Search Documents

By Suman Das, Justin J. Gambone, Rohan Bansal, Ranadip Acharya

"This paper focuses on modeling of the scanning laser epitaxy (SLE) process that is currently being investigated and developed at the Georgia Institute of Technology. SLE is a laser-based manufacturing process for the creation of equiaxed, directionally solidified and single-crystal deposits of nickel superalloys onto superalloy substrates through melting and resolidifícation of alloy powders using a scanning laser beam. The thermal modeling of the system, done in a commercial CFD software package, simulates a heat source moving over a powder bed and dynamically adjusts the property values for consolidating CMSX-4 nickel superalloy powder. The associated melting and re-solidification process is modeled using an immediate consolidation approach, and the predicted melt depth is compared with the experimental data obtained. For a given position of the beam, geometrical parameters of the melt pool are used to estimate the resulting microstructure. The influence of the processing parameters on the microstructural evolution is also discussed. This work is sponsored by the Office of Naval Research through grants N00173-07-1-G031, N00014-10-1-0526 and N00014-11-1-0670.IntroductionIn order to increase the operating temperature of gas turbine aero engines, investment cast equiaxed turbine airfoils are now often replaced with airfoils that have either directionally solidified columnar or single crystal (SX) microstructure. Wear and damage during operation limits the lifetime of these components and necessitates the replacement of numerous airfoils within the engines. Due to the high cost of producing SX cast turbine blades, the cost of replacing each blade can be several hundred to several thousand dollars. With each engine containing several hundred blades, the cost to replace all blades can reach hundreds of thousands of dollars. Hence, it is of great interest to develop a process that can restore the single crystal microstructure at the locations of material loss and allow for the blades to be repaired and reused rather than be scrapped and replaced."

Jan 1, 2012

By A. V. Tarasov, S. D. Klushin

493 The most common method for minimizing the copper content of residual slag in the process of autogenous smelting of sulfide raw materials is treatment of molten slag in an electric furnace, with optional addition of solid reducing agents, such as coke, and/or sulfiding agents such as pyrite. A drawback of this technique is the fact that the final slag produced still contains 0.5% or more Cu. We have tested a method for treating molten slag obtained as a result of autogenous smelting by a gaseous mixture of sulfur dioxide and methane at a ratio of. SC:SO2 = 0.75 :1.0 in the presence of oxygen. Interaction reaction within the SO2-O2-CRi system proceeded at a high rate at 1373 to 1573 K to form reducing and sulfiding agents: H2S, S, COS, CO, CO2, H2, H2O. The gas mixture requirement was about 100 to 150 Nm3 per 1 tonne of slag. A decrease in the ferric iron concentration (Fe3+) from 10-15% down to 2-3% resulted in lower solubility of copper in slag, and agitation of the melt with gas stream accelerated. the separation of the sulfide phase and slag. Removal of copper from slag was performed in a pilot unit within the second V anyukov furnace zone where slag arrived with a copper content of 0.8-1.3%. The temperature of molten slag was maintained within 1523 to 1573 K. The copper content of the final slag was at a level of0.12 to 0.14%. The matte sent to converting was a mixture of bottom matte from the smelting zone and the slag treatment zone. It had a copper content of about 50 to 55%. Process gases from both furnace zones were combined and sent to the acid plant for sulfur recovery. This process was offered for commercial use at two copper smelters in Russia and CIS.

