Search Documents

By Herbert R. Babitzke

As part of a project to develop refractory metal alloys suitable for high-temperature structural applications, the Bureau of Mines applied solid solution and precipitation-hardening techniques to columbium and tantalum alloys. Thirty-three alloys were evaluated to determine their formability, strength, and oxidation resistance. Three alloys had tensile strengths near 40,000 psi at 1,200° C: Cb-1N-5W-5V-10Hf (No.4), Cb-15Hf-5W-0.5B (No. 31), and Cb-15Hf-SW-IB (No. 32). Oxidation resistance of the high-strength alloys was good. Alloy4 gained only 34 mg/cm2 at 1,200° C, and 21 mg/cm2 at 1,000° C in 2 hours. Hot forming was done without any protection from oxidation.

Jan 1, 1968

By F. P. Haver

Because of increasing concern with air pollution, the Bureau of Mines has developed a hydrometallurgical procedure to obtain elemental sulfur from chalcopyrite (CuFeS2) by means of the following reaction: CuFeS2 + 3FeCl3 ? CuCl + 4FeCl2 + 2S. Under optimum conditions, 99.6 percent of the copper and 71.6 percent of the iron were extracted in 2 hours from a typical mill concentrate containing 75 percent CuFeS2 and 15 percent pyrite (FeS2). At the same time, 68.2 percent of the sulfur in the concentrate was oxidized to the elemental form. The leach was highly selective; gangue minerals, including pyrite, were not attacked, thus accounting for the relatively low recoveries of iron and sulfur. To obtain these results, the concentrate was ground to 98.9 percent minus 325 mesh, and 300 grams was treated with 1 liter of boiling ferric chloride (FeCl3) solution. The FeC13/CuFeS2 ratio was 2.7. Cement copper containing 99.9 percent copper was recovered from the leach solution by cementation on sponge iron. Excess iron, dissolved during leaching and cementation, was removed from the stripped solution by crystallization. Ferrous chloride (FeCl2?4H2O), obtained as a byproduct, was converted to high-purity ferric oxide (Fe203) and HCI by an oxidizing roast. The hydrochloric acid was then electrolyzed to obtain chlorine, which was used to regenerate the leach solution. The leach residue, which contained ~50 weight-percent elemental sulfur, was treated with an organic solvent to recover the sulfur and cyanided to reclaim gold and silver.

Jan 1, 1971

By Raymond Derzay

This publication is intended to be of value to the mineral industry in establishing and maintaining effective programs for preventing noise-induced hearing loss. Factors involved in this loss and the need for and the requirements of an effective hearing conservation program are discussed. The legal and legislative history of compensation for hearing loss is briefly reviewed. A review of statutes is not attempted since several States have recently modified) or are in the process of modifying their laws regarding permissible noise exposures) required hearing protection) and/or compensation for hearing loss. A review of other aspects of the problem of industrial noise in terms of medical, physiological) and psychological frames of reference is included. A hearing conservation program is described in detail. Appendixes detailing the names and addresses of a few equipment suppliers are included. References are provided for those who may wish to delve more deeply into the medical, technical, and scientific considerations of noise and its effect on man.

Jan 1, 1972

By Radford Schantz

In 1990, the Bureau of Mines (BOM) conducted a mineral investigation of the mines and prospects in the East Mojave National Scenic Area (EMNSA). San Bernardino County. California During field work. BOM identified 701 mines and prospects in EMNSA for which the geology, mineral resources, and mining history were compiled and summarized. Analytical results for 1.188 rock samples collected are tabulated. Total value of identified resources in EMNSA is $5.0 billion. Twenty-four mines and prospects were deemed profitable under current economic conditions. Development could generate considerable economic benefits to San Bernardino County. Potential economic benefits from mining the deposits were evaluated under the following access restrictions for EMNSA: 1) fun access, 2) HR 3460, and 3) S 11/HR 780. Under the full access scenario, cumulative mine revenues are $3.0 billion, cumulative personal earnings at mines and supporting industries are $0.94 billion, and annual jobs at mines and supporting industries are 2,379. Under HR 3460, mine revenues, personal earnings, and annual jobs are $2.9 billion. $0.88 billion, and 2,165, respectively. Under S 11/HR 780, mine revenues, personal earnings, and annual jobs are $1.0 billion, $0.32 billion, and 936, respectively.

