Search Documents

By J. van der Walt, A. Whillier

Reference is made to the approach to mine cooling in which the service water is used as one of the means of distributing refrigeration, and attention is drawn to various engineering disciplines or functions necessary for effective distribution and reticulation of cold water from refrigeration plant. The demand for service water is intermittent, the peak flow-rates being typically two to three times the average flowrate. The refrigeration plant, on the other hand, must preferably be operated steadily throughout the day and night, with the result that a large storage dam for cold water must be incorporated into each system in order to even out the surge in demand for water. These dams should be operated as constant-temperature, variable-volume reservoirs. The conventional cascade system involving dams on each level is not the best for sending water down mines, and schemes are described that avoid the need for such dams. Reference is made to various tests that were carried out, and to several large systems that were installed. Management and organizational problems that could arise as a result of new technological developments in mine cooling are referred to, and cost figures are quoted to indicate the large potential savings, In addition to the improved environmental conditions, that can be achieved through the use of integrated water systems.

Jan 1, 1979

By G. A. Matthrsuis, R. N. Morris

The paper identifies two zones in a Leeds flotation cell. The ratio (13)of the dissipative forces and the interfacial tension force acting on a bubble and a solid particle are shown mathematically to be proportional to the square of the particle diameter for the quiescent zone and inversely proportional to the particle diameter for the turbulent zone. To locate the range of operation, correlations were established for the bubble diameter through photography and bubble counts. 13was found to be fairly constant in the particle size range 38 to 150 ",m, and the level of turbulence unlikely to affect the bubble-particle attachment and hence the beneficiation efficiency. This was verified in a series of flotation runs with a standard Leeds cell and a modified cell of twice the height to increase the capacity of the quiescent zone. A series of tests on the size range 300 to 600 ",m showed that the turbulence level had a marked effect on the cell performance through a relative improvement in the beneficiation efficiency due to the increased height of the cell. To identify the significant variables in the size range 38 to 150 ",m, a factorial design was carried out. Promoter dosage and particle size were found to be significant, aeration rate and impeler speed being insignificant at the 95 per cent confidence level. Multiple regression correlations were established for the recovery of organic material, mineral rejection, and beneficiation efficiency.

Jan 1, 1988

Advances in extractive metallurgy, 1977. Proceedings of the third symposium organised by the Institution of Mining and Metallurgy held from 18-20th April 1977. London, the Institution of Mining and Metallurgy, 1977. 244 pp. £18,50. Coal preparation A meeting of the Organising Committee of the Eighth International Coal Preparation Congress took place in Moscow on 24th and 25th May, 1977. Representatives NIM reports Report no. 1906 An automated instrument for measuring the effects of impurities on cathodic-current efficiency during the electrowinning of zinc. (2nd Sep., 1977). Report no. 1908 An analysis of the replies to a questionnaire on materials of construction for ore hoppers. (16th Sep., 1977). Report no. 1913 The mechanism and rate of reduction of Mamatwan manganese-ore fines by carbon. (2nd Sep., 1977). Report no. 1914 The thermodynamics of the formation of sulphate complexes of iron (111), cobalt (11), iron (11), manganese (11), and copper (11) in perchlorate medium. (15th Sep., 1977). Report no. 1924 The composition of chromite grains from varwUB Witwatersrand reefs. (23rd Sep., 1977). Atomic absorption The Perkin-Elmer Corporation of South Africa is planning to hold an Atomic Absorption Autumn School in Cape Town from 10th to 13th April, 1978. Travel bursaries Two Atlas Cop co travel bursaries for study tours of Swedish mines may be awarded annually to young mining graduates. Stability in coal mining The First International Symposium on the above subject is to be held in Vancouver (Canada) on 5th to 7th April, 1978.

