Search Documents

By F. D. Everett

The Federal Bureau of Mines reviewed the status of tungsten deposits of Utah in 1959. Industrial requirements of tungsten during emergencies have exceeded the domestic supply, and a knowledge of the sources of this strategic element may be helpful in the future. Tungsten occurs as the mineral scheelite in deposits that have been developed or explored on approximately 60 properties in 10 of the Great Basin ranges of Utah, none of which were being worked in 1957-59. Ores from most of the productive areas are similar in that they are contained in tactite deposits on or near the contact of calcareous and acidic intrusive rocks. The tactite ores consist predominantly of the silicate minerals garnet, epidote, and diopside and the carbonate rocks limestone or dolomite. Scheelite, where present, is disseminated irregularly in the tactite. Tungsten ores from Utah mainly have been produced from small deposits worked in World Wars I and II and the Korean campaign. The ores were either hand sorted to a grade ranging from 0.5 to 1.0 percent tungsten trioxide (W03) or were beneficiated in small mills to higher grade concentrates. The largest reserve appears to be in the area of the Notch Peak intrusive in the House Range, Millard County. A large part of the reserve in the House Range is mineralized tactite containing 0.2 to 0.3 percent W03. Research on flotation by the Bureau of Mines has indicated a method of concentrating scheelite in tactite ores that average 0.25 percent W03, with at least 85 percent recovery. The concentrate assays more than 5 percent W03 and can be processed into artificial scheelite ready for industrial use.

Jan 1, 1961

By James M. Spear

Sample results suggest the only mineral resources in the study areas are placer gold deposits along the South Fork Kern River in the Woodpecker RARE II unit (fig. 1). These deposits, in Rockhouse Basin, total 4.5 Figure 1.--NEAR HERE. million cu yds (3.4 million cu m) of indicated subeconomic gold resources in four deposits of "older" gravel. Gold value in samples averages $0.36 per cu yd ($0.47 par cu m) and is as much as $4.44 per cu yd 1/. Cost of mining the gravel and recovering the placer gold is estimated to be more than $2 per cu yd ($2.62 per cu m) for a deposit of this size and type. Additional inferred subeconomic placer gold resources with similar grade probably occur in four other deposits of "older" gravel on which no mining claims were located. Placer gold occurrences on upper Trout Creek contain gold worth as much as $4.50 per cu yd ($5.88 per cu m) 1/. Average grade is much lower, and only about 1,000 cu yds remain (760 cu m). These occurrences do not constitute a resource, but may attract hobbyists not dependent upon making a profit.

Jan 1, 1982

By James J. Dowd

The investigation to evaluate the reserves of coking coal in the United States suitable for the manufacture of metallurgical coke is being made by the Bureau of Mines in three parts: (1) To estimate known (measured plus indicated) recoverable reserves of all coking coal; (2) to upgrade marginal coals through effective preparation; and (3) to study the carbonizing properties of coals and coal blends not now widely used for metallurgical coke making. This is the sixth of a series of reports giving the results of studies by counties under part (1) of the investigation. (See appendix.) This report covers Fayette County, Pa., which comprises the Uniontown and parts of the Brownsville, Connellsville, Donegal, Waynesburg, Masontown, and Confluence, Pa., Morgantown and Bruceton, W. Va., and Accident, Md., quadrangles. (See fig. 1.) A short resume of the chemical and carbonizing properties of the coals ar.9 included. Data on the coal beds in this county were obtained from mining companies, land companies, individual landowners, and other sources of authentic information.

Jan 1, 1951

By William L. Rice

This Bureau of Mines Open Pile Report on cobalt is one of a series of minerals availability commodity deposit abstracts. Nonconfidential information from the Minerals Availability Program data base covering domestic and foreign cobalt properties and deposits has been abstracted for use in his report. Abstracts include applicable data on location, published reserves and resources, geology, mine and beneficiation systems, and operation information.

Jan 1, 2011

By Eric H. Brown

One of the best methods by which the results of accident-prevention work can be measured for any particular period is to keep an accurate record of the accident experience, which may then also be compared with the experience of others. The purpose of this report is to compare records of the salt-mining companies operating in Louisiana, and their assistance in making available their accident records is gratefully acknowledged. PRODUCTION Four companies produce salt in Louisiana -Avery Salt Co., Avery Island; Jefferson Island Salt Mining Co., Jefferson Island; Myles Salt Co., Weeks; and Carey Salt Co., Winnfield. Three of these companies operate within 30 miles of each other in the southern part of the State, and the other operates in the central part.

