Search Documents

By R. J. Lee

Asbestos analysis is conceptually simple. The objective, in most environmental analyses, is to determine the number of asbestos fibers per unit area or volume in a sample. The sample may be a consumer product, an ambient air sample, or a water sample. This determination is complicated by several factors: (1) sample collection and preparation, (2) counting techniques, and (3) operational definitions of asbestos in use. Three different definitions have been used in the study of environmental samples and are summarized in Table 1. The analytical procedure and detail required in the analysis vary with the definition of asbestos. Accordingly, this may be the only type of environmental analysis where the definition of a substance dictates the choice of analytical methods, and the rigor demanded of the analysis. Lead, arsenic, or beryllium are sub- stances having a constant definition and the method of analysis chosen depends on the concentration and precision required. However, the meaning of the term asbestos fiber is dependent on the eye of the beholder. Macroscopically, asbestos has certain physical properties that make it highly useful. Rockforming minerals do not display similar characteristics. Now, the question arises as to how three definitions of asbestos came into being. This is a result of two factors: (1) the definition of asbestos on any scale intrinsically involves the morphology or shape of the material, and (2) the advent of the transmission electron microscope permits detection of asbestos fibers and other mineral fragments in a size range where the physical properties of asbestos such as tensile strength, flexibility, or thermal resistance are difficult, if not impossible, to measure. There is a good deal of controversy about which definition is most appropriate for regulatory purposes because of a lack of appropriate health effects data (Cooper, 1978). Most differences of opinion center on the questions surrounding the following: 11 Morphology-Is a 3:l aspect ratio an appropriate medical or physical lower limit for the definition of an asbestos fiber? 2) Length-Are asbestos fibers shorter than some arbitrary length (5 pm) as hazardous as longer fibers? 3) Mineralogy-Is the mineralogical distinction between asbestos and nonasbestos minerals medically significant? While these questions are directly resolvable only with the biological and health effects data, ultimately such data reflects the ability of analytical procedures to fully characterize the materials used in health effects studies on animal models, and to monitor the exposure to particulates with different physical attributes in the workplace or community (Cooper, 1978). The following sections outline the analytical problems involved in distinguishing the asbestos and nonasbestos varieties of the same mineral; the analytical procedures available for identifying asbestos and measuring its concentration in environmental samples; the ability of these methods to distinguish asbestos fibers from nonasbestos particles; and their precision and reproducibility. Finally, we suggest some future directions in terms of definition and procedure that would greatly improve the quality of such analyses. ASBESTOS VS. NONASBESTOS Asbestos that is mined commercially belongs to two mineral families; amphibole and serpentine (Zoltai, 1978, Wylie, and Steel, 1978). The

Jan 1, 1986

By D. Kimball, P. Chambers

"BACKGROUND In the event of an explosion or fire in an underground mine, workers can be exposed to a deficiency of oxygen, an excess of carbon monoxide, or both. These threats can occur as separate conditions or simultaneously. A lack of oxygen in the breathing air can only be addressed via the use of a self-contained breathing apparatus (SCBA) acting as a source of oxygen. An excess of carbon monoxide can also be addressed via the use of an SCBA, but if the threat occurs in isolation (that is, the atmosphere still contains sufficient oxygen to support life) and the concentration of the threat gas is not extreme (< 2%) then the carbon monoxide threat can also be addressed by the use of a filter self-rescuer (FSR). Used together, the SCBA and FSR offer a far more efficient and universally capable life support system than when used in isolation. However, the SCBA does not take advantage of the fact that the surrounding atmosphere likely contains some level of useable oxygen; i.e., the SCBA always supplies the total required oxygen from its limited supply, resulting in a ceiling on its useful life regardless of the level of oxygen in the surrounding air. To address this technology gap, what is needed is a ""smart"" SCBA that provides filtration and catalytic protection against threat gasses and has an extended duration life-sustaining oxygen inhale stream independent of the threat content and oxygen deficiency of the surrounding atmosphere. DEVELOPMENT Developed under contract with NIOSH the Smart Escape SCBA is comprised of three major components including; 1) oxygen supply, 2) oxygen sensing & dosing electronics and, 3) a CO catalyst and carbon bed broad spectrum FSR. The SCBA is designed as a hybrid system that provides non-toxic breathing air by using an approved Chemical, Biological, Radiological and Nuclear filter self-rescuer and a catalyst to convert high levels of carbon monoxide to harmless carbon dioxide (CBRN FSR/CO). In addition, the Oxygen Sensing & Dosing Electronics (OSDE) package adds sufficient oxygen to make up for deficiencies detected in the ambient air (Figure 1). By making use of the ambient oxygen, less oxygen is required for a one-hour unit life. This means that the Smart Escape SCBA fits in a smaller and lighter package than a similar-duration conventional Self-Contained Self-Rescuers (SCSR). Alternatively, taking advantage of available ambient oxygen could offer a significant increase in working duration in a unit with the same size as current SCSRs. The research performed under this NIOSH contract involved numerous tasks including: (1) definition of performance and system requirements for the Smart Escape SCBA, including keeping environmental stressors within acceptable ranges, providing at least one hour of breathable oxygen supply, and using a mask or hood that allows high-quality voice communication; (2) designing, building, and evaluating prototype units to support extensive bench top testing at Avon Protection and third party labs to demonstrate the device’s capabilities; (3) building sufficient quantity of Smart Escape SCBAs designed to be intrinsically safe (per MSHA criteria); (4) testing and evaluation by the National Personal Protective Technology Laboratory (NPPTL)."

