Search Documents

By Raghavan Srinivasan, Y. V. R. K. Prasad, William G. Frazier, Steve C. Medeiros

"Aerospace gas turbine disks operate in an environment of relatively high stresses caused by centrifugal forces and elevated temperatures. These severe conditions necessitate the need for materials with good high temperature strength and low cycle fatigue resistance. One class of alloys used for this task is the nickel base superalloys, out of which, lN 718 is the most widely used in the aerospace industry [I]. The properties of IN 718 are attributed to the combined effects of the chemistry, heat treatment, and microstructure. The chemistry is tailored not only for solid solution strengthening but also for precipitation hardening developed during heat treatment, which combined with a fine grained microstructure lead to excellent mechanical properties such as low cycle fatigue resistance and elevated temperature strength. The properties of a gas turbine disk are sensitive to the microstructure, in particular the grain size, which is dependent on the processing history. The ability to precisely control the microstructural development during forging is dependent on controlling the process so that the workpiece is deformed within a ""safe"" region where no microstructural damage or flow instabilities occur. The microstructural mechanisms during deformation may themselves vary within the ""safe"" region and it is desirable to determine them within the range of parameters that are commonly used in industrial processing. The objective of this work is to establish a relationship between the grain size and the process control parameters i.e., temperature and strain rate, in the hot working of IN 178.BackgroundIN 718 belongs to a class of nickel-iron base superalloys with a face-centered cubic (FCC) austenitic matrix strengthened by precipitation of ordered intermetallic or carbide precipitates and is a nickel-rich alloy strengthened by ordered body centered tetragonal (BCT) precipitates, Y"". The alloying of nickel and iron results in the formation of the austenitic matrix, y, while the addition of chromium and molybdenum cause solid solution strengthening. Also, alloying with niobium causes precipitation of the metastable hardening constituent Y"" (Ni3(Nb,Ti)). Extended aging treatments in the temperature range 650 °C - 980 °C allow the more stable orthorhombic 8 phase (Ni3Nb) to form. Trace amounts of boron are also added to serve as grain boundary strengtheners for high temperature creep resistance. Hot deformation of IN 718 is performed between the Y"" and 8 solvus temperatures to facilitate recrystallization and to control grain growth. While deformation below the Y"" solvus (""""962°C) produces no change in grain size, deformation above the Y"" solvus but below the 8 solvus will lead to a dynamically recrystallized microstructure. The presence of the 8 precipitates will pin the grain boundaries after recrystallization and restrict grain growth so that a fine grain microstructure is obtained. Deformation above the 8 solvus ("""" 1038°C) will lead to a microstructure which has undergone grain growth during deformation."

Jan 1, 2000

By G. Scavino

A 0.5 wt.% C, 22 wt.% Mn austenitic steel, recently proposed for fabricating automotive body structures by cold sheet forming, due to favorable overall strength and ductility, exhibits plastic localizations during uniaxial tensile tests, whereas no localization happens during biaxial Erichsen cupping tests. Full-thickness tensile and Erichsen specimens, cut from as-produced sheets, were polished and tested at different strain rates. During the tensile tests, the plastic localization phenomena consist first of macroscopic deformation bands traveling along the tensile axis, and then of series of stationary deformation bands, each adjacent to the preceding ones; both types of bands involve the full specimen width and yield macroscopically observable surface relief. No comparable surface relief was observed during the standard Erichsen tests. The stress state being known to influence plastic localization phenomena, reduced-width Erichsen tests were performed with 10 to 30 mm width polished specimens, in order to explore the transition from biaxial to uniaxial loading.