Jan 1, 1938

By Deno M. Pappas

This report presents results of a U.S. Bureau of Mines study of longwall gob material. The objective of this work was to determine material stiffness properties of the gob for use in numerical models of rock mass response to longwall mining, Photographs of actual mine gob were digitized to obtain approximate particle size gradations of gob material. The gradation curve was shifted down to a laboratory scale, and 20 uniaxial compression tests were conducted. Varying the maximum particle size was not found to affect the stress-strain behavior, but changing the gradation appeared to influence the stress-strain behavior. The stress-strain relationship of the simulated gob material was nonlinear, the stress-secant-modulus relationship was approximately linear, and the stress-tangent-modulus relationship was approximately a second-order polynomial function. Equations were generated from these curves, providing numerical modelers with a means to estimate gob moduli based on the stress level. In addition, the experimental data were statistically evaluated using multiple regression analyses, producing a series of equations to predict the secant and tangent moduli from the given stress level, bulking factor, rock strength, and thickness-to-width shape ratio of the particles.

Jan 1, 2010

By R. S. Dean

[Methods s of preparing the manganese metal that has been used in chemical and metallurgical investigations have passed through a cycle. Most of the investigations made e before the turn of the century, used Moissan's pyrophoric man manganese.3/ This material was made b; electrolysis into a mercury cathode and distillation in vacuo. The material was essentially pure, and investigations in which it was employed (with proper precautions against oxidation) led to accurate results on tie intrinsic behavior of metallic manganese.]

Jan 1, 1941

By C. W. Morris

This Final Report describes the major technical activities that were accomplished to produce a comprehensive continuous miner training system (CMTS) for coal industry utilization. The primary product of this program was a continuous miner part-task trainer. It is composed of an interactive computer graphics system combined with the operating controls of a continuous mining machine mounted in a simulated cab. The cab contains an audio system for reproducing continuous miner operational sounds. The trainer is supplemented with a complete set of cognitive materials that provide instruction in the operation, safety and health of continuous miner operations. A complete summary of the field test and evaluation of the CMTS is provided along with a set of recommendations for further training program refinements, expansions, and utilization.

Jan 1, 1982

By K. M. Connor, O&apos

Variations in overburden geology must be considered in applying subsidence prediction methodologies developed by the U.S. Bureau of Mines (USBM). To characterize rock mass overlying high-extraction coal mines, the USBM utilizes a computer spreadsheet program and modified Rock Mass Rating (RMR) system. The spreadsheet calculates an RMR based on a bed's engineering properties determined from core logs and laboratory tests. An in situ deformation modulus and a bending stiffness are computed for each bed. Stiffness-versus-depth plots identify groups of beds with similar stiffness. Large variations in stiffness between adjacent beds are considered significant horizontal discontinuities where slip is likely. Time domain reflectometry (TDR) is used to verify this hypothesis by measuring shear displacement along such discontinuities. A model of the overburden is built by assuming that a near-surface laminated beam exists above a transition zone in which large plastic slip occurs along horizontal discontinuities. Increasingly thicker groups of beds are modeled to determine the most probable beam thickness based on a comparison with measured deflection profiles. The inverse of maximum beam deflection is an index parameter known as "bridging potential," a single value that incorporates both overburden geology and mine geometry.

Jan 1, 2010

By Gary A. Halvorson

Plots were established on regraded abandoned mine spoil to determine if nearby good quality spoil could be used in place of topsoil for the reclamation of these sites. Gypsum, calcium chloride, and power plant ash were also tested to determine the effectiveness of these materials in reclaiming these sites. Two sites were selected on which very little vegetation was growing on highly sodic spoil material. Gypsum, calcium chloride, and ash were added to the spoil at a rate designed to reduce the (sodium adsorption ratio) SAR in the surface 15 cm to 10 or less. The good quality spoil (replacement soil) was then laid on the swface at rates of 0, 5 or 15 cm of material. The plots were seeded to a mixture of smooth bromegrass (Bromus enennis Leyss.), crested wheatgrass (Agropyron desertorum (Fisch. Ex Link) Schult.) and alfalfa (Medicago sativa L.). The addition of 5 or 15 cm of replacement spoil significantly improved vegetative growth on these sites. Chemical treatments had no effect on vegetative growth. Weathered ash showed no adverse effects on plant growth or soil properties.

