Search Documents

By Richard V. Good, John B. Harvey, Lloyd S. Jones

INTRODUCTION The term "Rapid Underground Excavation" is generally associated with high speed tunnel advance with large volumes of excavation, and indeed this is the type of work for which most of the recent innovations in methods and new machinery have been developed. However, the term applies as well to any underground excavation process that results in an earlier project completion than would be expected with conventional methods, and hopefully with a decrease in total unit excavation cost. Often significant progress has been made during the primary stages of an underground construction project and then an inordinate amount of time and effort has been expended on small units of "miscellaneous" excavation which has delayed the overall project completion and escallated overall unit costs. Construction at the Nevada Test Site of the Atomic Energy Commission for underground testing frequently requires significant amounts of so called "miscellaneous mining" such as short access drifts, cross cuts, alcoves, niches and concrete keyways. Many of the keyways must be excavated without disturbing the rock beyond the excavation lines and construction scheduling often dictates that much of the work must be accomplished without disturbing sensitive electronic equipment already installed. In order to cut down on lengthy and costly delays required for the tedious manual excavation of much of this miscellaneous mining, a market search was made for suitable mechanical excavation equip-

Jan 1, 1997

By P. N. Psarropoulos

During many strong earthquakes in the past, a significant number of tailings dams failures has been recorded, leading in some cases to human life losses. However, over the last decades, seismic design of tailings dams has drawn much attention mainly due to the high environmental hazard. Although the stability of such geostructures under dynamic loading is mainly related to their liquefaction potential, there exist several technical issues that have not been adequately investigated. One of these issues is the impact of local site conditions on the dynamic earthquake stresses developed, and therefore on the inertial instability of these dams. Based on the models examined in the first part of the present study (Stability of Tailings Dams ? Part I: Static Loading), two-dimensional numerical simulations are performed in order to examine the effects of local site conditions in the dynamic response of tailings dams. Imposing dynamic loading via characteristic pulses and real earthquake records, the most commonly used types of construction methods are studied at their final stage. Emphasis is given on the special characteristics of the ground motion, while the material nonlinearity of both soil and tailings is taken into account by an equivalent-linear procedure. The results obtained indicate that local site conditions may have a significant impact on the seismic response of a tailings dam.

Jan 1, 2005

By L. Stas

The authors have been interested in stress measurements in the rock mass for a long time. This paper describes the development of new apparatus for stress measurements in a rock mass. The principle of stress measurement by this device is based on the relief method as applied on the conical shaped surface of the bottom of a borehole. The design started based on the experience of K. Sugawara and Y. Obara who have been using the compact conical borehole over-coring system (CCBO). The conical shape of the strain gauge probe CCBO makes the fixation of the probe in borehole easy and, also, makes the measurement of stress in independent directions possible. The principle of the measuring method, the preparation of the borehole, the design of the probe for continuous measurement of stress during the course of overcoring are described. Also, a simplified version of the probe for long term monitoring of stress variations in the rock mass by means of the inserted body method and the initial laboratory results and in-situ testing of the development sample are described. Additionally, testing was done regarding the possible glues in relationship to the creep effect for this case.

Jan 1, 2006

By D. Royston

Curved pulp lifters have been incorporated in SAG and AG mills in Australia. The aims have been to ensure complete discharge, at high throughput, of both slurry and coarse solids, especially at high mill rotational speeds. Curved pulp lifters can overcome incomplete discharge and back-flow of solids down the pulp lifter that can occur in straight-radial pulp lifters (and is a major cause of wear). They can be designed to prevent reverse flow of pulp via grates back into the mill. Experience with curved pulp lifters now extends to three years over three mills, in one mill as an installation from new and two as retro-fitted installations. Curved pulp lifters, relative to conventional designs, offer improved discharge and wear performance and well as high impact-resistance and wear life of the curved pulp lifter grates.

Jan 1, 2000

By Mark L. Munsell

In recent years, miners have tried many approaches to maintenance such as: - Highly sophisticated computerized programs. - large planning groups designed to preplan and schedule work. - Contract maintenance. - Break down maintenance. Each of these approaches has faced the added constraints: - High replacement cost of equipment necessitating longer useful equipment life - management?s increased scrutiny of all indirect costs such as maintenance. Faced with these factors, what system of maintenance control is right? After visiting many properties recently, it appears there is no right system. Maintenance programs need to be tailored to the people and production constraints that occur at an individual property.

Jan 1, 1976

By Sukumar Bandopadhyay

A present dominant problem is that of high downtime of the longwall shearer used in the coal production process. The means by which this problem can be overcome are many, but one of, the most important ones is that the-use of an expert system can reduce diagnostic and repair time. In this paper, a fault-diagnostic expert system model is presented. Specifically, the diagnostic architecture of the longwall shearer expert system and its use for diagnostic reasoning are discussed.