Jan 1, 2009

By Carole Read

Hydrogen is under consideration by several countries for its potential as an energy carrier for transportation applications. In order to compete with vehicles in use today, hydrogen-powered vehicles will require a driving range of greater than 300-miles in order to meet customer needs and expectations. For the overall vehicular light-duty fleet, this dictates that a range of 5 to 13 kg of hydrogen be stored on-board (assuming a fuel cell power plant) within stringent system weight, volume, and cost constraints. Vehicular hydrogen storage thus constitutes a major scientific and technological challenge. To meet this challenge, the U.S. Department of Energy (DOE) initiated a ?National Hydrogen Storage Project? with roughly 40 universities, 15 companies and 10 federal laboratories, actively engaged in hydrogen storage research. Centers of Excellence in metal hydrides, chemical hydrides, and carbon-based materials have been established, as well as independent university and industry projects in the areas of new concepts/materials, hydrogen storage testing, and storage system analysis. Recent technical progress in each of these areas is discussed, as well as collaborative hydrogen storage activities under the recently established International Partnership for the Hydrogen Economy (IPHE).

Jan 1, 2006

By Claudio Toro, Alex Moyano, Rodrigo Díaz, Hugo Jara, Carlos Caballero, Pedro Morales, Leandro Guzmán

"During 2007, Codelco-Chile carried out industrial tests to validate the Continuous Converting Process in the Teniente Converter of the Codelco Norte smelter.For planning and starting up the tests, a predictive, analytical and dynamic model was developed to support operational decisions. The dynamic model was developed using the METSIM® platform and dynamic data exchange (DDE) to operate smoothly with MS Excel®. The main feature of this real-time model was the on/off-line ability to work and gather data from either the smelter’s PI system® or database, and simulate the operation with or without scheduled events and controls.The main model development aspects, which include thermodynamics, metallurgical and kinetic considerations, slag-type and on-line mass and heat balances of the process, as well as the successful validation of the model, are presented and discussed in the present paper."

Jan 1, 2009

By Chi-Ming Chang

Alloy powders are commonly used in the purification of zinc sulfate solutions for use in standard electrowinning practice. The primary goal of this research was to study the use of zinc-lead alloys for similar reactions in the galvanic stripping of impurities from organic solutions. The effects of various parameters on the electrochemical behavior of commercially produced zinc-lead alloy powders were determined. A qualitative evaluation and summary of the influence of the more pertinent parameters on iron removal from di-(2-ethylhexyl) phosphoric acid (D2EHPA) by galvanic stripping is given. Water concentration, oxygen content and reaction temperature were the principal factors affecting the reaction rate and process efficiency. Activation energies were also calculated and indicated that the reaction changes from chemical to diffusion control .with increasing temperature in the range of 35" to 45°C. The results showed that zinc-lead alloy gave faster reaction rates with less sensitivity to process variables than SHG zinc as a reducing agent for galvanic stripping. The role of lead could be as cathodic sites for the reaction which enhances the zinc dissolution or anodic half reaction. The morphology of the zinc-lead alloy surfaces, before and after the reactions, supports this assumption.

Jan 1, 1998

By Alicia Esther Ares, Alex Iván Kociubczyk, Verónica Liliana Scheiber, Roberto Rozicki

In the present research the horizontal solidification of Sn-Zn eutectic alloys (Sn-8.9wt.%Zn) is performed, with two opposite senses of heat extraction. From the process of solidification, the thermal parameters (local solidification time, cooling rates and interphases velocities) and grain sizes from macrostructures obtained were determined. The presence of defects in the solidified samples was analyzed, observing that they occur largely in the collision zones of solidification fronts advancing in opposite directions in the samples.

Jan 1, 2016

By James T. Staley

Quenching and aging are critical processing steps used to produce precipitation hardenable aluminum alloy products. This work describes personal computer programs that employ models to predict certain properties after quenching and aging and graphically display them. One of the programs allows the user to predict the attainable strength and toughness of aluminum alloy products after an arbitrary quench. Another program simulates the changes in strength and electrical conductivity occurring during second-step aging alloy 7050-T7X products as a function of thickness, furnace temperature set point, and furnace characteristics.

