Search Documents

By L. A. Hansen, D. L. Buffington, G. H. Beckwith

This paper reviews geotechnical engineering considerations in heap leach pad design, discusses design philosophy and provides design procedures. A brief discussion of surface water hydrology ground- water protection and other design considerations are also presented. Special emphasis is placed on projects in the arid and semiarid regions of the Western United States where annual evaporation exceeds rainfall, and where good foundation conditions are usually present.

Jan 1, 1987

By B. P. Spigarelli

To meet the growing need for CO2 capture and storage technology, Michigan Technological University is researching CO2 capture and storage using carbonate solutions. The objective of the present study was to increase the absorption rate of CO2 into the carbonate solution without reducing the absorption capacity of the solution. This approach used a polypropylene glycol methyl ether (PPGME) as a surfactant to chemically alter the gas bubble size. Experiments were conducted to study the absorption rate of CO2 at varying surfactant concentrations of 0, 0.12, 0.24, 0.36 and 0.48 g/L. Results showed that as the concentration of surfactant increased in solution, the absorption rate also increased. The CO2 absorption rate increased from 3.45 mmol/min CO2 at 0 g/L PPGME to 3.92 mmol/min CO2 at 0.48 g/L PPGME. This amounted to a 14% increase in the CO2 absorption rate with no decrease in absorption capacity of the solution.

By D. L. Romero

The Line Creek Mine is operated by Crows Nest Resources Limited, a wholly owned subsidiary of Shell Canada Resources Limited. It is located approximately 25 km north of Sparwood in southeast British Columbia (refer to figure 1). The Line Creek coal deposit is part of the Upper Elk Coalfield in the East Kootenays. The coal is a medium volatile, low sulfur, bituminous coal and is used as a coking coal. Coal close to the outcrop is typically of low F.S.I. and is processed for thermal use. The present pits have a total coal reserve of 30 million clean tonnes and is a multi-bench, open-pit operation. The coal is recovered by front shovel and backhoe combination, and hauled to the plant with a fleet of 120-tonne and 40-tonne capacity trucks. Line Creek is unique in that it can simultaneously treat both metallurgical and thermal coal in separate processing facilities (refer to figure 2). Run-of-mine coal is delivered to the truck dump. The plus 50 mm material is scalped off and reduced to minus 50 mm in two rotary breakers. The raw coal is then conveyed to one of five, 5000-tonne capacity, silos. Typically one silo is used for thermal coal and four for metallurgical coal (refer to figure 3).

Jan 1, 1991

By W. C. Patrick

The Spent Fuel Test-Climax (SFT-C) was con- ducted to evaluate the feasibility of retrievable deep geologic storage of commercially generated spent nuclear-reactor fuel assemblies. One of the primary aspects of the test was to measure the thermomechanical response of the rock mass to the extensive heating of a large volume of rock. Instrumentation was emplaced to measure stress changes, relative motion of the rock mass, and tunnel closures during three year of heating from thermally decaying heat sources, followed by a six month cooldown period. The calculations reported here were performed using the best available input parameters, thermal and mechanical properties, and power levels which were directly measured or inferred from measurements made during the test. This report documents the results of these calculations and compares the results with selected measurements made during heating and cooling of the SFT-C.

Jan 1, 1986

By K. J. Stratford

The selection of a suitable mathematical function for the modelling of the partition curve for dense medium cyclones is discussed. Five alternative functional forms (based on three basic functions) are compared using data obtained in the course of an extensive experimental study of a 610mm dense medium cyclone. It is shown that, for adequately sampled tests, any of the functions may be used, although a function based on the Weibull distribution is shown to be most suitable. Where data are poor, all functional forms exhibit disadvantages, notably in terms of a reduction in precision of parameter estimation. This problem can be exacerbated by the complex numerical techniques required to estimate the parameters of a particular function. A set of ideal requirements for a performance function are presented.