Jan 1, 2015

By Jerzy Iskra, Wlodzimierz Sikora

INTRODUCTION The effect of stress concentration in coal seams leads to a sudden release in the form of rock bursts. This effect is controlled along many lines, but the most efficient methods consist in preventing the accumulation of energy in the seam or in the roof. The over- burden weight resulting from mining is the main cause of excessive stresses in a seam. An additional weighting of roof takes place due to formation of abutment loads. The accumulation of energy in the roof takes place where thick sandstone beds occur in overburden strata. An essential problem is to watch, with appropriate measurements, the stress of coal and roof rocks, and to conclude, on this basis, the degree of rock burst hazard. The methods for determining the stresses in a coal seam are quite well developed at present. Let me mention here the seismoacoustic methods, or borehole overcoring measurement methods. On the other hand, an examination of the state of stress in the roof rocks is almost impossible at the actual stage of development of the measuring technique. Hence, the model of stresses in roof was analyzed and determined theoretically. Based on this model, a technology for roof fracturing was developed which aims at destressing rock masses in a planned way. The essentials of the fracturing method consist of a controlled breaking of sandstone roof beds in order to: - prevent the excessive weight on the pillar - prevent a spontaneous breaking of roof beds at a limiting state followed by sudden energy release. High pressure fluid infusion is used to release buildup of stresses. THEORETICAL AND RESEARCH BASES According to the tests carried out by A. Kidybinski by the method of finite elements, isobars of stresses occurring in the roof over the working face are shown in [Fig. 1]. The results indicate: - the highest values of compressive stresses occur in the roof directly over the seam, at a distance of about 5 m ahead of the working face - at a distance of about 22 m above the seam there is a line of transition of compressive stresses into tensile - within the tested roof area, the highest tensile stresses occur at a vertical distance of 35 m, and at a horizontal distance of 20 m from the line of the working face. H. Gil (1) determined the pres- sure initiating the fracture of roof rocks by the formula: [ ] On the basis of results of analysis of isobars, and of the initiation of failure stress formula (1), isobars may be designed for a given roof class. Assuming for sandstones the Poisson ratio equal 0.3, a field of failure stresses presented in [Fig. 2] is obtained. In this figure it can be seen in which areas the effects of sandstone breakage may be obtained with the operation of a determined hydraulic pressure. To use formula (I), the knowledge of Rr is still necessary. This value may be determined in two ways: - taking a sample and testing it in the laboratory, if there is access to roof rocks in the existing openings, - drilling boreholes in the roof from surface and examination of the rock mass by using hydraulic breaking, if there is no access to roof rocks.

Jan 1, 1982

By G. W. Cutting

It is well known in both the research field and in commercial flotation processes that the grades and recoveries obtained from flotation plants are heavily influenced by the structure and height of the froths produced in the flotation cells. The development of steady-state mathematical models of flotation processes based upon practical and readily obtained parameters have demanded detailed information about the structure of flotation froths. The important parameters are the distribution of floating values, gangue and water in the froth with respect to froth height, cell pulp density, cell air flow rates and flotation inducing additives. Little work has been conducted in this field although considerable attention has been paid to bubble loading and other factors close to the cell froth/pulp interface. Laboratory batch tests are prefaced for the derivation of the above mentioned parameters for both practical and economic reasons. The standard laboratory flotation tests using a batch cell produces a froth of low height (1 to 3 cms generally) together with a varying cell pulp density as the test progresses due to the addition of top up water and the removal of froth from the cell. This form of test can be considered only as giving information about froth conditions close to the cell froth/pulp interface under conditions of widely varying cell pulp densities. In commercial processes the froth heights are much larger (frequently greater than 10 cms); therefore the laboratory batch test, although useful in many ways, does not directly yield parameters relating the state of the froth flowing over the cell lip to process operating conditions. To investigate flotation conditions, where more realistic froth heights are developed, an equilibrium type of batch cell has been developed at Warren Spring 1 Laboratory . In this a tank with high walls is used to contain the pulp and whole froth and, after a short period of operation, an equilibrium between froth