Jan 1, 1993

By Dengfu Chen, Yi Yang, Chunmei Chen, Mujun Long, Shikai Gong, Junhao Sheng, Tao Liu

The relationship between thermo-physical properties of petroleum coke and temperature is of importance for determining of the operating parameters during the calcining graphitization process. In this paper, the variations of thermo-physical properties of petroleum coke versus temperature were investigated, such as the DSC-Tg curve, the specific heat capacity, the thermal diffusion coefficient, the thermal conductivity, and so on. The thermal analysis curve of petroleum coke showed synchronous thermal hysteresis at higher heating rates, indicating that a larger heating rate will cause delay of thermal effects. The thermal diffusivity of petroleum coke decreased during the calcining process. With increasing temperature, coefficient of heat conductivity and specific volume heat of the petroleum coke increased with a decreasing variation rate. The research provides a database for the calcining graphitization process of petroleum coke.

Jan 1, 2015

By Timothy W. Skszek, Adrian S. Sabau, Hebi Yin, Gerard M. Ludtka, Xiaoping Niu

"A constitutive model has been developed to predict the yield strength aging curves for aluminum casting alloys during non-isothermal age-hardening processes. The model provides the specific relationship between the process variables and yield strength. Several aging heat treatment scenarios have been investigated using the proposed model, including two-step aging recipes. Two-step aging heat treatments involve a low temperature regime to promote nucleation of secondary phases and a second step at higher temperature for the growth of the secondary phases. The predicted results show that a yield strength of approximately 300MPa might be obtained in a shorter aging time, of approximately 30 minutes. As a result, better mechanical properties can be obtained by optimizing the time-temperature schedules for the precipitation hardening process of heat treatable aluminum alloys.IntroductionA356 is one of the commercially heat treatable aluminum casting alloys, and T6 is one of the heat-treated conditions to improve mechanical properties. The first stage of a T6 temper is solution treatment at an elevated temperature, generally in the range of 480 - 540°C. After solution treatment, the cast part is typically quenched in water/air to retain the solute-rich homogeneous matrix chemistry at room temperature. Subsequent ageing treatment stages capitalize on this super-saturated solid solution to generate controlled dispersions of very small strengthening precipitates within the matrix of Al grains [l]."

Jan 1, 2013

By K. R. Robilliard

An outline is given of the problems facing tlile lead and zinc industry from the viewpoint of the range of residues currently produced from electrolytic zinc, blast furnace and other processes. Smelting approaches available using top submerged lancing technology are discussed and analysed. Pilot plant results for a range of lead and zinc-bearing materials are presented.

Jan 1, 1992

By J. M. Rapkoch

In late October 1996, an acid plant at a major U.S. copper smelter was faced with unexpected and rapidly increasing pressure drop across the gas cooling tower in the acid plant, indicating a build-up on the packing. This threatened to halt operations if not resolved. Earlier that month, a smaller vessel in the acid plant was found to be completely plugged with lead sulfate. It was feared that a similar fate awaited the gas cooling tower unless the scale build-up was stopped. Although lead sulfate is present in most copper smelter acid plants, this accumulation was unusually severe. An investigation was launched to find the source of the lead, determine how lead is transported to the gas cooling tower, recommend operating practices to prevent such severe scaling, and seek ways to recycle the lead value in the scale covered polypropylene packing. Late in the investigation it was learned that the lead originated from an improperly executed recycling program.

Jan 1, 2000

By Hebi Yin

A two-dimensional finite element solidification model was developed to simulate the transport phenomena occurring during laser deposition of AISI 410 stainless steel during the Laser Engineered Net Shaping (LENS®) process. The molten pool geometry and the distribution of temperature, solute concentration and velocity were calculated during deposition of a thin wall plate. An analysis of the simulations results revealed the importance of heat transfer by both conduction and convection as well as the roles of the driving forces for convection in the molten pool. The heat transfer and the flow pattern in the molten pool are considerably dependent on the travel speed of the laser beam. For the alloy and process parameters in the simulations, no significant macrosegregation was observed. The temperature-dependent properties and thermodynamic variables involved in solidification modeling were calculated using Thermo-Calc software. The results of this work contribute to the current understanding of transport phenomena in the molten pool of laser deposition processes.

