Search Documents

By G. B. Misra

Though installations of main mine fans vary widely, the commonest installation is of a surface exhaust fan connected to an upcast shaft some distance below its collar by a horizontal fan drift bending sharply. downwards near its junction with the shaft. The junction of the fan drift with the shaft often causes considerable shock pressure loss if not properly designed. In one of the major coal mines in India circulating 180 m3/s of air through the mine a pressure drop of 229 Pa out of the total fan pressure of 568 Pa occurred at this junction while in a smaller gold mine circulating 9.4 m3/s it was 147 Pa out of a fan-drift pressure of 382 Pa. With larger mines circulating larger volumes of air, ill designed fan drifts can lead to considerable wastage of the power of ventilation. Shock loss at the junction of fan drifts with exhaust shafts depends on (1) the angle of deflection of the bend, (2) sharpness of the corners (both inner and outer) at the junction, (3) the degree of contraction of the flow-stream which depends on the cross- sectional area ratio of the shaft and the fan drift as well as the amount of leakage through the shaft collar. It must be noted here that the friction pressure loss in the bend is negligible compared to the shock pressure loss.

Jan 1, 1980

By Changwoo Lee

Under drastically deteriorated situations, diesel equipment was introduced to some of local coal mines, aiming at higher productivity and better safety. To accommodate various diesel equipment in conventionally developed mines, mining system itself had to be modified; much larger trackless haulage ways were excavated. Possible health hazards of diesel not taken into account at the beginning become a serious concern and effective control measures are being searched for. The purpose of this paper is to study the diffusion characteristics of diesel exhaust in local coal mines. One of the parameters affecting dispersion of diesel contaminants is the coefficient of turbulent diffusion. Since CO2 is known to be closely correlated with other contaminants such as CO, NO, NQ, SO2 and RCD, it was chosen as a tracer gas in a series of dispersion experiments. A large diesel passage as well as a conventional track haulage way were the sites for the experiments. Rectangular dispersion pulses were generated for 30 ~60 seconds and CO2 concentrations were recorded at several locations 50~190 m downwind. The diffusion coefficients calculated graphically vary between 0.10~0.48 m2/s at both haulage ways. The results are analyzed to find any correlation with the air velocity and the distance from the disperser. Skobunov's empirical formula is applied to the experimental data for comparison and the relationship between Reynolds number and Ex/Dp/sci0.4 Sc1…

Jan 1, 1995

By Ted M. Noskiewicz, James A. Ramsay

INTRODUCTION During the various stages of an underground project from inception through design and construction, probably the single factor of most interest and concern is the nature of the ground. The ground conditions more than any other item govern costs and feasibility; and although the methods available for assessing the ground have become increasingly reliable during the past thirty years, it is still very difficult in many cases to predict the behaviour of soil and rock during and after excavation. To help in this ground evaluation process, we have frequently supplemented the boring program with one or more large diameter inspection holes; and during the past eighteen years, seventeen of these holes have been constructed on tunnel projects which we have designed. There are references in the literature to similar inspection holes (1); however, as far as we are aware, no detailed description of them has been published. The behaviour of soil or rock during and after excavation and the effect of ground water on tunneling operations are of vital interest to tunnel designers and contractors. A comprehensive geotechnical investigation is therefore among the early and most important tasks carried out on a tunnel project and the backbone of every geotechnical investigation is the boring program. A series of borings, typically 50 to 100 mm (21 to 4 in) diameter, are drilled from which soil samples or rock core are recovered and the ground water observed.

Jan 1, 1979

By John W. Graham

To start my talk, I thought it might be helpful for us to define the term "aggregate", so I went to the dictionary. Webster has several listings under "aggregate", and I found the following: "1. A mass or body of units or parts somewhat loosely associated with one another." Well, I didn't like that term "loosely" so I read on. "2. Crystals of one or more kinds of mineral or rock fragments." That sounded better, but I still read on. "3. Any of several hard inert materials used for mixing with a cementing material to form concrete or mortar." That sounded even better, but it should be a little broader. So I would like to define "aggregates" for you as follows: "Hard, inert fragments of rock or minerals used alone or with cementing agents to form products essential to nearly all types of construction." Usually aggregates are sand, gravel, or crushed stone, but other minerals such as clay or shale can be heated and become aggregates. What are some of the construction uses? Well, we've already mentioned concrete, as used in streets and highways, sidewalks and parking lots, airports and all kinds of building construction, not to mention bridges and swimming pools, and docks and breakwaters, just to list some of the uses. Our way of life couldn't exist without concrete. And you can't have concrete without aggregates,