Jan 1, 1978

By R. Hoare

TSG Consulting works with many of the major global mining companies using simulation modelling as an integral component in their development team's processes to determine which combination of infrastructure options, operating performance and operating rules best achieve project goals. All systems can be divided into a series of subprocesses. Conventional management and design practices focus on the optimisation of these system components. However, the interaction between subprocesses means that improvements made to the individual components do not necessarily translate into total system performance improvement. TSG Consulting advocates a `total integrated system approach' to understanding the behaviour and performance of complex interacting systems. In a constraint-based integrated set of processes, the instantaneous system capacity is limited by the subsystem component capacity that is the bottleneck at that point in time. Additionally, real world stochastic and dynamic influences tend to have knock-on effects across subsystem boundaries. This necessitates the requirement for simulation modelling to develop and validate solutions that are sufficiently robust to deliver sustainable outcomes. The key to maximising production is to understand the causes and effects the inherent variability has on component performance, subprocess performance and most importantly, the total integrated system performance. The correct use of simulation modelling techniques allows study teams to evaluate the relative merits of different capacity enhancement proposals. Put simply, when done well, simulation modelling provides a quantitative and rational process to enhance the knowledge and insight needed to make informed decisions.

Jan 1, 2007

By A. Koursaris, J. B. See

An investigation is described in which the resistivities of Mamatwan manganese ore, Delmas coal, and Iscor coke, at temperatures or up to 1400°C were determined, as well as the resistivities of mixtures of ore of a constant size range with Delmas coal or Iscor coke of three different size ranges. The resistivities of the ore and the coal were characteristic of those for semi-conducting materials, were strongly influenced by temperature, and decreased by several orders of magnitude between room temperature and IOOO°C. The resistivity of the coke changed only slightly between room temperature and 1400°C, and the resistivity of the coal approached that of the coke at I300°C. This provides support for the theory that the resistivity of carbonaceous reducing agents is primarily a function of heat treatment, and not of the rank and composition of the coal. Above 1200°C, the resistivity of mixtures of ore and coke fell steeply owing to an increase in the volume fraction of coke in the mixture and to the formation of slag. The results were similar for the three different size ranges of coke. The extremely high resistivities of ore-coke and ore-coal mixtures at Iow temperatures indicate that there is unlikely to be much conduction of current in the higher regions of a furnace. Thus, the resistance of a furnace is governed mainly by the conditions at the electrode tips and in the molten regions. To explain the very Iow resistances of furnaces, usually, about I m£?, it would be necessary for investigations to be conducted under conditions similar to those in the active zone of a furnace.

Jan 1, 1980

By G. W. Holl, E. G. Fairon

A review of some aspects of shaft design by G. W. HOLL, Pr. Eng., Associate of the Mine Managers Association of South Africa (Fellow)- and E. G. FAIRON, Pr. Eng., F.S.A.I.E.E., M.I. Cert. M.E.E., M.I.Mech. E., (Visitor) The reasons for the choice of vertical shafts in preference to inclined shafts of comparable capacity are set out, and the conclusion that the former are superior in virtually all circumstances is substantiated. The shapes of vertical shafts sunk during the past sixty years are recorded, and the shapes of those sunk during the past decade are analysed. From this analysis it is clear that circular and elliptical (and quasi-elliptical) shafts are the shafts of the future and that the rectangular shape will conceivably become obsolete. The determination of the size of shaft is discussed and it is forecast that shafts of a diameter of 13 metres and over will probably be sunk without difficulty in the years to come. The depth of the shaft is determined intrinsically by the Mines and Works Regulations applicable to factors pf safety of winding ropes and the design of the winding system. The Blair winder is the most suitable winder for hoisting rock, men, and material from a depth of, say, 3000 metres on an economic basis. Tertiary shafts will, therefore, be unnecessary in future deep-level mining projects at the limit of depth now envisaged. A few other factors relating to shaft design are described.

