Search Documents

By K. Hanumantha Rao, A. Nayak, K. S. Narasimhan, S. N. Mahapatra

B.A. Hancock It is not at all surprising that causticized potato and potato derived amylopectin starch solutions performed much better than their parent starches. Some preparation is required to rupture the starch granules to effect the polymeric adsorption and interparticle bridging necessary for selective flocculation. In laboratory work comparing the deslime performance of causticized and autoclave cooked laboratory corn starch solution preparations, it was found that higher deslime weight rejections, with attendant proportionally greater iron unit losses, occurred with the causticized starch. These results may be specific to the ore involved but they do suggest that cooking and causticizing cause different starch granule rupture and/or starch breakdown, which have an effect on desliming response. I calculated from the data in the article that the slimes product grades were high - 24.3% and 20.3% Fe when 53.7% and 54.5% Fe concentrate products were obtained, respectively, in Table 4, and 21% Fe with a 62.6% Fe concentrate in Table 5 - using the natural tailings sample, which had a head of 34.3% Fe. It may be advisable for the authors to consider different starch preparations in future investigations. The combination of upgrading and selectivity results presented in Table 4 are not as good as the authors suggest. The authors' claim that a system has been developed to produce saleable concentrates from the Kudremukh tailings is quite disconcerting. There are many hurdles yet to be crossed before commercial application of selective flocculation becomes possible because differences between the very small-scale laboratory tests conducted and commercial application are rather large. Among the many differences are varying circuit feed grades that will occur from use of tailings, the apparent face that much lower tailings grades will be encountered in practice (it is much easier to achieve a high concentrate grade with reasonable recoveries using 34.3% Fe tailings as in the study rather than 25.3% Fe tailings grades that the plant apparently averages), the hydraulic nature of the thickeners used in operations compared to the static system used in laboratory tests, the different size distributions that will be obtained from a plant closed grinding-classification circuit, and differences in water used in a plant operation and the laboratory. The authors wrote that it was necessary to overgrind to be sure that the coarse gangue would not settle with the iron oxide floccules. This situation is likely to be exaggerated in commercial operations where it is assumed cyclones would be used for classification. Because cyclone classification is greatly influenced by particle densities, there will probably be an even greater difference in size between the iron and gangue particles in the plant, which would make the gangue slightly coarser still in relation to the iron. This would make the selective flocculation-desliming separations using the procedure employed by the authors even more difficult and, using the dispersant system the authors employed, greater overgrinding would be required. To grind finer to minimize the coarse gangue in the flocculated iron oxides is quite inefficient and appears not to broach the problem. The actual problem appears to be insufficient dispersion of the ground pulp. In this situation, addition of a dispersant would likely be required to attain a sufficiently high pulp dispersion level to efficiently effect a selective flocculation-desliming separation. Although the very coarse particles would still have a tendency to settle with the floccules, it probably would be found unnecessary to overgrind as much as indicated. Use of an optimum combination of dispersant and pH modifying reagents may also significantly improve the selectivity of desliming. Additionally, although it is possible that sufficient dispersion may be obtained by pH control alone in some situations, it is quite probable that added dispersity was obtained in the reported work from using distilled water. It is research experience that distilled water enhances dispersion. In commercial operations it may not be expected that sufficient dispersion will be obtained by pH control alone, unless the water used in the process is by nature quite dispersive. Overall, a change in the Kudremukh tailings dispersant scheme appears necessary where a dispersant is used in conjunction with a pH modifying reagent. With this change, different dispersion-flocculation responses will result that would have to be further evaluated. Therefore, it is still an open question whether an efficient and effective selective flocculation separation using Kudremukh tailings may be obtained that will produce saleable concentrates.