Jan 1, 1990

By Farrel W. Lytle

Instrumental analysis has become an indispensable tool in research and production of the rare-earth elements. This development can be attributed mainly to a combination of two factors--the marked chemical similarity of the rare-earth elements, which excludes classical methods of analysis, and the speed and accuracy of instrumental-analysis techniques. With continued improvements in methods of producing high-purity rare-earth elements, keeping pace instrumentally is becoming much more difficult. Accordingly, greater emphasis is being placed on improving instrumental limits of detection and accuracy. The methods employed most frequently for determining impurities in rare-earth elements involve use of the optical-emission spectrograph (3, 4)4/ and the spectrophotometer (9). Although numerous X-ray-emission spectrographic methods (6-8) have been developed for analyzing rare earths, these techniques have not included detection of low-level impurities. This investigation was conducted to find the precision and accuracy of X-ray fluorescence in deter-mining impurities in rare-earth oxides in the 0.01-to 1.0-percent-concentration range.

Jan 1, 1959

By Laurance L. Oden

The Bureau of Mines conducted corrosion tests of 18 commercial alloys in H3 P04 -phosphate rock or A1,03 slurry, in 10 pct HF, and in 25 pct H2 SiF6 to simulate three environments anticipated in a Bureau process to extract fluoride values from phosphate rock. Small alloy coupons were rotated in duplicate tests at 4.4 to 21 fps in the slurry at 170° C to determine rates of erosion-corrosion. At 4.4 fps the lowest rates, in mils penetration per year (mpy), were measured for Hastelloy C-276 (<20), Hastelloy B (30), and Inconel 625 (150);the rates increased at 21 fps to 55 mpy, 45 mpy, and 1,000 mpy, respectively. The corrosion rate for all alloys exceeded 40 mpy in either the equilibrium vapor or liquid phases of aqueous solutions containing 10 pct HF or 25 pct H2SiF6 at 100° C. Uniform corrosion in 10 pct HF at 50° C was observed only for Inconel 625 (22 mpy), Hastelloy C-276 (43 mpy), and Illium 98 (17 mpy). Inconel 625 (0.75 mpy), Hastelloy C-276 (1.3 mpy), Illium 98 (1.7 mpy), and Incoloy 825 (0.45 mpy) were attacked uniformly in 25 pct H2SiF6 at 50° C.

Jan 1, 1974

By T. H. Jeffers

Significant amounts of cobalt, a strategic and critical metal, are present in readily accessible spent copper leach solutions. For example, recovery of cobalt at two major u.S. copper operations could produce about 1,300,000 lb Co annually, about 13 pct of domestic consumption. However, techniques such as solvent extraction and precipitation have not proven cost effective in separating and recovering the cobalt from these low-grade domestic sources. The Bureau of Mines has devised a procedure using a chelating ion-exchange resin to extract cobalt from a pH 3.0 copper leach solution containing 30 mg/L Co. Cyclic tests in 4-ft-high by 1-in-diam columns gave an average cobalt extraction of 95 pct when 65 bed volumes of solu-tion were processed at a flow rate of 4 gpm/ft2 of resin area. After an impurity scrub, eluates contained, in grams per liter, 0.4 Co, 0.2 Ni, <0.001 Cu, 1.3 Fe, 2.8 Zn, and 0.008 AI. Solvent extraction procedures to remove impurities, reject nickel, and concentrate cobalt produced a cobalt sulfate solution containing 80 g/L Co, 0.05 g/L Ni, and not more than 1 mg/L Cu, Fe, Zn, or AI. Based on data from commercial electro-winning operations, this solution appears suitable for production of metallic cobalt.

