Search Documents

By R. F. Kehrman

Voice Frequency (VF) electromagnetic trapped miner location devices were tested for reliability and effectiveness in 93 coal mines. Tests included uplink pulsed CW, downlink pulsed OW and downlink voice evaluations. Frequencies were 630, 1050, 1950 and 3030 Hertz. Overburden depths varied from 70 feet to 1550 feet. Successful communications were established at 91 of the 93 mines. Data indicate the transmitters and receivers will operate in practically all coal mine environments. Reliability and accuracy as location devices appear to depend on noise, depth and presence of metallic objects which distort the magnetic field. In addition, theoretical models appear to define best case situations in terms of noise and conductivity. Minor hardware problems were encountered, mostly involving battery contacts, switches and antenna cables on the receivers. No hardware problems occurred with the transmitters.

Jan 1, 1978

By J. Koster

[In 1178 thn S-00n of thr !~Viluralcal Divicion, pur--'11 cf Mines, bcran an o. 't iv in': n-t!Y_Vnn of vothod; for recoverin'-1, Achol, copp~r, nK precioun notnin Zycn o;. -z of tic Bunkcrvillo KOH& in Clark County, Tcv. Tho Bunkcrvillo ran arc of t,-j)(,e of -iincrilization similar to that of 02 SWbury, Ontario, CannO, nichvl dc-?o?-:.t,. At prcoont, only n anall tonnes? p of ore has loan cxDr)scd in t*ic' :hui:er7ilIp rc: inn, ann. there is decided nce! for orjn: izod OrospectiAg ina drvclo-nnnt "crk there. It wann believod, howevar, t4it the dc,cuits varo 3ilficUntly siSnIficant to warrant an investigation iito their]

Jan 1, 1939

By T. M. Ruff

A prototype mucking machine designed to operate in narrow-vein stopes was developed by Foster- Miller, Inc., Waltham, MA, under contract with the U.S. Bureau of Mines. The machine, called a compact loader-trammer, or minimucker, was designed to replace slusher muckers in narrow-vein underground mines. The minimucker is a six-wheel-drive, skid-steered, load-haul-dump (LHD) machine that loads muck at the front with a novel slide-bucket system and ejects it out the rear so that the machine does not have to be turned around. To correct deficiencies of the tether-remote-control system, a computer-based, radio-remote-control system was retrofitted to the minimucker. Initial tests indicated a need to assist the operator in guiding the machine in narrow stopes. An automatic guidance system that used ultrasonic ranging sensors and a wall-following algorithm was installed. Additional tests in a simulated test stope showed that these changes improved the operation of the minimucker. The design and functions of the minimucker and its computer-based, remote-control system are reviewed, and an ultrasonic-sensor-based guidance system is described.

Jan 1, 1992

By Frank J. Wiebelt

As a result of the examination of many copper-zinc properties in the West Belt area of California, nine were chosen for exploration projects by the Bureau of Mines. This was part of the Bureau's wartime mineral-development program aimed at maintaining production of essential metals and increasing ore reserves. The properties explored were the El Dorado, El Dorado County; Copper Hill, Newton, and Gray House, Amador County; Constellation, North Keystone, and Collier, Calaveras County; and American Eagle and Akoz, Mariposa County. In addition to surface sampling and mapping, 41 holes, aggregating 18,134 linear feet, were diamond-drilled. Detailed results of the work done on all properties except the El Dorado and Akoz are given in this report. The El Dorado and Akoz were discussed in Reports of Investigations 3896 and 4144, respectively. Figure 1 is an index map showing the location of the mines covered in this publication.

Jan 1, 1951

By C. M. K. Boldt

Between 1989 and 1991, the greatest number of accidents in surface coal and metal/nonmetal mines involved haulage trucks. In 1995, the most frequently cited factor contributing to the 100 fatalities in these mines was powered haulage. In 1996, over 50% of the 84 Fatalities in mining that year were in surface mining. Because some of the world's largest mobile equipment is used in surface mines, and this equipment is involved in so many accidents and fatalities, new technologies are needed to alert truck drivers and people in spaces around the truck to the possibilities of collisions.

Jan 1, 1999

As part of the United States Department of the Interior, Bureau of Mines Health and Safety Research Program, Walter C. McCrone Associates, Incorporated has examined 71 samples of airborne mine dusts using the techniques of x-ray diffraction, electron microprobe analysis and light microscopy. This report details the procedures which were used in this work and documents the results which were obtained.