Jan 1, 1975

By R. K. Zipf

Recent scientific studies by researchers at the National Institute for Occupational Safety and Health (NIOSH) and the U.S. Army Corps of Engineers (USACE) presented the worst-case explosion pressures that can develop if a methane-air mixture of a certain composition and dimension accumulates and ignites within a sealed area of a mine. The Mine Safety and Health Administration (MSHA) issued its final rule on sealing of abandoned areas which considers potential explosion pressures and the risk of achieving the necessary conditions. The new MSHA seals regulation has increased the pressure design criteria an order of magnitude beyond the old standard of 140 kPa (20 psi) to 800 kPa (120 psi). However, there still are major knowledge gaps pertaining to seals and sealed areas including: (1) the composition of the sealed area atmosphere and how it changes in time and space, (2) explosion pressures that might actually develop within sealed areas, (3) engineering procedures to follow when designing seals and seal installations, and (4) guidelines to manage the atmosphere within sealed areas with monitoring or inertization. NIOSH has initiated a seals research program with collaborators from Safety in Mines Testing and Research Station (SIMTARS) in Australia, West Virginia University (WVU), the Naval Research Laboratory (NRL), and USACE. Highlights of progress so far include: (1) construction of a gas explosion tube at Lake Lynn Laboratory for studying large methane-air explosions, (2) computer simulation of the fluid dynamics of high pressure methane-air explosions, (3) development of seal analysis methods considering construction materials, reinforcement and the seal foundation, and (4) development and testing of innovative seal designs that utilize inexpensive, readily-available rock rubble to resist high explosion pressures. NIOSH researchers aim to provide sound engineering guidelines to better address the new MSHA seal regulations. DISCLAIMER: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By William J. Douglas

Defining Productivity Productivity is a principal concern to all organizations - industrial, commercial, government, and academic. As a ratio of output to input, productivity measures the efficiency of an industrial process, much as thermodynamic efficiency measures the useful work obtained from the available energy consumed. However, there is one important difference. Whereas thermodynamic efficiency is a dimensionless a ratio of energies, productivity output and input are usually measured in different physical units. Nevertheless, the resulting ratio is a normalized expression for unit of output per unit of input to the process. In the early days of coal, mining was essentially a hand loading operation. There was little expenditure of alternative forms of energy within the process. Loading required expenditures of human energy on the order of 1.2 MJ/t (1,000 Btu per st). And if we accept the conventional value "you load 16 tons," the output to input ratio is 14.5 t (16 st) per manshift. In energy terms, it is on the order of 116 MJ/t (100,000 Btu per st) produced per labor Btu expended. However, the latter measure of efficiency was not meaningful in economic terms, while the 14.5 t (16 st) per manshift was significant. Since labor was the principal component of cost, it represented a direct relationship to the cost of production: [ ] Furthermore, when workers were paid directly on the basis of tons produced, the labor cost per ton was specified directly by this rate. With the introduction of mechanized loading, significant increases in productivity occurred, when measured on the basis of tons per manshift. Electric power consumed about 11.6-116 MJ/t (10,000-100,000 Btu per st). This makes the 29-GJ/t (25 million Btu per st) coal output/input ratio between 100 and 1,000. That is one or two orders of magnitude lower than hand loading. However, electric energy was quite inexpensive compared to labor, which made the mechanization economically efficient. The accepted productivity measure continued to be tons per manshift. This measure includes some of the effects of mechanization: namely, the additional manpower needed to maintain the machines and support the equipment that uses electrical energy. However, it does not consider the capital and operating costs that relate to mechanized equipment. As a result, the concept of tons per machine-shift has emerged as an accepted measure of shift productivity. The only appropriate measure that encorporates the productivity of men and machines is an economic one. The output is the tonnage per shift and the impact is the cost per shift. [ ] This is simply the inverse of the cost per ton. In addition, much flexibility is available in allo¬cating costs to the three categories. This adds a level of intangibility to the measure. The amount of information needed to obtain all of the required costs is appreciable compared to the simple matter of counting tons and workers. Furthermore, financial information relating to production costs is closely held by mining companies, so historical statistics on economic productivity are not publicly available. To extend the concept further, consider the value of the tonnage produced, to obtain a dimensionless ($/$) measure of economic productivity.

