Search Documents

By Scott G. Britton

This chapter discusses the necessary construction techniques for installing coal mine ventilation devices. Included in the discussion are the major air controlling devices called over- casts, regulators, stoppings, and doors. Under-casts, although a valid device, are used infrequently in coal mining and are not discussed here. Typically, coal mines require a great many ventilation devices to control the air movement. Post-I969 mines have had to design their air systems to comply with the Federal Coal Mine Health and Safety Act (CMHSA) as discussed in Chap. 1. Pre- 1969 mines have had to redesign major portions of their systems to comply with the basic components of the law such as separation of air courses, single unit split ventilation, and minimum air quantities. It is not uncommon, therefore, to find a large mine (2.0 Mt/a) requiring several hundred overcast installations (permanent, as well as repeat construction), plus doors and regulators placed among a thousand or more stoppings. When each of these devices is subject to leakage from installation and weathering defects, the importance of effective construction becomes evident. An historic rule of thumb for average mine ventilation says that about 70% of all the air pressure generated by the mine fan is lost between the portal and the working faces. Of course, this rule is subject to many factors, but the message is clear: there is a tremendous inefficiency in controlling leakage through common air devices. This chapter strives to present a standard approach and design alternatives which can go a long way in reducing this leakage, and hence, ventilation costs. Historically, mine ventilation has progressed from natural, or draft ventilation, to fire-induced ventilation (Fig. l), furnace-fired centrifugal fans and finally, to today's modem mine fans. Underground controlling devices have been in use in the coal mines since the late 1600s, but the CMHSA of 1969 was the real turning point for mine ventilation. Minimum quantities and velocities of fresh air were required for mining, forcing coal operators and engineers to reevaluate and improve their systems. As a consequence, the cost for ventilating air increased. Today, companies face a variety of choices among design alternatives, materials, labor, and costs of ventilating devices for their mines. The best approach for any individual company or mine is determined by (1) the needs of the mine, and (2) the local design parameters. In my discussions of ventilation construction I shall be fairly general in terms of device installation steps, where specifics are warranted for clarification, I will include this information.

Jan 1, 1983

By Jake Beale, Joe Wickline, M. Van Dyke, Ted M. Klemetti

A longwall coal mine in southwestern Virginia mining the Pocahontas #3 Coal Seam experienced a history of mining-related seismic events. The events were never large enough to cause concern until three major events occurred recording 3.4, 4.3, and 3.4 ML in 2005, 2006, and 2007 respectively. Two of the seismic events generated an air blast which damaged stoppings which fueled a mine fire in 2005 and 2007. The mine responded to the events by narrowing the longwall widths, changing ventilation controls, installing a 7-sensor seismic system around the active panel, and creating a mining hazard map to avoid similar geology in the future. All of the actions taken have prevented seismic activity from impacting mining operations, but it did not prevent other large seismic events from occurring (Van Dyke et al., 2018). In 2016, another large seismic event, measured at 3.7 ML, occurred in the gob that was reported by the local media and recorded by the United States Geological Survey (USGS). While the event did not directly impact mining operations, mine management wanted to know where and under what conditions could large seismic events occur in the future. The National Institute for Occupational Safety and Health (NIOSH) became involved to help understand what conditions precipitated these events so that future mine design could more accurately assess seismic hazards and reduce the risk to mine worker safety. Researchers at NIOSH and mine management created a seismic forecasting map that combined three factors: (1) overburden thickness, (2) sandstone thickness, and (3) the expected caving height of the gob. The criteria were developed based on the geologic data the mine collected from core drilling, e-log analysis, and fiberscope observations. The forecast map was able to provide an accuracy of 72%–85% of events 1.5 ML or greater and 100% accuracy of events that were 3.0 ML or greater based on historical data. The seismic forecasting map was applied to the entire future mining area to show areas where seismic potential could be the greatest based on current mine design planning, ultimately improving the ability of the mine operator to assess the seismic hazards surrounding active and future mining areas (Van Dyke et al. 2018). Following this research, the seismic forecasting map was implemented into the mine’s hazard recognition program and is continuously updated and evaluated prior to mining each longwall panel. This paper will cover in more detail how the seismic and lithologic data was processed and how the mine implemented a new seismic mitigation program based on the forecasting results.

Apr 26, 2022

By David A. Hedderly-Smith

Sealaska Corporation, the Alaska Native Regional Corporation of Southeastern Alaska, was organized under the laws of the state of Alaska pursuant to the federal Alaska Native Claims Settlement Act of 1971. Large areas of Sealaska's 630,000-acre (250,000 hectare [ha]) fee subsurface holdings are underlain by carbonate, and while much of this material is assumed to be common variety limestone and lesser dolomite, at least two areas in the Silurian Heceta Limestone contain high-quality limestone at tidewater. This limestone has many potential commercial uses. On northern Prince of Wales Island, about 90 miles (144 km) north-northwest of Ketchikan, resource development at Sealaska's Calder deposit has established a reserve of 13 mil- lion short tons (st) (12 million metric tonnes [mt]) of carbon- ate rock containing an average of greater than 98 percent CaC03, approximately 0.5 percent MgO, less than 0.5 per- cent Si02, and approximately 0.15 percent Fe203, with insolubles averaging less than 0.5 percent and an average Hunter Brightness of 92.07 for the -150 mesh grind (with a bright- ness cutoff of 90). The deposit is open at depth and to the south. Ultimate reserves will likely be several times those currently established. In 1998, Sealaska began mining the Calder deposit, with about 100,000 st (90,000 mt) produced, and also completed a marine terminal one half-mile (800 m) from the deposit. The terminal can load ships up to 680 feet (200 m) in length at a rate of 2,000 st (1,800 mt) per hour. 0 m) in length at a rate of 2,000 st (1,800 mt) per hour. On Dall Island at Breezy Bay, about 60 miles (100 km) southwest of Ketchikan, Sealaska has identified a limestone reserve in excess of 150 million st (135 million mt) that (based on 18 surface samples distributed evenly over about a section of land) contains about 98 percent CaC03, and less than 0.5 percent MgO, 0.5 percent Si02, and 0.15 percent Fe203. Brightness of the Breezy Bay carbonate is considerably less than at Calder. Five samples of brighter material from Breezy Bay returned brightness analyses in the high 80s and low 90s; average brightness is probably below the mid- 80s. Sealaska has also identified a deposit containing more than 19 million st (17 million mt) of similar rock near View Cove, a few miles south of Breezy Bay.

