Search Documents

By M. Gershon

Four computerized approaches for coal blending are described and their strengths and weaknesses are explored. Spreadsheet analysis Other than word processing, spreadsheet software is the most commonly used software. Its wide availability and ease of use are two desirable features that have led many to try to adapt it to the purpose of coal blending. These are the two main advantages of this approach. To use a spreadsheet for coal blending, each row of data represents one source of coal. Each column represents a quality of the coal, with the last column specifying the tonnage of that coal in the blend. The calculated figures are. the blended qualities, which can be programmed to appear in the bottom row. A trial-and-error approach is then used to develop the best blend. Inserting any blend in the last column provides the blend characteristics at the bottom of the page. If any specifications are not met, the blend can be changed, all calculations being immediately updated. This process is repeated until all specifications are satisfied. A third advantage of this method is that it is exactly the procedure that one would go through if doing this by hand. With a spreadsheet, many more blends can be evaluated in much less time, allowing the designer to try to improve over satisfactory blends to find the best of them. The resulting improved blends or cost savings are a fourth advantage of this approach. There is only one major disadvantage of using the spread- sheet. This is that most probably the best blend is not found. As an inexpensive introduction to computer-assisted blending, which can be easily understood and cost just a few hundred dollars, this is a recommended place to begin.

Jan 1, 1987

By Taneomi Harada

Mine drainage has high acidity and sometimes contains more than the allowable concentration of ionized iron. In such a case, mine drainage is neutralized with calcium carbonate and calcium hydroxide to separate precipitates, such as the iron hydroxide and gypsum generated. Currently, most of these precipitates are not utilized and are accumulated in tailing dams. As a result, the service life of the tailing dams is reduced. This becomes a matter of concern, since securing sites for such dams is difficult. A most effective means of solving this problem would be to promote utilization of these neutralized precipitates. This paper reports on the results of studies on neutralized precipitates produced at the old Matsuo Mine (Iwate Prefecture), which has the largest neutralization treatment facility in Japan. As a result of the studies, the following was proposed regarding application of neutralized precipitates. Utilization as ferrite: Mix ferrous hydroxide and ferric hydroxide in water to synthesize magnetite-like ferrite, to be used in the manufacture of magnetic markers for a mobility support system for blind pedestrians, or in producing magnetic fluids for sink-and-float separation of nonmagnetic metals and nonmetals. Utilization as hematite: Bake ferric hydroxide to produce hematite, thereby extracting metallic iron for paint pigment as well as for the manufacture of ironware by local industry. Production of aluminum sulfate: Precipitate aluminum ions from water and add sulfuric acid to produce aluminum sulfate.

Jan 1, 1995

By Joseph M. Keane

Introduction The English word "sedimentation" is derived from the Latin verb "sedere" meaning to sink down. As a mineral processing unit operation, sedimenta¬tion has been defined as the separation of a suspension into a supernatant clear fluid and rather dense slurry containing a higher concentration of solid (Brown, G.G. 1960). Sedimen¬tation has been historically subdivided into thickening, which has the primary purpose of increasing the solids content of one of the thickener prod¬ucts relative to the feed stream, and clarification, which has the primary purpose of removing solids from the feed stream to produce a product essentially free from particu¬late matter. There is no absolutely precise distinction between these subdivisions and in certain applica¬tions, both objectives can be accom¬plished. Major Design Factors The capacity of conventional metal¬lurgical sedimentation devices is a function of slurry throughput and its attendant settling rate. Important factors, recognized by early investigators (Taggart, 1972), which influence the settling rate of a given metallur¬gical slurry include: Feed dilution or solids-liquid weight ratio Size and shape of the particulate solids Specific gravity differential between the solids and liquid phases Presence of electrolytes and/or flocculants Pulp viscosity Slurry temperature In addition to the foregoing histor¬ical factors, recent investigators have noted (Pearse, M.J., 1977) that other parameters which may have an influence upon settling rate and, thereby, thickener performance include: Method of flocculant application Particle size distribution Particulate wetting characteristics Feeding arrangements Rake speed and type Existence of convection currents Wind disturbance Evaporation All of the above factors should be examined and the effect upon thick¬ener performance brought about by manipulating the factor over the expected operating range should be determined if performance optimization is desired.