Jan 1, 1989

By B. K. Mishra, R. K. Rajamani

This paper focuses on the use of a numerical tool known as the discrete element method (DEM) to study the motion of ball charge in ball mills. DEM is employed to simulate the motion of individual balls. While doing so, the effect of liner design on the grinding performance of the mill is studied. Two important, factors, such as the configuration of the liner and the geometry of the lifting surfaces, are correlated with the overall mill performance. An attempt is made to show the effectiveness of the lifter bars in transmitting power from the mill shell to the interior of the mill, with particular emphasis on large diameter mills.

Jan 1, 1994

By Dwayne C. Kicker, Duk-Won Park

As the use of longwall mining increases in the U.S.. there is a need to better understand the stress redistribu- tions indicative of this method. To control high stress concentrations, the yield pillar concept has been developed. A physical longwall mine model has been designed to study the effect of yield pillars in deep mining. The model in- cludes sensitive stress measuring devices, a new excavating technique, and a new model material. This study includes the use of both regular and yield pillar systems and has successfully simulated the mode of stress change in chain pillars.

Jan 1, 1986

By Sol Ribakoff

In 1973, the Subcommittee on Contracting Practices, U. S. National Committee on Tunneling Technology, National Academy of Sciences, under the able chairmanship of A. A. Mathews, Engineering Consultant, now residing at Kaunakokai, Hawaii, undertook the task of developing recommendations for improving the performance of underground construction work, reducing the costs of such work and minimizing the adverse atmosphere in which owners and contractors were performing their respective functions. The author of this paper and C. F. Palmetier, a highly qualified engineer, were thereupon appointed as staff assistants to the Subcommittee, to conduct a study of existing practices and relationships in Western Europe and in the United States, to formulate recommendations, for consideration by the Subcommittee and the participants in a future workshop, as to desirable improvements in United States contracting practices and relationships. The study, conducted during 1973 and 1974, involved personal interviews of a total of 162 owners, engineers, contractors, lawyers, and educators throughout the United States and in 7 European countries, the analysis of 178 replies to questionnaires sent to individuals and firms involved directly or indirectly in construction, and a workshop, near Napa, California, attended by 53 representatives of all segments of the construction community. The resulting report, entitled "Better Contracting for Underground Construction", was submitted by the Subcommittee to the National Academy of Sciences, which approved its publication in 1974 by the National Technical Information Service. It may be obtained from that Service at Springfield, Virginia, 22161, as Accession No. PB-236 973. It was recognized-during the course of the study that while contracting practices and owner-contractor relationships were the

Jan 1, 1981

By H. Verakis

A fire in a coal mine conveyor belt entry represent a major safety and health risk to miners. Fighting belt entry fires can be a commanding effort. If there is a failure of one aspect in the fire fighting needs such as a dissimilar hose-valve connection, then it can result in the inability to extinguish a fire. Fire incident data compiled over nearly 30 years for underground coal mines shows that fires in belt entries account for 15-20 percent of the total number of fires. Fires in the belt entries of coal mines have resulted in injuries and fatalities. New regulations have been promulgated that require an unplanned fire not extinguished within 10 minutes of discovery to be reported to the Mine Safety and Health Administration (MSHA). A fire that is not extinguished within several minutes may take hours or days to extinguish or may require sealing a section or the mine in some cases. The current fire protection regulations in the U.S. Code of Federal Regulations (CFR), Title 30, Part 75 are designed to prevent or control the fire hazards present in a belt entry. These requirements and other factors affecting belt entry fires are discussed, including fire detection and warning, fire suppression devices, type and location of fire fighting equipment, waterlines, and cleanup and removal of combustible materials. The fire suppression systems used to extinguish/control a belt fire and the effect of ventilation on the propagation of conveyor belt fires are also discussed.

Jan 1, 2009

Land management planning is an important issue in all jurisdictions, especially as it relates to mineral development. These planning documents are prepared at different intervals and reflect the realities at the time that they were prepared. The Seven Questions to Sustainability developed during the North American Process of the Mining, Minerals and Sustainable Development (MMSD) project are proposed for the evaluation of Land Use Plans as they relate to Mineral Development. This paper provides the background to the Seven Questions to Sustainability and how it can be applied to the evaluation of land use plans with specific reference to Resource Management Plans developed by the U. S. Department of the Interior?s Bureau of Land Management in Nevada. While this paper is focused on Nevada, the approach is broadly applicable and may be used in other planning regimes.