Jan 1, 1985

By A. R. Rule

Laboratory tests were conducted to study removal of magnesium impurities from western phosphate rock concentrates by selective leaching. The systems evaluated included leaching with dilute sulfuric acid, with ammonium sulfate, and in an aqueous medium with sulfur dioxide gas. Set standards for the magnesium impurity level of phosphate rock concentrates are not available, but industrial practice has indicated that magnesium in excess of 0.3 percent MgO causes problems in phosphoric acid manufacture. Removal of magnesium was accomplished with all three systems. With dilute H2S04 the magnesium level was reduced to less than 0.1 percent MgO with an accompanying P205 loss of 6 percent. Magnesium oxide levels from 0.3 to 0.2 percent were obtainable with ammonium sulfate. However, the system requires concentrate roasting at temperatures of 900° C or higher, heated pulps (100° C), and large quantities of ammonium sulfate. Selective leaching was obtained using S02 gas in an aqueous concentrate slurry. Magnesium oxide content was reduced to less than 0.1 percent without loss of phosphate.

Jan 1, 1970

By John A. Breslin

Size distributions and concentrations of particulates emitted from diesel engine exhausts were measured with cascade impactors. Samples were taken from the exhaust of two types of engines using three types of fuel and operating under five different engine speed and load conditions. The measured mass median diameters of the diesel particulates were typically about 0.3 um. There was no significant difference in mass median diameter between engines or fuels and only a slight dependence on operating mode. Concentration measurements ranged from 14.2 to 250.9 mg/cu m, and calculated mass outputs, from 64 to 10,000 mg/min. Significant differences in mass output were found between engines, fuels, and especially between different operating modes. The quantity of clean dilution air that would be required to reduce the particulate mass concentration below the 2.0 mg/cu m respirable dust standard for coal mines was greater than the dilution air required to meet the standards for noxious gases for both engines tested.

Jan 1, 1976

By G. W. Elger

The Bureau of Mines conducted laboratory and larger scale studies on samples of domestic perovskite and ilmenite ore concentrates to devise a procedure for recovering TiC from these ores. From the concentrates, mixtures of titanium and calcium carbides were produced. The carbides were then ground and reacted with water. This reaction decomposed the CaC2 to acetylene and hydrated lime and simultaneously liberated the TiC. Using a combination of elutriation and gravity-separation techniques to separate the hydrated lime, approximately 93 pct of the titanium was subsequently recovered as purified carbide containing 54 to 70 pct titanium with CaO content as low as 0,6 pct. This combination of techniques can be used to separate more than 90 pct of the CaO from the TiC. Therefore, this carbiding procedure is a viable method for treating titaniferous materials, including perovskite, that contain more than 20 pct CaO. Tests made in a static-bed reactor showed that for the reaction of TiC with elemental chlorine to produce titanium tetrachloride (TiCI4), a temperature of at least 940° F is desirable to achieve a suitable extraction of titanium in a laboratory chlorination reactor. In fluidized-bed tests at 840° F, 98 pct of the titanium contained in TiC was extracted.

Jan 1, 1980

By L. Keith Hudson

The purpose of this study is to provide data that demonstrates that the Alcoa flash calciner design can be used for the decomposition of AlCl3?6H2O to A1203. Heat and material valance data for calcination provides data on the partial pressure of HCl in the off-gases. Experimentally determined data for the HCl partial pressure, over solutions expected in producing alumina from clay by the hydrochloric acid process, show that HCl can be absorbed from the off-gases into process solutions to effect crystallization of AlCl3?6H2O.

Jan 1, 1979

By G. E. Rennick

A siphon-type laboratory airlift well was designed and operated by the Bureau of Mines to study the concurrent flow of air and oil in small-diameter pipes. Glass flowstrings ranging from to 1 inch in diameter and from L4 to 64 feet in length were equipped with various-sized air-entry jets. Liquid holdup volumes were used to correlate vertical-flow data, and empirical equations for computing gas requirements were derived. The effect of flowstring length on flow efficiency, oil- and gas-production rates, and gas-oil ratios was relatively minor at all flowing pressures. Air-jet sizes and flowstring diameters, however, had a marked effect on flow efficiency and oil- and gas-production rates. The small air-jet sizes increased maximum flow efficiency and its associated flowing pressures but decreased oil- and gas-production rates. An increase in flowstring diameter increased maximum flow efficiency with its associated flowing pressure and also increased the production rates of oil and gas.