Jan 1, 2000

By Hee Dong Jang, Hong Yong Sohn, Miguel Olivas-Martinez

"Tetramethylorthosilicate (TMOS), a precursor of silica nanoparticles, is prepared from the waste silicon sludge, followed by the synthesis of silica nanoparticles from the TMOS by flame spray pyrolysis. A two-dimensional multiphase computational fluid dynamics (CFD) model for the flame spray pyrolysis process (FSP) for the synthesis of silica nanoparticles has been developed. The model incorporates the governing turbulent equations of overall continuity, momentum, energy and species mass transport to represent the gas phase and the population balance model (PBM) to account for the silica nanoparticles. The model has been validated with experimental data in terms of gas temperature and average particle size. Introduction Silica (SiO2) nanoparticles are used in various industrial applications, such as catalyst, pigments, thin film substrates, electronic and thermal insulators, and humidity sensors [1]. They are also used as additives in plastics and rubbers to improve the mechanical properties of elastomers, and in liquid systems to improve their suspension behavior. These applications rely on the particle morphology, average particle size, particle size distribution, and phase composition [2]. Silica nanoparticles can be synthesized by wet chemical processes such as sol-gel methods and high-temperature processes such as flame spray pyrolysis (FSP). The FSP process provides a unique control of particle size and crystalline structure and it can also produce high-purity, thermally stable particles continuously with minimal further treatments. The sizes of the flame- made particles range from a few to several hundred nanometers, depending on the operating conditions [1]. The synthesis of silica nanoparticles from organic compounds that contain silicon by the FSP process is of interest because it generates no harmful by-products [1, 3]. Several compounds such as tetraethylorthosilicate (TEOS) and tetramethylorthosilicate (TMOS) can be used to synthesize silica nanoparticles, but most such compounds are expensive. Thus, it is desirable to prepare the precursor compounds from waste materials. In the present study, TEOS and TMOS synthesized from silicon sludge were used as precursors of silica nanoparticles [4]."

Jan 1, 2008

By C. A. Nogueira, F. Pedrosa, F. Margarido, R. N. G. Guerra

"A hydrometallurgical process for recycling spent Zn-MnO2 batteries was developed, involving leaching with sulfuric acid, purification by precipitation and metals separation for further recovery. Leaching of zinc oxide was easily attained while for manganese oxide was rather difficult depending on temperature and acid concentration. At 90°C and with the liquid/solid ratio of 20 L/kg, more than 95% of zinc is recovered in 30 minutes with 0.5M H2SO4. To attain similar recovery for manganese, higher levels of acid concentration and time are needed (e.g 0.7 M and 2 hours). After leaching a purification step is necessary to remove iron co-dissolved through Fe(III) precipitation. Separation of zinc from manganese by solvent extraction with 1M DEHPA follows in the process route. The countercurrent multistage separation diagram developed allows the production of a zinc electrolyte with 120 g/L Zn and 0.005 g/L Mn, and a raffinate with 16 g/L Mn and 0.013 g/L Zn.IntroductionThe recycling of spent Zn-MnO2 batteries is carried out by dedicated recyclers using several process alternatives [1]. Most of the running processes use pyrometallurgical technologies [2] based on zinc distillation. Alternative treatments by hydrometallurgy have been reported [3-5] but its application is scarce.In order to contribute to the development of alternative solutions, a process for recycling batteries based on Zn-MnO2 systems has been studied. The process is based on the hydrometallurgical treatment of spent batteries in sulfuric acid media (Figure 1). The process starts with the physical processing by shredding using cutting grinders, where the batteries are opened and size reduced, allowing the liberation of the interior electrode particles or pastes. The fines can be then separated and the coarse material containing the steel scrap can be treated to remove the remaining aggregate electrode. The final scrap also contains some plastics and other non-metal materials and can be further valorized."

Jan 1, 2008

By Guozhu Ye, Mikael Larsson, Eric Burström, Sten Ångström

"Increased use of scrap in steelmaking including scrap use in BOF has a high economic and environmental potential in terms of increased productivity, energy saving and reduced emission of CO2. Preheating and surface cleaning of steel scrap is a concept developed by MEFOS in a four year research program funded by MISTRA, Swedish Foundation of Strategic Environmental Research. The process concept consists of four major steps: 1) Combustion of ASR or other waste fuel and composing of the gas composition. 2) Scrap heating and cleaning in a shaft where the coated zinc is removed as ZnCl2 and scrap is heated to about 600 ºC. 3) Dust separation for recovery of metal zinc. 4) Gas cleaning. This paper will describe the process concept and highlight the major results from preliminary trials around the scrap heating and cleaning shaft.IntroductionSteel is often coated to increase the corrosion resistance. Share of coated and galvanized steel in the world marked is steadily increasing. This results in increased amounts of scrap with different types of coatings. Use of galvanized scrap in EAF plant results in an EAF dust with high content of zinc ferrite and many other impurities like Pb, Hg, Cd and halide. EAF dust is classified as hazardous waste in most of the developed countries and the steel plant has to pay for external treatment for zinc recovery. For use in BOF plant this will result in a BOF dust containing typically 1-5%Zn making it impossible for recycling to the blast furnace.Different approaches for surface cleaning have been investigated in past. Dapper et al. [1] examined the possibility to evaporate Zn, Ni, Cr, Sn from coated materials using chlorine. Chlorinated rinsing of non iron oxides and metals using HCl from combustion of PVC was discussed by Fray [2]. Further studies by Tee and Fray [3-5] have been concentrated on the possibility to vaporize coatings with an air and chlorine gas mixture. The O2:Cl2 ratio in the gas mixture was found to have great importance for control of the process. To avoid the chlorination of iron, this ratio should be kept at a level of 10:1.Scrap pre-heating up to about 600 ºC is a well known method and this alone could save up to 100 kWh per ton steel. The technology has been established since many years and efficient processes were developed in the 90’s. However, no process has fully gained the expected energy savings as the large quantity of the exhaust gas has to be reheated to over 1000 ºC again to destroy the hazardous components like dioxins."

