Search Documents

By R. Parada

A real-time dynamic simulation model has been developed to characterise the flash furnace operation at the Chagres smelter. This model permits the operators to plan the process to meet the Peirce Smith converters' schedules and feed the acid plant with gases that satisfy its best operating efficiency range. Essential control parameters for the furnace (process air enrichment, oxygen coefficient and supplementary heat) are calculated to satisfy process targets such as matte grade, slag silica and matte/slag temperatures. These calculations are carried out with a real-time simulation. Flash furnace control and operational stability permits setting up control strategies that streamline the flow of copper to converters and of sulphur to the acid plant.

Jan 1, 1999

By Eun Duck Park

The gold catalyst supported on iron oxide was prepared from gold dissolved in aqua regia by a deposition-precipitation method and applied to CO oxidation in the absence and presence of hydrogen. Some characterization methods such as X-ray diffraction (XRD), nitrogen adsorption, transmission electron microscopy (TEM), temperature programmed reduction (TPR), temperature programmed oxidation (TPO), and the pulsed CO chemisorption with temperature programmed desorption (TPD) were conducted to explain different catalytic activities of Au/Fe2O3 catalyst pretreated at different conditions. The particle size of gold was about 10 nm for Au/Fe2O3 calcined in air at 373 and 573 K. For complete CO oxidation, the decreasing CO conversion with a reaction time was observed at low temperatures but its initial catalytic activity can be restored by a heat treatment at high temperatures. This catalyst was quite active for the selective CO oxidation in the presence of hydrogen especially at low temperatures. In the presence of hydrogen, the deactivation was significantly diminished.

Jan 1, 2006

By Takao Mori

Novel rare earth boron icosahedral compounds are investigated as potential high temperature thermoelectric materials. REB50-type compounds and REB22C2N compounds were synthesized and the thermoelectric properties measured. Seebeck coefficients in excess of 200 V/K are observed at temperatures above 1000 K for the REB50-type compounds. Strikingly, n-type behavior was observed for REB22C2N. Up to now, non-doped B12 icosahedral compounds have all been p-type. The discovery of an n-type compound is extremely important in terms of the potential development of this class of compounds as viable thermoelectric materials. Low thermal conductivities of < 0.03 W/cm/K at room temperature was observed for these rare earth boron cluster compounds.

Jan 1, 2006

By V. Bhagavathy

This paper describes a method for the determination of traces of rare earths using energy dispersive x-ray fluorescence spectrometry (EDXRF) after preconcentration of their oxine complexes onto activated carbon. Various parameters that influence adsorptive preconcentration of rare earths onto activated carbon viz. pH, amounts of activated carbon and oxine, time of stirring and aqueous phase volume were systematically studied. A numerical method based on simple least square procedure using fifth order polynomial with 25 consecutive values was developed for smoothing and differentiation of EDXRF data which was previously digitized and averaged. First order derivative EDXRF in conjunction with adsorptive preconcentration on activated carbon enables to determine as low as 10 ppb of each of individual rare earth elements.

Jan 1, 1989

The present work is mainly focused on developing intermetallic inert anodes for aluminum electrolysis. The anode alloy based on Al-Ti-Cu system was prepared by casting, followed by the application of a protective coating. Behaviour of corrosion and the passivation under anodic condition was characterized using the electrochemical and microscopic techniques. The results obtained clearly demonstrate that the oxide coating can provide good corrosion resistance via surface passivation of alloy anodes, rendering them inert in cryolite melt.

Jan 1, 2006

By Erik Olsson, Gunilla Hyllander, Stefan Schuster, Lena Sundqvist Ökvist, Maria Lundgren, Michael Hensmann, Olavi Antila