By S. P. Molefe

Mr Chairman, members of the executive committee, the sub-committee, distinguished speakers at this opening plenary session, delegates, affiliates, ladies and gentlemen. It is with pleasure that I have been called upon today to make these opening remarks and officially welcome you al at this auspicious assembly, the Fifteenth Congress of the Council of Mining and Metallurgical Institutions. Not only am I pleased to open the proceedings at this plenary session but for me to do so at Sun City in the North-West Province makes me doubly pleased. It is my wish that al delegates and their companions will enjoy the activities that are planned throughout the Congress and leave here with minds refreshed and stimulated by the technical sessions and memories enriched by being in such a unique and truly delightful setting as exists here at Sun City. The mix of delegates present reflects CMMI activities in many countries throughout the world-Australia, Japan, China, United Kingdom and South Africa among others. When it comes to mining and related activities, South Africa has a place at the top, a dominant role in platinum, gold, chromium, vanadium, dimension stone, coal and so forth, and here in the North-West Province we can proudly declare that some 25 per cent of the revenue from minerals in South Africa, namely R47 billion come from this area. Furthermore, we lead in the production of platinum group metals with 94 per cent of South Africa's total sales and thus hold first place in the world, 46 per cent of dimension stone sales, 32 per cent of chromate and 25 per cent of gold sales.

Jan 1, 1994

By D. P. Enright, D. D. Howat

Austenitic manganese-steel castings are very widely used in crushing and grinding in the' gold-mining industry in South Africa, The service life of a casting in a short-head crusher is difficult to predict because there are no clear-cut criteria by which such a judgement can be made, The addition of molybdenum and zirconium to the castings for crushers failed to result in improved performance, The results of extensive tests with through-hardened steel castings were very disappointing, mainly because of a design factor in the bowl liner. The design of the bowl liner is an important determinant of the life and performance of these castings. The extent to which the material in a crusher is reduced in size has profound effects on the consumption of metal and power, and on the effective life of a casting. Tests on manganese-steel castings in an 8 ft by 12 ft rod mill provided data on the total consumption of metal, and on the variations in the pattern and rates of wear of liners over lengthy periods. Progressive changes in the wear profiles of the lifter bars and the other liner components showed unexpected features. There are clear indications that, whereas a set of lifter bars will at first lift the charge strongly with relatively little slippage, there is a later period characterized by more slippage and greater wear on all the liner components.

Jan 1, 1980

The general standard of engineering in South Africa will, it is believed, reach new heights after the establishment of the S.A. Council for Professional Engineers (SACPE) in February, 1969. The Council is being created to establish standards for professional engineers in this country and ensure that the quality of engineering is maintained at a high level. In terms of the Act of Parliament under which the new Council will operate, all consulting engineers will have to be registered if they wish to remain in private practice. While engineers who are not in private practice cannot be compelled to register, it will be in their interests to do so, according to a statement issued by Mr M. R. Gericke, chairman of a Shadow Council which is at present preparing for registration and drafting the requirements for registration. Registration is seen as an important move towards maintaining the quality of engineering in South Africa. Engineers will be encouraged to strive for professional status by gaining the necessary qualifications and the varied range of experience required by the Council before registration. All work done by registered professional engineers will have to conform to certain minimum standards. A spokesman for the Council has urged all engineers to ensure that they apply for registration when the Act comes into force in February. The Council is also anxious to gain the co-operation of employers in ensuring that the holders of professional engineering posts will be registered. Full information regarding registration will be sent to engineers throughout South Africa early this year, and announcements will appear in the press.

By L. C. Stilwell

The paper will attempt to identify the threats, however obscure, that could confront the South African platinum industry. South Africa has the largest reserves of platinum group metals in the world, and is the largest producer of those metals. This situation is no different from that which existed in the gold sector fifty years ago. Since then South Africa?s share of world gold production has dwindled, and the gold mining industry has lost its dominance. Unlike gold, platinum has widespread use as an industrial commodity. Its investment value is a minor portion of its total value. It is therefore subject to different market forces. The sheer magnitude of the industry in South Africa obscures the fact that it is a wasting industry, and that South Africa exports almost all its production as a refined metal in the form of autocatalyst. Since Hotelling published his seminal work The economics of non-renewable resource in 1931,the science of mineral economics has developed exponentially. The paper will present a background of mineral economic theory and compare to this the development of the South African platinum industry. Of particular concern to a mineral exporting country is the question of mineral rent?its definition and employment. This will be the mail theme of the paper.

