Search Documents

Provide the U.S. mining industry with technology for designing environmentally sound, low-cost in situ leach mining operations to produce copper from small, deep, and/or low-grade copper oxide deposits. Approach Investigate the feasibility of a new mining method--in situ leach mining-as an alternative to conventional mining for copper. Study fundamental leaching technology that will facilitate future commercial operations. Develop guidelines and procedures that will enable mine operators to design and evaluate in situ leach mining operations for any specific copper oxide deposit.

Jan 1, 1989

By George A. Morgan

Output of mineral products was estimated to be unchanged in 1983 from that of 1982 with the exception of petroleum. The country began production of crude oil from the Seme Oilfield, and all output was exported. Wd and charcoal constituted 72% of Benin's total energy consumption, and imported petroleum products and electric power accounted for the remainder. Cement was produced from imported clinker. The gross domestic product (GDP) was $1,061 million in 1982, the latest year for which information was available.2 COMMODITY REVIEW Gold.-Exploration was underway at Perma by the U.S.S.R. as part of the United Nations development program. Gold had been produced previously at Perma, where a grade of 0.289 troy ounce of gold per ton was reported, An exploitation program for the deposit was to employ about 100 people, and output was targeted to reach 1,600 troy ounces per year. Recoverable reserves were put at 96,000 troy ounces.

Jan 1, 1985

By Luis v. Coppa

Since its inception in 1910, the Bureau of Mines has been the principal Federal agency involved in ore reserve estimations, using such traditional methods as polygons of influence and variations of inverse distance weighting While adequate for estimating the average are grades in a mining block or section, these methods do mot, however, provide a consistent way of quantifying the reliability of the estimates. This report describes a technique for enhancing ore reserve estimations using geostatistics, the methodology of which combines the spatial and random aspects of geologic phenomena into a formal theoretical framework for deriving the estimation variance of ore reserves. Correctly used, geostatistics enables confidence intervals to be placed around ore reserve estimates calculated from drill hole data. A geostatistical software system was obtained -From the U.S. Geological Survey and installed, aster slight modifications, on the Bureau's Wang computer. System testing and validation was conducted using a simple cast-book-type example. This was then followed by variogram analysis, point kriging and block kriging of data from a previously worked section of a uranium mine.

Jan 1, 1984

By L. F. Willmott

The Bureau of Nines at Morgantown, W. Va., has been investigating, on a pilot plant scale, various methods of gasifying bituminous coal with oxygen and superheated steam to produce synthesis gas, as part of the broader program of finding new uses for coal. Differences in the pressure gasification methods used have depended on differences in the manner in which the pulverized coal is fed to the gasifier. One of the methods of feeding the coal that was investigated was the continuous, integrated coal-water slurry system. Goal and water were first mixed to produce a slurry; then the slurry was pumped through a heated coil. to evaporate the water fraction; the resulting steam was superheated, and some of it was separated so as to adjust the ratio of the residual steam to the coal fraction and make the resulting mixture suitable for partial combustion with oxygen in a pressure gasifier. Both before and during this reported3 developmental work it was necessary to make an extensive literature search into the technology of aqueous slurries in order to establish design criteria for the pilot plant and to correlate results of various phases of the work with that of other investigators, The pilot work coincided with the commercial development of a long-distance pipe- line for the transportation of coal as a coal-water slurry, and this fact tended to broaden the scope of the pilot plant work and the extent of the literature search. This bibliography is the compilation of the material that was collected.

Jan 1, 1963

By K. L. Erickson, Gerald A. Munson

"The need for spodumene as a source of lithia for war purposes led to the exploitation of the Edison pegmatite deposit 1-1/2 miles southeast of Keystone, S. Dak. The operation was conducted during 1943 and 1944 by the Lor Mining Co., Rapid City, S. Dak. Spodumene concentrates in the ratio of 15:1 were recovered by hand picking from a sorting belt. This method was expensive and wasteful of spodumene, owing to the small size of the crystals.Data4/ obtained by the Bureau of Mines indicates that blunging with hydroflouric acid or sodium hydroxide is a prerequisite to selective flotation. Results of tests by Denver Equipment Co., Denver, Colo., indicate that economic recoveries can be obtained in an alkaline circuit after desliming.At the request of the Lor Mining Co., K. L. Erickson, metallurgical engineer, was permitted to work in the pegmatite research laboratory to verify previous investigations and to determine problems that might be involved in commercial milling. The ensuing investigation indicated that electrolytes in the mill water produced a profound inhibiting action on the flotation of Edison spodumone.An investigation of mill water from various sources showed that some waters are suitable for the process and others are not. Subsequent testing showed that all of the available waters are suitable after treatment. The flotation of the Edison spodumene in an alkaline circuit after desliming and using oleic acid as collector is efficient and economical when the water does not contain impurities.In its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B.Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches arc under the supervision of Dr. R. S. Dean, assistant director.As the work was of a practical nature, samples from possible mill-water sources in the southern Black Hills were obtained, and commercial softening and demineralizing methods were investigated. Data on various waters tested are given in table 1."

