Search Documents

By M. Abdollahi, M. R. Khalesi, Y. Kianinia, A. Khodadadi Darban

High cyanide consumption during the processing of gold ores with high sulphide minerals can make the typical cyanidation uneconomic. Also cyanide is a toxic material and environmental concerns of cyanide compounds are serious. Optimization of cyanide consumption requires a methodology to estimate the amount of exposed cyanicides, the kinetic of their dissolution and estimation of formation of cyanide complexes which consume the free cyanide. In this paper, a methodology to estimate cyanide consumption by modeling the minerals and gold leaching kinetic based on a liberation model and speciation of all possible cyanide related species in the solution is presented. The results showed that this methodology could successfully estimate the cyanide consumption based on mineralogical data with very lower number of parameters compared to empirical models present in the literature, while it offers the prediction of formation of all cyanide complexes which could be used for optimization purposes.

Jan 1, 2017

By Hajime Miki, Gde Pandhe Wisnu Suyantara, Shigeto Kuroiwa, Eri Takida, Tsuyoshi Hirajima, Masashi Yamane, Yuji Imaizumi, Mitsuru Sawada, Keiko Sasaki

Selective flotation of molybdenite and chalcopyrite using various oxidation treatments (i.e., ozone treatment, hydrogen peroxide, and Fenton-like reagent) was studied in this work. It was found that ozone treatment produced a depressing effect on both minerals, resulting in a lower separation of both minerals. On the other hand, oxidation treatment using hydrogen peroxide (H2O2) and Fenton-like reagent could deliver selective oxidation on chalcopyrite surface and depress its floatability. However, bench-scale copper- molybdenum (Cu-Mo) flotation tests show that oxidation treatment using H2O2 required a higher dosage of H2O2 and a longer treatment time in order to deliver comparable flotation results to that of conventional Cu- Mo flotation using NaHS treatment. On the contrary, Fenton-like reagent could deliver selective Cu-Mo flotation results comparable to that of NaHS treatment at a lower dosage of H2O2 and a shorter conditioning time. Contact angle measurements and X-ray photoelectron spectroscopy (XPS) analysis were employed to understand the depressing mechanism of these oxidation treatments. It was found that the chalcopyrite surface covered by various oxidation products that render the surface hydrophilic. Meanwhile, the surface of molybdenite was slightly oxidized, making the surface remained hydrophobic. INTRODUCTION Molybdenite (MoS2), the main source of molybdenum, is associated with copper sulfide minerals, mainly chalcopyrite (CuFeS2), as a trace mineral. Molybdenite is a valuable mineral and plays an important role in making the copper-molybdenum (Cu-Mo) processing plant economically viable (Laskowski, Castro, & Ramos, 2013). Therefore, it is important to recover molybdenite efficiently and effectively and separate it from copper minerals. Conventional separation of copper and molybdenum minerals is usually carried out in selective Cu- Mo flotation process using a copper depressant (i.e., sodium hydrosulfide (NaHS), Noke’s reagent, or cyanides) (Ansari & Pawlik, 2007; Bulatovic, 2007). However, this process still suffers due to imperfect molybdenum recovery. Moreover, the copper depressants use in this process are toxic and harmful to the environment. As alternative, various methods have been developed to replace these toxic and hazardous depressants, for example, by synthesizing new non-toxic or low-toxic depressants or by using various oxidation methods such as sodium hypochlorite in an alkaline medium, manganese dioxide, oxygen, and plasma pre-treatment (United States Patent Office Patent No. US 2559104 A, 1951; Patent No. US2238250 A, 1941; Barzyk, Malysa, & Pomianowski, 1981; Hirajima et al., 2014). However, the oxidation phenomenon and mechanisms are still not clear since detailed surface analyses have not done and the plasma pre-treatment method is facing technical issues for industrial scale application.