Jan 1, 2011

By John R. Bartels

Remote operation of continuous mining machines has enhanced the health and safety of underground miners in many respects; however, numerous fatal and non-fatal continuous miner struck-by accidents have occurred. In an effort to prevent these injuries, NIOSH researchers at Pittsburgh Research Laboratory studied the workplace relationships between continuous miner operators and various tramming tasks of the equipment using motion capture data, operator response times, and field of view data to evaluate the factors influencing operator-machine struck-by events (contact with a solid object) in a virtual mine environment. It is not feasible (nor ethical) to use human subjects to directly evaluate factors that precipitate such injuries. However, use of motion analysis data and digital human models can facilitate analysis of struck-by accident risk by allowing investigators to manipulate factors that influence injury. Factors included in this study included machine speed, direction of escape, the direction the operator was facing relative to the machine, work posture, distance from machine, and operator anthropometry. Close proximity to the machine, high machine tramming speeds, a right-facing orientation and operator positioning near the tail all resulted in high risk of being struck.

Jan 1, 2008

By Kara A. Teacoach

Current regulations for fire suppression systems in underground coal mines to protect conveyor belt installations have been in place since the Coal Mine Health and Safety Act of 1969 was enacted. Over time, the coal conveyer equipment being used and ventilation conditions underground have changed significantly, particularly the width of the conveyor belts and the use of belt air at the face. The effect of these new conditions on the effectiveness of suppression systems during a fire is not known. The National Institute of Occupational Safety and Health (NIOSH) conducted a study to evaluate the effect of air velocity, water sprinkler activation temperature, and a limited water application time on the effectiveness of water sprinkler fire suppression systems to extinguish large-scale conveyor belt fires. The fire tests were conducted using both new and used 1.8-m-wide, fire-resistant rubber belt that met the Mine Safety and Health Administration (MSHA) flame resistant requirement specified in Title 30, Code of Federal Regulations, part 18, section 18.65 (also known as the 2G test). Tests were conducted using standard response sprinklers with activation temperatures of 68 °C and 141 °C at air velocities of 0.5 and 5.1 m/s. Two tests were conducted at both air velocities for each sprinkler activation temperature, one using a new belt and one with a used belt. The results showed that the suppression system was able to suppress the fires in ten minutes to the point that a miner could extinguish it with a fire hose. However, in several of the tests, the fire reestablished itself a few minutes after the sprinkler water supply was cut off and quickly grew out of control. This report discusses the large scale experimental configuration, the installation specifications of the fire suppression system, and the results and conclusions regarding the effect of air velocity, sprinkler activation temperature, and limited water application on the suppression system performance.

Jan 1, 2010

By William P. Harris

The Lincoln Terminal System is described as a device with the capability to deliver technical information, monitor student performance, and assure learning in industrial training. An experimental unit, the LTS-3S, was constructed and delivered to the Bureau of Mines with appropriate lesson material for a test of feasibility and acceptability of this form of training in the mining environment. Operations were conducted at two mine maintenance schools. The overall results were that (1) there was a substantial improvement between tests before and after self-training on the LTS, (2) students found this an acceptable way to learn, and (3) reaction by training personnel and supervisors was favorable toward the feasibility and advantages of using the LTS in the mining environment. Transfer of the LTS to industry depends on availability of reliable units and adequate lesson material. The requirements for authors of training materials were established based on advice from mine training experts, formal analysis of lesson development procedures, and experience from efforts in lesson development at Lincoln Laboratory-It was concluded that experienced mine training instructors were best qualified to proceed effectively and economically to format instructional material for the LTS, if supported by well-designed facilities and services. Discussion with mining experts confirmed the desirability of generating training materials and delivering instruction at distributed locations to meet local training needs and in direct support of industrial operations.

Jan 1, 1975

By Charlie Vaught, Bill Wiehagen, Lynn Rethi, Pamela Kidd, Lisa Steiner, Ted Scharf, Henry Cole, Kathleen Kowalski

The most hazardous work environments share one feature in common: constant change. Many different, but constantly changing hazards are found in agriculture, construction, mining, and transport. This dynamic feature of work-place hazards varies by: (1) degree of control, (2) predictability, (3) visibility, (4) movement, and (5) degree of speed and force. In some cases the actions of the dynamic hazards are required for production to take place, and in many cases,

By J. S. Berber

Bastnasite is a natural fluocarbonate of the cerium group and affords an abundant and high-grade source of the lighter rare-earth elements. As part of a broad research program in rare-earth element technology, the Federal Bureau of Mines directed extensive experimental work to separating and purifying the rare-earth elements in bastnasite. By the use of a combination of techniques--classical chemical, ion exchange, and solvent extraction--the processing of a bastnasite concentrate to obtain the individual rare-earth elements, or groups of elements, was accomplished. A bastnasite concentrate, containing about 60 percent rare-earth oxides, was sulfated with concentrated sulfuric acid to eliminate the carbon dioxide, fluorine, and silica. Calcination at 1,200° F. made the gangue matter insoluble, thus permitting the separation of the soluble rare-earth sulfates. Essentially 100 percent of the rare-earth elements were recovered by this procedure. Since the rare-earth sulfate solution contained only trace amounts of nonrare-earth elements, subsequent separation procedures were simplified.