Jan 1, 1977

By M. Yavuz

Decision Making (DM) can be defined as a selection process of the best one among the alternatives sets in order to obtain goal, and mostly has an uncertain situation [7]. Every mining engineer is subjected to a number of mining DM problems in daily mining operations. In reality, all stages of mining have its own DM problems. Most of time, engineers do not use scientific methods for DM problems. These problems can mostly be solved by the engineers according to their past experiences and practical studies. Mining engineers often use their intuition in DM process. Experience and intuition have been central to DM because of the frequent lack of quantitative data including geology, grade distribution and ground condition, as well as environmental, social and economic factors [8]. In decision process, linguistic variables become in question and decision makers may not know how these variables are computed [9]. So, the DM process may be qualitative, quantitative or combination of the two. The problem structuring and analysis process is conceptualized in Figure 1 [8]. The qualitative analysis is based primarily on the judgment, knowledge and experience of an expert (or team of experts). In a quantitative analysis, the focus is on facts and the data associated with a problem and a mathematical formulation that encompasses the objectives, variables and constraints of the particular problem. The quantitative analysis has traditionally been the subject of operation research and management science [8].

Jan 1, 2008

By G. Markopoulos

Every year thousands of people from all over the world come to Mount Parnasse, visiting Delphi, the Parnasse ski-resort and other sights in the area of Fokida, available to all ages all year round. This region of Greece, is not only gifted with natural beauty, but also with valuable underground natural wealth: inside Mount Parnasse and the adjoining Ghiona Mountain, there are rich bauxite deposits - the ore from which aluminium is made. In this magnificent part of our country, any mining activities undertaken must be adapted to coexist within such an ecologically sensitive area. This demands an enormous effort, knowledge and the use of technology. This is definitely our Company's primary objective. Our company's (Silver & Baryte Ores Mining Co. S.A.) activities in the area began in 1933, when Euripides Mavrommatis and the two Eliopoulos brothers, Elias and George, established "Bauxite Parnasse SA". Since then, ten thousand people have worked in these ore deposits, and 45 million tons of bauxite have been extracted. The full length of the underground excavations is more than 300 kilometers and 115 million cubic meters of limestone have been extracted on surface mining. In 1996, Bauxite Parnasse merged with Silver & Baryte Ores Mining Co. S.A. Now, the company exports more than 1.500.000 mt per year of bauxite to more than 15 countries around the world, offers a significant amount of job opportunities in the region, and imports valuable exchange into the country.

Jan 1, 2002

By William C. Paschen

Damen Avenue to Roosevelt Road, the Tunnel and Reservoir Plan (TARP), a Deep Tunnel Project for the Metropolitan Sanitary District of Greater Chicago consists of 25,189 lin. ft. of 32 ft. tunnel with 1 ft. 0 in. concrete liner throughout. The 17,100 ft. main tunnel connects at both ends with two other Deep Tunnel contracts. A branch tunnel connecting to the mainstream tunnel, commences approximately 4,140 ft. from the construction shaft and runs 8,089 ft. south and terminates at the Racine Avenue Pumping Station. Shaft work consists of one 28 ft. 6 in. diameter construction shaft, one 3 ft. 6 in. diameter access shaft and 25 drop shafts-four of which have vent shafts. The drop shafts vary in diameter from 4 ft. 0 in. to 17 ft. 0 in. All shafts vary in depth to invert from 225 ft. to 235 ft. Work has been underway for 16 months and as of this writing the construction shaft and access shaft are complete. Seven shafts have been excavated and concreting operations have started in four of them. The starter tunnel is complete, the mining machine has mined 250 lin. ft. and the muck removal system is in full operation. The contractor for the project is a joint venture of Paschen/Morrison-Knudsen/Kenny. Paschen Contractors, Inc., Chicago, Illinois is the sponsor. The total contract amount is $107,837,300.00.