Jan 1, 1986

By G. A. Kosick, L. Kuehn

The design of an information management system (IMS) for a mineral processing plant requires prior consideration of many factors, which can be broadly categorized into two domains, process plant considerations and IMS considerations. The process plant considerations include: plant characteristics, management and personnel issues, existing organizational standards and policies, and the level of existing hardware and software systems. The IMS considerations include: system functionality, system sizing and desired performance, hardware components, software components, and system support issues. All of these aspects must be addressed in order to achieve a functionally successful and cost effective system. The purpose of this paper is to lay out these design issues and, in doing so, to provide process engineers with a guideline with which to tailor a system that is best suited to their specific application. The paper is completed by presenting an approach that has been used in two Canadian concentrators. Both of these plants have incorporated MillEX, a software system designed specifically as the central component of a mineral processing IMS.

Jan 1, 1993

By G. Falalakis

The Perama Hill gold project is an environmentally friendly project designed with the principle of zero discharge to the environment. The main issues of the proposed mine that are addressed in this paper are the water management, the dam and tailings management facility parameters as well as the mine closure plan, which demonstrate the sustainable design of the project. The water plant circuit will operate using 87% of recycled water and rainfalls, while the pumped aquifer is completely unsuitable for any other use. The proposed water management plan is based on different meteorological conditions for every month and optimizes the external water needs. The tailings pond area that is sited on intensely argilized rocks, will be composite-lined resulting in a permeability value of less than 10-10 m/s, and will exceed the safety parameters for maximum earthquake intensity, flood conditions and seepage. Tailings will contain less than 1 ppm cyanides (almost potable water ranges) and will be free of heavy metals (oxide ore material). The proposed rehabilitation plan comprises of decommissioning and demolition of the plant and auxiliary facilities, open pit partial back-filling and recontouring, appropriate capping of the tailings impoundment, revegetation, maintenance of area drainage system and monitoring for 5 years after rehabilitation. The plan is fullycosted, will be prepaid and through the agreed final land uses with the local community and the proposed actions of the corporate responsibility will attribute to the sustainable development of the area. The design of the Perama Hill project according to new EU and UN legislation and practices ensures that it will be the best example of gold mining operations in Greece.

Jan 1, 2008

By H. J. H. Pieterse

This paper highlights the mineralogy of the Barrick Goldstrike Mines Inc. area. The mine is located at the north end of the Tuscarora Spur and is part of the Bluestar/Goldstrike subdistrict of the Carlin Trend. The Betze, Post, and Meikle Mine are major deposits located in the area. The deportment of gold, its leachability, and various process options are also evaluated. Particular emphasis is given to the practical and economic considerations of ore control, and routing of ore to a process option.

Jan 1, 1993

By X. Yin

Surface force measurements based on atomic force microscopy (AFM) are used to describe the wettability of surfaces, specifically kaolinite basal plane surfaces at a high resolution. The kaolinite particles (~500 nm) were ordered with either the silica tetrahedral face exposed or the alumina octahedral face exposed, and surface force measurements were made between a hydrophobic diamond-like-carbon (DLC) tip and the kaolinite faces at pH 4, which is around the isoelectric point of the DLC tip. Under these conditions, the effect of electrostatic interaction should be eliminated and only van der Waals interactions and hydrophobic-hydrophobic interactions are expected to contribute to the surface force. The wettabilities of the surfaces were determined from the magnitude of the surface force. Wettabilities of the kaolinite basal planes thus determined were compared with the corresponding wettabilities of talc and mica surfaces, which are well-known to be naturally hydrophobic, and hydrophilic surfaces, respectively. The results reveal that the silica tetrahedral face of kaolinte has a modest level of hydrophobicity, which may be due to the lack of hydrogen bonding sites. In contrast, the alumina octahedral face showed no hydrophobicity, since a layer of surface hydroxyl groups is present at the alumina face, resulting in a relatively strong interaction between this surface and water molecules. It is expected that, with a better understanding of the surface properties of kaolinite, further improvements in flotation separations and dewatering may be achieved.