Jan 1, 2001

By Ruifeng Li, Yanghui Ren, Hua Gao

"Since entering the new century, China’s coal industry has witnessed the rapid development, and provided a reliable energy supply for the national economic and social development. But after the “golden decade” of rapid development, the coal industry now is facing overcapacity, low industrial concentration and production efficiency, high pressure of production safety and environmental protection and other prominent issues. Based on defining the connotation of highly-efficient recovery of coal resources, this paper established the relevant 8 indicators to reflect the highly-efficient recovery level of coal resources, summarized the present situation of China's coal resources recovery and the main problems, analyzed the development environment of China's coal industry under the new situation, and finally put forward the strategic measures to promote highly-efficient recovery of coal resources in China.1. Background Coal is the main energy in China. Since entering the new century, China's coal industry has made significant progress, and the level of production safety, resource recovery rate and mining mechanization increased significantly, which provided a reliable energy supply for the rapid development of the national economy. However, due to the changes of China's economic environment, slow growth of energy demand and other factors, some prominent contradictions in the coal industry have significantly restricted the healthy development of the industry. The first problem is serious overcapacity. In the past few years, 16 industries including coal, electric power, chemical and others have invested in coal mines. It is reported (Han 2016) that only during the nine years from 2005 to 2014, the fixed assets of coal industry increased totally more than 3.3 trillion RMB, which brought a large number of production capacity. Affected by the slowdown of economic growth and energy structure adjustment, Chinese coal demand has reached the peak platform and caused the overcapacity of coal supply, so shutting down the backward capacity is the most important task in the future. The second problem is the low efficiency of coal production. There are about 4.3 million coal mine workers in China, and the annual coal production per capita is less than 900 tons, while it was reported (EIA 2016) that the annual production per capita in the United States is more than 10 thousand tons. The third problem is that the green coal resources are not rich. Among the 1.53 trillion tons proven reserves, only about one third are green coal resources in accordance with the principle of ""safety, technology, environment and economy"". The coal resources with high quality and easily mining conditions are not abundant."

Jan 1, 2017

By R. C. Fox

The geophysical aspect of reconnaissance marks the beginning of extensive computer applications supporting development of a mine. Although there are some storage and retrieval applications in geology, and some statistical analysis in geochemistry, large-scale compilation, reduction, and interpretation of mineral resource data are initiated in reconnaissance geophysics. The reasons for this fact are quite simple. Geophysics is oriented toward quantitative evaluation of areas of interest, and methods of data collection are automated to the extent that large amounts of analog and digital information are recorded. The large volume of data must be interpreted in a reasonable time. Furthermore, some modeling problems involving complex numerical solutions could not be attempted without the computer. Therefore, the computer is essential to the success of an exploration project using geophysics. For example, aeromagnetics is a common technique for reconnaissance examination of areas associated with sulfide systems and porphyry deposits. An area covering 161 X 161 km (100 X 100 miles) may be flown with a 1.6-km (1-mile) line spacing yielding 10,000 line miles (16,093 km) of data. If only 10 measurements are recorded per mile, 100,000 data points, including location and magnetic field intensity, must be reduced and stored for quantitative interpretation. Computer applications often represent a significant investment in manpower and hardware. It is desirable, therefore, to initiate an engineering approach to the application of computers to geophysics. By this it is meant that computer programs and systems should be formulated, developed, and implemented in a disciplined manner such that their usage is dependent only on the application and not on the individual doing the programming. In other words, computer application, development, and usage should evolve beyond the personal gadget phase to an important applied technology. Geophysics has evolved over the past two decades in a course parallel to computer hardware development. During the sixties, the computer became large enough and fast enough that complex models required by geophysics could be solved. Automation also relieved the geophysicist from routine manual calculations. During the seventies, computing power in¬creased and applications expanded from two-dimensional problems to three-dimensional modeling. Moving into the eighties, as computer hardware costs will significantly decrease, the major expense of computing will be the manpower required to develop, implement, and use an application; therefore, improved programming techniques and applications software engineering methods will be used to optimize and preserve this investment. This chapter presents a general overview of computer methods in geophysical reconnaissance; it is divided into two parts: geophysical methodology and software engineering.

Jan 1, 1979

By Bing Wang, Jingli Fan, Qinying Song, Fengyu Li, Xian Zhang

"With the background of water shortages and serious water pollution, issues of water involved in energy exploration and utilization have become critical problems affecting urban water usage. In order to identify the relationships of the energy-water nexus, this paper characterizes the energy-water nexus literature using a bibliometric method and based on the Chinese National Knowledge Infrastructure database platform. The results reveal that 1) Scientific outcomes in this field have increased sharply since 2003, with a slightly higher growth rate than that of general disciplines. 2) China Water Resources, Yangtze River and Express Water Resources & Hydropower Information are the dominant journals, and the main research fields include industrial economics, environmental science, and management, among other disciplines. 3) Hohai University, the Chinese Hydraulic Engineering Society, the Institute of Geographic Sciences and Natural Resources Research, and the Changjiang Water Resources Commission are the main research institutions in this field. However, the proportion of publications of these institutions is not high, which suggests that there is no institution dominating this field. 4) According to the keyword analysis, the hot spots in this field include ecological environment, sustainable development, environmental protection, climate change, etc. Energy-mining related keywords have increased over time, implying that the energy-water nexus from the perspective of the energy exploitation industry can become a key issue. At the same time, the frequency of keywords related to sustainable development has been maintained at a high level, and the studies concerned with the impacts of climate change were introduced into this field relatively late. The conclusion of this study provides a foundation for a comprehensive understanding of the current situation as well as for further research in the energy-water nexus field.Introduction As an important strategic resource for national economic and social sustainable development, water has been increasingly focused on by the Chinese Government. Over the next decade, the total water demand of China will continue to grow steadily, which lead to a significant trend of increasing water consumption in the future (Zhang 2013). To reasonably exploit, utilize, conserve and protect water resources, the Water Law of the People's Republic of China was enacted by the members of the 9th National People's Congress Standing Committee in 1988 and after multiple revisions, the latest of which, in September 1, 2016, has involved water infrastructures in the national economic and social development plans of the government at all levels and regulated the rationale for water engineering construction. Thus, in the context of serious water shortages and water pollution, China’s government has taken several measures to make rational use of water resources."