Jan 1, 2008

By Shirley Cosin, Guillermo R. Martín-Cortés, Francisco R. Valenzuela-Díaz, Jorge E. Di Rito, Valquiria F. J. Kozievitch

"A procedure that is being studied as a potential method for correct disposal of industrial wastes by incorporation on common clay bodies in the fabrication of structural ceramic products as bricks, blocks and roof tiles. The objective of this paper is to present the results obtained with mixtures of unburned sanitary ware wastes with a common clay from Jundiai, São Paulo, Brazil. Preliminary tests of incorporation (1,0% to 30,0% in weight) were made with hand formed spherical test bodies. With the proportion that presented spheres with the higher compression strength after drying and after firing (950°C) prismatic samples were extruded. Based on the ceramic properties of those mixtures an industrial test was performed. Six hundred hallow blocks containing 30% waste were fabricated and presented ceramic properties similar to those without incorporation. Introduction The sanitary ware segment has a very great prominence in South America, placing Brazil as one of the greater producers of the world.. Inside the country, the city of Jundiai, in the State of São Paulo is the greater producer region of this ware. Great part of the material is destined to exportation and daily it is produced high number parts. High exportation requirements make that the amount of powder waste rejects reach astronomical volumes. Until the moment too small part of that material it is re-taken with advantage, because in the own segment, there is not an economic viability, by the fact of the exigencies concerning the quality of the final product [1]. If from one side it exists that material that at the moment is deposited in landfills, or stored at the patio’s factories, from the other side the exigency of adopting exploitation rules, recycling and obedience to Laws relative to the environment as ABNT 10400, therefore it is a material that if well studied, it will certainty have a noble destiny [1]."

Jan 1, 2008

By Somayeh Dashti, Ehsan Vahidi, Fereshteh Rashchi

"The main goals in zinc electrowinning process are decreasing of power consumption and increasing of current efficiency. In this study, the electrowinning of zinc in the presence of different additives in electrolyte were established and Arabic Gum, Gelatine, sodium lauryl sulphate and l-hexyl-3-methylimidazolium hydrogen sulfate in the five levels using Taguchi method was examined. In our previous researches, using orthogonal array, effect of zinc electrowinning parameters such as anode type, current density, sulphuric acid concentration, temperature and zinc ion concentration was studied and the optimized conditions for zinc electrowinning was obtained. Anode composition: Pb-Ag 0.5%-Sn2%-Sb1%, current density (A/m2):500, acid concentration (g/1):165, temperature: 60°C, zinc ion concentration (g/1):70. The main goals in zinc electrowinning process are decreasing of power consumption and increasing of current efficiency. ln this research, the effect of four additives: Gum Arabic, Gelatine, sodium lauryl sulphate and an organic material in the four levels with Taguchi method was examined. ln fact the effect of electrolyte environment and determining the best electrolyte under the optimized conditions is the main aim of this study.IntroductionDue to its low cost and abundance, zinc is widely used in the production of brass, galvanized steel, sacrificed anodes and primary and secondary batteries [I]. Some 80% of world primary zinc production is derived via roast-leach-electrowinning processes [2-4]. In the electrowinning process to both improve final product quality and current efficiency the leachate should be purified [5].To produce zinc a current method is to extractit from acidic zinc sulphate solutions by electrolysis with aluminum cathodes and insoluble lead-based anodes [6]. Though the electrolytic processing of zinc has been performed for many years, there are still current efficiency problems in the cathodic process. These low efficiencies (88- 93%) have a serious impact on the costs associated with the energy consumption. On the other hand, these low efficiencies increase energy consumption and decrease the quality of the surface morphology [7- 8]."