Jan 1, 2019

By John A. Dresser

Seventy years ago a period of prospecting and mining activity began in the Eastern Townships of Quebec that seems to have been quite equal to that of recent years in the Rouyn field. In the following six or seven years a large amount of work was done over a widespread area. About fifty deposits gave some shipment of ore, from a few tons upwards, and as many as five hundred occurrences of copper were made known in the district by official records. Comparing the scale of commercial undertakings of that time and of the present day, these developments must have occupied quite as large a share of the capital and man-power of the Province as northern Quebec employs today. Working conditions at that time were not very favourable. The country was then only newly opened for settlement, and colonists were few and widely separated. Roads of the class built today were unknown. A single line of railway, the Grand Trunk, crossed the district from east to west. Colonization companies controlled large blocks of land on which they owned mining rights and usually reserved these rights in whole, or in part, when selling the lands. Then, as now, the precious metals belonged to the Crown. Yet the work was not without its successes. One of the first deposits discovered, the Acton, was, for a few years, one of the most profitable producing copper mines of its time. Another, the Eustis mine, has been in almost constant operation ever since, and is now vigorously pushing further development. At least two others, now quiescent, proved profitable operations, and several made considerable production. The manufacture of sulphuric acid in Canada was begun by the founder of the Nichols Company at Capelton, on a deposit that is now being re-developed, after a long and creditable career.

Jan 1, 1928

By C. H. Lee, T. T. Wang

"Exampling of the tunneling task in the Tsengwen Reservoir Transbasin Diversion (TRTD) in southern Taiwan, this study investigates the application of the Drilling Survey System (DRISS) in both Drilling and Blasting (D&B)- and Tunnel Boring Machine (TBM)-excavated sections. In the D&B section, a nonlinear relationship exists between drilling energy and uniaxial compressive strength of rock mass, in which a reasonable coefficient of determination can be analyzed statistically. Additionally, the DRISS accurately predicted an unfavorable section with a valuable position. The magnitude of uniaxial compressive strength back calculated using DRISS data also matches those acquired from geological investigations with different approaches. Study results indicate that the DRISS is an effective tool for fore-probing of both D&B- and TBM-excavated tunnels. INTRODUCTIONModern advancements in geological and geophysical investigations, and drilling techniques, have provided valuable information for detecting and interpreting geological conditions of rock tunnels with a resolution of several to ten of meters (Brückl et al., 2001, 2008, Lorang et al., 2005). Nevertheless, construction risks remain considerable during tunnel excavation, especially when a tunnel was excavated by a Tunnel Boring Machine (TBM). Predictions of the local fault, shear zone, and other minor geological features, which may cause moderate collapse or excessive deformation of rocks surrounding the tunnel, before tunnel excavation is highly desirable for high-quality tunnel construction and economically efficient project management.Rather than conventional geophysical prospection methodologies, which always favor large-scale investigation with moderate precision, this study focuses on the drilling method probing ahead of a tunnel. The goal of such an investigation is not only to prevent catastrophic collapse, but also to provide quantitative or semi-quantitative information for estimation of the mechanical parameters of rock mass.For the tunneling task in the Tsengwen Reservoir Transbasin Diversion (TRTD) in southern Taiwan, a drilling survey system is adopted for fore probing. Data collected from both drilling and blasting (D&B) and TBM-excavated sections are analyzed statistically and discussed. The applications of the Drilling Survey System (DRISS) are addressed accordingly."

Jan 1, 2015

By N. Schreithofer, M. Aspiala, R. Serna

The novel attachment timer apparatus presented in this paper serves as a diagnostic tool that allows the detection of changes in bubble-particle attachment probability and therefore floatability caused by alterations in the chemical environment and particle properties. The apparatus consists of six identical capillaries where bubbles with defined size are produced simultaneously in a measurement chamber. The bubbles at the capillary tips are placed in contact with the submerged particle bed for specific time periods, controlled with the help of automatic actuators. The advantage of the instrument is that hundreds of bubble-particle contacts can be measured automatically within a short time period. Microscopic pictures of each measured bubble are taken while recording the movement of the bubble before, during and after contact with the solid particles. The recorded pictures can be used to determine the actual bubble size and its corresponding deviation, and to detect the attachment of particles. The attached particles are collected in a detachable chamber for subsequent characterization. Furthermore, the device is portable and can be taken to the mineral processing plants for quick evaluation of particle-bubble attachment efficiency with particles and process water sampled directly from real processes.