Jan 1, 1960

By Thomas O. Glover

Cameroon's mineral industry continued to be dominated by crude petroleum. The country's economic development depended on the production and export of crude oil. Oil output was estimated to be 56 million barrels in 1984 compared with 47 million barrels in 1983 and 39 million barrels in 1982. The country's only refinery processed approximately 16,000 barrels per day of crude oil in 1984, operating at slightly over 50% capacity. This volume, however, supplied the domestic need for motor fuel and heating oils. Cameroon's economy continued to expand despite problems and setbacks stemming from the attempted coup of April 6, 1984. Gross domestic product (GDP) growth in 1984 was 6.5%, the same rate as in 1983. Offshore crude petroleum production was the chief factor in the sustained economic growth. The country also maintained a relatively strong balance-of-payments position through oil exports. Investment, ranging up to 25% of the GDP, greatly contributed to sustained growth. The oil sector contributed approximately 14% to Cameroon's GDP in both 1983 and 1984.

Jan 1, 1986

By David A. Lipton

U.S. Bureau of Mines personnel examined mines, prospects, and mineralized areas to determine the mineral resources and potential of the Moses and Dennison Peak RARE II areas in Tulare County, California. These areas, along the west slope of the Sierra Nevada, are underlain by grarnitic rocks of the Sierra Nevada batholith and contain numerous metasedimentary roof pendants. Silver, copper, and zinc occur in contact-metasomatic deposits within the metasedimentary rocks. In the Moses area, the Powell Mine (fig. 1) contains an estimated 90,000 tons (82,000 t) of subeconomic silver, zinc, and copper resources. The King Solomon Prospect has 3,000 tons (2,700 t) of silicified phyllite containing zinc. On the Helen-Joyce Prospect, 44,000 tons (40,000 t) of gossan occur above a poorly exposed silver-zinc rich zone. Potential exists for additional mineral resources and occurrences at each of these properties.

Jan 1, 1983

By R. R. Allen

[The utilization of Western coals and lignite is a continuing study of the Bureau of Mines, and storage of these fuels is of paramount importance. Since the seasonal demand for coal in the Western States triples between the summer and winter months, successful storage of these low-rank fuels would tend to level out this variation and should reduce fuel costs. The time is rapidly approaching when the West Coast States, particularly California, will annually import several million tons of coal from the Rocky Mountain States for additional power production. This will necessitate storage of large quantities of coal, and it is thefore important to develop experience in such storage. Dry surface storage, by virtue of its flexibility and low cost, is particularly adapted to the stockpiling of large quantities of coal. This report will, therefore be primarily concerned with such storage. Inasmuch as the problems of dry, open-pit storage are quite similar to those of surface stockpiling, experiences in pit storage will be discussed briefly. Although spontaneous combustion is a hazard in storing coal, experience has proved that heats can be avoided by proper stockpiling procedures. The purpose of this report is to show that the most reactive coals can be stored satisfactorily on the surface by avoiding segregation and by thorough compaction.]

Jan 1, 1954

By Stephen P. Signer, John L. Lewis

This paper presents the results of a case study conducted in a two-entry gateroad in a coal mine where excessive roof deformation and bolt loading resulted in failure of many roof supports. The instruments consisted of 16 fully grouted, strain-gaged resin bolts, load cells on both full and partially grouted cable bolts, and vertical deflection multipoint extensometers. These instruments were installed on-cycle to measure loading on bolts in an existing support pattern and to determine if cable bolts could be used to improve roof stability. Results showed significant amounts of movement within the bolted zone. In some cases, these movements were enough to load the supports past their ultimate strength. Geology appeared to be a significant factor in localized roof degradation; that is, a very weak rock layer in the immediate roof overlain by a very strong rock layer contributed to the development of shear planes. Only one instrumented bolt had a maximum strain of less than 2,000 microstrain, which was the yield point of the steel. The average maximum strain on all bolts was 20,000 microstrain. However, electrical continuity to many gages was lost and a pattern was noted that would indicate possible bolt failure. Wire mesh and concrete cans installed as secondary support performed very effectively.