"Residual materials from the integrated steel plant itself or other sources often contain valuable compounds of e.g. C and Fe. Dust and sludge have to be agglomerated to be able to recycle to the blast furnace (BF) via top-charging. By injection of the materials, preparation methods in terms of e.g. drying and/or screening only, can be used. Alternative carbon materials (ACM) in terms of BF dust and sludge have been successfully injected up to levels of 60 kg/tHM in the LK.AB Experimental Blast Furnace (LKAB EBF®). Efficiency in recovery of valuable compounds as well as the behavior of undesired elements have been evaluated and are discussed.IntroductionTraditionally, recycling of steel in-plant fines is made via the sinter plant and blast furnace route. Steel plants operating with 100% pellet as ferrous burden and have no sinter plant. There are limited areas for land fill and costs are caused for preparation of landfills and deposit fees. Very fine paniculate dusts or sludges cause decreased productivity and increased coke rate in the sinter plant, and therefore other ways for recycling must be considered. Injecting them into the BF could be an economically and technically feasible alternative. Additionally, as the materials contain valuable compounds of e.g. C and Fe."

Jan 1, 2012

By Luciano B. Oliveira, Luis G. C. Marques, Sergio N. Monteiro, Marcos V. M. Fagundes

"Biodiesel production is normally associated with large plantations of oily vegetables such as soybean and colza, in large rural areas. However, in the municipal limits of the city of Rio de Janeiro, southeast of Brazil, biodiesel is being produced from wastes commonly generated by typical urban activities such as sewage sludge, discarded fat from meat markets and post-used cooking oils. In the present work, the experience of producing biodiesel from urban wastes in Rio de Janeiro is assessed. The type of precursor materials, equipments and logistics are presented. The environmental and economical advantages as well as the drawbacks are discussed.IntroductionThe interest for a liquid fuel that could substitute those obtained from petroleum started more than one hundred years ago when Rudolph Diesel tested his no-spark internal combustion engine, impelled by compression, with peanut oil. By that time, petroleum was beginning to be extracted in large scale and no one was concerned with the future environmental problems and its eventual depletion. In the last century, the successful association of petroleum based fuels with the automotive industry was an almost insurmountable obstacle to any attempt to use nonmineral oils [1]. In addition to the greater efficiency and, by then, lower price of the diesel from petroleum, the use of plain vegetable oils introduced undesirable carbon deposits and reduced the engine lifetime. Today, the situation is reverse. The continuous increase in the price of petroleum and, above all, its contribution to climate changes are strongly motivating the use of biofuels to replace those obtained from fossil fuels such as petroleum, natural gas and coal [2].In the case of the common petroleum derived diesel, many countries are now engaged in large scale substitution programs. The USA should produce more than 700 million litters of biodiesel, while the European Community is expected too produce around 6.5 billion litters in 2008. In Brazil, the federal biodiesel program imposed a minimum of 2% addition to the common diesel. This would demand a production of 800 million litters in 2008 [3]. The Brazilian biodiesel is made from a diversified source of vegetables mainly castor bean, African palm and soybean. The main producers are agrobusiness firms located in large rural areas of the Brazilian hinterland [4]."

Jan 1, 2008

By Maurizio Marezio Bertini

Successful treatment of contaminated sediments was achieved by sparging either 0.5 M NaOH solutions or distilled water with an SO2/O2 gas mixture. Metals such as Cu, Pb, Cr and Cd were successfully removed in a relatively short time. The effect of temperature and pH was investigated. Higher temperatures produced faster and higher recoveries with Pb and Cr more affected to temperature increase than Cu and Cd. The removal of copper, up to 50% percent, was achieved in alkaline solutions through the formation of copper sulfite complexes. The complete removal of metals such as Cu, Pb, Cr and Cd required that part of the treatment be carried out in acidic solutions. A preliminary cost analysis was carried out.

Jan 1, 2003

By Christian M. Sagedahl

The stringent environmental regulations for air pollution regarding emission control, along with the need of dry concentrates to feed autogenous smelting processes, are enhancing the development of cleaner technologies. Indirect drying of concentrates by a Kvaemer steam dryer is a technology with promising results, reducing dust entrainment to the exhaust gas stream and leading to smaller dust separation units. The Kvaemer dryers are designed for a very high availability, a high-energy efficiency, low amount and velocity of exhaust gases, no SO2, CO or CO, emissions combined with a wide range of satisfactory operating conditions and low total operational costs.