Jan 1, 2017

By J. E. Gill

"THE YEAR 1959 appeared to be a good one in which to attempt a summary of progress in the location and study of sulphide deposits in Canada because a temporary surplus of metals caused prices to fall and many geologists who had been working like beavers were suddenly not so hard pressed. So it was •decided to arrange a Symposium. The response to the call for contributions was excellent and the result is the interesting collection of papers that follow.Activity in the search for massive sulphide deposits has never been as intense as in Canada since 1954. That was the year when the airborne electro-magnetometer first became generally available on a contract basis. These instruments work best on massive sulphide bodies, as do most of the ground electrical survey devices, so much of the new information relates to these. It was decided, therefore, to focus attention in the preparation of symposium papers on such masses. This served also to keep the survey within reasonable limits."

Jan 1, 1960

By Z. D. Hora

Air hough diatomite is known in many parrs of British Columbia, deposirs of mineable size have only been found in the area between Kam/oops and Quesnel in the sourh-cenrral parr of rhe province. Ar Quesnel, commercial producrion has continued since 1950 from diatomite lenses up ro 35m rhick. OCCURRENCES of diatomite are reported from many parts of British Columbia, but deposits of mineable size are known only from the area between Kamloops and Quesnel. Only Quesnel deposits have yet reached the production stage. Commercial production dates back to 1950, and up until 1979 approximately 22,700 tonnes of diatomite had been produced. Most extracted diatomite was processed until 1980 by Crownite Industrial Minerals Limited in Quesnel to produce an oil absorbent and animal bedding. Smaller shipments are used to make insulating bricks on the lower mainland. Deposits near Quesnel extend 40 km along the western bank of the Fraser River from Quesnel to Alexandria; most production has come from Lots o. 6132 and 906. Di atomite is present as discontinuous lenses up to 35 m thick. Diatomite beds Industrial Minerals in Canada are of Upper Miocene age and are overlain by plateau basalts. Diatomite consists almost exclusively of Melosira granulara diatoms that are usually very small and mixed with variable amounts of clay, ilt and volcanic ash. In recent years, extensive beds of diatomite were identified near the confluence of the Chilcotin and Fraser rivers. Diatomite in this locale is a part o f the Upper Miocene to Pliocene Chilcotin Group of sedimentary rocks that are overlain by olivine basalt and related luffs. A deposit near Red Lake is situated 50 km northwest of Kamloops. Diatomite beds occur in the Tranquille Series of Eocene age and are similar in composition to those in the Quesnel area. The Red Lake deposit is abo ut 4 m thick but its areal extent is only a few tens of hectares.

Jan 1, 1984

This paper details a brief history of the Australian gold industry from the 1980s gold boom to the present day, highlighting an industry characterised by innovation in plant design and junior companies prepared to "have a go", in contrast to the conservatism of many larger mining companies. Design flexibility, the innovation of new processes, the preparedness to exchange "process know how" and technology singularly differentiated the gold industry from other sectors during the 1980s to the present. The introduction of two stage crushing, semi autogenous (SAG) milling, and pebble crushing, mill innovations, carbon in pulp (CIP) and carbon in leach (CIL) and the North Kalgoorlie screen etc were all exciting changes in the industry.

Jan 1, 2011

By A. M. L. Cushing, S. Kelebek, A. Ghahreman

Iron sulfides are part of many ore deposits affecting flotation separation of non-ferrous base metals from them. Open-circuit potential (OCP), potentiodynamic polarization, and electrochemical impedance spectroscopy (EIS) measurements were carried out with pyrite and pyrrhotite electrodes to investigate their reactivity under various flotation conditions, which involved the use of TETA, SMBS, and their combination. TETA was found to adsorb on the electrode surfaces causing a significant increase in charge transfer resistance of the product formed, which was most significant at OCP. This effect is much less with SMBS, indicating its greater surface reactivity compared to TETA. The combined use of these reagents decreases charge transfer resistance to a greater degree than that experienced with their individual uses. Addition of Cu2+ as a potential activator to this system nearly eliminates the action of TETA on the electrode surface, which can be attributed to sequestration/chelate formation in liquid phase. The relative effects of these reagents on pyrrhotite electrode are similar to that of pyrite. The main difference between the pyrite and pyrrhotite electrodes is that the observed charge transfer resistance on the pyrrhotite surface with each reagent case is significantly lower by 3 to 4 fold. This is compatible with its anodic nature and ease of oxidation since the OCP value of pyrrhotite is lower than that of pyrite. Results are discussed in relation to flotation/depression behavior of these iron sulfide minerals in mineral separation processes.