Jan 1, 1979

By N. S. P. Kumar

INTRODUCTION Development work at Carr Fork Mine of Anaconda Copper Company in Tooele, Utah commenced in August 1974. A decision to install an underground gyratory crusher for primary crushing run-of-mine ore and waste was made in 1976. Higher throughput rates, larger reduction ratios and greater flexibility in terms of meeting immediate and expanded production needs were the main reasons for selecting the gyratory crusher over the jaw crusher. UNDERGROUND MATERIALS HANDLING Underground crushing and conveying system was designed for a capacity of 16,300 mtpd of ore and waste on a 2-shift, 5-day week basis. Engineering and design of crusher complex was performed by Anaconda engineers at Carr Fork. Figure 1 represents the longitudinal section of mine showing the general materials handling system. Mine area is trackless except for materials and production haulage which is run on rail track on both 1200 and 970 levels. Ore from stopes and waste rock from development headings are handled by 3.8 cu m (5 cu yd) Jarco scoops and dumped into 2.4 m (8 ft) diameter ore and waste passes at the 1200 level. The material gravitates down to the 970 level where it is loaded into 12 cu m (420 cu ft) ASEA mine cars using side loading chutes. The muck train, consisting of 15 to 18 cars and two 27 mt General Electric trolley locomotives, is hauled over a distance of 2,300 m (7,550 ft) to

Jan 1, 1981

By Reid Trent, Jon C. Volkwein

The U.S. Bureau of Mines is investigating a novel technique to control methane in underground mines by using methane oxidizing microorganisms termed methanotrophs. Coalbed methane has been responsible for many mine disasters and will continue to be a safety obstacle to mining deeper coal seams. Deeper seams of coal contain more methane gas, and better strategies for removing the methane will need to be developed. Methanotrophic microorganisms offer a novel alternative since they physically remove the methane, are commonly found in soils, and already have been found to exist in many foreign coal mines. Proposed applications of this concept include the inertization of buffer zones separating active mining areas from sealed gobs, reducing ventilation from ventilated gobs and reducing methane content from longwall gobs. Current work includes an assessment of the abundance of naturally occurring methanotrophs in U.S. mines, testing the amount of methane that various types of microorganisms can consume, studying the effects or use of the byproduct gases, and finally developing practical appl ications of this biotechnology to coal mining. This paper reports on the initial laboratory testing that measured the quantity of methane consumed by two types of methanotrophic microorganisms. Average rates of methane consumption were between 1 and 4 ml/hour in column flow tests. A possible gob application may require that 750 cfm of methane be consumed during periods of maximum outgassing. It is premature at this time to accurately scale from laboratory to mine application.

Jan 1, 1991

By J. Köppel, K. Kovári, Ch. Amstad

INTRODUCTION The measurement of displacements in soil or rock in the vicinity of underground openings provide valuable information for a better understanding of the behaviour of the structure. On the basis of systematic observations conclusions can be drawn concerning - safety of the opening in the various stages of excavation - effectiveness of the support measures - nature of the rock pressure to be expected - influence of the construction of the opening on neighbouring structures (settlements of foundations, underpassing other tunnels etc.) - comparison of theoretical predictions with the actual structural behaviour (1). Today there are several types of suitable instruments available that can be employed at reasonable costs for such investigations (2). The most important ones are the multiple point borehole extensometer, the inclinometer and the multiple point borehole deflectometer. As is well-known, the extensometer only measures the displacement component in the borehole axis, while the inclinometer and the deflectometer provide monitoring of rock mass movements normal to the borehole axis. In the following a new instrument is described, which has been given the name Extenso-Deflectometer ISETH. In this single piece of equipment certain features of the above-mentioned three types of borehole instruments are incorporated. it enables the measurement of all three components of the displacement vector at consecutive points along the borehole, the axis of which may have any direction in space. This device is portable like the inclinometer. A simplified version