Jan 1, 2017

By Annan Cook

J.R. Atkinson, office engineer to Kennecott Copper Corp., summarized data on the Mineral Park area [Wallapai (Chloride) Mining District, Mohave County, Arizona, Fig. 1] and submitted it to the New York office in 1950. He recommended an examination. Weston Bourret, a Kennecott geologist, accompanied by B.S. Butler, the well known former US Geological Survey geologist, examined the larger of two hydrothermally altered areas in Mineral Park that same year. Bourret recommended that the property be optioned and mapped. Georges Ordonez, Kennecott's chief geologist, after a field examination, agreed with Bourret's conclusions At the end of the summer of 1951, Annan Cook (another Kennecott geologist) accompanied Ordonez to the property prior to starting a mapping program. At Ithaca Peak, the structure, alteration, and reddish-brown coloring in leached cavities-hematite, jarosite, and goethite with minor copper staining - made an interesting target. The Peak, which has since been mined, was a Laramide quartz monzonite porphyry grading into quartz porphyry, penetrating Precambrian rocks. Turquoise had been mined from several workings on the Peak. Surrounding the central area of alteration, but mainly to the northwest, there were many long-abandoned underground workings mined for zinc, lead, gold, silver, and copper. To the west of Ithaca Peak within the main area of alteration, surface evidence of a chum drill hole suggested interest in the disseminated mineralization probably prior to World War II. A topographic and geologic survey of the altered Ithaca Peak area was initiated by Cook in September 1951. He was assisted by Richard Vosburgh, field engineer, and by four geologists: Charles Goddard, III, Donlon LoBionda, Keith Martin, and A.T. Stone. When Cook returned to New York, Vosburgh was left in charge. Mapping continued and diamond drilling took place during the winter of 1951-1952. Drill sites were selected entirely on the basis of surface geology. Five drill holes, including a flat hole, located around the flanks of Ithaca Peak, averaged about 183 m (600 ft) in length. A sixth hole caved at less than 60 m (200 ft). The best values obtained were in the first hole (-45°): 90 m (300 ft) averaged 0.62% copper and 103 m (337 ft) averaged 0.041% molybdenum. In another hole, 43 m (142 ft) averaged 1.09% copper and 0:023% molybdenum. The values of copper and molybdenum in these two holes were generally higher than in the remaining holes, although molybdenum values were always around 0.024% or better. The New York office decided, however, to abandon the project even though the remaining field crew of three had recommended more drilling.

Jan 1, 1991

By V. Matthews

"INTRODUCTION Typical grinding electrification requirements are defined by high power, constant torque and slow speed. Dual pinion mills also include a need for tight tolerances in torque between the two motors, to avoid overloading any single motor. Standard induction (asynchronous) motors have often been used but only in combination with mechanical gearboxes (reducers), required to reduce process speed to the correct level for mill pinions. The gearbox introduces added system complexity, capital cost, maintenance and energy cost due to mechanical losses. SYNCHRONOUS AND ASYNCHRONOUS MOTORS Elimination of the gearbox requires a motor designed to operate at a very low speed (rpm). Traditionally, mill motor requirements were best served by synchronous motors. The benefits of synchronous motors include- • Higher Efficiency (no conductor losses in rotor) • Very high power at low speed • Flexible Power factor (leading or lagging) • Constant speed (not load dependent) • More accurate speed control Synchronous motor cost is higher due to construction complexity, need for exciter and excitation panel, brushes, brush lifters. Figure 1 represents the equivalent circuit for a synchronous motor.Asynchronous motors, also known as squirrel cage induction motors, are singly excited, per Figure 2, the resulting equivalency circuit is less complex and only in need of a single voltage source.Commonly, a DC voltage supply is connected to the rotor (both physically and electrically) via brushes. The DC voltage enables the production of flux in a single direction. The brushes are connected to rings. The slip rings encircle the rotor but are insulated from the rotor. The slip rings are connected to a rotor winding known as a field winding. On large motors, brushless exciters are often used. A brushless exciter is a small AC generator whose field circuits are mounted on the stator and armature circuits are mounted on the rotor shaft. The exciter generator’s 3-phase output is rectified to DC by a 3-phase rectifier (mounted on the shaft) and fed into the main DC field circuit. It is possible to adjust the field current on the main machine by controlling the small DC field current of the exciter generator (located on the stator). [1] Brushless synchronous motors are often preferred over the traditional brush design but introduce additional complexity to motor construction in the form of additional windings and rectifiers comprising the excitation circuit. It stands to reason that because of the additional complexity, a synchronous motor will be higher in cost than an equally rated asynchronous induction machine."