Jan 1, 1991

By R. S. Dean

"Applied Mineral Physics, by R. S. Dean.- This is an introduction to the seven papers that follow. It discusses the practical aspects of mineral physics and outlines the theo¬retical viewpoint underlying the investigations reported herein.Explosive Shattering as a Possible Economical Method of Ore Presentation By John Gross and C. E. Wood. - It is shown that explosion shattering by impact is favored by large charges and by low ratio of water to charge. For 400-gram charges of dolomite crushed through 48 mesh the steam costs are less than 5 cents per ton of dolomite obtained. This is within the range of present steam costs for ball-milling dolomite.Electrical Properties of Minersl Aggergates I. Natural and Artificial Aggregates Crystallized Lead Sulphide By R.S. Dean and John Koster - This paper deals with the electrical properties of natural and synthetic galena. It is shown that massive crystalline galena has a normal positive temperature coefficient of resistance, whereas fine-grained steel galena has a negative temperature coefficient, the curve R v. T being exponential in form. That steel galena behaves somewhat like a leaky condenser is indicated by ballistic and alternating-current bridge measurements. In determining the cause of the erratic results of alternating-current resistance measurements it was observed that the measured re¬sistance was a function of the current through the specimen. The direct-current resistance was found to be proportional to the square of a superimposed radio-frequency current and independent of the frequency.The influence of grain size or the amount of metallic interface on the voltage-current characteristics at various temperatures on synthetic galena pastilles was studied. It is proved that the volts v. amperes curves are linear for all sizes and temperatures, that they have an intercept which is apparently a linear function of the temperature, and that their slopes are exponential functions of the temperature and give rise to a negative temperature coefficient of resistance.Apparatus for determing the Magnetic Constants of Mineral Powders by V,H, Gottschalk,and C. W. Davis.- A modified isthmus permeameter having a spark-suppressed primary and a multiplier in the secondary circuit to regulate the effect of capsules functioning as a twin isthmus is used to obtain quantitative data and normal induction and hystersis curves from small amounts of powdered material at fields surpassing 3.000 oersteds. Data and curves are given to demonstrate the calibration of the apparatus and the reproducibility of its results. Applications and limitations of the apparatus are noted.Magnetization Curves for Magnetite Poeders by V. H. Gottschalk and F. S. Wartman.- This paper gives measurements on four lots of purified and analyzed magnetites in mixed fractions with especial reference to the variation of permeability with grain size and with dilution by an inert material."

Feb 1, 1935

By Joe Maher

Adequate mine roof support to insure the safety of men and equipment is essential to successful mining. It is also expensive, amounting to more than one-fifth of the total mining cost at the White Pine mine. Cost effectiveness is therefore a prime consideration in developing optimum roof support. Roof bolt length is an important cost factor. This Phase II work compared uniform four-foot length Resin Bolts with the hitherto standard alternating four-foot and six-foot Resin Bolts, aiming at more cost-effective roof bolting. The data generated under this Phase II show that there is no discernible difference in the roof support given by uniform four-foot, and by alternating four- and six-foot, Resin Bolts in the relatively difficult ground selected for a severe initial test comparison; subsequent data from less difficult ground led to the same conclusion, namely no discernible difference between four-foot and four-six foot bolting.

Jan 1, 1975

By H. C. Fuller

Rhodonite, a manganese silicate, occurs as an important component of extensive veins in the San Juan district of Colorado. Recent work by the Bureau of Mines has demonstrated that typical ores of the area can be upgraded to about 30-percent manganese content. Because of their siliceous nature, such concentrates require further processing to convert the manganese into more usable forms. The investigation described in this report demonstrates the technical feasibility of producing silicomanganese from a rhodonitic concentrate by electric smelting methods. The rhodonitic concentrate used in the smelting research was prepared by dry high-intensity magnetic separation of ore from the Silver Queen vein. The concentrate contained 29 percent manganese, 2 percent iron, and 41 percent silica. The principal minerals in the concentrate were 35 percent rhodonite, 30 percent rhodochrosite, and 25 percent quartz and chalcedony. Limestone was used as the flux and coal was used as the reductant. These minerals were crushed and screened to minus 1/2-inch plus la-mesh size.