Jan 1, 1999

By Maribel L- Saucedo-Muñoz, Toshiyuki Hashida, Victor M. Lopez-Hirata, Shin-Ichi Komazaki

"Small-punch tests were conducted at 4, 77 and 293 K on three types of austenitic stainless steels JNl, JJl and JK2, which were solution treated, water-quenched and then aged at 923, 973, 1023 and 1073 K for 5 h. Small-punch test energy was employed for the evaluation of the aginginduced embrittlement behavior in these materials. Fracture surface of small punch test specimen for the solution treated steels exhibited a ductile fracture, showing the highest SP test energy values. The presence of intergranular brittle fracture was observed in aged specimens. Smallpunch test energy decreased significantly as the aging process progressed. The highest and lowest decrease in small-punch test energy with aging temperature occurred in JNl and JK2 steels, respectively. The decrease in small-punch test energy showed to examine appropriately the aging-induced embrittlement in these materials. The difference in aging-induced embrittlement behavior for these steels was explained based on the volume fraction of intergranular precipitates in aged samples.IntroductionA high level combination of strength and toughness is required for cryogenic structural materials used in the superconducting magnets of fusion nuclear reactor. This requirement is beyond the capability of conventional austenitic stainless steels [1]. The Japan Atomic Energy Research Institute (JAERI) developed new cryogenic JNl, JJl and JK2 austenitic stainless steels. The structure of superconducting magnets is supposed to be constructed by welding thick plates of this kind of steels. Thus, most of the components are exposed to thermal cycles. The slow cooling may cause microstructure changes in both the base material and weld zone. These changes may also decrease the fracture toughness of these materials at cryogenic temperatures. Therefore, it is important to study the effect of thermal aging on fracture toughness behavior for these steels. Konosu et al. [2] carried out a study of the effect of thermal aging on the mechanical properties for JNl steel using tension and fatigue tests. Kwon et al. [3] evaluated the deterioration in fracture toughness at cryogenic temperatures for the isothermally aged JNl steel by means of the Small-Punch (SP) test. No other reports were found about the cryogenic fracture toughness behavior for this kind of steels. To evaluate the cryogenic fracture behavior, the elastic-plastic Jrc value is a good alternative [4,5]; nevertheless, the standard required specimen size makes it difficult to be used for the fracture toughness evaluation in small zones."

Jan 1, 2011

By Gjergj Dodbiba, Atsushi Shibayama, Toyohisa Fujita, Takashi Shikazumi, Yukio Kato, Kenji Murata

"A new crushing or liberation technique by means of underwater explosion is put forward. This technique is suitable for crushing and liberating various materials, for instance: the electric parts of the discarded portable telephone, CPU from mother-boards of PCs, steel from plastics tubes used as construction materials, waste constructed materials like panels, tungsten carbide scraps, as well as slitting the optical disk (e.g. DVDs), etc. The materials to be crushed are immersed in water and then the explosion is carried out by using only a small amount of explosive. The shock waves in combination with the generated bubbles are very effective in liberating the materials of different densities. It was observed that the metals crushed or liberated by using this technique were leached much faster when compared with the conventional crushing technique. This crushing method can be applied for liberation of many kinds of electric or mechanical tools. Introduction The explosive has been used since Nobel’s invention in 1866. The main practical application of explosion is in the large scale public works, such as dam construction, land development, tunnel, mining and dismantlement of building. The shock wave caused by explosion extremely can generate high pressure able to break the concrete and rock, and other materials. In this study, the crushing and liberation of waste materials was carried out by explosion in water. The idea was to use this technique as a pretreatment stage prior to recycling. The explosion in water can be used to crush hard materials, helping the liberation between different attached materials. The samples used in this experimental work are waste materials such as construction materials, hose, cemented carbide, cellular phone, lithium buttery, DVD-R, etc."