Jan 1, 2015

By D. J. Benton, S. Finley, D. T. Orr, A. J. Chambers, M. A. Stepan

"Corrosion of ground support can lead to falls of ground that pose a significant risk to miner safety. To address this problem, the National Institute for Occupational Safety and Health (NIOSH) is investigating corrosion at the Hecla Mining Company’s Greens Creek Mine, located near Juneau, Alaska, USA. Field studies have used photogrammetry surveys to document welded-wire mesh corrosion, and laboratory studies at NIOSH’s Spokane Mining Research Division (SMRD) have investigated the effects of corrosion on ground support integrity. Findings show that (1) corrosion monitoring through photogrammetric methods may be effective for qualitative measurements of welded-wire mesh corrosion, and (2) there is a relationship between loss of load-bearing capacity and the diameter loss due to corrosion in welded-wire mesh. Photogrammetry results thus far have measured an apparent bulking of the corroded welded-wire mesh, and preliminary laboratory tests have investigated the relationship between the larger bulked and effective wire diameter. If this relationship is verified, these results may indicate that photogrammetry, when combined with the models produced in laboratory tests, could offer a means of monitoring corrosion levels, as well as rock rib deformation. INTRODUCTION Reducing the number of rock fall injuries and fatalities is an important part of the mission of the National Institute for Occupational Safety and Health (NIOSH) Spokane Mining Research Division (SMRD). Ground control using support systems to protect miners from rock falls is one of the oldest mining sciences, and considerable research has led to a variety of modern tools and methods in use today. Among these tools are rock bolts and welded-wire mesh, which are made from increasingly higher-strength steel grades to meet the increasingly demanding requirements of underground mines [1]. However, the benefits of these higher-quality support elements may be negated in corrosive mining environments. A better understanding of how corrosion affects the support capacity of ground support systems will assist engineers in determining when an opening is at a greater risk of falls of ground. Accelerated corrosion has been occurring in some areas of the Hecla Mining Company’s Greens Creek Mine near Juneau, Alaska, USA. Corrosion of ground support has resulted in two falls of ground occurring between April 2015 and March 2016. While these falls of ground did not injure any personnel, mine management recognized the high risk to miner safety and responded by actively undertaking a ground support rehabilitation program. Rehabilitation measures include the installation of both galvanized and coated, corrosion-resistant bolts and welded-wire mesh, depending on local conditions."

Jan 1, 2017

By M. M. Champion

INTRODUCTION Since the first introduction of explosives into mining operations, safety considerations have prohibited the use of machinery in association with the explosives. Only within the last 25 years has this situation changed appre¬ciably; the closest thing to "machinery" used by a powderman in the "old days" was his wooden tamping stick. With the blackpowder and dynamite used during the first 150 or so years of mining blasts, substituting a drill steel or a metal "spoon" invited serious disaster. With the advent of ammonium nitrate-fuel oil (ANFO) explosives (1950s) and water-gel explosives (1970s) for underground blasting, machinery started to play a large part in blasting procedures. The lower sensitivity of ANFO and water gels allows these prod¬ucts to be loaded in a variety of safe ways. Not only has this meant cost savings in labor and blasting materials, but it has also resulted in whole new mining concepts where the limitations of dynamite previously made those concepts uneconomical, impossible, or excessively risky. Increasingly (totally for some mines), the traditional tamping stick has given way to a variety of pneumatic machines for loading explosives and blasting agents. The resulting blasting operations have become safer, more efficient, less uncomfortable for personnel, and a major step forward in mining technology. ANFO LOADING EQUIPMENT Three basic types of loaders are used for ANFO explosives, these being the pressure-vessel loaders, Venturi loaders, and combination loaders. Pressure-Vessel ANFO Loaders ANFO consists of prilled ammonium nitrate (porous pellets I to 2 mm in diam) and fuel oil in the appro¬priate 94 to 6% blend. The material is fairly dry, pourable, and easily conveyed by an air stream. One device or system for handling (hole loading) ANFO is the pressure-vessel loader. ANFO is dumped into the vessel or "pot," and the vessel then is pres¬surized. The ANFO is conveyed out of the bottom of the vessel into a semiconductive hose that has been inserted into the blasthole. Fig. 1 illustrates a typical pressure-vessel loader in use. Applications: The use of pressure-vessel loaders is widespread in room-and-pillar mines, including salt, potash, trona, lead, and other rubber-tired mines where the heavy pressure vessels can be mounted on a vehicle for transport from face to face. The vessel often is large enough to hold eight or more 23-kg (50-1b) bags of ANFO, so several faces can be loaded before refilling. Pressure-vessel loaders also are suitable for effec¬tively loading long holes such as those that are 6 m (20

Jan 1, 1982

By M. Javier

"Mining is the main activity that supports civilization. Actual mining presents contradictory concept to the health of the planet. Its business model is linear, fragmented and characterized by inefficiencies in the utilization of water, energy and mineral resources which generate waste and pollution. Before mining begins, it is critical to determine the vulnerability of the ecosystem and after mining, it is critical to determine the depletion of nature. Attending to these vital matters will require quantifying and measuring them. The purpose of this study is to provide and establish the metric to assess the performance and manage a sustainable future for our existence and that of our planet. This index is defined to measure and control Nature Friendly Sustainability (NFS) based on understanding nature. This index will determine the condition of nature constructed on the measurement of physical, chemical and biological equilibrium. Proposing a new mindset for mining design to satisfy nature’s needs would be to offer the same opportunities to future generations. Hence, sustainability is synonymous with equilibrium under a limited ecosystem. Nature is interconnected. Finally, this index of NFS is readable, standardized and relevant to keep nature’s needs in equilibrium. Establishing and NFS index is the next metric for humanity. INTRODUCTION There are a multitude of definitions of what sustainability is. Most of them are defined in terms of the corporate entity from which they emanate. The classical definition of management states that, “if we do not measure it, we cannot manage it.” Management of ecosystems is the definition of sustainability. Indicators of quantity and quality of sustainability are vital in order to create a metric for sustainability. These indicators will measure the depletion and degradation of nature as they occur through human intervention. The first step is to create a metric of sustainability to simplify its definition. The definition of sustainability is based on whether or not you consider nature to be finite or infinite, which is described in Nature Friendly Sustainability (NFS) [1]. The definition of NFS applies to any anthropogenic activity with an understanding of the equivalent activity in nature. That is to say, human activity with nature requires balance and equilibrium in order to be sustainable. The importance of this equilibrium is quantified in a set of metrics in order to establish measurement and acknowledge indicators for our dependence on nature. Sustainability is synonymous with equilibrium in any ecosystem that is limited and fragile. In the graph is the explanation of sustainability definition. See Graph 1"