Jan 1, 1965

By Robert M. Cox

The objective of this study was to determine if significant relationships exist between coal mine roof stability and the time roof is left unsupported. Additional factors such as geology, opening geometry, and mining methods were also studied: to determine their relative influence on mine roof stability. The results of the study indicate that geologic factors such as shear zones (either joints or faults) and changes in roof rock lithology were the principal factors governing mine roof stability. The time lapse factor appeared to be of critical importance when poor mine roof conditions are encountered. The study pointed up the need for improved and permissible rock mechanics instrumentation for use in coal mine investigations.

Jan 1, 1974

By B. W. Gandrud, G. T. Bator

The recent introduction of small coal jigs in Alabama to meet the needs of truck - mine operators for cheap and economical cleaning equipment marks another step in Alabama's pioneering record in the mechanical cleaning and preparation of coal . During the past 4 or 5 years a number of these small jigs , with capacity of 5 to 10 tons per hour , have been installed at Alabama truck mines and at a few truck mines in Illinois , Tennessee , and Pennsylvania . Most of the installations have been at mines that specialize in the production of domestic , stoker coal . This report describes three models of small jigs and includes performance data obtained recently on one of the models by the Bureau of Mines, United States Department of the Interior , in cooperation with the University of Alabama, Tuscaloosa , Ala . , for the purpose of comparing it with fullsize jigs on a performance basis . With literally hundreds of truck mines now in operation throughout the country , it has been assumed in preparing this report that there is widespread interest in the availability of small - scale inexpensive preparation equipment for use at such mines in the production of steam and domestic coal and in some instances coal for manufacture of coke . Practically none of the coal from Alabama truck mines is scld to coke - oven plants ; but in some sections of the country truck mines supply a considerable amount of coking coal, and the use of small, inexpensive washers at some of them might be very advantageous during the present war emergency from the standpoint of increasing pig - iron production through improvements in coke quality .

Aug 1, 1943

By W. L. O'Brien, E. A. Rowe

Electrorefined vanadium with additions of up to 5 percent by weight of yttrium, cerium , lanthanum , praseodymium, neodymium, and samarium was melted to ingots in a nonconsumable electrode arc in a helium atmosphere . The ingots were rolled into strips and evaluated for the effect of the alloying elements on hardness , tensile strength , ductility , recrystallization temperature , and microstructure . Except for samarium , average additions of alloying elements of 1 to 2 weight - percent resulted in the retention of 0.12 to 1.05 weight - percent in the alloys and reduced the ultimate tensile strength from about 48,000 to approximately 30,600 psi . The corresponding yield stress (0.2 percent offset ) was reduced from about 40,700 to approximately 20 , 200 psi . Diamond pyramid hardness (DPH) was reduced from 117 to an average of 62 kg /mm² . Increased malleability at room temperature resulted with yttrium and all rare - earth- metal additions , except samarium , particularly with more than 0.25 weight - percent additions . Decreasing oxygen contents corresponded with the changes noted in the mechanical properties of the alloys . The recrystallization temperature of electrorefined vanadium was reduced from approximately 950 ° to 800 ° C. Yttrium or a rare- earth metal content , except samarium , in excess of 0.1 weight - percent in vanadium produced a second phase suggestive of an eutectic which indicated a possible maximum solubility of less than 0.1 weight - percent for both room and elevated temperatures .

Jan 1, 1964

By Charles K. Rose

The Cebolla Creek titaniferous iron deposits near Powderhorn in southern Gunnison County, Colo., were examined by the Federal Bureau of Mines as part of an overall program to investigate the Nation&apos;s titanium and iron resources. The deposits occur around the periphery of the Iron Hill stock, which underlies an area of about 12 square miles. Concentrations of magnetite, ilmenite, and perovskite arc localized along fractures in the pyroxenite stock. Mineralogical studies of composite surface samples collected in 1956 showed that most of the iron is present in ilmenite-bearing magnetite. Perovskite is the chief titanium mineral in the magnetite-rich and augite-rich types, and sphene is the principal titanium mineral in the placer material. The mica-rich rock contains approximately equal amounts of perovskite, ilmenite, and sphene.