Jan 1, 2017

By Bahaa Hussein

Considerable number of methods and procedures has been introduced for trending and progress reporting of engineering, procurement and construction projects. This paper introduces a novel method, designed to augment the set of indices for measuring schedule performance. The concept behind the developed method is to provide early warning by dynamically evaluating the schedule cumulative impact of construction projects. The proposed method is designed to highlight the gradual deterioration in schedule status resulting in a cumulative impact due to the aggregation of small delays encountered during the execution of non-critical activities, and can be used as an add-on utility to existing software systems that perform CPM scheduling. The proposed method is based on a developed formulation for quantification of the Schedule Compression Index, which takes into consideration the remaining project activities durations. The index is developed based on periodic comparisons of ?Current Schedules? and the project ?Baseline Schedule? using the summation of the remaining activities durations. A numerical example is presented to demonstrate the application and capabilities of the developed method. It is expected that the developed index together with other schedule performance indices would be of value to decision makers and members of project teams.

Aug 1, 2013

By K. Dinh

The Ground Penetrating Radar (GPR) has been studied for a long time as a non-destructive evaluation (NDE) technology for inspection of concrete structures. Currently, the most widely used technique for interpreting GPR data of concrete bridge decks is the one that based on the amplitudes measured at various interfaces such as asphalt-concrete, top rebar, or slab bottom. The assumption behind this technique is that a sound concrete deck should have the same reflection amplitude at these interfaces while any low number would indicate some sign of deterioration. Unfortunately, this assumption is not completely valid in most cases. As a consequence, the reported test results usually do not reflect real condition of concrete bridge decks in question. The main goal of this paper is therefore twofold: (1) to discuss the limitations of the amplitude analysis method, and (2) to propose a new model that interprets GPR data of concrete bridge decks. The model methodology is based on the comparison of GPR A-scans between two inspections, using the so-called correlation analysis. The results, indicated by the correlation coefficients, are then employed to develop a contour map that estimates different levels of deterioration. The model is then implemented to a case study in order to illustrate its methodology.

Aug 1, 2013

By E. Onal

Mining operators are faced with complex information delivered by technology-centric rather than user-centric systems. The ability to achieve high situation awareness (SA) in the face of this data overload is a key challenge for effective decision making and information exploitation. Incidents that result in loss of revenue and even life, and compromise safety that are attributed to human error are often the result of system designs that overload human cognitive capabilities. This paper focuses on defining SA as it relates to mining operations and presents methods for improving SA through a scientific approach for electric shovel operator user interface development.

Aug 1, 2013

By Tim Deans

This paper will address methods to manage hydraulic hose and coupling inventory so that parts will be available to build assemblies for the vast majority of equipment with as little inventory as possible. Topics also to be covered will include some basic hose assembly tagging techniques that will help keep equipment running by tracking problem hoses and building ?band aid? kits, having problem hoses premade in stock, and inventory usage tracking (one of the biggest problems for any inventory manager is knowing which couplings have been used so they can re-order). Cradle to grave tracking of hydraulic and industrial hoses insures reliable service of vehicles and ethical disposal of old hoses and couplings. With accountability for disposal of hose products that may contain chlorine (neoprene tube material in some hydraulic hoses) and carbon black that will be scrutinized more closely in the future, a proactive approach should be adopted in order to minimize maintenance facility problems.