Jan 1, 2006

By L. W. Helle

This paper summarizes the investigations carried out into a defect involving the corners of billets rolled from continuously cast blooms, which broke open during the rolling process. As it was believed that the defect must be connected with the formation of subcutaneous blowholes in the bloom, the investigations were directed towards an understanding of the roles of the three gases involved in the process. In an extensive trial programme, samples were taken from the heat at all stages of processing, as well as from all the raw materials and alloys. The main sources of nitrogen were found to be re blows, pick-up from the alloys added to the ladle (especially graphite), and open-stream casting. The major source of hydrogen was moisture in the alloys, especially high-carbon ferromanganese and silicomanganese. Further, it was established that the moisture content of the alloys is closely related to the appearance of the defect in steels with a carbon content of less than 0,20 per cent; 72 per cent of all the defects were present in this type of steel. Most of the remaining defects were found in steels with a carbon content of more than 0,60 per cent, where the nitrogen content was substantially higher than in the lower-carbon steels. It is suggested that the defect arises from the combined effect of oxygen. nitrogen, and hydrogen. Its occurrence in low- and high-carbon steels is triggered by the formation of subcutaneous blowholes when the critical oxygen level for carbon monoxide blowholes is lowered by the presence of excessive amounts of hydrogen and nitrogen respectively.

Jan 1, 1984

By S. Jeon, J. Kim, H. Lee

Though the importance of the engineering rock mass properties such as deformation modulus, cohesion and friction angle is emphasized, the researches on the reliability of these values are rarely performed. By using modified Takagi-Sugeno (TS) fuzzy inference system, a fuzzy model was developed based on the data obtained from domestic tunnel construction sites, and the ability of prediction was compared with the empirical equations conveniently used for estimating these values, which finds that fuzzy model is better than empirical equation. Sufficiently large database, however, is required for training the fuzzy model for more accurate prediction. Obwohl die Wichtigkeit der technischen Eigentümer der Felsenmassen wie zum Beispiel Verformungsmodulus, Bindekraft und Reibungswinkel betont werden, wird die Forschung auf der Zuverläßigkeit dieser Werte selten durchgeführt. Mit modifiziertem Takagi Sugenos (TS) Flaumigenschlußsystem wird die Flaumigenmodelle von den Daten, die von inländischen Tunnelbaustellen erhalten werden, entwickelt. Zum Schätzen dieser Werte ist es viel günstig, Flaumigenmodell zu benutzen, als zu adoptieren die empirische Gleichung für die Fähigkeit der Voraussage. Genügende große Datenbank wird aber zum Ausbilden flaumigen Modells für genauere Voraussage erfordert. Quoique l'importance sur la caractéristique d'ingénierie de la masse de roche comme le module de déformation, la cohésion et l'angle de friction, soit soulignée, la recherche sur la confiance de ces valeurs est rarement effectuée. Avec le système modifié de Takagi-Sugeno(TS) fuzzy inférence, le nouveau modèle fuzzy s'est développé. Après avoir estimé sa valeur, nous pouvons savoir que ce modèle fuzzy, basé sur les données venant du chantier de construction de tunnel national, est mieux que l'équaton empirique. Pourtant plus de données de base sont indispensables pour produire le modèle fuzzy plus précis.