Jan 1, 1962

By Dale R. Ralston

This investigation was divided into two major phases. Phase I of the study was an examination of the occurrence and production of acid water within the Bunker Hill Mine in northern Idaho. The second phase of the project involved the study of water movement through an abandoned tailings pile. Mineralogy and hydrogeology were determined to be the two most important factors in the acid mine drainage problem. Low pH water was formed in the mine in areas of lead-zinc ore rich in pyrite. Water movement in the mine was important in the production of acid and the transportation of heavy metals. Areas of recharge to the mine were identified. A data collection network was installed to monitor water quality and quantity changes. The quantity of acid drainage from the mine was found to vary directly with surface runoff events. The study of the abandoned tailings pile was performed to determine the characteristics of water movement through the tailings material and the resultant impact on the hydrologic environment. The Page Tailings Pile, abandoned in 1969, was utilized as a study area. An extensive network of piezometers and meteorological data collection sites were installed in and near the pile. Data collected to date indicate the presence of a ground-water mound under the east half of the pile. Some transfer of ions from the tailings pile to the ground-water system has been detected.

Jan 1, 1973

By Oliver C. Ralston, Dorsey A. Lyon

Volatilization in retorts has been, until recently, the only commercial process of producing spelter, hence the zinc mine operators have had to meet the terms of the zinc smelters in regard to the following requirements: (1) Minimum percentage of zinc the ore must contain; (2) the chemical combination of the zinc in the ore; (3) the proportion present of those elements that interfere with the suceessful recovery of the zinc when the ore is retorted. In consequence of these requirements, only a comparatively small proportion of the zinc ores mined can be shipped directly to the smelters.

Jan 1, 1919

By S. P. Holt, Robert S. Sanford

"INTRODUCTION The wartime demand for iron ore and alloy steel on the west coast revived interest in iron reserves in western United States and Alaska. Magnetite was known to have been the most abundant metallic mineral at some of the old copper mines on Prince of Wales Island. In the summer of 1942, the Bureau of Mines began a program of preliminary investigation followed by core-drilling two magnetite deposits on the island.The Poor Man iron deposit on Kasaan Peninsula, Prince of Wales Island, Southeastern Alaska, was examined in August 1942 by Robert L. Thorne, associate mining engineer of the Bureau of Mines, and John C. Reed and B. N. Goddard, geologists of the Federal Geological Survey in September 1942 the area was mapped geologically and a magnetic survey was made by the Geological Survey. In October and November 1942, a more thorough preliminary examination, which included cleaning out and sampling old adits and trenches, was made by thesenior author, Robert L. Thorne, and Aner W. Erickson, engineers of the Bureau. J. G. Shepherd, a consultant of the Bureau, spent two weeks in March and April 1943 investigating the Poor Man and other deposits on Kasaan Peninsula. Core drilling was completed in June 1943.L. A. Warner, of the Geological Survey, examined all cores and interpreted structural data revealed by the drilling."

Oct 1, 1946

By K. J. Bathe

The current version of the computer program ADINA/BM (Automatic Dynamic Incremental Nonlinear Analysis for the Bureau of Mines) for linear and nonlinear, static and dynamic finite element analysis of mine structures is described. The complete report is divided into four parts. In Part A the program solution capabilities, the finite element library, the logical construction of the program and storage allocations are discussed. In Part B the theory and numerical techniques used in the program are summarized. In Part C brief problem descriptions and solution results for some sample solutions that have been transmitted as data cases with the program are presented. In the last section of the report, Part D, the users? manual of the program is presented. Program ADINA/BM is a general effective tool for coal mine structural analysis. The program is an extension of the computer program NON SAP (which was developed under an earlier contract with the U.S. Bureau of Mines). The important additional capabilities of ADINA/BM are: (1) the occurrence of all elements is time dependent, (2) all elements can be used in geometric and material nonlinear analysis, (3) the truss element can be used in elastic-plastic analysis, (4) the three-dimensional element can be employed in orthotropic, elastic-plastic and cracking and crushing analysis, (5) the program executes an out-of-core solution and thus allows the analysis of very large and complex coal mine models, (6) the truss elements can be employed as 2-4 variable-number-nodes elements, (7) a rock material model has been implemented, (8) displacement constraint equations can be imposed in the solution, (9) more flexibility in specifying the incremental solution strategy and an acceleration procedure in the equilibrium iteration are available