Jan 1, 2017

By Geno Saccomanno

INTRODUCTION Cancer of the lung in uranium miners has been reported by many authors. In fact, it has become a most popular subject for comment by environmentalists, health physicists, and newspaper writers. I believe it appropriate for me to discuss cancer of the lung in uranium miners in a general way commenting briefly on etiology, incidence, tumor cell types, and particularly, tumor development and treatment. Cytological development of cancer in its incipient stages, particularly the in situ stage, relates to potential cure with photoradiation, early diagnosis, and treatment. Our observations of the cytological response to this modality of diagnosis and treatment will be discussed briefly since this area will also be covered by Doctor Balchum. The cause of lung cancer in uranium miners is primarily due to two carcinogens; cigarette smoking and radon daughter radiation. Cigarette smoking has continued at the same intensity over time among uranium miners; about 60% of the miners are cigarette smokers and 40% are non-smokers. Radon daughter exposure to the uranium miner has varied from mine to mine, but over the last 20 years has been reduced to a minor fraction (.3 WL) of the level that prevailed in many of the mines during the 1950-1960 era when many of the miners were exposed to more than 10 WLM. Sputum samples have been examined on as many uranium miners as responded on the Colorado Plateau since 1956. Autopsy studies were done whenever this was permissible. In some instances, only tissue from a biopsy of a node or lung was available for study. Smoking histories were also taken. Approximately 200,000 sputum samples were examined and histological examinations of lung lesions were made from 312 cases. METHODS The method of sputum cytological collection and preparation was reported previously. I The lungs were fixed with formalin and prepared for sectioning by Dr. Oscar Auerbach with his block-section method. RESULTS Three-hundred-twelve lung cancers from uranium miners were examined. The tumor types and the age at death for each type, smokers and non-smokers, are given in Table #1. The incidence of the tumors in the smokers and non-smokers is given in Table #2. The incidence of small cell carcinoma of the lung has decreased from an incidence of 76% of all the lung cancers found in uranium miners to 22% of these lesions (Figure #1). The decrease in incidence of this tumor is probably due to decreased exposure to radiation in the mines.

Jan 1, 1981

By Jiang Su, Alan Bloodworth

"Composite sprayed concrete lining (SCL), consisting of two layers of permanent sprayed concrete separated by a layer of spray-applied waterproofing membrane, represents the latest development in SCL tunneling, but presents several challenges to designers. This paper aims to address the following issues: (1) how to simulate composite action, (2) behavior of a composite SCL tunnel, and (3) how to utilize composite action to achieve lining thickness efficiency. It firstly sets out the background to the composite SCL concept, and then presents a strategy for numerical investigation. The main part of the paper is the presentation and discussion of the simulation results, focusing on the lining deformation, load sharing and the safety margin of both linings. Interface stresses are also examined. It is found that significant secondary lining thickness reduction may be achieved by utilizing composite action. Challenges for the design of composite SCL tunnels are briefly discussed at the end. INTRODUCTION Sprayed concrete lined (SCL) tunnelling has seen rapid development over the last twenty years in the UK (Su 2013). One of these developments has been the replacement of traditional sheet membrane and cast in situ secondary lining with innovative spray applied waterproofing membrane and sprayed secondary lining system, which has been adopted in recent major projects, such as Crossrail (Pickett 2013), and brings many benefits to the construction (Dimmock et al. 2013). The combination of sprayed primary lining, spray applied waterproofing membrane and sprayed secondary lining is perceived to provide a structurally efficient lining system that outperforms the traditional lining system, which consists of sacrificial primary lining, sheet waterproofing membrane and cast in situ secondary lining. The claimed benefits in structural performance arises from the composite action between the sprayed primary and secondary linings via the spray applied waterproofing membrane, which produces a much stiffer cross-section and therefore a more efficient use of materials. Early investigations on the design of composite SCL tunnels were carried out without (1) definite and reliable long-term interface parameters, (2) a verified numerical modelling technique, or (3) consideration of different stress histories between primary and secondary linings (Thomas and Pickett 2011, Marcher et al. 2011). This paper reports the findings from a numerical parametric study on a typical composite SCL tunnel with varied secondary lining thickness. The results show that the true benefit of composite lining arises from the optimisation of the lining thickness (stiffness) ratio between the primary and secondary linings to achieve secondary lining safety and thickness efficiency at the same time."