Jan 9, 1986

Safety is the No. 1 concern of any drill contractor or mine operator. Everyone in the industry knows a safe site helps stabilize operational costs and enables higher productivity. When it comes to exploration drilling, research has proven a majority of injuries are caused by the mishandling of coring rods. A driller helper will typically handle up to 50 rods per shift or up to 15,000 rods per year. With an annual 340 t (750,000 lb) in rods managed by hand, the risk of serious injury is extremely high. Because of this, the top request from the exploration industry is diamond rod handling. The Boart Longyear 4200 surface exploration drill, slated for release in 2009, will give the industry a hand-free, operationally safe rig.. Developed through the collaboration of its global drilling services and products divisions and targeted at the 1,200-m (3,900-ft) NQ market, the upcoming Boart Longyear 4200 surface exploration drill features the safest and most flexible rod management sys-tem in its class. The rig includes the industry?s first, truly hands-free rod handling system. This increases operator safety on the jobsite. In addition to the rod handler, the rig also features many new innovations that boost productivity and rig efficiency while minimizing the risk of downtime due to component failure or operator error. Boart Longyear has also included an intelligent PC-based operating system designed to allow complete drilling control as well as diagnostics reporting for the rig.

Jan 1, 2009

By V. A. Leach, J. R. Johnson

The calculation of the dose to the bronchial epithelium, lungs and other body tissues from exposures to airborne radon and thoron daughters requires a knowledge of the pattern of deposition in the respiratory system and clearance from it. Exposure to radon or thoron daughters is measured in units of Working Level Months (WLM), which is independent of the aerosol particle size, the fraction of daughters that are attached to the aerosol and the degree of disequilibria between the daughters, and age and breathing rate of the subject. These factors will influence the deposition and clearance, and hence dose. It is therefore of interest to find the relationship between WLM and calculated dose as a function of aerosol size, unattached fraction, and disequilibria, and of age and breathing rate, and to define ranges for these parameters for which WLM is an acceptable measure of the risk. This presentation briefly reviews the two dosimetry models being considered by a current Nuclear Energy Agency (OECD) Working Group, and using these models, defines limits on parameters for which the WLM is applicable.

Jan 1, 1981

By W. Collingwood

As open pit mines continue to grow deeper and productivity continues to increase, the management of respirable dust and noxious gases can become a challenge. The natural wind flow in open pit mines is often recirculatory. This recirculation traps dust and gases in deep open pit mines. This problem is particularly acute in high latitude open pit mines due to a phenomenon known as an atmospheric inversion. In the winter, arctic and subarctic regions experience short days and long nights. This deficit of solar radiation creates a situation in which cold, still air accumulates near the bottom of the pit. In open pit mines, this can result in unhealthy accumulations of gases and other contaminants in the open pit mines. In this study, the natural wind flow patterns in and around open pit mines were investigated using a computational fluid dynamics (CFD) program. Two dimensional models were created for a variety of pit geometries. The effect of depth, slope angle, and wind speed on the recirculation pattern in the pit was examined.

Jan 1, 2011

By J. C. Stankus

To protect mine personnel and moving equipment at underground roof fall areas, mine operators typically install steel sets, which are covered with wooden blocks and backfilled with an expanding type cement material. In large roof falls, the cost of void backfilling becomes prohibitively high causing some mines to leave the voids open. However, the durability of wood over time and the capability of the steel set and wood lagging to resist falling rock are unknown. This has caused concerns for the Mine Safety and Health Administration (MSHA) and ground control engineers. During past two years, Keystone Mining Services, LLC designed and developed various impact-resistant steel set designs that were approved by MSHA and installed in various underground fall rehabilitations. This paper presents the patent pending impact-resistant steel set design methodology, including (1) steel set design per AISC national standard, (2) design, development, and laboratory testing of a water proof composite impact resistant lagging panel, and (3) impact resistant steel set design based on Law of Conservation of Energy. Two underground cases will be included detailing the application of the system.