Jan 1, 2003

Book review Burkin, A. R. (ed.) . Leaching and reduction in hydrometallurgy. London, Institution of Mining and Metallurgy, 1975. £10. hydroxide pyritearsenopyrite NIM reports Report no. 845 A n electron-microprobe study of the nickel distribution in a serpentinite from Volspruit, Potgietersrus. (22nd Oct., 1969; re-issued Dec. 1975). Report no. 1546 Pilot-plant smelting campaign on iron ores from Tete. (22nd May, 1973; re-issued Jun. 1976). Report no. 1557 Cost estimates for the production of pig iron in the Tete district of Mocambique. (18th Jun., 1973; re-issued Jun. 1976). Report no. 1600 Dilute-acid leaching of slag from Tete ore. (20th Nov., 1973; re-issued Jun. 1976). Report no. 1602 The roasting of Tete slag for the extraction of vanadium. (20th Nov., 1973; re-issued Jun. 1976). Report no. 1635 Magnetic separation tests on Tete slag and ore. (30th Apr., 1974; re-issued Jun. 1976). Report no. 1671 Pyrometallurgical retreatment of a slag for the recovery of vanadium. (11th Oct., 1974; re-issued Jun. 1976). Report no. 1785 Some thermodynamic aspects of systems relevant to the flotation of sphalerite. Report no. 1808 Spectrophotometric determination (with pyrocatechol violet as chromogenic agent) of aluminium in zirconium metal and in the residue from anodesludges. Report no. 1813 The economic potential of some pegmatites from the Kenhardt area in relation to the trace-element content of their border zones. Report no. 1817 The rapid determination by X -ray-fluorescence spectrometry of tungsten in tungsten ores and concentrates. Report no. 1820 The thermodynamics of the formation of chlorocomplexes of iron (III), cobalt (II), iron (II), manganese (II), and copper (II) in erchlorate medium.

Jan 8, 1976

Professor R. N. Pryor, AR.S.M., B.8c., C.Eng., F.I.C.E., F.I.Min.E., F.I.M.M., who died on 14th July, 1979, after a short illness, was President of the Institution of Mining and Metallurgy for the session 1978-1979. Weld pool metallurgy A high level of current interest in welding characteristics and behaviour and in the properties of welds was amply demonstrated by the large attendance at The Welding Institute's 1978 Conference on 'Trends in Steels and Consumables for Welding' and by the overwhelming number of papers offered for the International Conference on 'Arc Physics and Weld Pool Behaviour' in May 1979. Mine ventilation The First International Mine Ventilation Congress was held in September, 1975, in Johannesburg, South Africa, at the University of the Witwatersrand. It was organized by the Mine Ventilation Society of South Africa. Occupational accidents and diseases The IXth World Congress on the Prevention of Occupational Accidents and Diseases will be held in Amsterdam from 6th to 9th May, 1980. Rock mechanics The 21st U.S. Symposium on Rock Mechanics is to be held at Rolla, Missouri, from 27th to 30th May, 1980. Protection against noise An International Symposium on the Protection of Workers Against Noisewill be held in Dresden (German Democratic Republic) from 27th to 30th November, 1979. Management of mineral resources A joint meeting of the Institution of Mining and Metallurgy, the Society of Mining Engineers of AIME, and the Metallurgical Society of AIME is to be held in London from 27th to 30th May, 1980. INFACON 80 During 1970 various South African institutes and associations agreed to organize an international ferroalloys congress. It was recommended that this should be made a continuing forum, where ferroalloy people could meet and discuss matters of mutal interest.

Jan 1, 1979

By F. G. Hill

The paper reviews the restrictions imposed by the Department of Mines (now the Department of Mineral and Energy Affairs) on the surface use of ground that has been undermined at shallow depths (down to a depth of244m). The reasons for the restrictions are discussed, with special reference to the early records kept by the Department of Mines on subsidence and fracture of the surface. A discussion of the nature of the strata overlying the ore-body, and the effect of undermining, is followed by a detailed account of investigational work, particularly since 1970, on the stability of shallowly undermined ground. The significance of the data collected during the investigations is considered next, with special reference to the social and economic implications. These are so farreaching, that it is proposed that the already flexible approach of the Department of Mineral and Energy Affairs in considering what structures may be built on undermined ground should become even more flexible. To this end, the appointment of a Commission is proposed to collect as much information as possible on the stability of ground undermined at shallow depth, and to revise the current overrestrictive conditions or guide lines that are in use.