Feb 1, 2012

By Yu. A. Polozov, V. A. Lagunov, O. Yu. Lushinkova, Yu. I. Svirskiy, Eh. Ya. Kipko, Roy A. Williams

4.1 THE GENERAL COMPOSITION AND PROPERTIES OF CLAY-BASED GROUTS Clay-based grouts are visco-plastic systems; they are made by adding structure-forming reagents to a clay mineral mortar. Small amounts of cement and various chemical ad¬ditives constitute the reagents. If necessary, fillers also are added. The distinguishing feature of clay-based grouts is that throughout their entire stabilization period they do not form a crystallized structure as does cement grout. The structure of stabilized clay-based grouts does not deteriorate during minor rock movement or upon the initiation of blast¬ing during the construction of a shaft or a drift. Because they can possess good rheological properties during the ini¬tial structure-forming period relative to cement grouts, clay¬based grouts are not easily eroded from large fractures and karstic cavities by flowing ground water. In addition, their finely dispersed clay particles facilitate a greater fracture penetration capacity, especially in dual porosity rocks. Numerous investigations of the structural-mechanical and rheological properties of clay-based grouts by STG have demonstrated that the most effective grouts for pre¬venting the inflow of ground water into underground work¬ings are grouts that have a cement content of 8 to 10% (90 to 120 kg/m3) of the clay grout by mass. The grout should have a density of 1.18 to 1.30 T/m3. Various additional substances and chemicals can be added as additional fillers and structure-forming reagents. In pure ground water at temperatures above freezing, sodium silicate in the amount of 0.8 to 1 % by mass normally is the only structure-forming reagent that is necessary if the proper clay is selected and if it is available. The production process for making clay-based grout is divided into two stages: 1) the production of an initial clay mortar with specified properties and 2) the production of a clay-cement additive grout mixture using the initial grout along with the structure-forming reagents, including the ce¬ment. The properties of clay-based grouts depend on the phys¬ical-mechanical properties of the initial clay mineral, the properties of the cement and the properties of the chemical reagents that are added. 4.1.1 TECHNOLOGICAL PROPERTIES OF CLAY-BASED GROUTS The dynamic shear stress' To, the viscosity 11, the static shear stress2 0, the maximum shear stress of the structured that the rheological and structural-mechanical prop¬erties of clay-based grouts must fall within the following limits: the dynamic shear stress To = 50 to 200 Pa; the viscosity -9 = 0.02 to 0.07 Pa sec; the static shear stress 0 = 150 to 600 Pa; the plasticity strength Pm of the structure one minute after preparation (according to P.A. Rebinder's method) equals 150 to 500 Pa. The plasticity strength 10 days after preparation is ? 0.15 MPa. The general relationship of the change in the structural strength of clay-based grouts relative to stabilization time is shown in Fig. 32. The figure shows that the structure-form¬ing process for clay-based grouts is characterized by three stages. These stages correspond to the time periods required for conducting the principal operations during the injection of the grout into a fractured aquifer as described below. Stage I, corresponding to the time period T1, reflects the small development of structural strength during early stabi¬lization. During this time, the structural strength must not preclude the capability to pump the grout. The time Tl must correspond to the length of pumping time from the moment water is shut off and mixing occurs until the pump stops forcing the grout through the manifold block and pipeline into the fractured rock as described subsequently herein. Stage II, corresponding to the time interval T2, reflects a sharp but controllable increase in the structural strength of the grout. The length of time period T2 is controlled by the addition of appropriate reagents. Stage III produces the final value of the structural strength. This final strength is used to design the dimensions of the isolation curtain. Consequently, the development of grouts is guided by two principal criteria: 1) the grout must develop the highest possible structural-mechanical properties and 2) it must be able to be pumped by a piston pump prior to final stabili¬zation. Successful grouting depends to a large extent on the correct design of a grout for each specific case. It is impor-

Jan 1, 1993

By Jr. Bacon

Kaolin clay is one of the yeoman minerals. It sees duty in almost every aspect of our lives: -in and on most paper products (from modern newsprint to National Geographic and packaging board) sometimes as much as 25% (by weight) of the product -40% of the tile (ceramic, rubber, and linoleum) you walk on. -15 % of the tires you ride on, -30% of the fiberglass filaments in circuit boards, bathtubs, boats, doors, and more, -25% of many housepaints, adhesives, grouts, caulks, and putty -30% of sparkplugs, power insulators, dinnerware. and toilets, -50% of most catalysts (both cracking and emission control) -20% of cosmetic powders. -20% of wire insulation, and animal feed to rocket insulation!