Jan 1, 1979

By G. F. Friel, G. S. Morrow, J. C. Edwards

An experimental program in the U.S. Bureau of Mines' Safety Research Coal Mine evaluated the effects of dead end crosscuts on the transport time of CO along a mine entry. The presence of carbon monoxide is a characteristic of a fire in its incipient stage, and is significant in the determination of a fire location in a mine from the analysis of arrival times of pre-set concentrations at CO monitors. In this investigation two entries, with a total of ten crosscuts, connected by a room were instrumented with CO sensors as part of a real-time monitoring and data acquisition system. Controlled release of 1% CO was monitored as the contaminant traveled the entries for several different configurations of CO sensors and exhaust fan settings. In addition to the normal longitudinal dispersion of CO due to turbulent mixing at the front of the CO wave, the induced rotation of air established within a crosscut by the entry flow diluted the CO concentration through entrainment. It was determined experimentally for the entry and crosscut configuration considered that the transport time for a specified CO concentration was 27% greater than the predicted time based upon entry volume only, but 13% less than the predicted time based upon entry and total crosscut volume. The proper interpretation of the measured transport time of a specified contaminant concentration between sensors is important for mine safety in the isolation of a fire and plans for miner evacuation.

Jan 1, 1993

By Jeffrey P. Carstens

INTRODUCTION Thermally induced fracture of rock is one of the oldest rock breakage techniques known to man. Primitive underground miners used fires to heat and crack rocks as early as the third century B.C. (Ref. 1). History aside, however, present-day tunneling and mining interests are reconsidering the use of modern heating units for rock fracture for some very good reasons. One of the most important advantages of many heating techniques is the lack of direct contact between the heating device and the rock. This means a lower wear rate relative to mechanical cutters, and no large reactant force to be supplied by the tunneling machine. In addition to avoiding physical contact, some heating systems (e.g., electron-beam guns and lasers) can deliver energy to a rock face much more intensely than can be conveniently handled mechanically. Thus, heating power densities of the order of lob to 107 watts/in.2 and greater can be achieved with high-power lasers. These high power levels allow much higher instantaneous penetration rates than can be achieved by mechanical cutting. Another advantage that accrues to some thermal techniques, such as, for example, surface spalling, is that the thermal fracture process works particularly well in certain rock types (e.g., granite) that are particularly hard to cut mechanically. Other methods, involving high power density, are able to cut any rock type, and are relatively

Jan 1, 1997

By Arnaud Colson

1 Good morning ladies and gentlemen. Let me first thank you for welcoming me to this international congress. I?ll have the pleasure to explain to you how the Lafarge group works on its quarry rehabilitation. I will deal with the way quarry rehabilitation has affected all branches of the group trough a global approach. 2 Quarries often are a subject of controversy dividing those are for and those who are against. My purpose is rather to examine where factors of progress lay and how in a quarry such as Lafarge we can include quarry rehabilitation, which is so fundamental dimension of our process. 3 - 4 As these two photos of French quarry show taking into account the environment in the quarry industry has been a recent preoccupation. In less than a century rehabilitation has a dramatically evolved in a positive way. Consequently our group integrate an ecological dimension in its activity. It?s an ethical question as well as a personal view of our role as a responsible industrial group. 5 My presentation is built around 4 points: I?ll begin by explaining why it?s our responsibility to rehabilitate quarries. I?ll go on to fill you in on the method of the project. After that I?ll outline the expected results. Finally I?ll talk about the rest of the project and the way we can ensure this know how.