Jan 1, 2007

By Rogério C. Guimarães, Antonio E. C. Peres

Arafertil's oxidized ore presents barite grades that oscillate between 5 and 12%. The barite separation plays a major role in the production of apatite concentrates for the manufacturing of phosphate fertilizers. The selectivity, via flotation, in the system barite-apatite is inherently difficult due to the similarity of the physical/chemical characteristics of these minerals. The evaluation of the relevant aspects of this separation was performed based on the determinations of the electrical surface charge of barite and apatite, the abstraction isotherms of cetyl-stearyl sodium sulfate and fatty acids soaps for barite and apatite, microflotation in a modified Hallimond tube, and flotation tests in a batch column. The results showed that the adsorption of cetyl- stearyl sodium sulfate occurs preferentially onto barite, in comparison with apatite. On the other hand, the rice bran oil soap presents similar adsorption levels onto both barite and apatite. The cetyl-stearyl sodium sulfate was selective as a barite collector in the presence of apatite, a fact that was not observed in the case of rice bran oil soap.

Jan 1, 1999

By Peter Fordham

A Norbridge review of 25 top mining companies highlighted financial problems for many firms. To better understand these results, Norbridge benchmarked 17 mining companies to understand the problems that companies face, the methods being used to improve performance, and the results that have been achieved. The study indicates that many mining companies in three sectors-coal metals, and non- metallic minerals-have implemented new strategies to improve performance. Many of these strategies supplement traditional initiatives with two types of process improvement efforts, facility-specific and company-wide, to help generate performance gains. The study compares the results of these strategies in each sector. INTRODUCTION imes are tough in the mining industry. Norbridge reviewed financial results of 25 top mining companies for the past 2 years-seven coal companies, twelve metals companies, and six non-metallic minerals firms.*The study found that 40% lost money in 2002, and * Coal companies include Alliance Resource Partners, Arch Coal, Consol Energy, Massey Energy, North American Coal, Peabody Energy and Westmoreland. Metals producers include Barrick Gold, Cleveland-Cliffs, Coeur d'Alene, Falconbridge, Freeport McMoran, Grupo Mexico, Inco, Newmont Mining, Noranda, Phelps Dodge, Placer Dome, and Teck Corninco. Non-metallic firms include Florida Rock, IMC Global, Martin Marietta Materials, Oglebay Norton, PotashCorp and Vulcan Materials. Information is from public sources, e.g., annual reports, company Web sites.

Jan 1, 2004

By M. Balakrishnan, K. A. Natarajan, J. M. Modak, J. S. Gururaj Naik

The ability of various fungal species isolated from gold mines to uptake gold and base metals such as zinc, copper, iron and lead from gold-process cyanide effluents was investigated. Under identical treatment conditions, different strains showed wide variations in their ability to take up gold and other base metals. Aspergillus terreus exhibited as high as a 60% gold uptake. Almost complete removal of zinc was possible with various fungi and with the yeast Saccharomyces cerevisiae. Studies at various metal concentrations showed a higher gold uptake from dilute solutions, and studies with Aspergillus niger showed that gold uptake by living cells increased gradually as the contact time increased. Metal uptake capacities between living and nonliving cells were also compared. A waste biomass (ABM- I), obtained from a fermentation industry, wasalso identified as having a high gold uptake capacity. At 5% (W/v) solids, ABM-I could efficiently remove up to 83% of the gold contained in an effluent solution within 24 hrs.

Jan 1, 1995

By E. M. J. A. Pallone, F. N. Cunha, W. S. Resende, R. M. Stoll, R. C. Bradt

Utilization of the magnesium aluminate spinel in refractor' applications is briefly reviewed. The synthesis of a magnesia aluminate spinet aggregate from natural raw materials is considered in terms of the crystal chemistry of the spinet structure and expected impurities. Principles for the formation of this spinet refractory aggregate from different natural raw materials are presented. The basic concepts were then applied to the reaction of a bauxitic clay with a natural magnesite. This combination of raw materials has the potential to produce a low-cost refractor' aggregate that is a composite of spinel and forsterite. Experimental results are reported to produce a spinel refractor.' aggregate containing a small amount of forsterite. It possesses low apparent porosity and high bulk density suitable for industrial refractor' applications, including steelmaking, aluminum and copper foundries and cement production.