Jan 11, 1983

By Ian P. G. Hutchison

12.1 INTRODUCTION This chapter deals with the tools required to design leach operations to minimize spillage from leach pads and ponds and erosion damage during flood events or prolonged wet periods. It outlines methods used to design for prolonged dry periods when water shortage can be a problem. Seasonal operational aspects such as winter shutdown and coping with spring snowmelt periods are also discussed. General criteria useful when designing pregnant and barren solution ponds are also outlined. The aim of these notes is to provide designers and operators with a simp1ified approach to developing design parameters which make effective surface water management easy to achieve without resorting to extensive or elaborate analyses. Section 12.2 briefly outlines the types of problems associated with wet climates and floods, as well as dry periods. Determination of flood design parameters is discussed in Section 12.3. Circuit water balance and pond sizing are outlined in Section 12.4. Pond design considerations are included in Section 12.5. Worked examples are included in Section 12.6. 12.2 RAINFALL/RUNOFF PROCESSES There are two types of rainfall-runoff processes that are important when designing heap leach facilities. The first of- these is the short-term, intense rainfall or snowmelt events that occur over a period of a few minutes or hours, causing flooding that can lead to erosion damage and overtopping of ponds and containment dikes. Specific problems that can manifest themselves during these events include: • Washout of access roads; • Damage to containment dikes; • Flood water contamination of circuit water; • Damage to process water ponds by perimeter erosion or overtopping and erosion; • Loss of process circuit fluid due to breaks in containment dikes or process water ponds; and • Erosion of leach pile and consequent sediment contamination of process fluid. Other types of rainfall -runoff processes that could cause problems are the long-term-(generally months-long) wet or dry periods. Extended wet periods

Jan 1, 1988

By Daniel Su

This paper describes recent ground control challenges encountered at the longwall recovery areas of one of Bailey Mine?s two longwall faces and the proactive measures taken by CONSOL management and engineering to mitigate them. The challenges derived primarily from the following causes: (1) irregular roof coal and draw slate thickness, (2) presence of thick sandstone at the recovery area and extremely weak rocks below the sandstone, (3) close proximity to a regional anticline, (4) low shield set pressure and tip load, and (5) ineffective primary roof support that led to progressive failure of the headgate roof. The presence of the anticline contributed to extensive fracturing of the sandstone. Excessive pot-out in advance of the shields frequently occurred near mid-face due to the presence of thick draw slate and irregular roof coal near the recovery area. This, in turn, resulted in face heights that exceeded the maximum reach of the shields. Subsequently, during longwall meshing, when the advance rate slowed considerably, fractured sandstone would often break loose, causing the shields to yield, thereby reducing the height and inhibiting shearer movement. To improve the headgate and face conditions within the longwall recovery area, several actions were taken, including: (1) assessing site-specific roof geology by conducting in-mine roof coring around the recovery areas and by mapping immediate draw slate and roof coal thicknesses within surrounding entries, (2) increasing pump pressure and thus shield set pressures (3) diligently monitoring shield set pressures and longwall extraction horizon, (4) installing additional cable bolts and roof screening to prevent progressive failure of the immediate headgate roof, (5) fully-grouting supplemental cable bolts to improve headgate support stiffness, and (6) gluing the headgate roof within the recovery areas with polyurethane. As a result of these collective efforts, longwall recovery delays at Bailey Mine were reduced from 21 days in 2006 to nearly zero in 2009.

Jan 1, 2009

By J. S. Hastings

Tertiary calc-alkalic to alkalic rocks of the Little Rocky Mountains in north-central Montana host low-grade heap-leachable gold-silver deposits being mined by Pegasus Gold Corporation. Total production from 1884 through 1985 is estimated at 22,625 kilograms (727,414 ounces) of gold. This includes 10,774 kilograms (346,400 ounces) recovered by Pegasus between 1980 to 1986 from 20,318,000 tonnes (22,396,000 tons) of ore grading 0.960 grams of gold per tonne (0.028 ounces per ton). Silver production during this latter period was 24,556 kilograms (789,500 ounces), but reliable silver statistics prior to 1980 are not available. Ore reserves as of January 1, 1986, were estimated to be 35,380,800 tonnes (39,000,000 tons) grading 0.720 grams per tonne (0.021 ounces per ton). Present ore production is 5,533,920 tonnes (6,100,000 tons) per year at a 0.45 to 1 waste to ore strip ratio. Current annual metal production is about 2,644 and 5,288 kilograms of gold and silver respectively (85,000 and 170,000 ounces of gold and silver respectively). The Little Rockies were formed by a calc-alkalic to alkalic magma penetrating through the Precambrian basement into the overlying Paleozoic and Mesozoic sedimentary rocks. This intrusive center is Dart of the Central Montana Alkalic Province, a region comprised of twelve separate intrusive centers aligned in a northeast trending belt measuring 200 by 400 kilometers (124 x 248 miles). The ore deposits are structurally controlled epithermal systems which vary from deeper narrow veins to shallow, wide, low-grade stockworks, breccias and intensely fractured "sheeted" zones. The shallow types are now being exploited. Primary mineralization consists principally of gold and silver associated with pyrite, native gold and silver, sylvanite, calaverite, and hessite. Alteration is broadly classified as weak argillic. Pyritization, kaolinization, silicification and feldspathization are the dominant forms of alteration. Fluorite is a common hydrothermal gangue mineral.

