Search Documents

By Stanislaw Wasolewski

Computerized systems for ventilation parameters monitoring which are used in Polish coal mines provide the ventilation staff with a great number of measuring data. These data can be used to get knowledge about dynamic properties of ventilation process and disturbances affecting its state. This is necessary to create a reasonable concept of mine ventilation control system and make a practical application of such system. In the paper a method of ventilation process identification with the use of measuring data from monitoring system is described. Computer analysis of time series including statistical, correlation and frequency methods are applied to estimate dynamic properties of ventilation process and its disturbances. Using the Fast Fourier Transformation (FFT) algorithm the parameters of the process have been obtained which can be efectively used in a system for mine ventilation control.

Jan 1, 1991

By Bhaskar B. Thapa, Michael T. McRae, Michael J. Teske, Richard M. Nolting

Packer test data and tunnel in?ow observations are used to show that the distribution of equivalent hydraulic conductivity obtained for a rock mass from borehole packer testing will be biased if the orientations of the planned tunnel and testing borehole differ. Furthermore, test results show that the distribution of equivalent hydraulic conductivity is different in various geologic sub-units at the same site. The impact on in?ow of the major uncertainties, including conductivity, head and specific yield, is illustrated to be amenable to a combined analysis using Monte Carlo simulation.

Jan 1, 2003

By K. N. Han, P. B. Queneau, Bruce W. Cavender

Measures of metallurgical performance, such as recovery rates or mass balances, are frequently based on point estimates of operating conditions in the system of interest. Because the processes being measured are dynamic, a range of uncertainty accompanies each measurement; this uncertainty is reflected in the accuracy with which the calculated result describes the true metallurgical performance. In stochastic modeling, a range of probable values is used in place of a point estimate to describe each variable. The calculated result takes the form of a distribution, delineating both the magnitude and probability of potential outcomes.

Jan 1, 1993

By J. Andrew Leach, Robert T. Tape, Thomas G. Harper

A practical approach to elope stability design of heap leaches up to 90 m (300 ft) high is presented based on recent experiences with heaps throughout the Western U.S. Shear strength parameters for foundations, ore and liner systems are considered, with particular attention given to frictional contacts between geomembranes and clay or geotextiles. Stability of both ore and containment dikes is discussed including the effects of seismicity, staged dike construction, progressive heap development and in-heap solution levels. Design criteria and methods of analyses are presented along with techniques for improving stability.

Jan 1, 1987

By E. J. Miller

The Ventilation Branch is engaged in a project to determine if low level carbon monoxide monitors used for early detection and warning of fire in a coal mine conveyor belt entry can provide protection equivalent to that of thermally actuated point type heat sensors commonly used for fire detection. A series of tests were conducted to determine the required operating parameters, such as sensor spacing and alarm levels of detected carbon monoxide to provide equivalency between' these methods of fire detection. This report summarizes the results of these tests.

Jan 1, 1980

By J. C. Cawley, J. Sottile, J. L. Kohler

Control circuit failures contribute significantly to continuous miner downtime. The time required to put the machine back into production is a function of the time required to diagnose the problem, obtain parts and make the repair. Of these, the diagnostic time is often the largest. A microprocessor-based system with the ability to diagnose all of the common control circuit failures was designed, installed on a continuous miner and tested. This paper summarizes the development of the diagnostic system and provides examples of the system's diagnostic capabilities. Implementation issues and the hardware used for the prototype are briefly described. Comments on the system's performance are also presented.

Jan 1, 1995

By W. H. B. Blackburn, D. M. S. Bhatia

Twenty-six in situ analyses of cubic galena crystals from a Mississippi Valley-type deposit were undertaken with a laser microprobe emission spectrograph to study the variation of nine trace elements from the crystal center to its periphery, both along the diagonal and vertical. The general trend is an outward increase in the concentrations of Ag, Ga, Ge and In, with As showing the opposite trend. Bi, Cd and Sn showed no discernable trends. Sb was not detected. These variation patterns may serve as a model for similar studies of other Mississippi Valley-type deposits.