Jan 1, 2008

This symposium is dedicated to the lifetime achievements of Professor H.Y. Sohn. It covers the scientific fields, processing routes and investigation techniques in which Prof. Sohn has worked during his career and is based in the equally important three topical areas: Principles, Technologies, and Industrial practice. Professor Sohn was General Chair of the very first TMS Fall Extraction and Processing Symposium in 1983 in San Francisco which led to the Annual such symposia as this International symposium. Furthermore, the theme of that symposium was sulfide smelting, which is also included in this symposium. [ ] Professor Sohn was born in a beautiful dynastic capital Kaesung, Korea on August 21, 1941. He received his B.S. degree in 1962 from Seoul National University, M.Sc. in 1966 from the University of New Brunswick, Fredericton, N.B., Canada, and his Ph.D. degree in 1970 from theUniversity of California at Berkeley all in Chemical Engineering. After working as a Research Associate at the State University of New York at Buffalo and as a Research Engineer at Du Pont?s Engineering Technology Laboratory, Dr. Sohn joined the Department of Metallurgical Engineering at the University of Utah in 1974 and currently holds the ranks of Professor of Metallurgical Engineering and Adjunct Professor of Chemical Engineering.

Jan 1, 2006

By Chai Li-yuan

Anodizing behaviors of magnesium alloys AZ31 at constant applied current, based on the electrolyte solution free of chromate or fluoride, were investigated. The anodizing process was influenced by constituents of electrolyte greatly. Therein, the oxylate salts, which led to the occurrence of the two totally different processes, played a determinant role in anodizing. They were stable and sparking process respectively. The morphology of anodizing film was observed by SEM and the structure of film was analyzed by XRD. During the stable process, a brown thin film was formed, however the sparking process led to the formation of white hard thick film. The functions of some kinds of additives, such as ammonia, glyceryl alcohol and PVP etc were also studied. Some of them had great effect on surface morphology of anodic film and some of them affected stability of anodizing process significantly.

Jan 1, 2006

By Manuel Pérez-Tello

An experimental study on the oxidation of chalcopyrite (CuFeS2), pyrite (FeS2), covellite (CuS) and chalcocite (Cu2S) particles was conducted by means of differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) techniques. Oxygen concentration in the process gas was set to 40 and 70% by vol. and a heating rate of 40 °C/min was used. Response variables included: the temperature of incipient reaction, the total exothermic heat of reaction, particle mass, morphology, and mineralogy of the reacted particles. Based on the experimental data and phase stability calculations, reaction mechanisms were proposed to represent the behavior of the particles during oxidation. The reaction mechanisms were verified by X-ray diffraction (XRD) analyses of the oxidized particles, and by thermochemical and mass balance calculations to reproduce the DSC and TGA thermograms. Overall kinetic models were developed to represent the evolution of the exothermic heat of reaction for each mineral as a function of time. Experiments conducted with copper concentrate particles containing the minerals studied suggest that the reaction mechanisms for the individual minerals can be used to represent the oxidation behavior of the copper concentrate particles.

Jan 1, 2006

By Cristián Araya L.

A dynamic agglomeration, heap leaching, solvent extraction and electrowinning software, called NICO, has been developed in order to either design or simulate copper ore recovery plants. NICO contains a library of routines, each representing a unit operation or piece of equipment, which are assembled like a meccano to match almost any wet plant configuration. Routines include agglomeration or curing either in drums or belts, belt conveyors, heap stacking and reclaiming, heap leaching of oxide, sulfide or mixed copper ores, heap irrigation, drainage, ponds, mixer-settlers, filters, columns, coalescers, tanks, electrowinning cells, pumps, and all connections and related piping. All models are semi- phenomenological, i.e., they include all physical-chemical, mass, thermal, transport equations, which are required to represent as closely as possible the equipment or unit operation. However, operating experience has been incorporated into the model in order to make it simpler, faster and reliable. This experience has been tested in several plants in Chile since 1992. Site meteorological data is simulated also; in this way the model is responsive to weather conditions (temperature, solar radiation, ambient humidity, atmospheric pressure, wind velocity, etc). NICO has been used recently for design and optimization studies in copper plants in Chile like Radomiro Tomic, Collahuasi and Zaldivar. A user-friendly interface allows fast and comprehensive simulations. The entire plant is shown in a single graphic screen, so the user can see all the relevant information, and soft-keys are provided in order to change parameters on-line and watch their effect in final copper production in cathodes. Model also calculates and reports operating parameters, as well as estimated investments and operating costs.

