Search Documents

By L. Adler

A systematic, balanced and inclusive formulation of the vast input data for mine design is presented. Since the quality of this statement severely influences subsquent design it is extremely important to senior mining engineers and the profession-at-large. If unfocussed, chaos can result along with serious ommisions. The basic categories, each a traditional one are: 1) Natural Conditions (geology and geography), 2) Company Capabilities (monetary and managerial), 3) Public Domain (regulations, contracts, good will, etc.) and 4) State of Art (mining engineering professionalism). To further reduce the data additional organizing principles were used: the distinctions of mining (vs. civil) engineering, proceeding from the general to particular, the basic engineering dimensions, and separating dependent from independent variables. The results are a unique and unified corpus, which anticipates the mine design procedure.

Jan 1, 1987

By William M. Phillips

This paper will concern the processing of kaolin clays from the sedimentary deposits of Georgia and South Carolina, While the major processing steps will be touched on briefly, emphasis will be given to the dewatering of the clay-water slurries (slips) formed in the processing of kaolin clays The dewatering steps discussed will include gravity settling, centrifugal dewatering, vacuum filtration, and thermal dryings Of these dewatering steps particular attention will be given to vacuum filtration and the variables affecting filtration of these kaolin clays.

Jan 1, 1962

By B. K. Parekh

Silicon carbide (SiC) can be produced by heating rice hulls to elevated temperature, The product is a mixture of beta crystalline silicon carbide whiskers, particles and unreacted carbon. The silicon carbide whiskers are 0.5 micron in diameter and 50 to 100 micron in length and have been found useful for reinforcing metal and other composite materials. The carbon can be removed by combustion, but this makes separation of the silicon carbide whiskers from particles difficult and a high grade whisker product cannot be made. However, a clean high grade Sic whiskers product can be obtained from the pre-burned converted rice hulls using physical separation processes that are based on differential wetting. Recovery of Sic whiskers from the pre-burned material was found to exceed 90 percent. A modification of the froth flotation process developed during this study is now being used commercially to separate silicon carbide whiskers and particles and to recover a high grade whisker product.

Jan 1, 1985

By Silvia Misk, Cristina Araújo, João Felipe Costa, Roberto Rolo

Linear estimation methods are widely used for resource evaluation. Among the existing linear estimation methods, ordinary Kriging (OK) was accepted as the best estimator to determine the average ore grade of each block. However, OK is inadequate for modeling small blocks in relation to data spacing, resulting in over-smoothed models. In this study, the results of the recoverable resource from the short-term model are compared to estimated models generated by the traditional method, i.e., OK, and non-linear methods. The conclusion is that non-linear methods improve the accuracy and precision of the long-term model when compared to the model generated by OK.

Jun 25, 2023

By K. F. Unrug

The concept of bolting mine roofs to prevent roof falls was initiated in the 1950's and was quickly accepted by the mining industry because it was inexpensive, effective and convenient. The principle regarding roof bolting were that: a) the loose and fragmented rocks were suspended from or clamped to more competent surrounding rock and b) generally, by clamping several layers of thin and laminated strata, a more competent monolithic beam is created.

Jan 1, 1991

By Randall E. Brown

Irrigation simulates a climate change so that crops can be grown that otherwise would not thrive. The abundant sunshine and warm weather of many arid regions induces a rate of growth in excess of that in cooler, moister regions. Hence, the arid part of eastern Washington, traversed by the Columbia River, is admirably suited to irrigation. The Pasco Basin lies in south-central Washington at the south end of the Columbia Basin Irrigation Project of the U.S. Bureau of Reclamation. The Basin, because it lies in the rain shadow of the Cascade Mountains, receives only 6 to 10 inches of precipitation a year with somewhat greater amounts, commonly as snow, on the higher hills. Recent extremes included 3 inches of precipitation from August 1967 to August 1968, and 12 inches in the succeeding "12 months. Most of the precipitation falls during winter. If it were to fall in summer or were evenly distributed throughout the year, evaporation rates probably would produce a true desert.

Jan 1, 1971

By Richard V. Wyman

The genesis of ore deposits has been tied to plate tectonics through differential petrogenesis in subduction zones. However, many mineral districts, especially in the Basin and Range province of United States and Mexico, appear unrelated to any possible subduction zones or to plate boundaries. It is proposed that the pattern of mineral belts is related to mantle plumes which have been overridden by an advancing continental margin.