Jan 1, 1978

By Thomas C. Denton

In 1965 Africa maintained its position as a region of the world essential to advanced non-Communist nations for supply of vital metals and minerals. The position stemmed from the fact that Africa produced in large quantity a number of key minerals of which either or both resources and production capacity elsewhere did not approach the needs of the free world. The Republic of South Africa alone contributed more than three quarters of the gold mined in the entire non-Communist world besides an estimated 60 percent of metals of the platinum group and the entire new supply of amosite asbestos, and Africa as a whole was nearly the non-Communist world's only source of gem and industrial diamond. Africa also accounted for 83 percent of non-Communist world cobalt production. Besides these massive contributions, Africa in 1965 provided 50 percent or more of the new supply from non-Communist countries of the following mineral commodities: Lithium minerals, corundum, manganese ore: and chromite, and over 20 percent of new supply from non-Communist countries of columbium-tantalum concentrates, antimony, beryl, vanadium, phosphate rock, and copper. Africa also accounted for 18 percent of the non-Communist world's output of uranium, 14 percent of its tin, 11 percent of its lead, 9 percent of its zinc, and 8.9 percent of its crude oil output. With respect to chromite, at yearend Africa's reserves of the mineral were far larger than those of all other non-Communist regions combined. This probably also held true for manganese ore. In the case of crude oil, the fact that Africa's share of non-Communist world output was 1.6 percentage points greater than in 1964 was significant, particularly inasmuch as the output rate was continuing to increase at yearend.

Jan 1, 1967

By R. Blickensderfer

The sparking and gas-igniting tendency of steels and alloys were evaluated my measuring the radiance of spark showers produced by grinding a sample on an abrasive wheel in air, the time required for a spark shower generated on an abrasive wheel to produce an ignition in an explosive gas mixture, and the energy and speed required for impacts between various materials to ignite an explosive gas mixture. Mixtures of air-methane were found quite resistant to ignition by showers of sparks. A mixture of air-9.S pct hydrogen was used to increase the sensitivity of the tests and to thereby extend the range of materials that could be evaluated. The results of the spark-shower tests indicate that carbon steels and the alloy steels found in coal-cutter tools are among the most sparking and most incendive of any materials tested. Stainless steels, nickel alloys, and tungsten carbide are among the least sparking and least incendive. The brightness of the spark showers depended upon the degree of oxidation of the abraded particles. Impact tests against hard rocks such as solid quartz and sandstone, showed that high-carbon steel was more inc endive in the hydrogen mixture than were the softer steels or the alloy steels found in coal cutters. Ignitions were found much less likely to occur at speeds somewhat lower than the speeds currently in use in continuous mining machines.

Jan 1, 1972

By Martin Hertzberg

This Bureau of Mines study concerns the use of the tube bundle method as a sensitive and reliable detector of mine fires. The method involves the pneumatic, sequential sampling of many points in a system through branching tube bundles that lead to a single analytic station of high sensitivity, good reliability, and convenient location. Two serious limitations inhibit its use: the relatively slow response times for long lengths of narrow sampling tubes and the wall-diffusion losses for submicrometer smoke particulates. These limitations were quantitatively evaluated by measuring tube transit times and smoke particulate transmissions as a function of tube length, diameter, and pressure drop. The comparison of the data with theory offered the challenge of extending the classical, incompressible flow solutions to the two compressible cases: isothermal and adiabatic. New equations were derived for these cases, and the measured transit time data gave reasonable agreement with calculated solutions in both the laminar and turbulent regimes. The measured transmission losses of smoke particulates from several combustion sources compared favorably with those expected from Brownian diffusion losses to the interior walls of the sampling tubes. Traveltime and smoke transmission graphs are provided and, pump power requirements are estimated.

Jan 1, 1976