Aug 1, 2013

By E. S. Moore

In order that a logical conclusion may be reached regarding the possible occurrence of commercial iron deposits in Canada it is necessary to consider some important producers found elsewhere on this continent. A study of such deposits reveals the fact tl:~at a number of distinct types are producing large tonnages of ore. These types may be classified according to origin and occurrence as follows: (1) Bedded sedimentary deposits. (2) Contact metamorphic deposits. (3) Residual ores. (4) Lenses in metamorphic rocks and m some cases of uncertain origin. In addition to the types listed there are other deposits which have contained or do contain considerable ore and they either have not been worked on a large scale or they have been nearly exhausted. These include the following types: (1) Magmatic segregations. These are mostly titaniferous magnetites. (2) Dikes of magnetite of igneous origin. (3) Bog and lake ores in glacial drift. (4) Black sand placers.

Jan 1, 1925

By J. E. Hawley, R. C. Hart

"The Preston East Dome gold mine is in the southeastern part of Porcupine district, Ontario, 5 miles southeast of Timmins, and immediately south of the property of Dome Mines, Limited.The claims now owned by this Company were originally staked in 1909. After the property had remained dormant for many years, the present Company was organized in 1936 to resume development operations. Two shafts had been sunk: at the time of the early work on the claims, but lateral work from these failed to reach the ore deposits. A successful diamond drilling campaign undertaken under the direction of D. G. H. Wright, however, was followed by the sinking of a five-compartment shaft arid the erection of a mill. From the start of operations to the end of 1944, 1,292,000 tons of ore averaging $11.60 in gold a ton have been mined.An outstanding feature in this mine is the occurrence of the major gold deposits in quartz porphyry intrusives, though minor deposits are also found in the adjacent Keewatin volcanics. Most of the ore occurs in fractures, but the filling was accompanied by varying degrees of replacement of schistose wall-rocks. The ore deposits may be classified as:"

Jan 1, 1954

By Y. Mudryk, D. Paudyal, K. A. Gschneidner, V. K. Pecharsky, M. Khan

"Rare earth intermetallic compounds are utilized commercially as magnetic and battery materials, electron gun electrodes, etc. Several of these intermetallics will be briefly discussed. There are many other rare earth intermetallic compounds which are not utilized industrially but have unusual properties which are of fundamental interest and may have future technological applications. Several of these materials are discussed as well.INTRODUCTIONTens of thousands of rare earth intermetallic compounds exist, but physical properties (primarily their magnetic behaviors), other than their crystal structures have been measured for only a small percentage of these materials. Among these are the commercially important compounds: Nd2Fe14B, and the SmCo5 – Sm2Co17 family – well known high strength permanent magnets; (Tb0.3Dy0.7)Fe2, Terfenol-D, a giant magnetostrictive material; LaNi5Hx a critical component of the rechargeable Ni metal hydride batteries; and LaB6 an electron emitter. There are, however, many other intermetallic compounds which are not utilized industrially, but none-the-less, exhibit interesting, and sometimes, exotic physical properties which are of fundamental interest and may have some future technological significance. These include: the giant magnetocaloric effect compounds Gd5Si2Ge2 and La(Fe13-xSix)Hy; the RCu and RAg families of ductile intermetallics; the mixed intra-lanthanide (R,R')Al2 compounds in which magnetic transitions disappear and reappear as one R is substituted for by R'; and GdNi which exhibits large dilations along two crystallographic directions and a larger contraction in the third direction at the Curie temperature resulting in zero volume change as GdNi orders magnetically via a second order phase transition.COMMERCIALLY IMPORTANT INTERMETALLICSNdFeB Permanent MagnetsThe Nd2Fe14B permanent magnets were discovered in 1984 independently in the USA and Japan. It is a ferromagnet and with proper heat treatment and processing Nd2Fe14B is the strongest near room temperature permanent magnetic material known today. This intermetallic compound is utilized as a permanent magnet in many applications, such as electric motors (e.g. the modern automobile contains up to 35 electric motors), spindles for computer hard disc drives, microphones and speaker magnets for cell phones and other audio equipment, direct drive wind turbines, actuators, and Magnetic Resonance Imaging (MRI) units. There are two kinds of NdFeB permanent magnets – bonded and sintered. The bonded magnets have a lower magnetic strength than the sintered magnet. The highest strength magnets are obtained by small substitutions of Dy (up to a maximum of 10%) for Nd, because Dy can significantly increase the coercivity and thus the energy product (a measure of the magnetic strength or hardness). The bonded magnets account for about 12% of the NdFeB market (~82 metric kt per year, containing ~20 kt/a of Nd). The NdFeB permanent magnet market is growing at a rate of about 15% per year. (Burzo & Kirchmayr, 1989; Kobayashi & Hirosawa, 2001; Coey, 2011)."