Jan 1, 1976

By Richmond Bennett

Airborne geochemistry became a reality with the advent of a high-sensitivity airborne gamma ray spectrometer with large volume NaI (TI) crystal detectors. Small variations in the concentration of potassium (as K40), thorium (as T1208) and uranium (as B1214) along the flight lines can be determined by measuring the gamma radiation with a sensitive airborne spectrometer. Small volume crystal spectrometers are useful only for detection of major surface uranium (Bi214) variations, but the large crystal volume system is an airborne geochemical exploration method capable of locating hydrothermal mineral deposits. Radioactivity as a guide to ore has been discussed in the literature by Damon (1950), Gross (1952) and others. The theoretical basis is that potassium, thorium, and uranium are concentrated in late stage solutions during magmatic crystallization. Thorium and uranium are concentrated in late stage liquids because their large atomic radius and high ionic charge prevent them from entering into the crystal lattice of common rock-forming minerals (Rankama and Sahama, 1950). Potassium, which has a large ionic radius and small charge, also can be concentrated in the high water content late stage fluids (Heier and Adams, 1964). A large proportion of uranium and thorium in rocks occurs around grain boundaries of the essential rock-forming minerals (Hurley, 1950). Uranium and thorium substitute for zirconium in zircon, a comparatively early forming mineral. However, most of the thorium and uranium is concentrated in residuals where they can be fractionated and incorporated into allanite, monazite, xenotime, and other minerals.

Jan 1, 1970

By A. T. Yu

Technology and economies of scale have, in the past decade, brought about the emergence of giant vessels. Meanwhile, to answer the need for rapid dispatch, as a means of combating the proportionately far greater demurrage charges, shiploading and unloading speeds have soared (Ref. 1, 2, 3). As the loading and unloading rates have dramatically increased, so has the cloud of dust grown in unbearable proportions. It not only has threatened to be a real menace to machinery and men, but in certain instances has also seriously jeopardized fish and marine life (Ref. 4). In an era when ecology is king, dust in shiploading and unloading can no longer be shrugged off as a mere public nuisance, and its control is now duly recognized as of grave concern to all. Even if public outcry were not a problem, from the operator's own parochial point of view, dust can adversely affect productivity and the well-being of the operating personnel. Without adequate control, it can also result in costly equipment maintenance, particularly when the dust is micronic in size, and abrasive. The Hierarchy of Control Techniques Given the great fortune of not yet having to deal with gas and odors, in the jargon of pollution control, our problem is confined to having to control "particulates" only. To deal with "particulates", the myriad of dust control techniques can be utterly confusing to those who are not entirely well versed in the methodology. Our analysis of what is available to date results in the following hierarchy of logical preferences: 1. Prevention 2. Removal 3. Suppression 4. Containment 5. Dilution Since it deals with the root cause, prevention always outranks the cure. Once the dust is generated, removal nips it in the bud. Only when dust removal is

Jan 1, 1972

By Meredith Scaggs, Emily Sarver, Lucas Rojas Mendoza

"Early on Jan. 9, 2014, approximately 37,800 L (10,000 gal) of crude 4-methylcyclohexanemethanol (MCHM) leaked from a storage tank sitting on the bank of the Elk River near Charleston, WV (WVDEP, 2014; CSB, 2014). MCHM is a chemical commonly used in preparation of fine coal and is considered nonhazardous in terms of transportation, storage regulations and also toxicity (CDC, 2014a). Freedom Industries Inc., a producer and vendor of specialty chemical products, had acquired the storage facility from Etowah River Terminal, LLC just a few weeks prior in December 2013 (WVDEP, 2014; Freedom, 2005). The direct cause of the spill was ultimately determined to be two small holes in the base of the 76-year-old tank, which were created due to corrosion damage (Bauerlein and McWhirter, 2014).The spill site was located a little more than 1.6 km (1 mile) upstream from the intake of a municipal water treatment facility operated by West Virginia American Water (WVAW), which serves a population of 300,000 across nine counties in central West Virginia (CDC, 2014a). In a matter of hours, the leaked MCHM made its way through the treatment facility and into the water of nearby homes and businesses, where its strong smell was noticed almost immediately. On the evening of the spill, WVAW concluded that its conventional treatment processes, which include carbon filters to remove a variety of contaminants from water, were not capable of fully removing the MCHM and a "Do Not Use" order was issued for all customers (WVAW, 2014a).With little information readily available regarding the potential human health effects of MCHM, the U.S. Centers for Disease Control and Prevention (CDC) quickly issued an advisory ruling that set a maximum screening level of 1 ppm for safe drinking water (CDC, 2014a). Based on this recommendation, the "Do Not Use" order remained in effect for a total of eight days, until Jan. 17, when the WVAW distribution water was confirmed to have MCHM concentrations below the approved level (WVAW, 2014a). However, due to the pungent odor of the chemical, its presence was still recognizable in the WVAW facility and in consumers’ tap water after the order was lifted (Manuel, 2014). Recent studies have shown that the chemical can be detected in water at sub-ppb concentrations, a fact that undoubtedly added to growing public concern (Rosen et al., 2014; Gallagher et al., 2014). In response to numerous complaints and demands, WVAW continued flushing the treatment facility and pipes until Feb. 25 when MCHM levels were measured below 2 ppb (WVAW, 2014b), and eventually replaced the affected filter media (WVAW, 2014c)."