By J. Koster

[In lQ jG thc E'lcct,ro:~(: L7.l :~u..-ic:ll S;%cti ?n of t?c :I. tcIl~tr,-;lcal 3:vi cioa, ?U~CE~U of lv!irtos, bc,~m an 9.ct iv.t In-:?*t ik7;5i GI of r.:ct.l-;c?;is for rccovcrin,; niclrel, cop?ir, an2 ?? cciou:; ~ot-1 c 1;-on or; :; of tile 3unl~crvi~.l~~ tiistrict in C1ni.k Coult:r, !Icl.r. ]

Jan 1, 1939

A symposium was held on January 30 and 31, 1973, at Pittsburgh, Pa., to review the state-of-the-art in designing and utilizing diesel-powered equipment in underground mining. The Health and Safety Activity of the Bureau of Mines sponsored the symposium with major assistance from the following four participating organizations: The American Mining Congress J. Allen Overton, President The United Mine Workers of America Arnold R. Miller, President The National Independent Coal Operator's Association Cloyd D. McDowell, President The Bituminous Coal Operators' Association, Inc. Guy Farmer, President Seventeen papers were presented during four half-day sessions devoted to the general subjects of the diesel engine, the place of the diesel in underground mining, health protection using diesels underground, and maintaining safety of diesels underground. Eleven of the speakers were from industrial organizations here and abroad; one represented the Provincial Government of Nova Scotia; two were with the Department of Health, Education, and Welfare; and three reported on Bureau of Mines work related to diesels.

Jan 1, 1975

By Thomas M. Barczak, David P. Conover

Longwall shields provide essential ground control in longwall mining, yet a high percentage of shields are operating at less than peak capacity and many at well below the rated support capacity due to defective hydraulic cylinders or malfunctions in other hydraulic components. Leg pressure data are currently collected on state-of-the-art longwall shields, but typically are not analyzed to evaluate shield performance. The National Institute for Occupational Safety and Health (NIOSH) Shield Hydraulics Inspection and Evaluation of Leg Data (SHIELD) program is a Visual Basic software system that is designed to analyze leg pressure data and identify shields that are not performing to rated specifications. The program analysis is configured to detect the following conditions: (1) loss of leg pressure, (2) imbalance in leg pressure, (3) low set pressure, (4) low yield pressure, and (5) full extension of the bottom stage. Other performance assessment measures include the percentage of the support capacity utilized (ratio of peak load to yield load), the percent of time that a shield operates at yield load, the ratio of the set load to the yield load, and the amount of support capacity that is lost due to leaking cylinders. Historical record keeping will allow the user to select a particular shield and review the performance record as developed by the program for that shield. In addition to these performance assessment measures, the software will include an animated description of shield hydraulic systems that will describe the operation and significance of each hydraulic component and the impact of component failures on the shield’s capability to provide the required roof support. A general overview of the SHIELD program is provided in the paper together with an example analysis of a 2.5-year-old Australian longwall face.

By Radford B. Langston, John A. Marjerison, Graham C. Howell, Hendrik A. D. Kirsten

Probabilistic design is gaining wider acceptance in the rock engineering community since it allows more rigorous determination of risk relating to ground fall or excavation instability. Risk analysis can be conducted by various means, but the basis is formed by either objectively or subjectively determining probability of occurrence of an event. In the case of rock engineering, this event is either instability or excavation failure. Rock mass classification systems provide objective analysis of data collected on a typically subjective basis that also relate closely to excavation stability. A probabilistic analysis technique is presented that uses statistical distributions of rock mass and material properties, ground support fixture specifications, stress conditions, opening geometry, and ground support installation quality to more rigorously determine probability of failure for an underground opening and the subsequent risk to personnel.

Jan 5, 2007

By E. O. Binyon

"INTRODUCTION The Gibellini manganese—zinc-nickel deposits, are in southeastern Eureka County, Nev, T. 15 N., R. 53 E. M.D.B.M. 27.5 miles south of Eureka, the county seat.The partly explored deposits, locally known as the Black Iron or Gibellini property, were examined in May 1944 by an engineer 3/ of the Bureau of Mines, who recommended that the deposits be explored further by means of core drilling. The proposed program called for drilling six diamond—drill holes, or eight if necessary, and for trenching at two places — 200 feet northeast and 280 feet west of the shaft on the main deposit.In 1946 the project was set up, and In July, of that year diamond drilling as started. Six holes were drilled for a total length of 1,198.5 feet. No trenching or other exploratory work as done. Work on the project was stooped. October 30, 1946.OWNERSHIPAccording to county records, the property comprises a group of 13 unpatented lode claims, and ownership is divided among Louis P. Gibellini,Louis P. Gibellini and wife (both of Eureka, Nev.), and the International Smelting & Refining Co., of Salt Lake City, Utah. Five claims of the group - the Black Iron No. 1, Black Hill No. 2, Manganese No. 3, Flat No. 1, and Flat No. 2 - are owned by Gibellini. Three claims - the Black Hill No. 1, Black Iron No. 3, and Manganese No. 4 are owned jointly by Mr. and Mrs. Gibellini, and the International Smelting & Refining Co. owns the remaining five - the Black Iron No. 4 and No. 5, and Black Hill Nos. 4, 7, and. 9."

Jan 1, 1948