Jun 1, 1946

By Eugene W. Bartel

This report describes in detail the circuitry used in the Automated Time Domain Reflectometry System and the testing and modification done to the system to improve the units performance and consistency. The analog ATDR software is described and explained in detail. Also attempts to implement the same Assembly Language program in a higher level language (PLM) are documented along `h two versions of the PLM program - one which uses a data filtering approach to limit noise and another which uses data averaging to reduce noise. The field testing of the analog and digital ATDR units is described along with the hardware modifications that resulted. The analog unit has been abandoned and the digital unit adopted for most field tests. Tests indicate that the digital units are much more consistent and less confusing for the lay-person to operate. The results indicate that the it can locate an abnormality in a test cable to within 5% of the true location (provided the cable phase velocity is known). The units can consistently locate shunt type faults which are less than 300 ohms and series type faults which are greater than 30 ohms.

Jan 1, 1980

By Frederick C. Trutt

This report is intended as a reference for personnel interested in the computer anlaysis of coal-mine-electrical-power systems under either normal operating conditions or fault situations. The procedures developed for this purpose are described and implementation considerations are discussed with respect to the mine-power system. Considerations for choosing a solution technique and a number of examples are included. Procedures described include the Newton-Raphson iterative technique for the analysis of normal operation as well as a non-iterative Z-bus technique for analysis of unbalanced or balanced faults. During program development, strict attention has been given to the inclusion of core and/or time saving techniques such that these algorithms may be implemented on small as well as large computers. Program languages include FORTRAN IV for batch processing applications and APL or BASIC for interactive applications.

Jan 1, 1981

By P. Cole Gregory, Michael R. Yenchek, John C. Edwards

The U.S. Bureau of Mines investigated the performance of portable power cables under transient conditions. This research had a twofold purpose: (1) to define the thermal characteristics of electrically overloaded trailing cables, and (2) to conceptualize electrical protection for cables that allows maximum cable efficiency without diminishing electrical safety in underground mines. Several tasks were under- taken in support of these goals during the 3-year research effort. Overload tests ranging from 2 to 12 times rated ampacity were conducted in the Bureau's Mine Electrical Laboratory. Two thermal models of energized type G-GC trailing cables were constructed, one based on thermodynamic theory and the other using empirical data from previous Bureau load tests. The empirical model was then incorporated into an interactive computer program that can assist designers and approvers of mining machines in selecting the appropriate size trailing cable. This program can be the basis for a cable protection system that ensures that cables are not the source of fires, ignitions, burns, or explosions underground.

Jan 1, 1993

A knowledge of the mechanics of wave propagation through the earth is essential if reliable communication systems are to be designed for coal mine environments. To obtain a reliable basis from which accurate propagation predictions could be drawn, a series of theoretical Studies have been prepared for the Bureau of Mines by Mr. Ramsay Decker of Spectra Associates, Inc. through a subcontract with Collins Radio Group. These reports formulate the analytical techniques from which wee may derive frequencies and antenna configurations that yield the optimum signal-to-noise ratios over the greatest distances in mine environments. The reports of sections 2 and 4 deal with analytical techniques for determining the signal-to-noise ratio within a mine environment for loop-to-loop and line source-to-loop antenna configurations. The analytical results of these reports were then implemented into computer programs to obtain predictions concerning through-the-earth signal propagation. These preliminary predictions are based on noise data compiled by Bensema, Maxwell and Stone, and WVU prior to the extensive research conducted by the National bureau of Standards (NBS). These initial measurements indicated a 20- to 30-dB lower noise level than that measured recently by N BS. The recent NBS data is that used by Collins in the final predictions.

Jan 1, 1974

By Dennis R. Dolinar, John L. Ellenberger, Gabriel S. Esterhuizen, Anthony T. Iannacchione

A survey of pillar conditions was carried out at 21 operating limestone mines that use the room-and-pillar method. The surveyed pillars were all located in rock that was classified as “Good” to “Very Good” using the RMR rock mass classification system. The average pillar width was 14.5m and the width to height ratio varied between 0.53 and 3.52. Pillar conditions were rated using a visual rating system that accounts for the effect of geological structures as well as stress related fracturing. Nine cases of pillar instability were recorded. Pillar instabilities were typically limited to individual pillars or small groups of pillars within an otherwise stable layout. Local geological structures such as inclined discontinuities or weak bedding planes contributed to instability in seven of nine cases that were observed. Elevated pillar stresses contributed to instability in the two remaining cases. All the unstable pillars observed had width-to-height ratios of less than 1.5. It is concluded that pillar instability is most likely to be caused by unfavorable geological structures in pillars with width to height ratios of less than 1.5. Stress related instability such as rib spalling becomes more prevalent when the average pillar stress approaches approximately 20 MPa.