Jan 1, 1960

By E. G. Davis

A research program to evaluate the use of ceramic die inserts for ferrous diecasting was initiated by the Bureau of Mines at its Tuscaloosa Research Center. Data were compiled from the literature to characterize selected ceramic materials with respect to thermal properties, thermal-shock resistance factors, chemical reactions with molten metals, and processes required to form die components. With this information and a computer model developed for predicting temperature and stress patterns induced in ceramic materials during simulated ferrous diecasting operations, 27 candidate materials were evaluated. After evaluation, only 15 were considered for testing in an apparatus constructed to immerse the ceramic specimens in molten cast iron. Of these, 13 were tested in a modified testing unit in which cast iron was poured onto the specimens. These tests resulted in the selection of three materials for further testing: boron carbonitride (50 pct B4C:5O pct BN), boron nitride-grade M (BN-M, 40 pct BN, 60 pct Si02), and pyrolytic boron nitride (PBN). Tests in a gravity-flow die unit showed that PBN was thermal-shock resistant and could be used in diecasting of ferrous metals.

Jan 1, 1981

By Frank E. Cash

Accident prevention is an integral part of the operating procedure of the petroleum industry, and refinery officials and employees throughout the United States are exerting concerted effort to reduce the frequency and severity of accidents and are realizing definite results. In other words, the petroleum industry is safety conscious to a much creator decree than most of the other mineral industries. On January l, 1936, there were 11 operating, refineries in Louisiana with a crude-oil capacity of 199,750 barrels per day.4/ This report deals with safety in four of these refineries representing. 72 percent of the refinery capacity of Louisiana.

Jan 1, 1940

By B. W. Jong

As part of the Bureau of Mines program to develop substitutes for critical and strategic materials for metallurgical applications, the Tuscaloosa Research Center has evaluated the effect of additives and starting materials on the sintering and strength properties of sialon (silicon-aluminum-oxynitride) compositions fabricated by conventional pressing and sintering techniques. Sintering and MOR (modulus of rupture) data were developed for sialon compositions produced from three components, Si3N4, A1203, and AIN. When doped with Y203 to aid in sintering, the highest MOR values were obtained with compositions containing between 20 and 30 mole-pet (A1203 + AIN). The effect of the crystalline phase of the Si3N4 and Al203 used in the three-component system on MOR also was investigated. Alpha-Si3N4 and ?-A1203 were found to be the best starting materials. A sialon composed of 67.4 mole-pct a-Si3N4 plus 32.6 mole-pct (?-AI203 + AIN), doped with 5 wt pct Y203, had MOR values at 25°, 1,200°, and 1,400° C of 40,300, 40,300, and 31,100 psi, respectively. Samples of this composition doped with Gd203, MgO, Zr02, and ZrSi04 also were evaluated. The ZrSi04-doped sialon had higher MOR values than Gd203-, MgO-, and Zr02-doped materials but lower MOR values than the Y203-doped sialon. The MOR values of ZrSi04-doped sialons were 25,000 and 25,900 psi, respectively, at 25° and 1,400° C.

Jan 1, 1981

By G. W. Birge

Carbonizing properties of the principal coal beds of Butler County, Pa., are described in this report by the Bureau of Mines. Eight samples, representing the Upper Freeport, Lower Freeport, Upper Kittanning, Middle Kittanning, Lower Kittanning, Clarion, and Brookville beds, were carbonized at 900° C. by the Bureau of Mines-American Gas Association (BM-AGA) method. Butler County coals rank as high-volatile A bituminous and are generally characterized by high sulfur content compared with Appalachian coals used for industrial coking. If cleaned, the Brookville and one sample of Upper Freeport coal would be acceptable as the major component of metallurgical coking blends. The other Butler County coals tested would be unsuitable for this purpose because of either excessive sulfur or poor coking properties.

Jan 1, 1962