Jan 1, 2012

By K. Shen, A. J. Sinclair, N. Champigny

"Fluid inclusion studies from the Cinola deposit indicate low salinities and low C01 contents of the ore fluid. This supports a suggestion that the mineralizing fluids originated from pore water in the fluviatile host rock (mid-Miocene Skonun Formation). Bimodal distribution of filling temperatures suggests the existence of at least two temperature regimes centred on 160°C and 270°C during mineral deposition. Independent age and stratigraphic evidence indicates that depth of mineralization is between 1.1 and 1. 8 km, corresponding to a hydrostatic load of between 110 and 170 bars.RESUMELes donnees sur les inclusions fluides du gisement Cinola indiquent de basses salinites et basses teneurs en C01 . Ceci confirme que les fluides mineralisants ont ete derives de l'eau interstitielle prise dans les sedimentsfluviatiles hates. La distribution bimodale des temperatures d'homogenisation implique !'existence de deux regimes de temperature concentrees vers 160°C et 270°C pendant Ia mineralisation. La profondeur alaquelle le gisement s'est forme est evaluee d'etre entre 1.1 et 1.8 km a partir d'informations stratigraphiques independantes: ceci correspond a des pressions hydrostatiques de 110 a 170 bars."

Jan 1, 1982

By Ming’an Wei, Qifu Duan, Jianmin Wu, Lusheng Zhou, HMR Group Limited / HMR Technology Canada Ltd., Wenjian Wu

"The development and industrial applications of magnetic liners have been around for decades. A Swedish company Skega first introduced rubber magnetic liners, and then followed by the Chinese invention of metal magnetic liners. Traditionally, both liners were used in secondary ball mills and regrind ball mills for industrial applications, especially for ores containing magnetic materials. Mostly steel balls or equivalent forged steel balls, usually below 60 mm in diameter, were used as grinding media. With the development of mineral resources over the years, SAG mills and larger ball mills have become the dominating components for comminution circuit design. Due to the development of larger diameter ball mills and thus larger ball charge diameter (up to 80mm) especially in non-ferrous metal mining operations, the application of magnetic liners have been very limited. Based on “Magnetism theory” and the development of new materials, the HMR Group Limited has been conducting researches on examining the structures of magnetic liners, associated materials and magnetic circuits which led to the invention of the Nano Alloy Steel Magnetic Liner (NSML). Recently, NSML had a successful application in a 5.5 m diameter × 6.5 m ball mill at the Erdenet Copper Mine in Mongolia. The NSML successfully handled a ball size up of to 80 mm, while achieving a service life of nearly 24 months, which is almost 3 times wear life of the original manganese steel liners.INTRODUCTIONDuring the development and utilization of mineral resources, mineral processing is an indispensably operation. The effective separation of various useful minerals depends on sufficient monomer dissociation of minerals in the ores. The crushing and grinding operation is prior operation of mineral processing. Ball mills are used in different concentrators. As the main consumption parts of mill, liners have been studied constantly. As a new kind of liners, magnetic liners besides can meet the requirement of production, and also have characteristics with maintenance-free, saving energy and increasing efficiency. So the magnetic liners are worth to be spread and applied world widely."