Jan 1, 1981

By Dick Stacey

Many open pit mines are now being mined at very significant depths, often at depths far greater than was originally planned. Even deeper open pits are also being planned, to depths that would be considered deep by underground standards. The heights of the resulting rock slopes are usually beyond the current experience and knowledge base. The exceptions are, perhaps, some very high and steep natural rock slopes. These natural rock slopes are also assuming greater significance owing to pressures of infrastructure development and consequent exposure of such infrastructure to the hazards of slope failure and landslides. Developments in road and rail infrastructure are also resulting in higher rock cuttings. Present understanding of the mechanisms of slope behaviour and failure for high slopes, and for slopes subjected to high in situ stress conditions, appears to be lacking. If the mechanisms of slope behaviour are not well understood, the validity of commonly applied methods of analysis of the stability of such slopes may be questionable. The papers in this specialist International Symposium, including papers on mechanisms and monitoring techniques, and case studies will contribute to the understanding of these issues. The Symposium has attracted good international participation, from both the attendance and authorship points of view. We are very grateful to all presenters and delegates for taking timeout of their very busy schedules to come and share their knowledge and we hope that all will benefit from this event. Thanks are due to the Organising Committee and to the members of our International Advisory Panel for the ideas, the contacts and the badgering, and to the Secretariat of the South African Institute of Mining and Metallurgy for the organisation.

Jan 1, 2006

By J. A. Voster

Premier Mine (a part of De Beers Consolidated Mines Ltd) which is situated 38 km to the east of Pretoria, has the largest known diamond pipe in South Africa. The mine started operations in1903. The Premier Mine kimberlite pipe is unique in that it is intersected by a 75 m thick gabbro sill at a depth of 400 m below surface. The current mining method used is mechanized panel retreat caving, which has been successfully used to extract ore from the different mining blocks. All caving at Premier Mine is below the sill and failure to exercise good draw control could cause the early ingress of gabbro waste. Draw control at Premier Mine is crucial as it aids in preventing conditions of isolated draw, which results in the early ingress of waste, compaction of the kimberlite and the loss of ore reserves. To assist, an underground vehicle monitoring and control (VMAC) system was installed to enable the effective management of the draw control function. The system has evolved graduallyin collaboration with a local developer. The data accumulated is used to decide the most effectivedraw point loading pattern in order to achieve sound draw control principles. This is achieved as each load can be related back to the draw point of origin. The VMAC data recorded also relates back to specific load-haul-dumps (LHDs), tunnels, ore passes, as well as indications of dates, times and payloads recorded. An interface exists between the VMAC and a draw control linear program. Premier Mine’s VMAC system is not a ‘dispatch’ system but rather a draw control system that caters for Premier Mine’s specific block cave requirements. Premier Mine has realized that successful automation is not dependent on technology alone but rather on the successful implementation thereof.

Sep 1, 2001

Cutting strong rock with a drag bit assisted by high-pressure water jets By M. HOOD. B.Sc. Hons. (Min. Eng.). B.Sc. (Mech. Eng.). A.M.I.M.M. (Visitor) Experiments are described that led to the discovery that coherent high-pressure water jets directed immediately ahead of drag bits while they are cutting strong rock reduce the magnitudes of the forces on the bits significantly. Tests were carried out to assess the effects of the pressure of the water jets on bit-cutting performance. The pressure was varied between 10 MPa and 50 MPa, the water flow rate being a constant 30 I/min. Over this pressure range, the force on the bit was reduced to the extent that the depth of cut of the bit was at least doubled with the point of impingement of the jets optimized. Forces on the bit were found to be particularly sensitive to the point of impingement of the water jets relative to the bit. The optimum configuration was found to be with two jets, one directed towards each corner of the bit and impinging on the rock approximately 2 mm ahead of the leading edge of the bit. Experiments in which a drag bit and high-pressure water jets were used to cut strong abrasive quartzite in the underground mining situation have demonstrated a potential increase of up to five times in the average depth of cut due to reduction of the forces on the bit. The results from the underground tests indicate that the life of the bit is improved significantly - by a factor of approximately two - when highpressure water jets are used.