Jan 1, 2014

By A. H. Brisse

In considering the use of a coal or a coal blend for the production of metallurgical coke, the fact is often overlooked that laboratory data can be most effectively used to determine coke plant operating conditions conducive to maximum output as well as to predict the quality of coke produced. The discussion here presented attempts to point out the manner in which carbonization data can be interpreted for industrial use and the significance of specific laboratory test results in this interpretation. The major considerable must, of course, be the safeguarded of coke oven batteries, against wall damage arising either from excessive carbonization pressures or from the wedging of the pushing ram into non-contracting coke charges. In order to be specific in the matter of handling the laboratory data involved, two series of blends are analyzed. The first of these, referred to as the "AB" series, is typical of some d' the more highly expanding Eastern- coal blends whereas the second series, here referred to as the "CD" series, is probably more typical of the Western coal blonds. Reference to Table II should be made for rank of coals considered in these blends.

Jan 1, 1959

By Robert C. Sutter

In 1958, it became obvious to some of us in the solution mining business that there were certain problems in connection with our sodium chloride brining operations which were industry- wide. These were the types of problems which, while they were important to the safe and economical operation of our salt brining operations, were not such that their solutions would give an individual company a great competitive advantage over his competitor; and since they involve the safe and efficient mining of a natural resource, it was obvious that the answers would, in any event, be shared industry-wide. Since we were dealing with underground solution mining and, consequently, unseen and remotely controlled operations, the problems are formidable and the solutions difficult. While all of us were doing work to improve our operations, none of us could justify the expenditures necessary for basic research in these areas. Consequently, the idea was conceived of research sponsored by many companies with the same problems. In 1960, 11 companies entered into a' formal agreement to jointly support research on a specific problem of sodium chloride solution mining. The project to be undertaken was the development of a method for measuring the size and extent of underground solution cavities in sedimentary salt beds. It was agreed that all research was to be performed by independent research organizations. A part-time consultant or administrator was retained to administer the research contracts and to provide technical advice.

Jan 1, 1966

By Arthur A. Schweizer

A method to improve the quality of Magmnt zinc concentrates to become acceptable feed to an electrolytic zinc refinery. The magnesia content of zinc concentrates produced was too high due to particle locking with the sphalerite in coarse fractions. Regrinding of the concentrates to a very fine particle size and then refloating the sphalerite was chosen to eliminate a sufficient amount of the magnesia to make the concentrates acceptable.

Jan 1, 1981

By Thad J. Bydlon

Uncertainty of future energy supplies has forced industrial nations to diversify both their energy mix and their energy sources of supply. As a result, U.S. coal exports have grown substantially during the past several years. Projected long-term worldwide economic growth suggests that a well-established trend has been set for increased foreign demand for U.S. coal. As export volumes increase the need for careful planning to prevent bottlenecks and to provide for the uninterrupted flow of coal increases. It also will place increased emphasis on identifying the most economic transportation alternatives. These planning and evaluation functions are greatly facilitated if a systematic method is available for modeling the complex interactions of a coal export system. One such model, developed by the Anaconda Minerals Company, is the Coal Export model.

Jan 1, 1982

By Hongjie Yu, Mike Mooney

Transitions between geological/geotechnical soil units have a critical impact on the operation and performance of a tunnel boring machine (TBM). Geostatistics-based probabilistic modeling is used to quantify the uncertainty in soil transition locations. This paper presents two unique soft-ground tunneling case studies where the results from the geostatistics-based probabilistic modeling are compared to the TBM data and as-encountered ground conditions derived from the actual TBM data. The assessment enhances the confidence in using geostatistics to improve ground awareness for efficient tunnel construction, minimizing different site condition (DSC) claims, and improving decision-making on tunnel projects.