Jan 1, 2011

By D. Mohapatra

Extraction of Al(III) from aqueous sulfuric acid solutions into organic Cyanex 272®-carbon tetrachloride systems was investigated from a multi-component mixture containing aluminum, cobalt and nickel. Al(III) extraction efficiency was quantitative with 1.0 M Cyanex 272® in two stages at an aqueous: organic (A:O) phase ratio of 1:1 and an equilibrium pH of 3.2. The stripping of Al(III) from the loaded organic (LO) with different acids indicated sulfuric acid to be the best stripping agent. More than 99% stripping of Al(III) from the LO was achieved using 2 M H2SO4 at an A:O phase ratio of 1:1 in a single stage. The stoichiometry of the extracted species of Al(III) was determined by the slope analysis method. The extraction reaction proceeded via the cation exchange mechanism and the extracted species was assumed to be AlA3?3HA, where HA refers to the dimeric and A the anionic form of the extractant, Cyanex 272®. The extraction of Al(III) was studied in the presence of various ions to ascertain the tolerance limit of individual ions.

Jan 1, 2008

For the past four years, the Department of Mining Engineering at the University of Kentucky has conducted a validation study of the CFD Fluent code, by comparing its results against mining-related benchmark experimental data provided by NIOSH?s Pittsburgh Research Laboratory. This particular study is dedicated to the effect of machine-mounted dust scrubbers on the performance of face ventilation systems using extended-cut mining with a blowing curtain.

Jan 1, 2009

By A. Nieto

A dump edge and vehicle proximity warning system is being developed at the Colorado School of Mines using GPS and wireless local area networks to improve the safety of off-highway trucks in open pit mines. After two years of research, software development, and testing in the laboratory, field tests are currently being carried out at operating limestone quarries and open pit mining operations to evaluate the effectiveness of the system under rugged operating conditions. This paper describes the progress made on this NIOSH-funded project and discuss, tests carried out recently, at the Morenci open pit copper mine in Arizona.

Jan 1, 2002

By Keith Schaeffer

This paper presents a history of the planning, engineering and construction completed for the railroad tunnel crossing part of the West Elizabeth Avenue Storm Drainage Project, undertaken to relieve flooding within the West Elizabeth Avenue area in Linden, NJ. The Railroad Crossing Contract is part of the larger Linden Drainage Improvements Project consisting of a new gravity storm sewer system. The improvements are required to provide additional storm drainage for the City of Linden and the Merck Pharmaceuticals manufacturing facilities in the City of Linden.

Jan 1, 2008

By Gary E. Slagel

The year was 1974. The event - the United States Congress was embroiled over what issues should be included in the proposed national surface mining law. The question - what should be done with underground mines? The leading bills ultimately addressed the environmental impacts associated with underground mines including provisions to protect the surface from subsidence impacts. Amid the fears that this subsidence language might discourage underground mining, sponsors of the bill were asked to explain the meaning of the provision that read "to prevent subsidence to the extent technologically and economically feasible." Was this an attempt to limit mining that caused planned and controlled subsidence? Former Deputy Director of the Office of Surface Mining, Dean Hunt, reviewed some of these historical events in a 1985 presentation before the Eastern Mineral Law Foundation. He reported that in 1974 Congressman Morris Udall took the floor to respond to these concerns expressed by other members of Congress and the industry. Mr. Hunt cited Congressman Udall's July 10, 1974 Congressional Record statement: "The House bill contemplates rules 'to prevent subsidence to the extent technologically and economically feasible.' The word prevent led to fears expressed by the Secretary of the Interior Morton, that the effect would be to outlaw longwall mining, with its obvious subsidence ... in fact the bill's sponsors consider longwall mining ecologically preferable and it and other methods of controlled subsidence are explicitly endorsed." Further, the report that accompanied the front-running bill, HR11500, provided the following clarification on the issue of subsidence prevention: "It is the intent of this section to provide the Secretary with the authority to require the design and conduct of underground mining methods to control subsidence to the extent technologically and economically feasible in order to protect the value and use of surface lands. Some of the measures available for subsidence control include: (1) leaving sufficient original mineral for support; (2) refraining from mining under certain areas---or (3) causing subsidence to occur at a predictable time and in a relatively uniform and predictable manner. This specifically allows for the uses of longwall and other mining techniques which completely remove the coal." It is clear from the preceding statements that Congress considered the removal of all the coal and causing subsidence in a predictable and uniform manner to be equal to or better than leaving support coal and causing no subsidence. While the actual provision in the bills talked of preventing subsidence, a subsequent exception made it clear that the real intent was to control it. This is evidenced in the specific planned subsidence language that appeared in the bills and ultimately in Section 516 (b) (1) of PL95-87, the Surface Mining Control and Reclamation Act. It reads: "...adopt measures...to prevent subsidence ... except in those instances where the mining technology used requires planned subsidence in a predictable and controlled manner..." In spite of this historic record that supports controlled subsidence, something has been lost in the implementation. The primary focus by many regulators over the past few years has been on the "prevent" aspect irrespective of mining method being used. This has appeared to change the original intent of Congress from one of controlling subsidence to one of minimizing damage. The objective of this report is to review some of the current regulatory issues that impede full extraction mining and offer some suggestions on possible ways to deal with these issues.