Jan 1, 1987

By James R. Brown

Mount Isa Mine should be regarded as a large mining complex rather than one mine. This arises from the geography, variety and extent of the orebodies, the mining methods, and the use of 14 shafts for ventilation distribution. A brief resume is presented here since comprehensive descriptions of lead-zinc mining methods {11}, copper mining methods {2 }{3}, geology 241, stope fill {5} and ventilation techniques {6}{7}, have all been published in the last five years. Mining extends over a north-south strike length of 2.5 miles (4 Ian) with a maximum width across dip approaching 3 200 ft (1 Ian). Current mining is to a depth of 3 150 ft (960 m) with the ore hoisting shafts extending 660 ft (200 m) deeper. The composite longitudinal section, Figure 1, shows a representational disposition of the copper and lead-zinc-silver orebodies in the central shaft complex where the main service and hoisting shafts are located. To the south the X41 man and materials shaft provides access to the copper area. The mine layout is typical of high tonnage track- less mines, utilising a large diesel fleet, raise- borers and some large diameter hole stope drilling. Mining methods include sublevel open stoping, slot and massfire, and a trial vertical crater retreat in the copper ore, and sublevel caving, sublevel open stopes with and without rib pillar recovery, and mechanised cut and fill in the numerous lead orebodies. All ore reports to one of the three crushing systems located below 19 level in the central shaft complex. Copper ore is hauled exclusively along the 19 level computer assisted Rockflo haulage system, and lead-zinc-silver ores report via central orepasses from Granby haulages on 13 level and 15 level. Tonnages hoisted during the 1977178 financial year were 5.0 million for copper at 3.2%. and 2.3 million for lead-zinc-silver at 7.8%. 6.3% and 7.06 oz/ton (216 g/tonne) respectively.

Jan 1, 1980

By S. S. Sephton

The La Perla Mine, owned by Altos Hornos de Mexico, S.A., is located approximately 100 miles east of the City of Chihuahua in the State of Chihuahua, Mexico. The mine began operations in 1958. Existing ore beneficiating facilities, consisting of heavy media and jig plants, upgrade the ore prior to shipment by rail to the Altos Hornos steelmaking complex in Monclova. Sizable reserves of two distinct ore types, which were not amenable to treatment in the existing beneficiating plant, or usable in the blast furnaces, have been mined and stockpiled in order to uncover the treatable ores. One of these ore types has been labeled "Diseminado" ore, and is low grade containing approximately 42% Fe with sulphurs ranging from 1 to 2%. The other ore type has been labeled "Pulverulento" ore, and is high grade containing approximately 65% Fe and 0.1% S, but at 80% minus 325 mesh, is too fine grained for efficient sintering. Late in 1968, Arthur G. McKee & Company became involved with the problem of improving the above ores for their efficient and economical use in Altos Hornos&apos; blast furnaces. Early in 1969 representative samples of Diseminado ore were obtained for laboratory bench-scale testing at the University of Minnesota, Mineral Resources Research Center. Concentration tests incorporating magnetic roasting, wet magnetic separation, high intensity separation, high tension magnetic separation, anionic flotation of apatite, cationic flotation of silica and oleic acid flotation of iron were performed. Laboratory testing was concurrently carried on at La Perla Laboratory, which resulted in plans to construct a 10 TPD pilot plant. The pilot plant was operational in September, 1969. Analyzing laboratory results as well as pilot plant results, Altos Hornos and Arthur G. McKee & Company metallurgists agreed that the most promising flowsheet for the low grade Diseminado ores entailed wet magnetic cobbing, desliming, and oleic acid flotation of the non-magnetic fraction. A combined concentrate of

Jan 1, 1972

By G. W. Kenzy

Recently, in the United States, questions of possible deleterious synergistic health effects of the gaseous and particulate components in the diesel exhaust and mineral and coal dust have been the impetus for extensive research by several agencies. At the present time, diesel engines are tested and approved for use in gassy and non-gassy underground metal and non-metal mines under Parts 31, 32, and 36 of Title30 of the Code of Federal Regulations. Diesel-powered equipment for use in underground coal mines, though not explicitly addressed in the law, is administered under Parts 32 and 36 of Title 30, with Part 36 being applied in the case of equipment working inby the last open crosscut or in the return airways. Operation of diesel equipment in underground mines has the potential for serious health and safety hazards from the gases, vapors, and particulates in the exhaust. Therefore, various countries have rules and regulations for the safe deployment of diesel equipment. The applicable laws and regulations from several countries who have long experience with diesel-powered equipment in their mines are reviewed. Four major areas have been addressed: (1) testing and approval procedures of diesel engines, (2) ambient mine air quality specifications, (3) frequency of sampling and location of samples, and (4) air quality specifications in splits where diesel-powered equipment are operated. The review indicates that most regulations generally consider four possible hazards: (1) toxic components in the engine exhaust, (2) ignition of flammable atmospheres by the engine or electrical equipment, (3) fire hazards presented by the engine fuel oil and by combustible material that might come in contact with the equipment, and (4) mechanical hazards. There is a remarkable similarity in the laws with regard to engine design, testing and approval procedures. However, the aspects with regard to mine air quality and quantity are quite variable-- from a general statement to very specific standards for many different diesel exhaust constituents. However, the laws with regard to synergistic effects of diesel exhaust components and other mine air contaminants are an exception.