Dec 1, 2022

By J. A. L. Campbell

Peabody's Camoy mining system is a truly continuous conceptual method of underground mining of coal. The system solves the three factors which limit coal from being mined continuously. Camoy's principal features are improved productivity and increased recovery. A conservative retreat production rate of 2 1/2 times normal continuous miner room-and-pillar mining rates are projected for a 6-7' seam. Overall mine productivity will be 2 times normal, with a potential for considerably higher rates. Major incremental production increases can be achieved by partial implementation of the system. Total mine recoveries of 75% are expected. The system includes both advance and retreat mining. The retreat half of the approach encompasses many of the features of short wall mining. A central panel is prepared for retreat mining by driving entries using room-and-pillar mining to the left and right of it. The room-and-pillar mining encompasses the advance features of Camoy. In the retreat phase, the roof of the face is supported by self advancing chocks or shields. All mining is done under the chocks by a continuous miner. As the miner advances the chocks continuously move forward behind it. Thus, as in a typical short wall system, continuous roof support is attained. Ventilation is unidirectional, another characteristic of short-wall type systems. Fresh air is brought in and passed over the working personnel. It moves to the face where the continuous miner is operating, picks up the generated dust and released methane, and is exhausted away from all personnel. Exposure to respirable dust and ignition hazards due to methane build-ups are almost totally eliminated. Thus, the second limiting factor is overcome and continuous ventilation is attained. Coal mined with the continuous miner is passed to a surge car and then to a Serpentix conveyor. The Serpentix, a Peabody invention, is a flexible conveyor capable of going around corners.

Jan 1, 1976

By Larry Diaz

A single stage ball mill-cyclone circuit was extensively tested for its reactions to step changes in three controllable variables: feed rate, water to cyclones, and water to the ball mill. A series of carefully designed tests are to be carried out in order to determine relationships between the various ball mill and cyclone parameters. Cyclone overflow particle size distribution is to be continuously monitored during the tests using an ultrasonic device. Other circuit variables that are to be measured and recorded are feed rate, ball mill mass flow, cyclone feed and overflow densities, cyclone feed sump level, water flows, etc. Once the circuit performance is defined, two types of grinding circuit control systems will be evaluated: (a) mass flow-based; (b) particle size- based. Results obtained by each approach in terms of feed rate and cyclone overflow size distributions are discussed. The high sensitivity of continuous particle size measurements to grinding circuit disturbances is emphasized.

Jan 1, 1971

By C. M. Bartley

In world-wide mining circles countries become known by the principal minerals they produce. The production of iron, copper, phosphate and sulphur in the United-States-has-been particularly significant and has provided the base for aggressive developments in heavy industry, agriculture and chemicals. Mention diamonds and gold-and you will think--South Africa; silver-Mexico; nickel and asbestos--Canada. The main purpose of this paper is to point out that potash mast be added to the list of minerals by which Canada is known in the mining World. The potash deposits of western Canada must be classed as a major world source of chemical fertilizer raw material. We believe that they are both the largest and the richest of all known deposits in the world. The most knowledgeable people in the industry avoid making estimates of reserves because even where the arithmetic is correct the total is so large that it appears to be ridiculous. In 1957 Marion Goudie made a carefully qualified estimate of 6 billion tons of recoverable potash above 3,500 ft, and grading 25 per cent K20 or better. This figure can now be increased by the amounts available through solution mining. No one has bothered to estimate how much this is because it is so large that the actual amount is not significant.

Jan 1, 1966

By E. J. Onuscheck

With passage of the Federal coal' Mine Health and Safety Act of 1969, many challenges have been directed to the industry's mining and safety engineers. The most critical challenge is that of ventilation. The language concerning ventilation in many sections of the Act could very well deprive or limit the mining engineer in planning the ventilation for new mines, since the Act requires federal approval of all ventilation plans. Dependent upon approval and of course application of the law, this could, due to economics, prohibit the opening of new mines in some cases. Petitions for modification of some mandatory standards relating to ventilation have already been filed under Section 301(c). It is quite possible that many of these standards may be modified.

Jan 1, 1970

By Alessandro Navarra, Aldo Quelopana

Sophisticated models have progressively been developed to address the challenges related to long-term, openpit mine planning under conditions of geological uncertainty. Prior research has acknowledged that strategies for mine planning and the design of mineral concentrators are interdependent; thus, it is highly desirable to optimize them together. However, achieving detailed holistic optimization of the mineral value chain remains unresolved because of the inherent limitations associated with mathematical formulations and computational processing capacity. This paper details a method that contributes to bridging these limitations by employing a novel parallelized variable neighborhood descent approach combined with an embedded mass–balance component using linear programming techniques refined through Dantzig– Wolfe decomposition. This approach is exemplified through a case study of a gold deposit, which illustrates the enhanced performance capabilities of the new algorithm. The findings demonstrate significant improvements in the optimization process for mine planning, providing a stronger link between the mine’s output and processing plant’s capabilities.

Mar 1, 2025