Jan 1, 2002

By John A. Lombardi

The HW Process Technologies Engineered Membrane Separation (EMS"') technology is a patented system for the removal of multivalent base metal cyanide complexes from cyanide process streams, and EMSni permeate, concentrate and recovery terminology is explained. Specifically, use of the EMS™ system for the removal of Cu(CN)i- and Cu(CN)43- cop­per from cyanide process streams is discussed. The historical "Copper-Gold" processing paradigm of copper related cyanide consumption and complexation and methods to recover copper and copper complexed cyanide from Cu-Au process solutions are summarized. An advanced stage R&D sequential Cu-Au leaching circuit is proposed wherein two PLS streams are generated, i.e., a high copper tenor "first flush" Cu-PLS and low Cu tenor "second flush" Au-PLS. Copper and cyanide recovery from the EMS"' concentrate generated by Cu-PLS EMSTI,f processing by well known acidification processes and lesser developed, but techni­cally feasible, electrowinning processes are projected to be lower cost than similar dilute solution treatments. Gold is described as Merrill-Crowe plant recoverable from the EMS™ permeate stream coming from the Cu-PLS EMS"' process. Gold is also recovered from the EMSTI,f permeate generated by the processing of an Au-PLS bleedstream. The economics of the proposed Cu-Au-EMS"' circuits are estimated as $2/ gpd capital cost for large systems and $1- $3/ l 000 gallons treated operating cost plus royalty.

Jan 1, 1998

By Mark Godfrey, Wickus Slabbert, Debra Miller, Dave Dew

Sao Bento Mlnerai;;ao Mine (SBM), located 100 kms northwest of Belo Horlzante, Brazil, was commissioned In 1987t1l to produce 185 kg per month of gold from 240 tpd of refractory sulphide flotation concentrate. The concentrate Is processed by a Sherrill Gordon design pressure oxidation circuit followed by conventional CIL gold recovery process (Flgur .. J). The original plant design foresaw expansion to 480 tpd, and In this regard the acidic effluent neutralisation, CIL and carbon circuits were designed for future expansion to treat the higher tonnage. The pressure oxidation section was sized for 240 tpd with the Intention to double the Installed plant equipment to provide 480 tpd capacity when required. This decision was based In part on the novelty of pressure oxidation to treat refractory sulphide concentrates in 1984 when the process design was finalised. General Mining, Metals & Minerals (Pty) Ltd (GENMIN), has been actively Involved for the past 30 years in the development of bacterial process for the oxidation of refractory gold concentrates; the results of this development program have provided the registered process BIOx®. The successful Implementation of BIOx® technology for treatment of refractory gold concentrates at GENMIN's Fairview Mine In October 1986t2l, as well as the substantial experience accumulated in laboratory and pilot testing of some 40 other sulphide concentrates, Justified reconsideration of the oxidation process best suited to provide the Incremental sulphide oxidation capacity planned for SBM.

Jan 1, 1992

By John Wiebmer

Six industry trends will have significant effect on the way mining equipment is designed and supported in the years ahead: 1. MINING IS MIGRATING TO LESSER DEVELOPED PARTS OF THE WORLD The global recession of the early 1980's drove down commodity prices and intensified cost competition. This caused a fairly dramatic trend in mining away from higher cost operations in developed countries to richer, lower cost deposits in developing countries. Miners operating in lesser developed parts of the world will place higher value on rugged, durable designs that can live in more difficult and sometimes abusive conditions. They need engines and power train systems that are more tolerant of a wide variation in fuel quality and oil specifications. They'll require machines that are simpler to operate, simpler to maintain, simpler to troubleshoot and simpler to repair. And they'll require creative means of support in getting technical information, parts and components to remote operational sites. Mining equipment in the future will be more durable and simple than it is today, and product support will grow in importance as purchasing criterion. 2. THE MINING INDUSTRY IS CONSOLIDATING An intense amount of corporate acquisition and industry consolidation activity is occurring, to the point that today just 50 mining companies account for 55% of the western world non-fuel mineral production. Consolidation will continue, leading in the future to an industry structure weighted heavily toward a few key global mining houses.

Jan 1, 1993

By Peter Kowalczyk

The acquisition of submarine gravity data using airborne gravity technology is a practical reality. Ocean Floor Geophysics plans to deploy a free-swimming ROV based submarine gravimeter on a commercial basis in early 2009. The submarine instrument is a variant of the well-used GT-1A airborne gravimeter. Airborne gravity surveys are now routine. The primary factor controlling the accuracy of airborne gravimeters is the precision of the GPS measurement of vertical movement of the sensor platform. The gravity measurements along a flight line are the differences between the output of the gravimeter vertical accelerometer and the estimate of the aircraft vertical acceleration using the differential GPS system. The principle difficulty of moving an airborne gravimeter to a free-swimming submarine platform is the necessity to have an accurate real time estimate of the changing elevation and hence changing vertical acceleration of the platform; GPS doesn't work underwater and an accurate estimate of depth fluctuations to the necessary precision is difficult to acquire. It is interesting that the airborne gravity gradiometer technology, which competes with the airborne gravity technology, was first developed as a classified military application for use by missile submarines during the cold war. Gradiometers were developed for this application specifically to avoid this problem. A gradiometer does not require as accurate an estimate of its vertical position to make a useful reading- it measures gravity gradients, not the gravity field itself.

