, 2019

By G. O. Crowell

This paper gives the history of the celestite deposit, now being mined by Kaiser Celestite Mining Ltd., near Sydney, Nova Scotia. Mining and milling procedures are covered, and the regional and local geology of the area are described, including the origin of the celestite.

Jan 1, 1971

By M. S. Badollet

"IntroductionAsbestos as received by the manufacturer of asbestos products is •in the •form of either crudes or milled fibres processed to different degrees of texture. Frequently, the manufacturer finds that l:ihe fibres as he buys them are not adaptable to his plant processes, and, therefore, it is necessary for him either to contact the mine supplying the material and request a specific texture for the :fibre or to reprocess the fibre in his own plant.When the mine or mill manager is requested to change his milling equipment to produce a special grade of fibre with a specific texture, he would like to comply. However, if he began to make special fibre grades for each customer, he would be in the position of constantly rearranging his milling technique, adding more equipment, or building a new mill. In the end, his mill would he producing hundreds of different fibre grades of varying degrees of texture, which is a difficult accomplishment if he desires to maintain any quantity of production."

Jan 1, 1950

By E. G. Gaylord

THE material improvements which have been made in the practice of exploiting oil and gas reservoirs in the United States during recent years may be attributed largely to: (1) The necessity for drilling deeper wells at costs not much greater than was formerly expended on shallower wells. (2) The necessity for producing oil at a lower cost per barrel. (3) A growing recognition of the importance of the nature of production practice upon ultimate yield of oil and gas. The first two of these factors result, to a large extent, from the fact that a greater proportion of new development has been deeper development, and these wells have been drilled in the face of progressively lower per well allowables. In California, for instance, maximum allowables have declined from 400 barrels per day in March, 1938, to 156 barrels per day in September, 1940, and during this same period some 125 wells were drilled to the deeper 10,000-foot producing horizons discovered during this time. The third item listed above results from our increasing knowledge of the basic factors which influence the amount of recovery we may expect from reservoirs. In addition to the longer-range planning now being undertaken by the more prudent operators, State proration and conservation laws have focused attention upon the importance of methods conducive to obtaining progressively greater quantities of the hydrocarbons in place. In a paper of this length it will be possible to discuss only a few of the recent advances. An effort has been made to select the more important of these and to indicate, where possible, the factors which have made these advances possible.

Jan 1, 1941

By M. H. Govett, G. J. S. Govett

"The current American ""energy crisis"", occurring in the midst of a global debate on the adequacy of mineral supplies to support present and projected levels of world consumption, has focused attention on Canada as a major world producer of minerals. Exports of minerals account for approximately one-third of Canadian foreign earnings; more than half of these exports are to the United States. Although the United States is a net importer of most industrially important metals, with the exception of nickel and zinc, only a small part of American mineral imports are from Canada; these imports are minerals for which geographical proximity and strategic considerations are important. In the short-term, Canada is more dependent on her exports to the U.S. than America is on imports from Canada. It is argued that Canada, far from indulging in economic nationalism to preserve her resources, should expand her exports while the markets are available."

Jan 1, 1973

By G. W. Poling, E. M. Coelho

"Sedimentary phosphate ores make up approximately 87% of the world's known reserves and are generally more difficult to beneficiate than igneous ores. In almost all cases, desliming prior to flotation represents the major source of losses. Laboratory studies of selective desliming of sedimentary ores are presented. Some fundamental studies with pure mineral systems are also discussed. Selective desliming, especially using selective flocculation, gave the best performance. Possible industrial applications of this selective flocculation-flotation procedure are discussed.IntroductionPhosphate ores are a major source of raw materials used in inorganic fertilizers (which supply nitrogen, phosphorus and potassium). Approximately 96% of the total world production of phosphate is utilized in the fertilizer industry. Reserves and production data are available in the literature. Today deposits with grades as low as 4% P2O5 are exploited in a few cases. However, in some northern African deposits, ore grades are still as high as 33 - 35% P2O5. Hout pointed out in 1982 that approximately 200 million tonnes of phosphate ore were upgraded by flotation only.Although there is a large number of phosphate minerals (over 300, only those in the apatite series are important ore minerals in phosphate ores. The most common member in this series is fluorapatite – Ca5(PO4)3F. However, in sedimentary phosphate rocks, many different substituents occur in the apatite lattice. Carbonate-fluorapatite (or francolite) is one of the most common names used to describe sedimentary apatites. It can be represented by the empirical formula:"

Jan 1, 1986

By William J. Davis, R. Blair Hrabi, Sally Pehrsson, Amelia V. Logan, Ross Sherlock