Jan 1, 1987

By A. S. Moss, J. Linkous

Where difficult shaft sinking conditions exist, it may be appropriate to use a blind drilling technique. The success of the method is in part due to the presence of a drilling mud which fills the shaft void during excavation. The mud performs two important functions with respect to shaft stability: it reduces the influence of groundwater; and, due to the mud weight, gives a positive sup- port to the shaft walls. The application of the method is illustrated by a case history which traces the development of a shaft from the initial investigation to determine the shaft location, through the evaluation of wall stability and mud requirements, to the shaft sinking contract and actual conditions encountered.

Jan 1, 1986

By Heinz Hoberg, Fred Ulrich Schneider, Rudolf Diegel

The risk of contamination of dumped tailings and ground water by coal flotation reagents has been investigated by using the 14C-radiotracer method for adsorption and desorption measurements. The results indicate, that a high amount of the reagent components adsorbed on the tailings if there was no coal in the pulp. In coal flotation however a competitive adsorption behaviour could be observed, with the effect that only a low quantity of reagents adsorbed on the tailings. Mobilization tests showed, that only small quantities of reagents could be desorbed by rinsing water. Therefore the contamination of ground water should be low.

Jan 1, 1995

By John A. Herbst, William T. Pate, A. Edward Oblad

Dynamic optimization is a cost-effective means to increase production or improve product quality in a plant. Several model-based approaches to dynamic optimization of mineral processing operations have been developed and implemented in plants. This paper reviews the phenomenological models that are the basis for dynamic optimization and the alternative methods of mathematical optimization. These methods range from theoretically complex and costly to implement to intuitively comprehensible and readily implemented.

Jan 1, 1990

By J. Donald Rimstidt, Jeanette K. Jerz

Acid mine drainage is a major environmental problem worldwide. A key to remediating this problem is understanding the rate and mechanisms of the complex, multistep pyrite oxidation reaction under geologically relevant conditions. Because many waste piles are not submerged, a large amount of pyrite oxidation actually occurs in air. We have designed a Barcroft-manometer reactor to measure the rate of pyrite oxidation in air as a function of relative humidity and oxygen partial pressure. The reactor consists of two chambers joined by a manometer. Each experiment occurs at constant temperature, initial oxygen partial pressure, and relative humidity, although these variable can be changed between runs. Oxygen consumption was measured and pyrite oxidation rates were calculated from those data. Initial data indicate that rate of pyrite oxidation by oxygen in humid air is much faster than the rate of oxidation by oxygen in solution. The rates determined by this study can be used to develop better remediation techniques for acidic mine waters.

Jan 1, 2000

Geopolymerization is a process by which Al-Si minerals undergo dissolution and polymerization in an alkaline solution to form a monolithic material with a high mechanical strength (Davidovits, 1991, 1994). In this study, the factors affecting the geopolymerization of Na feldspar (albite) and K -feldspar (microcline) were investigated. It was found that both Na feldspar and K -feldspar are reactive in geopolymerization with the resultant geopolymers showing a high compressive strength. The leaching ability, the proper molar ratio of Si/Al in the geopolymeric gel phase and the higher average hardness of the undissolved particles remaining in the geopolymers are found to greatly affect the ultimate compressive strength of the formed geopolymers. Key words: Geopolymerization, Mineralogy, Albite, Microcline

Jan 1, 2003

By R. J. Sweigard, T. Beckman, C. T. Justice, E. D. Thompson, T. C. Hopkins

As a means of permanent disposal, fine coal refuse is often pumped as a slurry into surface impoundments. As the available volume is filled, the embankment heights are frequently increased. The additional embankment material is often placed upon consolidated fine coal refuse. There has been concern about the long-term effect of consolidation of this material at or above the liquid limit on its shear strength. A laboratory investigation was performed using three different types of fine coal slurry taken from central Appalachian coal-preparation plants. The refuse was consolidated in 3-m (10 ft) Plexiglas columns under incremental amounts of surcharge loading. The incremental loads were designed to simulate the effect of increasing the height of a refuse embankment on top of the consolidating coal slurry. After the refuse in the columns had consolidated for several months, the columns were cut apart, and triaxial tests were performed on both the consolidated and unconsolidated material for comparison of their shear-strength parameters.