Jan 1, 1993

By G. L. Hohmann

The Waste Isolation Pilot Plant (WIPP) project is authorized by legislation to provide a demonstration of the safe disposal of radio- active wastes generated by the national defense programs and activities of the United States. The U.S. Department of Energy (DOE) is proceeding with the implementation of the WIPP project in accordance with the "Department of Energy National Security and Military Application of Nuclear Energy Authorization Act of 1980" (PL 95-164).

Jan 1, 1982

By Robert Bissonette, Samir Sbai

Machine Situational Awareness (MSA) requires the ability to efficiently evaluate the probability of interaction of objects within the environment, without creating false alarms or ignoring materializing hazards. To do this, an MSA system needs to assign context to observed object activity and integrate as much information about object identity, kinematics, behavior, and current state as possible. This paper describes how known object characteristics, attributes, and activities (drilling, dumping, driving, etc.) can refine interaction probabilities and help identify rogue actors that introduce anomalous risks to the health and safety of miners. Path projections need to incorporate velocity and direction as a function of time while accounting for terrain, safety response, environmental factors, current assigned activity, etc. This paper also describes the methodology for properly prioritizing responses to place the highest value on human safety.

Feb 1, 2024

By T. L. Myron

In recent years increasing attention has been given to improving both the chemical and physical properties of sinter. The first step toward this goal was the production of a self-fluxing-sinter. More recently, blast-furnace operators have found that significant improvements in blast-furnace performance can be achieved by improving and controlling the physical size of the sinter. The results of full-scale blast-furnace tests have shown that blast-furnace production can be improved by using a closely sized agglomerate. The improvements obtained by the use of pellets, a closely sized agglomerate, are well known. In contrast, blast furnaces charged with sinter having a wide size spectrum have generally not yielded results as satisfactory as those from furnaces 1) * charged with pellets. Beginning in 1958, Appleby-Frodingham charged plus 3/8-inch sinter to their blast furnaces. Further tests by other companies in Canada, 2) the United States, 3) and Australia showed that blast-furnace production could be improved by about one percent when the plus 3/8-inch material in the burden was increased by one percent. Because of the promising results obtained with screened sinter, an extensive test program was initiated to determine an effective means of producing sized sinter in U. S. Steel's sinter plants. This paper describes the work done by the Applied Research Laboratory in this program.

Jan 1, 1965

By F. Calizaya, S. Bhattacharyya

"INTRODUCTION Mechanized underground mines often suffer from noise overexposure. Noise levels are usually above the Permissible Exposure Limit (PEL) where underground fans are used. Sound levels in active workings can reach 121 dB(A), especially when fans are not equipped with silencers. Use of silencers seldom ensure PEL for various reasons. Overexposure of noise induces permanent hearing loss among mine workers. Recent field studies by a NIOSH-funded research project at six coal and non-coal mines revalidated the findings. The University of Utah has undertaken laboratory studies to reduce fan noise at the source. A new silencer prototype with varying noise dampening material has been designed and tested. The silencer and an associated extension which can be repacked with different dampening materials were used in various configurations. Attempts were made to simulate field conditions where installations are quick and not perfect. The test results are presented here. NOISE IN UNDERGROUND MINES Noise induced hearing loss (NIHL) is a chronic problem in the mining industry. In spite of regulations being in place and elaborate hearing protection programs under way, hearing loss is prevalent among the mine workers (Bise, 2001). All production and support machinery in mining generate loud noise often beyond the approved exposure level. Researchers in the U.S. have identified auxiliary fans as one of the major sources of noise that can create noise exposure levels up to 121 dB(A), which is one of the highest in the mining operation (Bauer, 2006). Studies have demonstrated substantial reduction of noise level by using silencers. Adequate fan selection and proper utilization of silencers in auxiliary fans have great potential of abating the problem. In hard rock mines, auxiliary fans are used in blower configuration to ventilate development headings and large production stopes, and also to ventilate underground shops, crushers, conveyor transfer points, etc. Typical duct diameters in hard rock mines vary from 0.91 m to 1.21 m. Silencers are often omitted for cost reduction. In coal mines auxiliary fans are used in exhaust configuration with rigid ducts 0.61- 0.76 m in diameter (Hagood, 1982 and Moreby, 2009) to ventilate working faces in gate-roads and main entry developments. Sometimes, stone dusters are added at the discharge end to dust the roof, ribs and floor. AUXILIARY FANS AND SILENCERS Auxiliary fans are relatively smaller in size than the main fans and often have high rotational speeds (1800 -3000 rpm). Fans are selected based on pressure-quantity requirements and space restrictions only. Noise emissions are rarely considered during the selection stage. Installation of fans, ducts and other accessories is mainly based on best practices, which often do not include noise control. As a result, the operation of an auxiliary or local ventilation system normally produces excessive noise."