Jan 11, 1976

By R. J. Davidson, V. Veronsee

Some of the parameters affecting the elution of gold from freshly loaded activated carbon using pure water as an eluant were studied. The procedure involved pretreatment of the gold-loaded activated carbon with a strong reagent of sodium cyanide and sodium hydroxide, followed by elution of the gold with water. Gold-loaded carbon obtained from three different sources was studied. It was shown that the elution temperature was the most critical parameter, and column operation at I !OCC (gauge pressure of 50 to 100 kPa) is suggested. The effects of variations in the concentration of sodium cyanide required for the pretreatment of loaded carbon and of variations in elution flowrate were also investigated. Both these parameters were found to have only a marginal effect on the efficiency of gold elution. The investigation also indicated that gold-elution rates were affected to a considerable degree by the particle size of the carbon concerned. Higher elution flowrates could be used when carbons of finer particle size were eluted. A modified eluate-collection procedure was also developed during the course of the investigation. Oven-drying of the loaded carbon was shown to have little or no effect on the efficiency of the subsequent gold elution. The calcium and silica contents of the various carbon samples were also determined. It was immediately evident that the calcium content was very considerable in the case of loaded carbons originating from carbon-in-pulp operations. Calcium concentration was particularly high where air agitation had been employed in the carbon-contacting circuit. To some degree, the calcium build-up explains the serious carbon fouling taking place, resulting in a decreased efficiency of gold adsorption. The fouling problem was found to be less severe when mechanical agitation was used. No poisoning by calcium carbonate was observed where the pregnant solution had been acidified before it was contacted with the carbon.

Jan 1, 1979

By K. -J. Shou

A special three-dimensional boundary element method has been developed for the simulation of the development of fracture zone in rock mass. This approach comprises a boundary element method and a three-dimensional tessellation mesh generator. By using the tessellation generator, a set of pre-defined potential fractures is defined, and the fractures activate when the failure criterion is exceeded. This approach is justified by the reproduction of features observed in laboratory simulations of fracturing in blocks of rock subjected to compression. An attempt is then made to explain some of the attributes of fracture zone surrounding underground openings. Eine spezielle drei-Dimesionen Grenze Element Methode ist entwickelt zu simulieren die Entwicklung der Fraktur Zone in der Steinmasse. Diese Untersuchung benutzt eine Grenze Element Methode und ein drei-Dimensionen tessellation Masche Generator. Durch das Benutzen des Tessellation Generator, ein Satz der vor-bestimmt potentielle Fraktur ist festgelegt. Die Fraktur wird betaetigen, wenn das gescheiterte Kriterium ist uebersteigt und sind in dem Verscheiben-Abbrechen Element eingeschlossen. Diese Untersuchung ist von der Reproduktion der Fraktur justiert, die ins Labor beobachtet wird, um die Fraktur in der von der Kompression unterworfenen Steine zu simulieren. Ein Versuch ist gemacht, um einige Eigenschaften der Fraktur Zone um die untertageoeffnung zu erklaeren. Une méthode tridimensionelle spéciale de élément frontière a été dévélopée pour la simulation du dévélopment d’une zone fracturée dans la massive roche. Cette approche comprend une méthode de élément frontière et un générateur de maillage de la mosaïque tridimensionelle. En utilisant le générateur de mosaïque, une série des fractures potentielles predéfinies est définie avec d’une procédure de la triangulation de Delaunay. Les fractures activent lorsque le critère de rupture est dépassé et sont inclues dans les éléments du déplacement discontinuité. Cette approche est justifiée par la reproduction des caractéristiques observées dans le laboratoire, les simulations des blocs de roche fracturé et sujetés en compression. La tentative est alors fait pour expliquer quelques arttributs d’une zone fracturée alentours les ouvrages soustérrains.

Jan 1, 2003