Jan 1, 1986

By Ian M. Loomis, Malcolm J. McPherson

A fuel-rich fire exists when the quantity of fuel exceeds the oxygen available to support complete combustion. The transition of a mine fire from Oxygen- rich to Fuel-rich combustion, at this time, represents a point-of-no-return in the fire fighting efforts. Once the transition has been made to fuel-rich the fire can spread at a rate 6 to 10 times as fast as in the oxygen-rich state. Utilizing available technology the fire fighters are left to seal the fuel-rich fie as the only technique to extinguish it. In order to minimize the devastating effects of a fuel- rich fire it is important to understand the means by which the fire becomes fuel-rich and by what means the fire may be returned to an oxygen-rich state. This paper covers: the development mechanism of a fuel- rich fire in a coal mine entry and the physical and chemical effects of applying water to a fire. Experiments concerning these matters have been conducted in a 30 cm square wind tunnel constructed at the Virginia Polytechnic Institute and State University as a model coal mine entry. This paper also addresses the results obtained in testing application of a water mist to fuel-rich fires in this model. These tests have centered on the development profile of a fuel-rich fire in a duct and demonstrate a means of regaining control of a fuel-rich fire by returning it to an oxygen-rich state.

Jan 1, 1995

By Young C. Kim

Determination of the minimum sampling requirements of the run-of-mine (ROM) coal is very important for the purpose of meeting contract specifications. It is also important for the purpose of meeting emission regulations at a coal-burning power plant, such as the one located at Homer City, Pa. The classical statistical sampling theory can be applied to this problem, if ROM coal samples are known to be spatially (or serially) uncorrelated. On the other hand, the estimation variance concept from the Matherson's geostatistics must be used, if the samples are spatially correlated. Conditional simulation technique combined with simulation of the existing mining method is used to determine under which circumstances ROM coal samples do not preserve the spatial correlation. Only after establishing the degree of correlation that exists among ROM samples, an optimal sampling scheme can be devised using either the classical statistics Or the geostatistics. The minimum required sample volume can then be calculated using the well-known Gy's formula. This paper describes the results of the above investigation using the Helen coal mine data of the Homer City Owners. Empirical guidelines for determining the degree of correlation are also provided for coal mine operators.

Jan 1, 1986

By Malcolm J. Lake, P. Brad Marchant, Linda M. Broughton

Thiourea is recognized as a technically competitive alternative to cyanide for gold and silver extraction for a variety of ores and concentrates. This paper describes the results of a recent mini-pilot locked cycle test comparing cyanidation with acidothioureation treatment of gold bearing sulphide concentrate. The gold extractability of both methods was similar. The comparative metallurgical operating conditions and test results are summarized. Detailed byproduct solution analyses and environmental toxicity test results are presented and suggest that thioureation might result in acutely toxic byproducts even after treatment. Comparative process economics are summarized based on preliminary commercial operating flowsheets derived for the locked cycle case study. Capital and operating cost estimates are shown. The results indicate that cyanidation is more economically favorable within the constraints of the case study. Considerations for process selection between thioureation and cyanidation, for conceptual case studies, are discussed.

Jan 1, 1998

By R. J. Sweigard, R. V. Ramani

Productive and beneficial use of reclaimed surface-mined land is a concern of industry, government, and the general public. A process has been developed that will aid mine planners and public planners in the evaluation of postmining land use potential. This process involves the application of site planning principles to surface-mined land in a way that ensures productive end use of reclaimed land. The process consists of 10 basic components and is iterative in nature. Termination of the process depends on the amount of data collected and the evaluation requirements of each mining site. The analysis centers around the economic, environmental, and social impacts of the alternative land use plans.

Jan 1, 1987

By Robert Snow, Francisco Sotillo

Six types of amines were evaluated in the cleaning step of the rougher concentrate for the Crago “Double Float” process in terms of relative selectivity. Selectivity of these amines was ranked based on both batch and locked cycle flotation tests. Two parameters were used for selectivity ranking, the Selectivity Index, SI, and the ratio of insol rejection to the tailings weight percentage, R*. The comparison of the flotation results of the batch tests of the cleaning step of the Crago process for an unsized amine feed generated the following ranking from the most selective to the least selective mine: Quaternary > Primary [ ]Tertiary [ ] Condensate > Ether > Secondary(?).

Jan 1, 2002

By Cindi Byrns, Andy Davis, Amy Tisdale

The Robinson district, Ely, Nevada is a hydrogeologically complex system with several distinguishable geologic blocks, each with a distinct background groundwater chemistry. To discriminate between background and mine-impacted groundwater, background wells, monitoring wells, pit lakes, waste rock seeps, and surface water samples were analyzed for a suite of major cations and anions, together with trace and precious metals, rare earth elements, 2H-deuterium and 18O/16O. The data allowed identification of groundwater flow paths, verification of hydrochemical source areas and characterization of natural attenuation mechanisms (e.g., mixing, dilution and mineral precipitation) that control the concentration and migration of metals at the site.