Jan 1, 2016

By A. Pawelczyk, D. Hreniak, E. Zych, W. Strek, K. Grabas, A. Ostrowski

"Mongolia is a country rich in rare earth resources. In the experiments carried out samples of the Mongolian ore were processed to obtain a lanthanide concentrate. The concentrate underwent hydrometallurgical processing. At the same time radioactive elements were removed. The lanthanides were obtained in the form of hydroxides that were further processed in order to get concentrated products. As a result cerium, lanthanum and neodymium-praseodymium concentrates were separated in the process. Also a concentrate of remaining elements: samarium, europium, gadolinium, terbium, dysprosium, holmium and erbium was obtained. INTRODUCTIONAccording to the assessment of the US Geological Survey, Mongolia possesses 16.77 % of the world total rare earth (RE) resources (Daly, 2011); that is the second largest RE reserve in the world, estimated to be 31 million tonnes in terms of rare earth oxides (REO). In the face of Chinese RE trade restrictions, Mongolia emerged as an important economical partner in mining and exploitation of these critical raw materials. This country is recognized as having more than five large RE deposits in the southern provinces. The most important are Lugeengol (Lugin Gol), Mushgia Khudag, Khotgor and Khalzan Buregtei (Eurasia, 2010). The Mongolian government has taken measures to facilitate western investments, nevertheless the country is economically dependent on China, the basic trading partner, particularly where exports are concerned.In the late 1970s Hydromet Kowary Enterprise, Poland, took up, along with the Wroclaw University of Technology, research and technological study on lanthanides recovery from raw materials of Vietnamese and Mongolian origin and from Indian monazite sands (Kowalczyk, 1990; Kowalczyk & Mazanek, 1987; 1990). For that purpose, a rare earth processing plant had been constructed with the capacity of about 10 t/year of hydroxide concentrate. The facility included several technological operations like grinding, flotation, hydroxide concentrate production in the hydrometallurgical processing, particular RE separation, and production of commercial products in form of CeO2, La2O3, Nd2O3, Pr2O3, and misch metal. Additionally work had been carried out in Kowary on the manufacture of yttrium and europium oxides of high purity, which were intended for color TV picture tube production in Poland."

Jan 1, 2012

By R. L. Bruening, L. Navarro, Izatt. S. R., R. Adiga, R. M. Izatt, N. E. Izatt, A. Sharma, N. R. Patel, B. V. Rao

Bismuth is a notorious contaminant in the electrolytic refining of Cu that can cause cathodes to fail to meet ASTM International standards and not be suitable for use in Cu rod and other downstream products. Bismuth can significantly decrease electrical conductivity, decrease the mechanical strength of the annealed wire, retard recrystallization, and sometimes induce hot shortness during the hot rolling process in the production of rod. As a result, the control of Bi in the refinery tankhouse must be carefully managed. This paper describes how SuperLig® Molecular Recognition Technology (MRT) is being used for Bi removal at the Birla Copper Dahej Copper refinery. The operation of the SuperLig® MRT Bi removal plant is described and data on Bi removal efficiency are presented. INTRODUCTION Hindalco’s Cu division, Birla Copper, operates one of the largest Cu refineries in the world at Dahej, Gujarat; India. The main feed for this refinery is produced at the company’s smelter. Due to its massive production capacity, this operation mainly relies on imported Cu concentrates resulting in a variety of metals being carried out as impurities in the Cu anodes because pyrometallurgical technologies alone are not enough to remove them to the extent required. Metal impurities found in Cu ores include Fe, Zn, As, Pb, Bi, and Sb. During electrorefining, less noble metals dissolve in the electrolyte gradually increasing their concentrations creating the need for electrolyte control mechanisms that remove these impurities with varying degrees of success (Wang, 2004; Navarro et al., 2013.) Bismuth is one of the most significant impurities in a Cu refinery because it has the lowest ASTM product specification. This situation is critical because the Bi potential is very close to that of Cu making it possible to plate in the Cu cathode directly. Also, Bi can precipitate at high concentrations causing floating slimes and reduction of current efficiency (Ballinas, San Miguel, Munoz, & Gyves, 2003). Production of high purity cathodes from feed stock containing a diverse range of metal impurities becomes a major challenge in the refining of Cu (Izatt et al., 2015). In this work, the purification strategy followed by Birla Copper for the removal of Bi using a separation process based on MRT is presented, outlining the loading and stripping performance of SuperLig®83 and the benefits of using MRT over other lower selectivity methods where hazardous materials are produced instead of high purity products.

Jan 1, 2019