Jan 1, 2016

By F. C. Bond

History The breaking and shaping of rock was one of man's earliest occupations. In the Paleolithic Age long before the dawn of history, arrow¬smiths and the makers of stone axes, hammers, knives, scrapers, spears, and borers were highly respected members of society. In early historical times stones for building blocks, roads, and city walls were shaped by slaves and convicts, who also did most of the mining. However, great artists erected beautiful stone sculptures, while gifted architects planned imposing temples and monuments. Until well into the 19th century nearly all rock was broken laboriously by hand. The small rock required by John MacAdam for his macadamized roads in England in the 1820s was produced by women and boys seated alongside the roadside with hand hammers and legs wrapped with rags. Eli Whitney Blake, a nephew of the Eli Whitney who invented the cotton gin, developed the first successful jaw crusher before 1870. The gyratory conical crusher soon followed. Comparative tests established its large capacity advantage over the jaw crusher, as well as its greater cost for a given feed size. Both types have been in use for more than 100 years. Crushing rolls appeared before 1900. Thomas A. Edison made very large diameter rolls which were excessively long; they failed because of shaft deflection. Various types of disk crushers and edge runner rolls appeared about this time. The older methods of reducing rock were adaptations of other processes. The stamp battery of dropping weights effected crushing by simulating heavy hammer blows; the much earlier arrastre, in which heavy stones were dragged in a circular path over the ore by animal power, came from the prehistoric method of grinding grain between two rubbing stones, while the jaw crusher was adapted from simple squeezing devices. But the tumbling grinding mill was not just an adaptation; it was an invention, because it required thinking on a somewhat higher order-there was no prototype. Its nearest antecedents were probably the small closed tumbling drums used in England more than a century ago for cleaning and polishing small iron castings. The date of the first tumbling mill actually used to grind rock is unknown, but it was later than the American Civil War (1861¬1865). It was almost certainly a closed or batch mill in which rock was placed and rotated until it reached the desired particle size. It could have been operated either wet or dry. The first published refer¬ence to such a batch mill was one introduced by Alsing in England (1870) for the grinding of calcined flints for pottery work.21 There are several rather indefinite reports of grinding mills in the early 1890s, including an overflow ball mill in the Helena and Livingstone reduction plant in Montana which may have been the first of its kind. 11 Many of the first mills, which were called tube mills, used hard rock both as grinding media and as mill lining. The rock used was preferably stone from the Normandy and Danish beaches, when it could be imported. This remarkable siliceous stone was already widely used for grist mills throughout America, and its resistance to wear was greatly respected. The decade of the 1890s saw the development of tumbling mills with continuous feed and discharge and their extension into different industrial uses. By 1895 some experience had been accumulated. Iron grinding balls were being tested and the proper speed of rotation was being determined. The Clark Patent tube mill was featured in an E. P. Allis bulletin of 1890, which may have been the first published description of a tube mill. More than 1,000 Gates tube mills had been built by Allis-Chalmers before 1913. Many of these were used in gold mining, espe¬cially in South Africa. The 5 x 22-ft size was particularly favored for grinding portland cement; the use of tumbling mills in the manufac¬ture of cement began about 1900. A great deal of attention was paid to the mill lining. Metal was then relatively expensive, and the general approach was to trap some of the rock grinding media into mill lining pockets. This rock would then absorb the wear and protect the metal lining. In the first ten years of the 20th century there were several different types of pocketed liners, with different manufacturers advancing the superior claims of their patented arrangements. The Osborne liner, developed in South Africa, was probably the most successful. 21 Another item which attracted much attention was size classifica¬tion within the mill and in ancillary equipment attached to the mill and rotating with it. The Krupp type, with interior screens protected inside the mill lining, was developed quite early in Germany, possibly before 1890. The Dorr reciprocating rake classifier (1907) had not yet been invented, and many strange and impractical screening and classifying devices were proposed. In these unsatisfactory machines the two separate processes of size reduction and classification were combined into one operation. It was many years before recognition came that a machine is most efficient when it is designed for one specific purpose. There was much industrial wastage before the opera¬tions of grinding and classification were finally separated. After 1900 the grinding of portland cement raw material and of cement clinker required large numbers of tumbling mills. Most of the raw material was then ground dry. This was also the heyday of gold mining. The old stamp mills that were used in great numbers for grinding gold ore did not grind sufficiently fine to liberate all of the gold, and the new tube mills were installed following the stamps. After 1910 larger diameter tum¬bling mills with larger grinding media were developed. These could receive the finely crushed ore directly, and the inefficient stamp batter¬ies were gradually eliminated. The Rand in South Africa was the greatest gold producer, treating immense quantities of rather low-grade but consistently free milling gold ore. The first tumbling mills, or tube mills, went into operation there in 1904. They were so successful that within a few years no new stamp batteries were installed in the district, even though old ones continued to pound away until after 1950.3 The early tube mills on the Rand all employed Normandy or Danish pebbles, which had to be imported at considerable expense. Their reported wear was as low as 4 lb per ton ground. 4 Many of the mills were lined with the same tough Danish stone cemented into place, while others used the pocketed steel Osborne liner. It was in 1907 on the Rand that an important test was made using hard native ore for grinding media in place of the expensive imported pebbles. 3 This ore, called banket, did not wear as well as the renowned Danish pebbles, but the cost per ton of grinding was definitely reduced. Many of the tube mills on the Rand were soon grinding with native ore. This was the beginning of the development now called autogenous grinding, in which the ore grinds itself. This is treated under a separate heading. See Subsection 3C, Chapter 4. Gold mining was important in America also, and its grinding history follows that of the Rand. Danish pebbles were replaced by native ore in Santa Gertrudis, Mexico, in 1913, 4 and in Consolidated Gold Fields, Nevada, in 1914. 5 Other properties followed suit. However, it gradually became apparent that the capacity of a given mill could be almost doubled if rock grinding media were re¬placed by cast iron or steel grinding balls. In order to increase plant grinding capacity many rock media mills were converted to iron grind¬ing media in the second decade of the present century. In some mills the motor size was doubled; other mills were cut in two and another motor was provided for the second half. Grinding mills began to assume a more modern appearance. Crushing rolls were formerly much used following crushing in jaw or gyratory crushers and preceding grinding in ball mills. How¬ever, the roll surfaces wore rapidly, and skilled maintenance was required to obtain even wear. Rod mills could take feed of the same crusher product size and reduce it finer. The first rod mill was con¬structed by Mine and Smelter Supply Co. and was tested in Canada

Jan 1, 1985

By F. Wolf, R. Ellmies

"Fluorspar is one of the most important industrial minerals. It has a wide range of applications, for example it is used in the steel and aluminum industry, and is also the raw material to produce hydrofluoric acid, Teflon or Gore-Tex. There are only a few major fluorspar mines worldwide, with China being the most important fluorspar producer (U.S. Geological Survey National Minerals Information Center, 2017). At Okorusu, Namibia, fluorspar has been mined with conventional open pit mining methods from 1955 until 2014 from a large scale metasomatic fluorspar deposit with seven identified orebodies. There are about 7 million tons of measured resources left with an average grade of 27.5 % CaF2. This paper is based at an MSc thesis at Technical University Freiberg and describes the design of an underground mine for the A and D orebodies with an annual production rate of 100,000 t acid-grade fluorspar product. By comparing different mining methods and adapting variants of access to the underground orebodies the paper will emphasize on the selection of a suitable mining technology, with a special focus on the economic considerations to decide about the most profitable operation. INTRODUCTION Mining holds an important part in the economy of Namibia. In 2016 11.1 % of the GDP was made through mining activities with 22 active mines (The Chamber of Mines of Namibia, 2016). Only one of them consists an underground mining operation. The global annual production of fluorspar is approximately 6 to 7 million t (U.S. Geological Survey National Minerals Information Center, 2017). Okorusu produced on average about 50.000 t annually in recent years (U.S. Geological Survey National Minerals In-formation Center, 2015). Okorusu Mine is Namibia’s only fluorspar mine. Fluorspar was mined in an open pit mine with four individual pits (A-D) since 1980. In 2014 the mine closed due to the increased stripping ratio and beneficiation problems. The mine assets were bought by Gecko Namibia. Currently Gecko uses parts of the processing plant for beneficiation of graphite from a neighboring mine. Figure 1 shows a panoramic view with the four pits and the mine village. The intent is to develop a concept for the further underground development of the mine. There are still about 7 million t of measured resources left in the deposit, with an average grade of 27.5 % CaF2. This study focusses on the underground mine design. The above-ground plant and facilities are considered as remaining unchanged."