Jan 1, 2018

By C. W. Benjamin

The paper covers the development of an efficient, "state-of-the-art" design approach encapsulating extensive research and development by Gulf on soft loading, low impact, zero spillage transfer chutes. The development, which interacts and interfaces the comprehensive methodologies for transfer chute design, allows Gulf to deliver detailed designs within 8-24 hours rather than the norm which is weeks or months. Outputs include 3D models of completed transfers and support structures along with rendered 3D representations of the design which can be fully manipulated around all axis in 3D.

Jan 1, 2000

By Kenneth N. Han, Yichang Guan

The dissolution behavior of metals from Au/Ag/Cu-alloys has been studied using rotating disc electrodes in solutions containing acids, cyanide, and ammonia. Electrochemical methods as well as leaching tests were adopted in this study. The results showed that there was no galvanic effect on the dissolution of metals from homogeneous alloys. In aerated cyanide solutions, the dissolution of gold, silver, and copper from their alloys was partly controlled by surface chemical reaction, but largely by mass transfer. On the other hand, the galvanic coupling effect played a very important role in heterogeneous alloy systems.

Jan 1, 1995

By R. L. Miller

Two samples of iron enriched basalt (IEB) containing simulated nuclear fuel and having two distinct microstructures were prepared and tested for uranium recovery. The IEBs are refractory towards leaching by ground water. However, the uranium content (15.8%) is high enough that if aggressive leaching techniques are used for uranium recovery, these materials could be considered as man-made uranium ores. The IEBs discussed in this report were prepared to simulate Three Mile Island-2 core debris. The crushed IEBs were treated using three different methods simulating potential industrial scale processes. In one method the IEBs were fused with sodium hydroxide then the cooled mass leached first with water then with dilute sulfuric acid; about 52% of the uranium was recovered in this case. In the second method the IEBs were treated with a sulfuric acid/hydrogen peroxide lixiviant and about 13% of the uranium was recovered. In the third technique the IEBs were leached with a sodium carbonate/sodium bicarbonate/hydrogen peroxide solution. Only about 0.1% of the uranium was recovered. The results of these screening tests suggest that the IEBs can be successfully treated for recovery of the contained uranium. Other studies would be required to determine if other values, such as zirconium or silver, could be recovered from the IEBs.

Jan 1, 1984

By Ali Hafiz, Aidin Golrokh, Tom Iseley, Kaz Tabrizi, Saleh Behbahani

In the USA many highway tunnels were built during the 1930s through 1960s. This indicates that these tunnels have exceeded their intended design service life. Based on the initial tunnel inventory conducted jointly by the Federal Highway Administration (FHWA) and the Federal Transit Administration (FTA), more than 526 highway tunnels have been identified in the USA. For understanding the condition of the tunnels and risks associated with deteriorating conditions, comprehensive condition assessments are necessary to mitigate risk and remediate works as required. Monitoring the condition and rate of deterioration of tunnels is vital for timely tunnel maintenance and rehabilitation to avoid sudden tunnel collapse. This session will explain the necessary steps for tunnel inspection and review some of the state of the practice information on tunnel inspection techniques.

Jun 13, 2023

By R. M. Wheeler

For years the blasting industry has recognized eight milliseconds as the minimum delay time interval required between charges in order for them to be considered to fire independently of each other. However, computer analyses of seismic recordings made of several surface mine blasts reveals that this time interval may not always be sufficient for adequate vibration separation to occur. In some situations a combination of short delay periods and low frequency vibrations can result in waveform reinforcement. Various analyses of seismic recordings obtained from single hole detonations can be used to predict delay intervals that may enhance or reduce blast vibration effects.

Jan 1, 1987