Jan 1, 2002

By James N. Prudden

Measurable physical characteristics of placer deposits include geological, geomorphological, sedimentological and mineralogical features which produce the complimentary ingredients with which one can formulate an economic evaluation of these complicated deposits within the confines of a well established geological model. Heavy mineral suite composition and character will change downstream from the provenance area and will compliment the related depositional environment. Careful attention to gold particle characterization during the exploration phase can indicate new source additions, enhance deposit evaluation methods and greatly assist in maximizing metallurgical efficiencies. Failure to recognize and measure these important features very frequently leads to frustrated and unrewarding placer evaluation goals. Increased general acceptance of sedimentology in the gological appraisal of ore bodies has progressed into the science of clastic sedimentalogy using measurable parameters to evaluate minable units. This branch of geology has developed as a tool in locating, defining, and mining alluvial concentrations of valuable heavy minerals. The repeatedly successful application of this valuable tool in conjunction with other classical geological methods can be directly related to the development of a geological model which formulates the distribution of detrital gold. This use of multiple geological techniques permits the transfer of routinely derived data to management. Standardized nomenclature permits the transmission of uniform information thereby promoting credible property evaluation. This approach enables organizations to critically assess large numbers of potential mining targets for definitive feasibility studies. Sedimentology must play an integral role in the evaluation of any alluvial deposit. The sampling problems associated with particulate gold are well known and frequently cause perplexing evaluation problems. Consequently, properly directed and executed

Jan 1, 1987

By G. Hargrave, K. W. Moloney, M. R. Stokes

In recent years drivage advance rates in the UK have in- creased from 35m per week in the 1980's to 100/150m per week possible today. These extended rates of advance have resulted in an increase in the potential methane, dust and heat generation at the drivage face. In order to disperse this additional pollutant load requires an increase of fresh air at the face. Although advance rates have changed, current auxiliary ventilation practice has not. UK mining law requires that the fresh air must be delivered to within 5m of the face. This has lead to the wide spread use of overlap auxiliary systems, since a pure forcing system set at this distance would lead to excessive airborne dust. UK mining law does not at present consider on-board mounted exhaust scrubber fans to constitute an effective overlap fan within mechanised drivages. In an attempt to determine whether working conditions could be safely and economically improved within mechanised drivages, a series of preliminary full scale gallery trials were con- ducted. A summary of the principal findings of these trials are presented together with an outline of a series of representative CFD simulations, scale model experiments.

Jan 1, 1997

By C. M. Chang, H Gu, J. A. Barrera-Godínez, T. J. O’Keefe

The inability to economically separate Fe3+(aq) from a variety of liquid effluents is a major Concern for the primary metals industry. A unique solvent extraction process, galvanic stripping, has been developed to address this problem. The galvanic stripping of iron from D2EHPA using only a 5~10 g/L H2SO4 solution is achieved after Fe3+ is directly reduced to Fee, in the organic phase using zinc metal additions. To date, the primary focus of the laboratory research has been on optimizing the parameters that control iron removal. The results from these studies have now been, used to make a preliminary design for a continuous flow process that is envisioned for zinc industrial applications. Specific quantitative data are shown for the use of a Zn-Ph cellos° in the iron-reams al process. Some introductory results on electrochemical potential measurements and impurity distribution with solution cycling are also giiven.

Jan 1, 2000

By C. R. Stephan, N. B. Greninger, W. A. Slivensky

The U.S. Bureau of Mines and the U.S. Mine Safety and Health Administration (MSHA) are participating jointly in a research program to evaluate strength characteristics and air-leakage resistance of various proposed seal designs for use in underground coal mines. Over 20 full-scale seals were constructed in the Bureau's experimental mine at the Lake Lynn Laboratory, air-leakage tested, then subjected to pressure pulses of 0.14 MPa or greater. A discussion on the experimental procedure, construction techniques, and the explosion and air-leakage test results is presented. Four types of construction material were used during this seal testing program: solid-concrete-blocks, low-density foam blocks, cementitious foam, and wood blocks. Only one of the solid-concrete block designs using a mortared thick wall survived the explosion and air-leakage tests. Most of the low-density foam block and cementitious foam seal designs were judged to meet the requirements to be considered a coal mine seal. One of the wood block convergence seal designs failed explosion testing. Based, in part, on these research findings, several alternative seal design constructions using low-density foam blocks, cementitious foam, or wood have been approved by MSHA for use in coal mines.

Jan 1, 1993

By R. G. Eggert, M. R. Walls

A mining CEO's willingness to participate in risky investment opportunities significantly affects a company's strategic-investment decisions. Decision-analysis techniques provide a mechanism for measuring a CEO's risk tolerance and ability to make formal comparisons of risk propensity among mining firms. The authors developed a methodology for measuring CEO risk tolerance. The findings from a confidential survey of mining CEOs are presented. The results from the survey suggest that: •mining CEOs are overwhelmingly risk averse when considering investment decisions; •CEOs of small mining firms are significantly more risk averse than CEOs of large mining firms; and •there appears to be some differences between Australian and non-Australian CEOs regarding their willingness to participate in risky investments. The results of this survey suggest that CEOs are pursuing objectives other than, or in addition to, maximizing shareholder wealth and that they act to reduce the financial exposure associated with strategic investments.

Jan 1, 1997