Jan 1, 2008

By Robert B. Hopler

For many years the explosives industry was a technological enigma: it was at the 'cutting edge' of some technologies and in the backwaters of others. For example, for at least the past 85 years, the industry routinely measured time to one-millionth of a second for determining the detonation rate of explosives. At the same time, however, formulations were usually hand-written in 'formula books,' such as the alchemists may have done. Also, due to the fact that the equipment had proven to be safe, many of the mixers and packing machines in use until recently were those patented in the 19th century; improving efficiency was not worth the possible risks that might be encountered. In recent years, the wide availability and portability of computers and their adaptation to specialized applications have revolutionized the explosives industry, much as it has many others. With the advent of the water-based emulsions and slurries (water gels), and the necessity to design totally new processing and delivery equipment, the opportunity arose to apply modern techniques to many aspects of the business. Table 1 lists some computer applications currently in use by explosives manufacturers and end users. The use of high-tech production controls, equipment design aids, field measurement devices and other computer applications is so pervasive in the industry today that any brief article such as this must be considered only as a broadbrush overview of the subject.

Jan 1, 1994

By Dale A. Bivens

INTRODUCTION The Waste Isolation Pilot Plant (WIPP) is currently being constructed for the United States Department of Energy in SE New Mexico. The purpose of the project is to store low level transuranic waste in an underground environment which will ensure a safe atmosphere for the life of the stored waste. Ohbayashi was contracted by the DOE to sink two shafts and underground drift development which will be used to conduct a series of long term experiments in order to finalize the suitability of the geology and the environment for the transuranic waste storage. The two shafts sunk at the WIPP site were excavated around a borehole by conventional methods. The excavation around a borehole eliminates some of the established blind bottom sinking techniques, but creates unusual problems which must be pre-planned and scrutinized closely. An analysis of the slashing to the borehole technique will be given. WASTE SHAFT The waste shaft (w/s) is 5.8 meters (19 feet) in diameter and will be used primarily to transport the radioactive waste to the underground storage area. A pre-existing 1.83 meter (6 feet) diam borehole was taken to a depth of 655 meters (2150 feet) to the existing drift; at this level, a 38 meter (125 feet) sump was installed using blind bottom sinking techniques. Geology The primary geology for the w/s excavation is redbeds, anhydrites, dolomite, mudstone and

Jan 1, 1985

By M. Makarenko

The sandstone type Devladivske uranium deposit is located within the limits of Eocene pale-ovalley filled with alluvial sediments. Mineralization with uranium content up to 0.1% forms several ore beds divided by redox barriers. In the period 1962-1983 the deposit has been exploited over an area of 918000m2 by in situ leaching (ISL) using drillholes with a depth between 35 and 100m. During mining operation about 200,000 t of H2SO4, 6,300 t of HNO3, and 15,000 t of NH4NO3, have been pumped in the ore body. In 1983, the groundwater pollution aureole had a length of 4.5 km and a width of 400-600 m. There is a hydraulic connection between the uranium-bearing aquifer and both the upper and lower ones. The technological solutions used for ISL caused partial contamination of these horizons. After mining completion, dilution of the residual technological solutions with "pure" natural waters took place through gaps in impermeable sediments between aquifer horizons. Calculation of self-purification process kinetics shows that the sulfate ion pollution aureole will disappear approximately after 120-150 years at a distance up to 2.0-2.5 km from the western margin of the deposit. This means that there is no risk for contamination of the river Saksagan? that flows at a distance of 17km from the deposit.

Jan 1, 2005