Jan 1, 2012

By Monteirom Sergio N., Romulo L. Loiola, Giulio R. Altoe, Noan Simonassi, Frederico M. Margem

"The environmental concern is creating pressure for the substitution of high energy consumption materials for natural and sustainable ones. Compared to synthetic fibers, natural fibers have shown advantages in technical aspects such as flexibility and toughness. So there is a growing worldwide interest in the use of these fibers. Buriti fiber extracted from buriti palm tree (Mauritia flexuosa), presents some significant characteristic, but until now only few studies on buriti fiber were performed. This work aims to make the analysis of the tensile strength of epoxy composites reinforced with buriti fibers. This analysis was performed in fibers with diameters between 0.1 and 0.4 mm. Those fibers were incorporated into the epoxy matrix with volume fraction from 0 to 30%. The fiber diameters were measured by a profile projector. After fracture the specimens were analyzed by a SEM (scanning electron microscope).IntroductionNatural fibers with high amount of cellulose, also known as lignocellulosic fibers, have been used from primeval times of our civilization. In the last century, synthetic fibers such as nylon, carbon, aramid and glass fibers gained interest owing to superior strength and precise dimensional control. Natural fibers were then replaced by synthetics in many fields such as textiles, sports goods and appliances. In the past decades, however, environmental issues drawn, once again, the attention to lignocellulosic fibers as possible substitute for intensive energy-consuming and long term polluting synthetics, specially the glass fiber(1). In particular, research works have disclosed the potential advantages associated with the use of lignocellulosic fibers as the reinforcing phase in polymer composites(2-3). Among the advantages it is worth mentioning the renewability, recyclability, biodegradability and the fact that natural fibers are neutral with respect to CO2 emissions responsible for global warming. In addition to environmental benefits(l,10) the lignocellulosic fibers present economical advantages, such as worldwide abundance and comparatively low costs as well as some technical properties associated with flexibility and toughness( 4), which contribute to the performance of automobile components fabricated with natural fibers composites(l 1-13)."

Jan 1, 2013

By Satoshi Itoh

Phase equilibria and activities of the components in the liquid lead-antimony-oxygen ternary system, which is of fundamental importance for discussing the' recovery of lead and antimony from a used lead-battery, have been investigated at 1173 and 1223 K. The two liquid phases of metal and oxide were observed at the temperatures studied, and the tie lines indicating isoactivities were determined. The activities of PbO, SbO1.5 and Sb2O3) in the PbO-SbO1.5 and PbO-Sb2O3 pseudo-binary systems were then obtained by applying the Gibbs-Duhem equation to the phase relation of metal-oxide equilibrium. Both in the pseudo-binary systems the activities exhibit negative deviations from Raoult's law. The vapor pressures of lead, antimony and lead oxide, antimony oxide were calculated by using the activities of the components in the lead-antimony-oxygen ternary system. As a result, an oxidation of antimony concentrated in an anode slime followed by evaporation as antimony oxide Sb406 was found to be considerably effective for the recovery of lead and antimony from a used lead-battery.

Jan 1, 2003

By C. Lupi

Electric arc furnace dust generated during the production of steels is regarded as hazardous waste because of the presence of leachable elements such as Cr, Pb, Cd .... Different processes are available according to the management policy chosen by the steelmaker: disposal. recycle and/or recovery. The feasibility of an hydrometallurgical Zn recovery process on fumes generated during the pyrometallurgical treatment of EAF dust has been investigated. The recovery of metallic iron, chromium and nickel as molten metal provides fumes very rich in zinc oxide ( 63.1% ) and poor in zinc ferrite. This secondary dust is still an hazardous waste and represents the raw material for the recovery of Zn and Pb. The waste material is first leached in 1.5 M sulphuric acid at 30°C to provide a Zn, Fe and Mn rich aqueous solution and a Pb and Ca sulphate rich sludge. The iron is eliminated by precipitation because is harmful to the following electrowinning process. The ftltered and purified leached solution is acidified in order to obtain good electrowinning conditions. A pure cathodic deposit of zinc is then produced in an electrolytic cell at laboratory scale.