Jan 1, 2018

By Günther M. Volkmann

"INTRODUCTION The construction of the BAB 44 motorway between Kassel and Herleshausen (both Germany) is an important part of the trans-European road network. After its completion, the A 44 will permit an efficient connection of the Benelux States in the West and Poland in the East. In the section between Eschenstruth and Hessisch Lichtenau the Hirschhagen Tunnel is constructed with a length of 4.1km. Most sections of the tunnel are situated in weak ground conditions. Hence a combination of face bolts with spiles (short forepoling) or pipe umbrellas (long forepoling) additionally support the tunnel heading on a regular basis This article will focus on the application of a newly developed method to connect the pipe umbrella support, which is mostly installed by conventional drilling machines nowadays. The installation method limits the outer diameter to a maximum of 168mm and a pipe wall thickness of 12.5mm because workers must be able to handle pipes and its drill steel. Typically these pipes are connected with threads that create a weak link in the support system so during the last decade alternative connection systems were developed to overcome this disadvantage. One of these alternative coupling systems is the so called Squeezed Connection, which will be explained in this article followed by a discussion of its advantages and disadvantages regarding technical specifications, construction time, and safety issues. THE HIRSCHHAGEN HIGHWAY TUNNEL The German highway A 44 directs from Aachen through the Ruhrgebiet to Kassel (all Germany) and it is extended to Herleshausen (Germany). The new section connects the A 7 to the A 4 after completion. This upgrades the east-west highway connection starting at the Benelux Union and heading to Poland so it is an important part of the trans-European road network. The newly constructed section has a total length of approximately 63 km and comprises 13 tunnels. All tunnels are constructed as double tube tunnels with 2 lanes and emergency sidewalks on both sides and 14 emergency cross passages. The Tunnel Hirschhagen starts in the north of Eschenstruth and ends near Hessisch Lichtenau (Figure 1). The length of the northern tube is 4,147 m and that one of the southern tube is 4,204 m. So it is the longest tunnel of the A 44 and the second longest highway tunnel in Germany when it is put into operation. On its alignment it crosses underground the Losse valley with the state road 7, the streetcar Kassel-Hessisch Lichtenau and the Losse stream. The cover above crown varies from 10 m to 95m and it is the lowest when crossing the Losse stream."

Jan 1, 2016

By Patricia Pride, Kurt Bettger, Jack Raymer

"INTRODUCTION The Jefferson Barracks Tunnel is in the final stages of design and is expected to go out to bid in the summer of 2016. The project is located in south St. Louis County along the west bank of the Mississippi River, about 13 km downstream of the St. Louis Gateway Arch. The project consists of a deep sanitary sewer tunnel, a deep pump station and several intakes. The intakes will divert sanitary flows into the tunnel and the tunnel will convey the flows by gravity to the Lemay No. 3 Pump Station, which will pump them up into the Lemay Waste Water Treatment Plant. The tunnel is about 5.4 km long and will be lined with 84-inch (2.1 m) fiberglass pipe. It drops at a gradient of 0.1 percent from south to north and will be bored through strong limestone using a hard-rock tunnel boring machine (TBM). The diameter of the TBM is anticipated to be about 3.4 m. The Owner’s original concept was for a relatively shallow tunnel so as to minimize construction and pumping costs. The preferred alignment ran close to the river, next to the existing force main, which was to be abandoned. Keeping the tunnel close to the force main would reduce the amount of shallow sewer work needed to connect the existing feeder sewers to the new tunnel. Several geotechnical investigations were performed, with shallowly focused geophysics and the borings all going exactly down the conceptual tunnel depth. Limestone bluffs run along the Missouri side of the river. These bluffs are pockmarked by sinkholes and riddled with karst. Large, well-known caves occur both north and south of the alignment. Karst features, including deep crevices and possible caves, were found in those early geotechnical investigations. Many of these features extended well below the level of the Mississippi River and would have been encountered by the tunnel. If a large crevice or cave were encountered, then the inflow of mud and water into the tunnel could have been large and possibly uncontrollable. Something had to be done to mitigate this situation. Pre-excavation grouting was considered, but the program would have been huge and extremely expensive. Using a closed-face TBM with bolted and gasketed lining was also considered, but that too was both risky and extremely expensive. The Owner could have abandoned the tunnel altogether and built a new force main, but that would have brought a whole new set of problems and was undesirable to the Owner. The last option was to move the tunnel away from the karst."