Jan 1, 1986

By A. Habibi

The ventilation survey was conducted in an underground longwall trona mine. The mine is relatively shallow and categorized as a gassy mine. The ventilation system consists of nine shafts (three intakes and six exhausts). Three surface based axial fans ventilate the mine configured in a blowing arrangement. Following the ventilation survey airflow quantity, frictional pressure losses and air psychrometric characteristics have been quantified. An accurate resistance survey has been conducted to calculate the pressure drop with regard to moving cages and skips in the shafts. This paper discusses the benefits of utilizing high accuracy digital pressure transducers and psychrometers in a ?leapfrogging? survey to gather data needed to build the computer ventilation model. Two underground booster fans with VFD are currently idle but available at the mine. The ventilation model has been used to determine the optimal booster fan locations to decrease the overall operating cost by reducing the load carried by the main fans. A leakage study has been conducted to evaluate the effects on the system of additional pressure from a booster fan. The study finally prepares a future ventilation model for the next fifteen years of mine operation and investigates the effect of proposed scenarios.

Feb 27, 2013

By Robert M. Valentine, Randall L. Lentell

Interpretive geotechnical investigations were performed for the construction of approximately 15,250 m (50,000 ft) of wastewater interceptor tunnels in Austin, Texas. Subsurface materials consist of claystone (or clay shale), siltstone, altered volcanic tuffs, chalk and limestone. Special conditions include multiple crossings of Onion Creek with cover ranging from about 1/2 to 3 m (2 to 10 ft.), and the potential for mixed-face conditions consisting of water-bearing gravels overlying clay shale or siltstone. The methods and results of the geotechnical investigations are discussed and the inferred construction conditions are compared to those encountered during tunneling. A suggested format is presented for interpretive geotechnical reports for underground construction projects.

Jan 1, 1985

By Douglas B. Silver

Super Cycle future The final topic is mining?s future. The most important questions are ?How much longer is the Super Cycle going to last? What should we expect to see going forward? How will the Super Cycle end?? Three possible scenarios follow. Scenario one: Super Cycle has peaked Kathy Casey-Kirschling is officially the first Baby Boomer. She was born Jan. 1st, 1946. If you google ?first baby boomer,? she?s the one that shows up. A Baby Boomer is anybody born between 1946 and 1964. In the United States, it represents about a quarter of the population ? approximately 76 million people. The Baby Boomer generation is going to change the economics of the world because there are so many in the generation. A review of spending patterns indicates that the largest amount of discretionary spending occurs between the ages of 49 and 52. Retired people tend to live on fixed incomes so they have less discretionary income. They also tend to downsize their house, which may contribute to the housing glut and the need for a lot less metal. Therefore, the upcoming retirement of the Baby Boomer generation could result in a massive shift in economic spending resulting in the peaking of the Super Cycle. Figure 1 is an index graph from the Toronto Stock Exchange (TSX). The index has recently peaked. A lot of people see that as a sign that bad things coming our way. A careful review of different commodity prices also suggest that the peak has occurred and it does not seem to matter which commodity prices are considered. Copper prices have seen a peak as have nickel prices. Nickel and molybdenum displayed the same trend with a peak in 2005 as did zinc. Uranium, which has single-handedly tried to behave like the dot com craze, has also peaked.