Jan 1, 1996

By K. O. Fagerlund

Theoretically and experimentally determined copper matte settling rate in iron silicate slag has been discussed. Separation and settling rate measurements of sand, homogenised slag and 25%Cu concentrate, 63%Cu industrial, and 71%Cu synthetic copper mattes were carried out by mixing crushed slag and matte samples with silica sand in an alumina crucible and melting at 1300-1350°C. Two different types of slag compositions were employed, with Fe/SiO2-ratio 1.4 and 1.7. The separation rate was followed by taking samples from the .melt. As expected, the settling rate of copper matte in fayalite slag depended on the slag composition, where the increasing silica decreased the matte settling rate. Microanalysis of solidified slags showed that the rate of separation of low grade matte was low compared with high grade matte and the presence of a very small size fraction of matte droplets in slag remained unsettled in stagnant fluid. The production of sulfur dioxide gas inside the molten bath was found to be possible up to a certain iron sulfide content in the matte. Also, copper matte settling rates in industrial furnaces have been discussed.

Jan 1, 1999

By V. A. Shumsky, I. P. Polyakov, N. M. Ospanov, M. A. Lyamina, N. N. Ushakov

Studies on the kinetics of the competitive processes of PbS volatilization and PbS oxidation, as applied to the heat and mass transfer conditions in the flame of the Kivcet furnace, revealed that the rate-determining factor is the supply of heat. Therefore, low yields of fume in the autogenous flash smelting of lead sulphide feeds are noted despite the high volatility of PbS at 1,300-1,400°C. Dust formation in the autogenous flash smelting of Kivcet-smelters does not exceed 5-7%, of which fumes amount to ~ 80%. Using extra fuel during autogenous smelting involves the mismatch of the sulphide oxidation rate and the release of heat in the flame, and increases the fume yield. This is a major cause of the high dust formation in pilot plant trials. The analysis of dust formation in the Kivcet smelting of oxidized lead feeds in an industrialscale smelter shows an overall increase of dust formation (up to 10% of the feed), with fumes constituting ~ 80% of the dust. A pronounced increase of the zinc component of the fumes is also noted. Lead

Jan 1, 2000

By Chenhui Liu, Hong-ying Xia, Bingguo Liu, Wei Li, Jinhui Peng, Libo Zhang

"Dielectric property is an important limiting factor in the development of microwave processing of minerals and ores. In this study, we used an open-ended coaxial sensor method to measure the complex permittivity of an ilmenite concentrate (41%TiC>2) and microwave absorption properties from room temperature to 100°C. The results show that the dielectric constant, loss factor and loss tangent increase with temperature rising at 2.45GHz. Microwave absorption properties of this ore are highly dependent on temperature and frequency. Ilmenite concentrate can be used as raw materials to prepare wideband microwave absorbing material. The research will be helpful in explaining the thermal running of microwave dielectric heating the ilmenite concentrate.IntroductionAs the sources of high-grade titanic mineral are decreasing worldwide, the utilization of low-grade minerals such as ilmenite has attracted more attention [1,2]. Because Panzhihua ilmenite has complex minerals and high contents of MgO, CaO, S1O2 , it is difficult to upgrade the ilmenite to titanium-rich slag and farther produce synthetic rutile and titanium dioxide pigment [3]. Therefore, it is desirable to develop new technology for processing ilmenite ore [4]."

Jan 1, 2012

By Sergio Neves Monteiro, Nuã Simonassi, Helvio Pessanha Guimarães Santafé Jr.

"Thermoset polymers, like the polyester, become harder with increasing temperature owing to molecular crosslink formation, which is a thermal benefit for composite matrix applications. Natural lignocellulosic fibers, however, have low thermal resistance and tend to degrade with increasing temperature. Therefore, the combination of a lignocellulosic fiber, as reinforcement, with a thermoset polymer, as the matrix, results in a composite material with complex thermal behavior. In the present work, a thermal analysis was conducted on polyester composites with different amounts of coir fibers. Both TGA and DTG curves were analyzed to determine the effect of the coir fiber on the thermal resistance of the composites. It was found that the coir fiber sensibly affects the thermal behavior of the polyester matrix for fiber amounts above 10% in volume. This effect is associated with an increase in thermal degradation.IntroductionIn recent years, there has been an increase application of natural fibers as reinforcement of polymer matrix composites in several industrial sectors, with special participation in automobile components [1-3]. Figure 1 illustrates the different components of a modem BMW sedan that are fabricated with lignocellulosic reinforced polymer composites."