By H. L. Anthony, A. C. Richardson, G. D. Coe

"INTRODUCTION The Warrior View mine of the Seaboard Coal Corporation is located in Tuscaloosa County on the Warrior River about 14 miles northeast of Tuscaloosa, Ala. The Brookwood bed at this point yields a coal with fair coking qualities, and the product from neighboring mines on this bed has been used for the manufacture of blast furnace coke. The output of the Warrior View mine, however, is used exclusively for domestic and steam-raising purposes.This paper continues the series° of reports on the washability of Alabama coals which are based upon the study of coal preparation in Alabama now being conducted by the U. S. Bureau of Mines and the University of Alabama with the cooperation of the different coal mining companies. This paper contains screen-sizing and float-and-sink tests of a representative sample of run-of-mine coal, and flakiness and crushing tests on certain sizes.Published information on the Brookwood bed is very meager. Fieldner6 gives the proximate and ultimate analyses for a number of seam samples taken from representative mines working this bed. Gandrud and Britton7 show sections of this bed taken at Searles, Ala. They also give the specific gravities of the coal, the bone, and the shale partings.Table 1 give the proximate and ultimate analyses for the 3/4 to 3/16 inch size of raw coal. Table 2 gives the sulphur content and the ash fusibility temperatures of the float-and-sink fractions for this same size. The character of the coal is very uniform throughout the range of sizes produced and, as it was not convenient to have these analyses on all sizes, this size was chosen as being representative of the coal. From the information available it is evident that the coal preparation problem is restricted to one of ash reduction.SAMPLING AT THE MINEAt the Warrior View mine the run-of-mine coal is dumped from the mine cars upon a 3-inch grizzly. The oversize is crushed in rolls set at 24 inches and joins the undersize before being elevated to the raw-coal bin ahead of the jig. The sample was caught at the point where elevates discharges into the raw-coal bin, by taking a proportional amount of the coal at 10-minute intervals over the period of a day's run, The total sample amounting to 2.7 tons was shipped to the laboratory at Tuscaloosa for the washability studies."

May 1, 1932

By D. Harrington

The greatly extended use of the underground trolley-locomotive system for hauling coal without doubt was one of the most important factors in the rapid progress of coal mining and the increased production of coal in American coal mines during the period 1910-20. Much of the superior efficiency of production of our underground coal and metal lines should also be credited to the trolley locomotive system. The trend to mechanization of mines during the past 15 years, mere particularly the past 5 years, with higher production per man employed and greatly accelerated advancement of working places, has required increased use of trolley locomotives, necessitating larger equipment, higher speeds, and more 'frequent turn over of pit cars. This is re¬flected in increased size of locomotives and the use of larger mine ears (some with a capacity up to or over 10 tons); moreover, heavier rails and larger-size trolley wires have boon or ought to have boon installed. Trolley-locomotive haulage has proved to be rapid; economical, efficient, and productive; nevertheless; in spite of these advantages, so-many hazardous features and, unsafe conditions are involved and the price paid in life and property is so high as to justify the statement that the system should be scrapped if it cannot be operated under reasonably safe conditions. Since bare trolloy wires were introduced into underground mines, they have boon responsible for the death of hundreds of diners, property damage totaling millions of dollars, an indeterminate loss of tonnage through the abandonment of mines or parts of mines, and loss of time after disasters caused by fires or explosions originated by the trolley haulage system.

Jan 1, 1945

By A. E. Raddatz

The Bureau of Mines is investigating methods for recovering tungsten from domestic resources. A calcine-quench-leach (CQL) technique was developed for the extraction of tungsten from the Golconda, Nev., hot springs ores. The deposit contains disseminated tungsten that cannot be beneficiated by conventional techniques and must be treated by hydro-metallurgical methods. The CQL procedure consists of calcining the ore at 900° C for 3 hours, quenching in a solution containing 1.5 parts of Na2C03 and 1.5 parts of NaOH per part of WO3 in the ore and at a solution-to-ore ratio of 3 to 1, leaching at 200° C and at 250 psig for 3 hours, and filtering and washing the residue. A series of closed-circuit batch tests showed that 92 pct of the tungsten was extracted from a sample containing 2.32 wt-pct W03. The pregnant solution contained 11 g/l W03.