Jan 1, 1998

By S. K. Kawatra, T. C. Eisele

Although column flotation is known to be more effective than conventional flotation for cleaning fine coal, little attention has been paid to the considerable sulfur removal potential of this process. Whereas conventional flotation can only with difficulty remove pyritic sulfur from coal, flotation columns can make this separation readily due to their greater selectivity. This project has used a modified flotation column to remove pyrite from fine coal. This column has been shown to be capable of removing 70 to 85 percent of the pyritic sulfur from coal while recovering 80 to 85 percent of the total calorific value. However, the remaining pyrite is too finely disseminated to be readily removed by physical means. Currently, experimentation is in progress using bacterially-catalyzed dissolution of pyrite in acid solution to remove ultrafine pyrite and aid in the removal of coarser pyrite inclusions.

Jan 1, 1988

By Daniel R. Hack

Mine planning software companies have recently focused some resources on the development of industrial minerals packages useful in the aggregate industry, which is years behind other mining industry sectors in the use of computer-based planning techniques. This paper presents and compares characteristics of aggregate / quarrying software packages currently on the market, each product having strengths beneficial under different circumstances. To be successful, the developers must confront the limitations of their packages under a variety of situations, address the unique characteristics of the aggregate industry, and pay particular attention to the applicability of their products in real situations.

Jan 1, 2002

By John E. Urosek, Herman Schade

In March, 1988, a fire occurred in a large underground coal mine. Coal Mine Safety and Health of the Mine Safety and Health Administration was immediately notified of the situation. They requested the assistance of the Pittsburgh Health Technology Center (PHTC) to provide monitoring and analysis of the mine atmosphere in and around the fire area to insure the safety of the miners escaping from the mine and for the miners involved in extinguishing the fire. The capability to provide this type assistance is maintained by the PHTC Offices located at 4800 Forbes Avenue, Pittsburgh, Pennsylvania. The equipment used is maintained field ready and can be mobilized almost immediately. This paper will discuss the response to this recent major mine fire.

Jan 1, 1989

By A. S. Mallicis, Li Xiawoei, P. W. Weiblen, I. Iwasakl

Platinum group metals (PGM) are often found in close association with arsenide and sulfarsenide minerals in copper-nickel bearing gabbroic rocks. Major losses of platinum in flotation have been attributed to the susceptibilities of the arsenic minerals to oxidation and subsequent losses of their recoveries in cleaner flotation stages. The use of a nitrogen atmosphere in grinding and in flotation, the effectiveness of activation for improving their floatabilities, and the role that electrochemical interactions play not only between grinding media and minerals, but also among different minerals, are discussed.

Jan 1, 1989

By C. J. Pritchard

Productivity improvements reduced the number of continuous miner sections from seven to three while maintaining full productive capacity. So a decision was made to test an advancing tailgate ventilation system on the shortwall mining section. Having the shortwall mine its own return air system has freed the third mining section for more productive, less costly mining. The advancing tailgate has provided effective ventilation across the face and gob with acceptable pressure losses. The low-productivity, tailgate-development, continuous-miner section has been transformed into to a high-productivity, development-retreat section that is also available for long-term mine development duties, increasing mine planning flexibility.

Jan 1, 1991

By S. N. Mukherjee

Maintenance of equipment in Longwall faces plays a vital role in face performance. This is more prominent when shortage of spare parts and trained personnel occurs. A study was made in an operating Indian Longwall face for identifying the types and meantime between failures. Though the duration was not enough and study was not very elaborate, it revealed certain interesting facts. The machine availability was found to be poor, though a maintenance schedule was followed. Failure of simple parts like AFC chain connectors even resulted in loss of production of 10 times the complete chain cost. This pinpoints that a proper maintenance schedule is to be developed considering the human factors and local conditions existing in the particular country. Operations research techniques could be used in the process.

Jan 1, 1989

By W. E. L. Minter

The most important Witwatersrand gold placers occur on extensive unconformity paleosulfaces that were produced during protracted periods of fluvial degradation. The erosional etches on what was generally unlithified sub-strate indicate that low sinuosity erosion patterns prevailed. The transport systems were dominantly braided fluvial with a minor debris-flow component. The placer sediments were non-cohesive sands and gravels. They were evidently transported by fluctuating, yet perennial, discharges across extensive, low relief braid plains, not far from littoral environments. Progress made in understanding heavy mineral transport processes now emphasizes the importance that selective entrainment probably had in producing concentrations. Cognizance that these characteristics are not unique to the Witwatersrand should be taken into account when designing exploration models.

Jan 1, 1991