Jan 1, 2000

By S. K. Das

A detailed strata-mechanics investigation and examination was carried out in the E2 Panel (ML-II/7) of the XVI Bottom coal seam, which is located in the Moonidih Colliery of B.C.C.L., Jharia coalfield, India. Above this panel, the XVI Top coal seam was previously worked out by a longwall panel. Based on intensive field study and on experiments in a number of longwall panels located within various Indian coal mines, the actual behavior of the coal roof strata was evaluated and new strata-mechanics concepts around the longwall panels were developed. These concepts resulted in new methodologies concerning the behavior of roof rocks, caving characteristics, etc. within longwall panels and in the area of strata mechanics. Based on these new strata-mechanics concepts, a very simple, but realistic, model was developed to determine the optimum capacity of the powered supports. This model considered the combined loads resulting from the detachment of strata and composite layer blocks from the face and, also, loads due to the deflection of strata and composite layers situated above the detached roof rockmass. This formula, along with the other related formulas by the author, prompted the determination of the optimum capacity requirement for the powered supports to be used in the XVI Bottom coal seam, located under the worked out area. This new concept in strata mechanics and capacity requirements of the powered supports in a longwall face may be an aid to Mining Engineers.

Jan 1, 1997

By A. L. Boerner

Off-highway tire costs represent a significant portion of the total mining costs in openpit, truck-shovel operations. To extend the lives of tires, the site-specific factors influencing tire life should be investigated Valuable data can be obtained by combining historical operational data captured by a mine dispatch system with detailed tire and maintenance histories. Assuming that failure counts satisfy a Poisson distribution, F-tests can be applied to determine significant deviations from desired or target counts. The methodology developed in this paper can be used to identify the haul routes and loading and dumping zones that have significantly higher incidences of tire failure. Corrective action can then be targeted at these zones by modifying the shovel or truck operator practices; changing the haul route maintenance and clean up practices; or altering the bench, ramp or waste dump design parameters. An example is given of the correlation of tire separation and tire impact failures with haul routes for a fleet of nine Caterpillar 793C trucks in operation at the Chuquicamata Mine in northern Chile. A high incidence of impact failures was observed for the ex pit ore crusher and for tires installed in the left outer rear position on the trucks. The latter was postulated to be due to a preference for drivers to execute right-hand turns prior to dumping. Recommendations were made to revise crusher and dump cleanup practices and investigate the feasibility of super-elevating the surface of dumping zones to reduce ground pressure on the left rear tires.

Jan 1, 2002

By Zhongxue Li, Shuang Gao, Zhixin Zhen, Yiqing Zhao, Xuan Qin

If not well-managed, a mine-tailings facility may become a major source of risks, endangering the community and environment, and damaging the reputation of the minerals industry regarding sustainability. Identifying, characterizing, and mitigating the hazards and risks associated with tailings facilities have been critical to the maintenance of community-safe and environmentally sound mine-tailings facilities. Herein, a complex network model for characterizing the hazards and risks associated with the lifecycle of tailings facilities is presented. In this approach, the hazards are modeled as vertices of the complex network, and the interactions among the hazards are modeled as edges of the complex network. The complex network for modeling the hazard and risk spreading of mine-tailings impoundments is analyzed and characterized by using network metrics such as the network density, geometrical characteristics, characteristic path length, network efficiency, and clustering coefficient. The degree distribution of the network obeys a power-law distribution, indicating that the network for characterizing the risk spreading associated with a tailings facility is scale-free. According to the results of calculations and existing research results, the network is ultrasmall-world. By analyzing the change of the global network efficiency under four kinds of different methods to remove network nodes and edges, network nodes with higher between centrality (BC) are identified as critical. The removal of those critical nodes helps mitigate risks associated with a tailings facility and reveals the vulnerabilities to BC attacks.

Jan 1, 2017

By H. W. Seany

Over the years since the initial experiments with underground concreting were made in 1956, attesting to cope with the ground weight and pressure encountered in the development of a large-scale underground block caving system, the use of monolithic concrete linings has grown to include most of the primary development in the, mining area. Although the development cost of concrete linings is higher than either timber or steel-supported openings, the repair and maintenance costs are substantially lower, making concrete the most economical means of ground support. Other advantages are also apparent, in that concrete provides superior fireproofing, better ventilation, and a safer, cleaner working place.