Jan 1, 1980

By Nicola Beltrandi, Andrea Pigorini, Holad Mohamed Dahir, Ezio Pedone

"Genoa is a very distinctive city located between mountains and the sea and infrastructural upgrading works often have to deal with the intersection of existing infrastructures. This is the case for the new railway tunnel construction between the stations of Brignole and Principe which under-cross two existing double-track tunnels in operation. The latter have been constructed with masonry bricks and the vertical distance between old and new tunnels is approximately 1m. Due to rock characteristics and the urban environment, stability and vibrations control are the main issues. Consolidation work with the fore-poling method and a specific sequence of excavation, primary lining and final lining support have been designed to assure stability and settlement control. A hard rock road-header has been used to assure vibration control. Finally, a real time monitoring has been implemented. The article presents monitoring and back-analysis results of the under-crossing of the existing tunnels. GENERAL LAYOUT OF WORKS The Genoa railway junction constitutes an integral part of the Ventimiglia-Genoa-Novara-Milan railway line route and it is included amongst the railway systems of the Tyrrhenian-Northern European multi-modal corridor (corridor of the two seas or corridor VII Genoa-Rotterdam). The main aims of the project concern the upgrading of the existing lines and the separation of the long-distance passenger and freight traffic flows from those of a regional and metropolitan type. The project includes: •,Completion of the connection with the port of Genoa Voltri and the Italy-France coastal route. •,Interconnection with the future Terzo Valico dei Giovi mountain pass route towards Milan. •,Upgrading of the Genoa Voltri – Genoa Brignole main line to four/six tracks. Rearrangement of the systems at the Genoa Voltri, Genoa Sampierdarena and Genoa Brignole Stations, reorganisation of the services in the Genoa Terralba area and interchangeability with the metropolitan system complete the design activities. The contract which includes civil and technology works is divided into four construction lots (ref. Figure 1):"

Jan 1, 2016

By C. I. Walker

"Understanding the influence of slurry particle size on wear is essential to maximising the life of centrifugal pumps operating in mineral processing plants and for hydrotransport duties. Particle size influences not only the wear rate but also the wear pattern in pumps. Complicating the situation is the different relative wear rate for different pump parts depending on particle size. A simple Slurry Wear Type (SWT) number based on particle size and size distribution is proposed as a means for categorising slurry pump wear patterns and optimising pump application and material selection. INTRODUCTION The wear of centrifugal slurry pumps in mineral processing and hydrotransport can be quite severe and is one of the major cost concerns of plant operators. Some typical worn slurry pump parts made from high chrome white iron are shown in Figure 1. Erosion wear rates of up to 2 mm/day are not uncommon [1].Centrifugal slurry pumps are required to handle solid-liquid mixtures with a very wide range of particles extending from sub-micron size clay through to 200mm and larger cobbles. Particle size distribution can also vary widely from uniform and narrow (such as graded sand) through to very broad (such as grinding circuit slurries). Slurry particles may also undergo size change due to attrition during the pumping process. The major wearing parts in a slurry pump are the impeller, side liners and casing liner. These are shown with reference to a Warman® MC centrifugal pump in Figure 2. While many particle properties (including size, shape, hardness, density and concentration) influence pump wear, this work will consider only the effect of particle size as it is the major determinant of wear characteristics. Particle size influences the wear pattern, material performance and relative component wear rate in centrifugal slurry pumps. SLURRY WEAR TYPE (SWT) BASED ON PARTICLE SIZE Soil and grain size classification systems abound. Many have different limits to the ranges for a particular classification, albeit not too"

Jan 1, 2018

By Henryk Bystron

The underground fire areas are formed as a result of failure of an active fire extinguishing in mines. Such areas bring about a fire hazard for the work safety and for the mining operations. For liquidation of fire areas it is necessary to create conditions under which a possibly small amount of air is flowing to the fire. To achieve this end, isolation methods are used which consist in erection of full stoppings of various types, sealing practically the fire areas. These methods usually fail in oases when the coal seam is thick and the fire area is situated between the intake shaft and the outtake shaft in which a high-pressure fan is in operation. In such oases ventilation methods based on the balance of aerodynamic potentials in fire areas are to be used. For a very long time the isolation and ventilation methods have been developed in the world mining, No sooner than since 1980 the aerodynamic potential has been used in ventilation methods [1,2,6]. So far, the aerodynamic potential was called in different ways and was determined by different formulae which gave its numerical values more or less approximative. Nevertheless, even in situations featuring by a lack of sufficient theoretical bases of the aerodynamic potential the ventilation methods brought considerable profits in the field of safety in mines and of economics in mine ventilation [1-6,9,10]. The increase in the depth of underground mines and their equipment with expensive machines (apparatus) brought about that the Central Mining Institute at Katowice undertook research works which are crowned by the theory of the aerodynamic potential in mine ventilation networks [7]. The use of this theory in the mentioned ventilation methods will increase their effectiveness. Since the theory will be published in the III rd quarter of this year, we cite in the present paper the formulae and relations associated with this theory which are indispensable to present the balance of aerodynamic potentials in the fire areas in their control by ventilation methods.