Jan 1, 1999

By Brian G. Thomas, Quan Yuan, Rajneesh Chaudhary, Rui Liu, Sana Mahmood

"A particle-entrapment model based on local force balances has been developed, implemented into computational models of turbulent fluid flow, and applied to simulate the entrapment of slag inclusions and bubbles during the continuous casting of steel slabs. Turbulent flow of molten steel is computed in the nozzle and mold using transient CFD models. Next, the transport and capture of over 30,000 particles are simulated using a Lagrangian approach. Particles touching the dendritic interface may be pushed away, dragged away by the transverse flow, or captured into the solidifying shell according to the results of a local balance of ten different forces. This criterion was validated by reproducing experimental results in two different systems. Finally, the model is applied to predict the entrapment distributions of different sized particles in a typical slab caster. Although more large particles are safely removed than small ones, the capture rate as defects is still high.IntroductionSurface defects such as slivers and blisters are often caused by captured inclusion clusters, slag, bubbles, and other particles. During continuous casting, jets of molten steel from the submerged entry nozzle (SEN) ports carry bubbles and inclusion particles into the mold cavity from upstream processing, as shown in Figure 1 [1]. In addition, droplets of liquid mold slag may become entrained into the flowing steel due to fluid flow problems, via several different mechanisms [2]. Figure 2 shows some typical inclusion particles [3] that can be entrapped from the flowing liquid into the solidifying steel shell to form defects in continuous-cast product.Liquid steel flow in the continuous casting mold has been modeled extensively. Reynolds Average Navier-Stokes (RANS and URANS) approaches are based on accurate computation of the ensemble-averaged velocity field. Particle transport can be tracked using a Lagrangian approach, introducing an extra model, such as ""random walk"" to generate realistic motion of every particle. Large Eddy Simulation (LES) models can accurately calculate both the transient evolving flow field and Lagrangian particle motion [4, 5] of this turbulent process."

Jan 1, 2012

By Hiroyuki Sano, Chikabumi Yamauchi, Mitsuru Tanahashi, Toshiharu Fujisawa, Shin-ya Iwahori

"Pyrometallurgical process using Cu2O-based slag was proposed as a recycling process for copper scrap. However, it is difficult to remove nickel from copper by oxidative refining. Therefore, it is necessary to reduce the concentration of nickel in copper before the oxidative refining. In the present work, the copper enrichment stage in this recycling process, where copper scrap melt is separated into the Fe-C-Cu melt and the molten copper, was taken up and the compositions of both melts were measured. Based on the above results, the distribution ratios of nickel between the Fe-C-Cu melt and the molten copper were calculated. Furthermore, the optimum condition of copper enrichment stage was discussed from the viewpoint of nickel removal and copper recovery. The possibility of recovering 4N-purity copper by using this recycling process was confirmed.IntroductionRecycling is well known as a method for saving resources and reducing environmental damage. More than 99% of copper is used in metallic form - as metal or copper alloys[l]. High-grade copper scrap is directly re-melted and reused, while low-grade copper scrap is transported to copper smelters to be pyrorefined and electrorefined. Nevertheless, a great amount of copper is being stockpiled in the cities and should be recycled in the near future. At that time, the current recycling process will face new problems due to the increases in the recycling rate to the smelters. This includes insufficient combustion heat to melt copper scrap and ·almost no benefit in electrorefining because the scrap does not contain gold and silver. Thus, an alternative pyrometallurgical method for copper scrap refining will be required."

Jan 1, 2000

This symposium is dedicated to the lifetime achievements of Professor H.Y. Sohn. It covers the scientific fields, processing routes and investigation techniques in which Prof. Sohn has worked during his career and is based in the equally important three topical areas: Principles, Technologies, and Industrial practice. Professor Sohn was General Chair of the very first TMS Fall Extraction and Processing Symposium in 1983 in San Francisco which led to the Annual such symposia as this International symposium. Furthermore, the theme of that symposium was sulfide smelting, which is also included in this symposium. [ ] Professor Sohn was born in a beautiful dynastic capital Kaesung, Korea on August 21, 1941. He received his B.S. degree in 1962 from Seoul National University, M.Sc. in 1966 from the University of New Brunswick, Fredericton, N.B., Canada, and his Ph.D. degree in 1970 from the University of California at Berkeley all in Chemical Engineering. After working as a Research Associate at the State University of New York at Buffalo and as a Research Engineer at Du Pont?s Engineering Technology Laboratory, Dr. Sohn joined the Department of Metallurgical Engineering at the University of Utah in 1974 and currently holds the ranks of Professor of Metallurgical Engineering and Adjunct Professor of Chemical Engineering.