Jan 1, 2008

By Gary J. Fletcher

Mining and processing activities which are proposed on private land, state leases, or unpatented mining claims are governed by numerous local, state, and federal laws which identify the procedures and conditions which must be met before resources can be developed. The respective government agencies responsible for the administration and enforcement of these laws have promulgated supporting regulations and guidelines, and have implemented certain permit and approval processes to ensure compliance. Each exploration project has a unique environ- mental setting and location which further dictates the types of air, water, hazardous waste, and wildlife laws and regulations which must be complied with before development commences. The environmental planning process should be the first step in the evaluation of existing company properties and the potential acquisition of other mineral properties. However. many company don't consider the environmental requirements for a project until the decision is made to develop the property for mining and processing. If a mining company wants to expedite the environmental planning process, it must first develop an in-house process for evaluating the project and determining the environmental approval procedures in the state where the project is located. The first stage of environmental planning involves general information which can set the overall company philosophy for development of projects.

Jan 1, 1987

The MineSight Schedule Optimizer (MSSO) is a new production scheduling tool developed by Mintec, Inc. using mixed integer linear programming (MILP) techniques. This tool was developed to solve the short- and medium-term schedule problems for surface and underground mining operations that involve multiple mining areas, multiple processes, multiple destinations and blending requirements. MSSO finds the optimum schedule in each period that achieves the objective while satisfying comprehensive product quality and quantity requirements as well as physical and technical constraints. Using the MineSight Planning Database (MSPD) as a central data hub, MSSO seamlessly works with MineSight 3-D (MS3D) block models and third-party data, MineSight Interactive Planner (MSIP), MineSight Haulage (MSHaulage) and MineSight Activity Planner (MSAP) to prepare data, formulate MILP models, calculate, report, fine-tune, save and visualize schedules. This paper presents the features and capabilities of MSSO. A case study is also given to demonstrate the applications of this new tool.

Jan 1, 2009

By R. P. King

The MODSIM mineral processing plant simultor is used to find optimal combinations of target separation specific gravities in a typical modem coal washing plant. A plant that is set up with these optimal targets can deliver up to 10% more yield at the same ash content as the same plant set up with separation targets chosen by conventional methods. MODSIM is the only simulator currently available that can simulate the liberation of pyrite and other mineral matter during open- and closed-circuit grinding operations. The simulator can therefore be used to assess the benefits of grinding operations in the flowsheet.

Feb 24, 1997

By G. Gaidajis, K. Angelakoglou

The development of a tool for assessing the environmental sustainability of mining facilities is described in this study. The tool is based on the analysis of basic components of the examined system, i.e., the quantities of the incoming materials and outgoing wastes, their hazardousness and scarcity, the utilization of water and energy resources, and the biodiversity. The developed tool provides both qualitative and quantitative assessment of the environmental performance of a mining facility in a broad time scales (past-present-future) and is easily applicable from non environmental experts. Moreover, relative software is developed to further support the application of the methodology. The implementation of the tool is expected to lead to an improved understanding of the environmental performance of a mining facility and more importantly identify the areas of significant environmental concern. However, based on feedback from industries, a number of shortcomings of the approach have been identified so far and are presented, indicating further actions for the advancement of the proposed tool.