Jan 1, 1965

By Byron Belew, Juris R. Harlamovs, D. B. Dreisinger, John L. Watson, G. A. Kordosky, Thomas O. O’Keefe

Unwanted impurities, present in raw materials, are often coextracted along with desired constituents during leaching. Due to its abundance and ease of extraction, the presence of ferric iron in leach solutions, solvent extraction circuits, and subsequently in electrowinning circuits, has always been a problem. In the case of zinc hydrometallurgical processing, iron is frequently an impurity in leach solutions. Purification of such solutions by solvent extraction, using di (2-ethylhexyl) phosphoric acid (D2EHPA) in a kerosene diluent, results in ferric ions being readily extracted along with zinc into the organic phase. Ferric iron has proven difficult to strip from the organic phase, but it is known that ferrous iron may be easily stripped from D2EHPA, and hence a process to effect reduction of iron present in the organic would have great potential. This research investigated a process to directly reduce ferric to ferrous iron in the organic phase, and to strip the ferrous iron using a dilute acid solution. The process utilized metallic zinc as the reductant and a low concentration sulfuric acid stripping solution. The results of the laboratory tests illustrated that iron could be readily removed from the organic phase by simultaneous direct reduction and acid stripping. The reductive stripping process was subsequently utilized in industry at the laboratory and pilot plant levels. The results of the industrial tests were encouraging and demonstrated the potential of this novel concept.

Jan 1, 1993

By V. D. Ayurov, N. O. Kaledina

The coal mines monitoring should be based on the usage of simple and evident models, letting in the total unity to reflect a structure of organization of mine, system ability of its construction and specific character of its functioning. Such models are offered to create on the basis of extracted hierarchies of objects of mine. All objects of mine are broken on levels of technological hierarchy. For objects of each level of hierarchy there are made balanced models of entering and leaving material flows. Then these balanced models are coordinated among themselves by the help of the inter hierarchical relations. So the structured-qualitative characteristic of the object of monitoring, reflecting in a kind of the table structure of formation of material flows on mine, their intensity and measure of transformation is formed under transition from one level of hierarchy of mine to another. An example of real us- age of hierarchical balanced models on mine is given. The mathematical models of coal mine monitoring should reflect objective laws of their structural organization and functioning. Therefore under the constructing of mathematical models it is important such a way to reflect a structure of the mine organization, that in totality the models has been reproduction of system ability of its construction. The knowledge of the separate parties of functioning of mine, reflected in particular mathematical models, should "to be packed" in combined unity. Or else, they should be connected in system, convenient for recognition by the person. Considering the mine, the expert allocates multi-dimensionality of the objects of making its elements. He always has the knowledge of laws of development of mining work that is connected with pithy stratification of researched object. In dependence of sparial-temporary level of abstracting there are allocated the horizon, wing of a mine field, layer, panel, extracting face, longwall in coal mine. The human thinking on each of these levels operates with a set of concepts peculiar to him, characteristics, definitions.

Jan 1, 1996

By S. K. Kawatra, S. A. Moffat, K. A. DeLa’O, T. C. Eisele

It was observed that the efficiency of some autogenous grinding circuits was dependent on temperature, with the energy-efficiency of the grinding process decreasing in the winter months, accompanied by an increase in critical-size production. Several possible causes of this phenomenon were suggested, including: • Increased brittleness of the ore during blasting in the pit at low temperatures, leading to increased levels of internal cracking that would lead to rapid breakage to critical size in the mill; •Brittleness changes of the rock in the mill; and • Changes in the durability of the rock caused by either formation of ice on the surface, or freezing of water inside the pores and cracks of the rock. To determine which mechanisms were occurring, drop tests were carried out using frozen and unfrozen rock with varying degrees of porosity, both dry and water-saturated, and which had been blasted for mining in summer and in winter. These tests showed that there was no difference between the summer-blasted ore and the winter-blasted ore, and that durability changes in dry rock over the temperature range from 25ºC to -25ºC were negligible. However, water-saturated rock showed an increased resistance to breakage upon freezing, particularly when the rock was highly porous, or when a layer of ice formed on the surface. Seasonal changes in the durability of rock in grinding are therefore due to formation of ice in and around the rock.