Jan 1, 2012

By M. Z. Sukiennik

A static method for vapor pressure measurement up to 1450 K and above 1 hPa is presented. The method is designed for equilibrium and kinetic studies of metallic systems, including those with a chemical reaction. Application examples are given for determination of activities in condensed phases, and heterogeneous reaction rates and equilibrium constants.

Jan 1, 1993

By W. G. Davenport

Most pre-t 988 Outokumpu flash furnaces were built with blast heaters. Many continue to use them. Blast temperatures in these smelters· are typically 400 to 700 K (Table 2. 1) This chapter: (a) shows how hot blast is included in our calculations (b) evaluates the effects orhot blast onauthothermal65% Cu matte production.

Jan 1, 2001

By Md Sazzadur Rahman

Electrochemical Impedance Spectroscopy studies were conducted on two organic thermal energy storage materials; Neopentylglycol (NPG) and 2-Amino-2-Methyl-1,3-Propanediol (AMPL). The ionic conductivities and dielectric relaxation times in the low temperature ordered a-phase (monoclinic for both NPG and AMPL) as well as high temperature orientationally disordered cubic y-phase are reported.

Jan 1, 2006

By M. S. Moats

The treatment of oxidized residues of zinc with high iron content continues to present a technical challenge in both the steel and zinc industries. Two main problems are commonly identified and include high treatment costs and environmental concerns about contaminated, iron-bearing residuals. A new approach to this problem is described in which selective separation of the iron and zinc into salable products may be potentially feasible. The waste material is first leached to give a solution having an approximate concentration of 110 g/l Zn, 15 g/1 Fe and 40 g/1 H2SO4 and other impurities such as Pb, Cd, Cu and Sb. A suitable organic, such as D2EHPA, is used to load the majority of the iron. The aqueous phase is then acceptable for zinc electrowinning after standard solution purification. The novel step in the flow sheet is the efficient recovery of the ferric iron from the organic solvent using a solid metal to reduce the iron to the ferrous state. The Fe+2 is easily stripped into an aqueous phase in a relatively pure form, suitable for use in water treatment. Process parameters and possible flow sheet designs are described and discussed.

Jan 1, 1995

By Kosei Morita, Osamu Nakano, Katsuhiko Nagai, Kazuhiro Mori

"The Sumitomo Toyo Smelter and Refinery commenced its operation in 1971 with three Peirce- Smith (PS) converters. “2 hot – 1 blowing” operation was practiced, that is one of two available converters was blowing and the other was standby in a hot state while the third converter was under repair. After several improvements, the stack time ratio reached around 90%; and processing 5 batches a day became possible.As a result of the expansion program of the Toyo smelter and refinery that started in 2001, the converter operation pattern was shifted from “2 hot – 1 blowing” to “2 hot – 2 blowing” with the installation of second converter blowers and an additional ladle crane.In 2005 a, the fourth converter was installed and “3 hot – 2 blowing” operation began. Also, with improvements experienced in the anode furnaces and the anode-casting wheel operation, today, the number of cycles has been increased up to more than 8.5 a day.The treatment techniques of fugitive gas containing sulfur dioxide from converter furnaces have been gradually reinforced, and the fixation rate of treated sulfur is currently being maintained at more than 99.9%. This paper introduces the operations described above, and the improvements in environmental management techniques for the Toyo PS converter operation."

Jan 1, 2009

By M. J. Adam

As part of its research programs, the Bureau of Mines is investigating the partitioning of complex sulfide minerals to simpler sulfide phases by sulfidation reactions. Partitioning in this manner can afford opportunity to improve selective extraction of mineral constituents of value. This report describes research involving the sulfidation partitioning of the mineral pentlandite, which is an important source of Ni in primary production. For the laboratory studies, the pentlandite was synthesized in nominally equiatomic proportions of Ni and Fe. Elemental Ni, Fe, and S powders were blended, compacted, and sealed under reduced He pressure in vitreous silica tubes. The tubes were heated under controlled conditions at SOD? C for 24 h. The product was verified by X-ray diffraction and chemical analysis to consist essentially of (Ni,Fe)9S8. Small samples of the (Ni,Fe) S were encapsulated with sulfur in silica tubes at reduced He pressures and heated for 1 to 24 h at specific temperatures between 400? and 600? C, both below and above the boiling point of sulfur (_445° Cl. Reaction rate increased with temperature. Within this temperature range, partitioning to individual Ni and Fe disu1fides proceeded to essential completion according to the reaction

Jan 1, 1988