Jan 1, 1980

By A. L. Ling, A. K. Janzen

"Design of effective mine water treatment plants depends on the ability to reliably predict treatment outcomes, but systems with multiple chemical and physical treatment processes and recycle loops can be difficult to model. GoldPHREEQC is a modeling framework that integrates mass and flow routing capabilities of GoldSim software and water quality calculations provided by PHREEQC, and is well-suited to modeling parameters of interest in the mining industry, especially metals and sulfate. Physical processes such as membrane separation and greensand filtration are modeled by defining mass rejections for each parameter and flow routing based on vendor projections and bench- or pilot-scale equipment testing. GoldPHREEQC models chemical precipitation processes such as HDS metals removal and gypsum precipitation by (1) performing surface-aging and solubility calculations in PHREEQC and (2) using the GoldSim framework to direct supernatant and precipitate to subsequent process steps. Users can apply this modeling framework to predict effluent water quality, chemical requirements, sludge production, and required equipment capacity to support design, troubleshooting, and cost estimating. INTRODUCTION Design of effective mine water treatment plants depends on the ability to reliably predict treatment outcomes, but systems with multiple chemical and physical treatment processes and recycle loops can be difficult to model. GoldPHREEQC is a modeling framework that integrates mass and flow routing capabilities of GoldSim software (1) and water quality calculations provided by PHREEQC (2), and is well-suited to modeling treatment of parameters of interest in the mining industry, especially metals and sulfate. GoldPHREEQC can also be applied to other water treatment scenarios using inorganic reactions and processes. The GoldPHREEQC model framework moves water and mass between specified model nodes and calculates specified reaction and water quality outcomes. It can be organized to provide flow, load, and concentration information for each location, including effluent and byproduct streams, and outputs can be adapted to include power and chemical costs."

Jan 1, 2018

By Hans Ehdwall, Erling Strandon, Friedrich Steinhäusler, Victor A. Leach

INTRODUCTION The basis for any measures in radiation protection is the quantitative assessment of the radiation exposure. Due to the extensive requirement in health physics manpower and related cost it is necessary to develop certain criteria regarding the necessity of monitoring and the selection of population groups to be monitored. Depending on the overall objective of the particular programme, the specific requirements for the measurement of atmospheric levels of radon, thoron and their daughters for practical radiation protection purposes differ significantly for those in the case of research applications, such as use of data for epidemiological studies. As part of the OECD-NEA Programme on Radon Dosimetry and Monitoring Task Group 1 reviewed available models for lung dosimetry in the case of inhalation of radon 222, radon 220 and their daughters (James et al., 1981). Using defined reference atmospheres for underground- and open-pit mining conditions as well as for dwellings, normalized conversion factors were calculated for the mean bronchial dose (mGy) per Working Level Month exposure (WLM). Task Group 2 discussed the features and adequacy of the Working Level (WL)-concept as a physical correlative of the absorbed lung dose and its limits of confidence and accuracy (Johnson and Leach, 1981). The WL-concept was found acceptable for radiation protection purposes provided that modifying factors like particle size, unattached fraction and respiratory minute volume did not cause the effective dose equivalent per WLM as calculated by either the James-Birchall or Jacobi-Eisfeld lung models to be more than 50 % above that given by ICRP of 0.01 Sv/WLM. For application in epidemiological studies the WLconcept is considered acceptable if the calculated absorbed dose to the tissue does not vary by more than 50 % (at the 95 % confidence level) from that given for defined reference conditions. In the following, objectives and requirements for the measurement of radon, thoron and their daughters are discussed for operational health physics routine and special research applications according to the scheme outlined in Fig. 1.