Jan 1, 2016

By Art Hamid, Manfred Wong, Carlos Jaramillo, Greg Raines, John Caulfield

"The Central Bayside System Improvement Project (CBSIP) is a critical element of the Sewer System Im-provement Program (SSIP), a 20-year, $6.9-billion investment by the San Francisco Public Utilities Commis-sion (SFPUC) to upgrade San Francisco’s 100+ years old seismically vulnerable combined sewer system. The CBSIP’s centerpiece, a proposed 10,000-foot-long (3,048-meter-long) Channel Tunnel, will provide reliable and redundant gravity conveyance and storage of combined wastewater flows from the northern and central parts of San Francisco to the Southeast Water Pollution Control Plant (SEP) while ensuring compliance with regulatory requirements for combined sewer discharges to the Bay. A tunnel with a diameter of 23 to 30 feet (7 to 9 meter) is being planned using pressurized-face tunnel boring machine technology. Project challenges include tunneling through Franciscan Bedrock, mixed ground conditions in close proximity to the Bay, connector tunnels and shafts, construction in congested urban environment, and challenging real estate issues for shaft access. BACKGROUND AND NEED FOR TUNNEL The City of San Francisco is one of the most beautiful cities in the world. About 850,000 people live in the city and many more come to work, for tourism, and for attending conferences. The SFPUC is a department of the City and County of San Francisco that provides energy, drinking water and wastewater services to San Francisco, wholesale water to three Bay Area counties, and green hydro-electrical and solar power to San Francisco municipal departments. The SFPUC wastewater system includes tunnels, large storage/transport boxes, 1000 miles of collection sewers, 28 pump stations, and three wastewater treatment plants. San Francisco’s combined sewer system collects both wastewater and stormwater in the same sewers, which is then pumped, treated to stringent state standards and discharged into the San Francisco Bay and Pacific Ocean. After decades of service, much of the sewer system is nearing end of its working life. During the 1989 Loma Prieta earthquake, damage to SFPUC water and wastewater infrastructure was extensive. The 11,200-foot-long (3,400-meter-long), 66-inch-diameter (1,676-mm-diameter) Channel Force Main, built in 1976, and a critical component of the SF wastewater system was also damaged. This force main carries 70 percent of the bayside dry weather sewage flow from the northern and central part of the city to the SEP. The force main is at the end of its life and was not constructed to the current seismic code; in addition it has no redundancy. Figure 1 shows the project background and the force main that will be provided redundancy by the new gravity tunnel."

Jan 1, 2016

Acid mine drainage (AMD) forms when sulfide minerals are exposed to oxidizing conditions in coal and metal mining, highway construction, and other large-scale excavations. Iron sulfides common in coal regions are predominately pyrite and marcasite (FeS2), but other metals may be complexed with sulfides forming chalcopyrite (CuFeS2), covellite (CuS), galena (PbS), and sphalerite (ZnS). Pyrite commonly occurs with these other metal sulfides thereby causing AMD where Cu, Pb, and Zn are mined. Upon exposure to water and oxygen, sulfide minerals oxidize to form acidic, sulfate-rich drainage. Metal concentrations in AMD depend on the type and quantity of sulfide minerals present. The drainage quality emanating from underground mines or backfills of surface mines is dependent on the acid-producing (sulfide) and alkaline (carbonate) minerals contained in the disturbed rock. In general, sulfide-rich and carbonate-poor materials produce acidic drainage. In contrast, alkaline-rich materials, even with significant sulfide concentrations, often produce alkaline conditions in water. Approximately 20,000 km of streams and rivers in the United States are degraded by AMD. About 90% of the AMD reaching streams originates in abandoned surface and deep mines. Since no company or individual claims responsibility for reclaiming abandoned mine lands (AML), no treatment of the AMD occurs and continual contamination of surface and groundwater resources results. The oxidation of iron disulfides and the generation of acidity occur through several reactions (Stumm and Morgan, 1970). The chemical equations can be found in Caruccio and Geidel (2000). If any of the processes represented by the equations were slowed or altogether stopped, the generation of AMD would also slow or cease. The equations show that 1000 Mg of rock containing 1% sulfur, all as pyrite, would yield upon complete reaction 31.25 Mg of acidity. Therefore, 31.25 Mg of 100% CaCO3 would be required to neutralize the acidity. The alkaline content of overburden determines whether there is enough neutralization potential (NP) to counteract the acid produced from pyrite oxidation. Of the many types of alkaline compounds present in rocks, only carbonates and clays occur in sufficient quantity to effectively neutalize AMD. A balance between the acid-producing potential and neutralizing capacity of an overburden sample will indicate the ultimate acidity or alkalinity that might be expected in the material upon complete weathering. Accurate prediction and control of AMD before surface mining require an understanding of three important factors: 1) overburden geochemistry, 2) method and precision of overburden handling and placement in the backfill during reclamation, and 3) the postmining hydrology of the site.

Jan 1, 2002

By D. M. Milne, H. H. Kanduth

INTRODUCTION The past few years has seen an increased interest in the determination of statistically valid properties of a rock mass. The increased use of computer modelling for the study of rock excavation behaviour has created a need for upper and lower statistical bounds for the properties of a rock mass being modelled. Obviously, to determine the statistical properties of a large volume of rock, many samples must be tested - an expensive proposition when using conventional testing facilities and procedures. As a result of high costs per sample, sufficient tests for statistically valid results are rarely done. In an effort to reduce both sample preparation and test facility costs, an instrument called the Bemek Advanced Rock Tester (BRT) was developed in Sweden. With a total weight of approx. 35 kg, the BRT is portable and sells at a small fraction of the cost of a conventional testing machine. It is comprised of a small 65 KN loading frame with attachments for a variety of tests (see Table 1) , a hand operated hydraulic pump, an electronic balancing unit and a programmable microprocessor. The microprocessor is capable of storing data, performing arithmetic operation on, and printing signals from, a transducer and two strain gauges. A detailed description of the apparatus is given by G. Swan et al. (1). The proposed test strategy involves first a 3-point flexure test on a notched core specimen, followed by a 4-point flexure test on the separated specimen halves. Finally, point load and Brazilian tests can be carried out on the quarter parts of the original specimen. Thus specimen preparation is kept to a minimum. These and other perceived advantages have prompted the purchase of this machine and an evaluation of its suitability to provide data on mechanical properties of intact rock for numerical modelling and rock mechanics design at Noranda's underground mines. Details of its performance evaluation and experiences with the unit are discussed in the following sections. [ ] INITIAL OPERATING EXPERIENCE During the commissioning stage the BRT had, or developed, a series of problems, some of which seriously affected its operation. Below are some examples. Poor documentation was the most serious problem encountered. Confusing instructions for the 4-point bend test installation and its microprocessor programing, as well as poor and ambiguous information on the calculation of gauge factors, are some of the difficulties which had to be overcome. Meehan~cal problems occurred, including failure of the hydraulic pump, as well as electronic difficulties with the microprocessor. Other problems with the printer, requiring its replaceqent, were fortunately covered under warranty.

Jan 1, 1986