"Abstract - The Meadowbank gold deposits are hosted by a series of polydeformed and metamorphosed auriferous iron formations located in the Neoarchean Woodburn Lake group, western Churchill province, Nunavut. The supracrustal rocks in the Meadowbank area consist of a thick sequence of intermediate-composition volcanic rocks with intercalated iron formation, ultramafic volcanic rocks, and quartzite to quartz arenite. U-Pb geochronology gives an interpreted age of 2711 ± 3 Ma for the host strata at Meadowbank.The intermediate volcanic rocks are predominately volcaniclastic and have a geochemical composition that is consistent with an active continental margin setting. Iron formation deposition was coeval with the intermediate volcanism, as indicated by incorporation of volcanic detritus in the chemical precipitate. The geochemistry of the iron formation indicates that it precipitated from a fluid that at one time was at high temperature (>250°C), reducing, and likely acidic. Intercalated ultramafic rocks rarely show spinifex textures and have trace element ratios that are consistent with mantle plume-related undepleted mantle asthenosphere, likely recording episodic mantle upwelling associated with rifting in an active continental margin. The contact between the ultramafic volcanic rocks and the overlying quartz arenite is a disconformity marked by a quartz pebble conglomerate. However, similar geology on the structural hanging wall and footwall of the contact suggests that the conglomerate does not represent a significant hiatus in deposition, and is more likely a prograding terriginous siliciclastic unit.Three metamorphic events are recognized. The first, M1, is a cryptic greenschist facies event that is pre-D2. The second event, M2, is a mid-greenschist to amphibolite facies, syn-D2 event. M3 is the last event recognized, and is a post-tectonic greenschist facies event that is regional but inhomogeneous in extent, possibly reflecting thermal aureoles around post-tectonic 1.7 to 1.8 Ga Nueltin granites. The structural geology of the area is complex with four phases of deformation recognized, two of which had a significant effect on the geometry of the deposit. All of these regional events are interpreted as Paleoproterozoic in age. Relationships between deformation fabrics and mineralization, as well as the overall geometry of the mineralized envelopes, suggest that the deposit formed during syn- to late-D2. Superimposed on the mineralization are D4 structural elements that postdate gold mineralization.The main control on gold mineralization is replacement of magnetite by pyrrhotite and pyrite in high-strain corridors. The composition of amphiboles and chlorites associated with gold mineralization is remarkably consistent and shows no spatial or temporal variation, suggesting that it was buffered by the iron-rich nature of the host rocks. The bulk metasomatic effect on the intermediate volcanic rocks is characterized by the addition of K2O and the loss of CaO, Na2O, and MgO, with little variation in the total iron content. The elemental losses are likely the result of destruction of feldspars, stilpnomelane, and ferroactinolite, which are relatively common in the unmineralized rocks, and the formation of sericite, chlorite, and grunerite."

Jan 1, 2004

By R. B. Nourse, R. Hundermark, B. Masters, H. Joubert

The new 30 MVA slag cleaning furnace at Waterval Smelter, Rustenburg Platinum, South Africa, has been in operation since 10 March 2003. The furnace design and operation face a number of challenges including a wide variety of feed materials and resulting bath conditions. Furnace feed varies in combinations of granulated Waterval Ausmelt Converter Slag (WACS), hot fed Peirce-Smith converter slag, concentrate and reverts. Coke is added as reductant. The resulting slag composition varies considerably and regularly. For the case feeding WACS an almost pure fayalitic slag (60%+ FeO, 30%+ SiO2) with a very low viscosity results. Due to the widely varying slag conditions, including a superheated fayalitic slag with high fluidity, a robust sidewall design is required adjacent to the slag bath. For this reason the furnace sidewall is equipped with Pyromet's MAXICOOL® high intensity copper cooling system. The design and installation of the copper coolers as well as tap holes are discussed. To cope with the variation in bath conditions and high slag superheat (350°C when tapped at 1650°C), the copper coolers are capable of removing peak sidewall heat fluxes above 500 kW/m2. Feedback is included on the performance of the Pyromet MAXICOO® copper cooling system for the first two years of operation. The paper further includes an overview on the design and performance of the tap holes, furnace shell, furnace roof and copper slag spouts.

Jan 1, 2005

By Neil J. Sullivan, Goode. George E.

"The Adams mine, operated by Jones & Laughlin Mining Company, Ltd. and located near Kirkland Lake, Ontario, produces one million tons of iron ore pellets per year. This paper briefly describes the mining and concentrating operation and deals mainly with the operation of the pellet plant. The orebody consists of fine-grained magnetite and some hematite, with alternating layers of chert, and is mined by conventional open-pit methods. After crushing and grinding, the ore is concentrated by magnetic separation and flotation. Agglomeration is accomplished by the grate-kiln pelletizing process. The plant layout and general operation will be discussed in detail."