Jan 1, 1982

By R. S. Dean

"INTRODUCTION The metallurgical research program of the Bureau of Mines has been somewhat disorganized, but generally advanced by the increased activities of the war period. The present report is for the purpose of summarizing the work of the Bureau in this field for the past 15 years and indicating its future plan.Fifteen years ago the Bureau turned from its pioneer work on the physical chemistry of steelmaking to an emphasis on raking a pure steel synthetically, rather than by refining, that is, :producing each of the steel 'constituents in the pure state and combining them by simple melting. Such a procedure permits the use of less high-grade ores, not only of iron, but of the ferroalloy metals, such as manganese and chromium,This program has led to extensive work on iron-ore concentration, agglomeration, reducibility of ores and agglomerates, direct reduction of iron ores and concentrates by a wide variety of processes; special refining processes for iron, the production of pure mangenese, chromium, and cobalt from low-grade ores by electrolytic processes, the production of ferrochromium, ferronickel, and ferronickel-cobalt from low-grade domestic ores, and the development of many special alloys to effectively use the new products.The status of the work in each of these fields and the future program of work, together with a bibliography of papers and patents by the Bureau staff on each of these subjects, are given."

Jul 1, 1946

By R. A. Franks, G. F. Friel, J. C. Edwards, L. Yuan

Two mine-fire experiments were conducted in the National Institute for Occupational Safety and Health's (NIOSH) Safety Research Coal Mine (SRCM) at the Pittsburgh Research Laboratory (PRL) which demonstrated that smoke from diesel-fuel fires of 500 kW and 660 kW heat-release rates in a return airway can develop, without causing a complete air flow reversal, into a roof layer that can migrate upwind forming a counter flow to the primary airflow in a crosscut. Subsequently, smoke can penetrate into an intake airway and create a hazardous atmosphere in the intake airway upwind from the fire. Visibility conditions less than 13 m were created by the smoke in the intake airway downwind from the crosscut. Modeling of the event with a three-dimensional, time-dependent, computational fluid dynamics (CFD) program correctly represented the smoke movement.

By Dwight L. Sawyer

To provide technology that can help decrease the dependence of the U.S. aluminum industry on imported bauxite, the main ore of aluminum, the Bureau of Mines is investigating the extraction of aluminum from abundant domestic reserves of kaolinitic clay. Miniplant studies of the continuous leaching of calcined kaolin with boiling 25-pct HC1 acid resulted in a 93- to 99-pct extraction of the acid-soluble alumina in the calcined kaolin feed. Data are presented for an acid leaching study carried out in three or four continuously stirred tank reactors (CSTR) in series, feed rates of 100 to 250 lb/hr of calcined kaolin, and total nominal residence times of 0.7 to 2.3 hr. A material balance for a 176-lb/hr calcined kaolin feed rate in a circuit consisting of three reactors, four classifiers, and five thickeners is given. Data provide detailed compositional and physical information for calcined kaolin, process liquors, and acid-leached residue solids.

Jan 1, 1983

By Thomas Gales

Longwall mining has a high potential for producing bulk production from a single face. Production is interrupted for a considerable time when it is necessary to move the equipment to a new block of coal. The frequency of such moves can be reduced by increasing the dimension of the block to be moved. Merely doubling the tonnage in a block to be mined may increase production by more than 21,000 tons per year. The time taken to move the equipment can be reduced by careful preplanning, industrial engineering analysis, and specially designed equipment. Reducing its move time from 30 days to five days can increase production by more than 25,000 tons per year. Increasing the panel dimensions and reducing the move time can give an increase in pretax profits of more than $600,000. A comprehensive bibliography is included.

Jan 1, 1977

By Gerald L. Finlinger

This Bureau of Mines publication reviews underground methane drainage programs being conducted in various coalbeds. Equipment used in drainage programs such as drills, underground pipelines, and methane monitoring systems is described.

Jan 1, 1980

By H. S. Auvil

[The shrinkage of coke after formation is one of the variables that effects the net expansion of the change in both industrial and test ovens. Various test results5/ have been interpreted as indicating that cokes from certain coals shrink to a marked extent and that other cokes show very little shrinkage; but no comprehensive experimental study of the shrinkage of coke after its formation and of the factors influencing this shrinkage has come to the attention of the authors.]

Jan 1, 1940

By Fraser M. Walsh

The objective of this program was to determine by laboratory experiments the kinetics and mechanics of the reactions that produce acid in coal mine drainage. The program was divided into three phases: In Phase I, five coil mines, representative of Appalachian coal mines, were chosen for sampling and an experimental design was identified suited to accomplish the program objectives. In Phase II, the five mines were sampled and test protocols applied. The results showed most pyrite weathering to be based on oxidation in the presence of water. Iron bacteria, especially Thiobacillus ferrooxidans, catalyzed the rate of pyrite weathering by a factor of three. An increase in initial iron concentration in a system that modeled the nine environment acted to inhibit bacterial catalysis of weathering. In Phase III, five tailings piles were sampled and the material obtained was used to evaluate this method of bacterial catalysis inhibition. The evaluation verified method effectiveness; inhibition of over 80% of the release of weathering products was observed.

Jan 1, 1982