Jan 1, 1995

By E. W. Hawk

he power generation industry may be required to reduce carbon dioxide (C02) emissions if regulations related to global climate change are enacted. Coal-fired generation emits more than 80% of the power sector CO2 and would be a likely target for CO2 reductions. Compliance with the Kyoto Protocol will require a 33% reduction from the projected year 2012 emission level, even with moderate load growth. This article describes an analysis of power industry CO2 reduction options and their costs. It assesses how a generator would make compliance decisions under a mandatory CO2 emissions reduction program. Carbon sequestration, fuel switching and new plant construction are considered. The Global Climate Change Treaty signed at the Rio de Janiero Earth Summit in June 1992 set the long-term goal of stabilizing CO2 concentration in the atmosphere. The December 1997 Kyoto Protocol established short-term mandatory targets for the United States and 37 other developed countries. The United States' target is a 7% decrease by 2012 from the 1990 "greenhouse gas" level. Developing countries are exempted from reductions, according to the Kyoto Protocol, despite projections that indicate a significant increase in their emission levels. The Kyoto Protocol must be ratified by the US Senate. US power industry carbon emissions were 490 Mt (540 million st) in 1990 and are projected to be 680 Mt (749 million st) in 2012, according to the US Energy Information Administration. Coal-fired generation emits more than 80% of the power sector CO2. Assuming that the power industry is only required to reduce emissions by a proportional share, a 33% emission reduction, or 225 Mt (248 million st) of carbon, would be required to comply with

Jan 1, 1999

By A. F. Fossum, D. E. Munson

The U. S. Department of Energy is constructing and operating the Waste Isolation Pilot Plant (WIPP), a research and development facility near Carlsbad, New Mexico, to determine whether or not defense-generated high-level radioactive waste can be stored safely in bedded salt. The goal of the WIPP modeling program is to develop the capability to predict room responses from one site to another without a priori knowledge of the actual room responses. Data from one of the early WIPP excavations, called the South Drift, have already been used to form an initial evaluation of computational models for predicting room closures as a result of salt creep [Morgan et al., 19851. In that study, a significant unresolved discrepancy existed between predicted and measured room closures. It was suggested that future studies address alternate forms of the constitutive law. In this paper, an alternate form of the creep model for salt is used that is founded upon the deformation- mechanism map for the micromechanical deformation processes. This model embodies both steady-state and transient creep. Also, quasi-static plasticity is incorporated into the complete constitutive model for salt. The conclusion is drawn that the combination of the mechanistic creep model, plasticity, and flow potential can approximate the late time South Drift deformation. Further improvement of the model fit of plasticity in the future is expected to further improve the simulation.

Jan 1, 1986

By L. Patts, J. Hummer

The use of diesel-powered equipment in underground coal mines has increased substantially during the last ten years in an effort to enhance mine safety and productivity. Pennsylvania and West Virginia are two of a number of states with regulations governing the use of such equipment. These states both developed and promulgated regulations before permitting diesel equipment in their underground coal mines because of concern for miners’ safety and health, especially with regard to the contamination of mine ventilation air with diesel exhaust emissions. The major components of diesel exhaust emissions are combustion gases and diesel particulate matter. The gaseous emissions consist of carbon monoxide, carbon dioxide, oxides of nitrogen, sulfur oxides and unburned hydrocarbons. The diesel particulate matter (DPM) is comprised of solid carbon particles, liquid and solid hydrocarbons, sulfates and moisture. The Federal Mine Safety and Health Administration (MSHA) also promulgated regulations in an effort to control diesel emissions in underground coal mines. MSHA has adopted threshold limit values (TLVs) for all gaseous components of diesel exhaust, which were established by the American Conference of Governmental Industrial Hygienists (ACGIH). MSHA (30 CFR Part 72 Subpart D) has established a tailpipe DPM emissions limit of 2.5 g/hr for diesel engines used in permissible equipment, heavy-duty non-permissible equipment, generators and compressors used in underground coal mines. A tailpipe DPM limit of 5.0 g/hr has been established for light-duty outby diesel-powered equipment. The rationale for the tailpipe emissions limit was that an ambient measurement of DPM in a coal mine was not feasible because there is no established sampling method able to distinguish between coal mine dust and DPM. The stringent tailpipe emissions limit mandates the use of exhaust aftertreatment devices for most diesel engines used in underground coal mines today. One method by which tailpipe DPM can be reduced to MSHA limits involves using an exhaust cooling device in conjunction with a high-temperature, disposable diesel particulate filter.

Jan 1, 2011

By Samara Ali-Ahmad, Keith Hanks, Cindy Pham

The City of Los Angeles will rehabilitate approximately 9 miles of its North Outfall Sewer. This sewer was constructed in the 1920s as an unreinforced concrete semi-elliptical sewer. One of the methods for rehabilitation is to approach the sewer as a pre-excavated tunnel and install pre-cast segmental liners to provide a single pass corrosion resistant, structurally self sufficient project. The estimated cost for this project is $46 million. The project has completed the pre-design study, and the design is now underway.

Jan 1, 2003