Jan 1, 1968

By Olivia Gamache

When working in remote and extreme environments, projects are faced with new challenges for engineering and project execution. This is heightened when also working in countries with a developing environmental regulatory framework, small skilled workforce available for recruitment, and minimal infrastructure such as power, roads, and water. There is an increasing realization that social and environmental aspects need to be built into project execution. Giving proper attention to these issues during project development and execution, and maximizing opportunities is an ongoing challenge.

May 1, 2013

By H. W. Fleming

In 1955, the results of a regional, geological interpretation of the northern portion of New Brunswick were used as a basis for selecting, for intensive exploration, three areas in which structural and stratigraphic conditions were believed to be favourable. Airborne electromagnetic work, in one of these areas, provided the justification for acquiring the Murray group. Even though the initial results were discouraging, this geological interpretation, combined with the fortuitous discovery of cop• per-bearing float, was sufficient reason for carrying out further work using geochemical methods. This work finally resulted in the discovery of the Murray massive-sulphide deposit, after about eighteen months of coordinated exploration on the property. While this deposit is a typical New Brunswick-type base-metal occurrence, extensive leaching has produced a fossil gossan that rendered it an elusive target for exploration techniques of limited penetration Full credit for localizing the target area is given to the geochemical techniques, but geophysical surveys were needed to provide the necessary

Jan 1, 1961

By Douglas A. Sloan

"Shutdowns and breakdowns that halt the process-flow of mine production are costly. Skilled maintenance tradesmen are scarce and expensive. The cost of maintenance or of production Joss from Jack of maintenance is significant and warrants considerable managerial attention.The most appropriate maintenance policy is dependent on an economic calculation. At one end of the spectrum is the policy of avoiding all breakdowns by replacement and preventive routines before failure, such as the airlines policy. At the other end of the spectrum is the policy of minimal routines and the acceptance of a breakdown as a prelude to a repair.The complexity and cost of maintenance warrants the appointment of a maintenance manager of senior status. Within the origination, there are a number of activities that can be specialized to improve effectiveness. Among these are the inspectors' activity, the establishment of improvement routines, the planning of repair tasks, maintenance engineering research and value analysis.The maintenance system is the mechanical aid to assist the staff in the implementation of the policy. It is designed to facilitate planning to make the best use of the resources. It provides information to identify areas where managerial action is required to make improvements. The job ticket is the basis of most systems."

Jan 1, 1970

By Richard W. Herzer

Introduction Thermal methods have been predominant in the metallurgy of the base-metals ever since the foundation of the industry thousands of years ago. Development in hydrometallurgy has been confined largely to the past six or seven decades. It was at first necessarily slow, then for a number of years rapid progress was made. At present, the uncertain state of the metal industry has curtailed research on the subject; however, in the next few years one may assuredly look forward to an ever increasing use of wet processes. Leaching methods have attained the dominant position in the case of certain metals, notably zinc. For others, they have made no headway at all. Copper presents a situation all its own. Due to the varied nature of its ores and to the large number of localities in which it is mined, a great number of processes have been developed, each suitable in its own particular field. In the case of this metal, therefore, it is more difficult to arrive at definite conclusions. It is the purpose of this paper, first, to review the outstanding developments of base-metal hydrometallurgy, and, secondly, to consider possible Canadian applications of some of the processes in use. The discussion will be confined to the three metals, zinc, lead, and copper, with particular reference to the last mentioned. Zinc General Note At present, zinc is produced by two principal processes, the older retort process and the electrolytic process. The latter is a development of the last twenty years and, judging by its present progress, bids fair eventually to supplant older methods in a large proportion of cases. It is certain, at least, that in the erection of a new plant, a hydrometallurgical process would be given the most serious consideration

Jan 1, 1934

By Amir Karami, Derek Kinakin, Catherine Schmid

The Mathews Stability Graph Method (Mathews et al., 1981) has been used by geotechnical engineers and mining engineers for over 40 years to estimate the performance of longhole open stopes in underground mines. The method is widely used and accepted by practitioners because it is relatively simple to use and can be modified to account for observed performance at a given mining operation. While the simplicity of the method increases its accessibility and utilization, it does not intrinsically account for variability in the various inputs, including rockmass quality, structure, stress, or stope orientation. This paper presents a modified approach for the Stability Graph Method, whereby Python scripts are used to process available geotechnical datasets and combine them with actual or potential distributions of Q parameters, induced stress, structure, or stope orientation. The resulting Stability Numbers are then plotted as a contoured distribution on the Stability Graph.  This allows the practitioner to quickly incorporate large datasets into the analyses, while also developing an understanding of how variability in rockmass quality, induced stress, structure, or stope orientation could affect stope stability.  This paper presents the fundamental principles of the Stability Graph method, the Python script and workflow, and two case studies to demonstrate the utility of the tool.

Oct 1, 2024