Jan 1, 1981

By B. K. Sternberg

Since 1986, we have developed a series of electromagnetic (EM) sounding systems at the Laboratory for Advanced Subsurface Imaging (LASI). These may be categorized by their frequency ranges: low frequency (LF, 30 Hz to 30 kHz), medium frequency (MF, 1 kHz to 1 MHz), and high frequency (HF, 30 kHz to 30 MHz). We have applied these EM systems to a variety of targets, including: mapping of plumes of contaminated groundwater, tracing leachate for an in-situ leaching operation, locating buried hazardous waste, identifying subsidence-prone zones and detecting buried voids. These systems are also applicable to exploration for ore bodies. Currently, our sounding system uses a vertical magnetic field vector. Previous systems of this type required a slow and relatively inaccurate manual rotation of the sensing coils. The systems also used occasional calibrations of the measuring system. We have developed a 3-dimensional mathematical rotation procedure for the data, as well as a simultaneous, high-accuracy, calibration method. These new developments have greatly increased the speed of the measurements, as well as improving the accuracy of the ellipticity data. We use stepped-frequency measurements along with narrow-band filtering to allow accurate measurements, even in high-noise areas. We typically obtain ellipticity measurements at eleven frequencies and along densely sampled profile lines. We use neural networks to help interpret the measured ellipticity patterns. Neural networks can be trained to relate the measured ellipticity patterns to earth resistivities or to discrete targets buried in the earth. The neural network training may use theoretical EM responses calculated from computer codes for relatively simple structures. The theoretical EM response for many complex targets that are of interest cannot currently be reliably calculated, even with the largest supercomputers available. We have therefore chosen to do some of the training using theoretical EM responses generated in a full-scale modeling tank located at our Avra Valley Geophysical Test Site. We have also developed data-visualization software to help interpret the large data sets produced by this system.

Jan 1, 1997

By Kadri Dagdelen, Thys B. Johnson, Salih Ramazan

Long-term production scheduling design is a very important part of mining because it determines the economic outcome of a project There have been many attempts to solve the optimum pit scheduling problem, but there has been no success in developing a scheduling method to give optimum results in maximizing net present value of a mining project. Open pit production scheduling problem can be formulated as a mathematical programming problem and solved using Mixed Integer Programming technique. However, it is not possible to solve the formulation within a reasonable time since the number of integer variables required for the mathematical model is too great to do that by today&apos;s available computer technology. There- fore, a methodology is required to combine, or aggregate, the mining blocks and to decrease the number of integer variables in scheduling without losing the optimality. Therefore, the fundamental tree concept was developed in this paper to combine the blocks. A fundamental tree is defined as any combination of blocks such that: 1. the blocks can be profitably mined, 2. the blocks obey the slope constraints and, 3. there is no subset of the chosen blocks that meets 1 and 2. A Linear Programming (LP) formulation is developed as a mathematical model to find a set of fundamental trees that exist for a deposit. Since the blocks are combined to form the fundamental trees, the number of variables required for the scheduling model is decreased significantly. This decrease in the number of variables makes it possible to mathematically formulate the multi-time period scheduling problem as a Mixed Integer Programming (MIP) model. A case study is performed on a multi-mineral copper deposit in Peru, South America. NPVs of annual after-tax cash flows generated based on the schedule provided by the "Fundamental Tree Algorithm" is compared with NPVs resulted from the schedules coming from three of the computer packages presently available to the mining industry. These are Mintec&apos;s M821V, Earth- work&apos;s NPV Scheduler, and Whittle&apos;s Milava open pit mine schedulers.

Jan 1, 2002

By A. Gupta, S. C. Srivastava, K. K. Saroj

Bacterial degasification of methane and conventional methane drainage for generation of power have become accepted practice. Comparative economies of both the techniques have been described. Authors have discussed an alternative technique, involving complete methane biocycle. The first stage of the entire process involves gasification of coal using a consortia of bacteria to generate methane. The generated methane has been proposed to be pumped,as in conventional methane drainage. Technique described is basically similar to underground coal gasification, with the difference that in place of coal combustion, degradation of coal to lower molecular weight compounds by one set of bacteria and then methanogenesis by methanogens, producing methane have been described. Brief account of communities of bacteria that may be employed have been dealt with. Three arguments in favour of proposed technology as an alternative to conventional coal mining are: 1.Total elimination of hazardous operation. 2.Availability of power plants based on methane drainage, assuring comparative economies. 3.Possibility of utilisation of fuel cell technology for power generation giving higher efficiency. All the three phases of complete blocycle viz (1) methane generation from coal (ii) conversion of methane to hydrogen and oxygen (iii) conversion of products so obtained to methane, thereby completing the cycle have been discussed. INTRODUCTION Drainage of methane by conventional pumping process (Boxho,et.al.,1980) not only is helpful in maintaining safe extraction of coal, but with utilisation of extracted gas for power generation, also helps in over all economy of coal mining. This is gradually becoming standard practice for mining of coal in highly gassy mines. An alternative technique (Thakur et. al., 1991) of bacterial degasification of coal seams is also gradually gaining ground. The bye products of this process that is carbondioxide and water, do not contribute towards economy of coal extraction process. However the technique has its own advantage particularly in goaf area for avoiding fire hazard and drainage of methane from coal seams prior to initiation of mining operation. Either of these techniques could be applied in specific situations with success.

Jan 1, 1993