Jan 1, 2011

By K. Hanson

When done properly, benchmarking is an extremely effective tool for assessing ones performance, finding areas for improvement, and identifying strengths. However, when done improperly it can be an exercise in futility and result in incorrect observations and conclusions. A primary pitfall of benchmarking is collecting too much unreliable information. Surprisingly, the evolution of data storage and the ease of data collection are not helping with better data collection. Instead, it is just allowing one to collect more information, while at the same time inundating one with too much data. Additionally, the process of data collection can be tedious and is often times delegated to the least experienced individual resulting in unreliable and incorrect data collection and entry. Another primary pitfall of benchmarking is metrics that are cost based or poorly designed. Cost based metrics typically involve comparing unit mining costs ($/tonne). Between mines, unit mining costs are not very well correlated and have become further complicated by significant regional cost variations and mining inflation in the last years. Likewise, poorly designed metrics lead to poor benchmarking results. Examples of poorly defined metrics include: metrics that rely on information that is difficult to collect, metrics that are poorly defined, metrics which are too site focused, and metrics that measure low consequence practices.

Jan 1, 2011

By A. Wahab Khair, John G. Oldsen, John C. Stankus, Song Guo

During the last several years, implementation of trusses, in lieu of wood cribs, has been successful for supplemental tailgate support in the Pittsburgh seam. This paper reviews, the truss support system provided by the new high strength 0.6" tensioned cable truss, which is now also being used in cribless tailgates. Cable loading and roof deformation were monitored to evaluate roof and floor performance. The test results indicate that the cable truss system successfully controlled the roof and floor during the first and second panel extraction. This paper will describe the advantages of cable trusses and their load transfer mechanism as well as mine evaluation.

Feb 24, 1997

By J. B. Gwiazda

Introduction Thick seams constitute a considerable portion of Polish coal reserves. In producing mines and those under construction, the reserves where the height is more than 4.5 m (15 ft) total about 24% of all the hard coal reserves. The reserves that are under urban and industrial areas can be extracted using stowing methods for surface protection. About 50% of thick seam reserves can be extracted by caving methods. Thick seam mining methods Thick seams are usually extracted by multilift methods. There are some methods of thick seam mining that generally can be divided into caving and stowing methods. The stowing method is more expensive, but must be used when mining to protect surface features. The more known methods of thick seam mining include • extraction of thick seam in ascending order with stowing ; • thick seam mining in descending order with consolidated stowing; • thick seam mining with gob consolidation; • thick seam mining in descending order with roof caving ; • sublevel caving thick seam mining system; and • thick seam mining system using an artificial roof. Thick seam mining with introduction of an artificial roof The most advantageous method of thick seam mining is the method using an artificial roof. The artificial roof usually consists of wire mesh. Such wire mesh must be durable and must prevent small rock fragments from passing through. The mesh is usually made of steel properly protected against corrosion. The artificial roof is placed on the coal floor of the top slice (Fig. 1). Caving rock falls on the artificial roof and is thus separated from the coal. The next slice is extracted under the artificial roof. The producing face of the next slice must progress within 10 m (33 ft) behind the front of the first slice. As the second producing face progresses, the wire mesh moves down on the coal floor and may be used as an artificial roof for the next slice. Thus, one artificial roof allows the extraction of several consecutive slices. Application of the artificial roof allows for clean extraction and reduces coal losses. It also eliminates the hazard of spontaneous combustion. Introduction of the artificial roof has been limited due to a lack of artificial roof laying equipment. Manual laying of wire mesh is a labor-intensive operation, and it delays face progress, resulting in poor productivity. To eliminate these problems, artificial roof laying equipment was designed at the Polish Central Mining Institute. The support and the method of laying operation is covered by a patent. Artificial roof laying powered support To extract thick seams using an artificial roof, four-leg shield supports with lemniscate linkage were developed (Fig. 2). This shield is used in the first top

Jan 3, 1987