Jan 1, 2006

By Kiichiro Hayashi

"Indonesia is one of the world leaders in palm oil production. Palm oil industry is an industry to be considered when it comes to environmental impacts. This paper utilizes three step approaches. First, a material flow analysis of palm oil related industry was conducted in Indonesia. Second, a factory visit survey was conducted for getting information on environmental impacts of plantation and CPO mills. Third, a LCA study was made for a model Indonesian CPO mill in several bio-waste treatment options. Main findings were that, first; over 70% of FFB was bio-wastes generated from CPO mills. Second, some mills introduced a zero emission bio-waste policy. However, untreated bio-wastes in the zero emission policy, such as, CH4 from POME ponds, may have potential to reduce more impacts on the environment. Introduction Indonesia is one of the world leaders in palm oil production with approximately 12.4 million tons of crude palm oil (CPO) production in 2005 and with the plantation area 5.6 million ha spreading out in 19 provinces [10]. The expansion of palm oil cultivation in Indonesia and its export oriented industry heavily relies on the strong world market demand for food. Currently, there are 320 CPO industries in Indonesia [10]. These include plantations and palm oil related factories. Among them, there are six biggest players in CPO business in Indonesia: PT. Perkebunan Nusantara (PTPN) consisting of 9 PTPN, Sinar Mas, Raja Garuda Mas, Astra Agro Lestari, Minamas Plantation and Indofood. They are managing more than 50% of plantation estate in Indonesia and are leading the Indonesian palm oil business.Palm oil industry is an industry to be considered when it comes to environmental impacts. Unfortunately, there is not so much available information related to the performance of each CPO on environmental impacts. There are reports which provide information on environmental impacts of CPO mills in South East Asian countries, but are limited to, for instance, Thailand’s cases [4 and 5] and Malaysia’s cases [1, 3, 6, 7, 9, 11 and 12]. On the other hand, similar studies on the Indonesian’s case are not well established in academic literatures. And also there is limitation on Indonesian palm oil industrial information from plantation to consumption and disposal in academic articles. There is no literature related to material flow analysis focusing on the whole Indonesian palm oil related industry. One way to describe and present the environmental impacts is through a life cycle assessment (LCA). The LCA could be used to estimate the impacts of CPO production including the stages of plantation, transportation and milling [5, 8 and 11]. However, studies on Indonesian CPO production process were not well established in academic articles. The purpose of this paper is thus to clarify environmental impacts of palm oil industry in Indonesia especially by focusing on plantation and CPO mills with consideration to various bio-waste treatments."

Jan 1, 2008

By Kurt A. M. Westerlund

The basic function of primary gas handling downstream non-ferrous pyro-metallurgical processes is cooling hot sticky gases to treatable temperature levels (e.g. entering ESP). That means managing efficient the critical gaseous components from a molten via a sticky to a solid phase. The article outlines the modem gas cooling methods combined with efficient heat recovery. Examples of the alternative use of recovered steam energy are outlined; as e.g. drying of concentrate and power generation. The heat transfer impact of the insulating dust is called fouling and circumstances causing fouling are described. Modem cooling surface design and cleaning techniques to keep fouling in reasonable limits are described. Leakage- and false air ingress into the gas handling lines often limits smelting capacity. The objective is generally to minimize the infiltration of air but it still takes place at open interfaces (e.g. at reactor hood, feed port). Leakage air at furnace roofs for example can be reduced to a minimum by adopting the pressure gas sealing used at present In-Bath-Lance furnaces. Modernization and optimization methods to de-bottleneck existing waste heat boiler gas cooling capacity by highly efficient surface cleaning systems and false air avoiding (e.g. bundle roof boxes, dust discharge) are detailed described.

Jan 1, 1999