Jan 1, 2008

By Lei Wang, Xiancong Zhao, Hongxu Li, Lifeng Zhang

Recovery of Fe from red mud has been studied using statistically designed experiments. The effects of three factors, namely: reduction temperature, reduction time and proportion of additive on recovery of Fe have been investigated. Experiments have been carried out using orthogonal central composite design and factorial design methods. A model has been obtained through variance analysis at 92.5% confidence level.

Jan 1, 2015

By Dale T. Peters

Conductivity, both electrical and thermal, are attributes accounting for about 70% of the applications of copper and its alloys. This paper presents results of on-going research into two new applications that depend on copper's excellent conductivity. The Copper Development Association (CDA), together with materials and motor company partners, is working toward a solution to the key problem preventing pressure die casting copper for the conductor bar/end ring structure of the induction motor rotor, i.e., lack of a durable high-temperature mold material. Work is showing that a combination of high- temperature materials and elevated temperature processing gives much improved mold life compared to die steels. Substitution of copper for aluminum in the rotor can result in a 20% decrease in electrical losses in motors consuming 35% of electrical power generated in the U.S. The second development uses the excellent thermal conductivity of several high-strength high-copper alloys to simultaneously improve productivity and part quality in the injection molding of plastic parts.

Jan 1, 1999

By N. G. Azeredo

This work dealt with the evaluation of engineering structural clay brick samples that were sintered at estimated temperatures of 700 and 800°C. They were collected in a red-brick plant in Campos dos Goytacazes, RJ, Brazil. From a lot, a sample already sintered in its kiln at 700°C were collected and also a sample from the same lot only dried by the air, which were then sintered at 800°C controlled temperature. The samples were subjected to Brazilian Standard tests (ABNT NBR 15270:2005) to determine their geometric, physical and mechanical properties. In order to be classified as structural clay brick it is required minimum 3.0 MPa for the characteristic compressive strength (fbk) to be suitable for up to five floors structural building applications. We also used the Weibull Probability Plot and Weibull Maximum Likelihood Estimation to evaluate distribution parameters in order to compare the results of compressive strength obtained in the tests.

Jan 1, 2015

By Teruo Tanabe

The hydrogen-absorbing materials are expected to have the following properties at moderate conditions, (a) a large capacity of hydrogen absorption, (b) the absorption rate of hydrogen is large and (c) hydrogen-absorbed materials can easily desorb hydrogen. Thus the three concepts of capacity, rate and reversibility seem to be indispensable to clarify the mechanism of hydrogen absorption by the materials. In this work, the amount of absorbed hydrogen, the absorption rate and the reversibility of hydrogen absorption- desorption reaction were measured for binary R-M systems (R = Y, La, Ce; M = Co, Ni). These experimental results were discussed by the following three physical properties that were calculated by the extended Hückel method, i.e. the density of states unoccupied by electrons, the cohesive energy and the energy fluctuation. The major results are as follows: (a) the amount of absorbed hydrogen increases with the density of states in the energy range between -9 and -4 eV, (b) the R-M compounds of which energy fluctuations are large show a large value of rate of hydrogen absorption, and (c) when the cohesive energy is large, the compound has a tendency not to easily desorb hydrogen, i.e. its reversibility is poor.

Jan 1, 2006

By Ian Masters

Rotary furnaces are widely used throughout the metals industry. These furnaces vary in size and geometry, but are fundamentally the same from a thermodynamic viewpoint. A generic method is proposed that can be used to model all furnaces of this type, provided that the correct material and process parameters are known. Various approaches have been attempted in the past based on a continuum (FEA or CFD) approach. However, the complex fluidlsolid interactions present in a rotary vessel are not easily solved using these methods, which work best where the material boundaries are well defined. In this paper a lumped parameter model is proposed. Variations within a section of the model are ignored, but to ensure thermodynamic correctness, the heat transfer between sections is carefully considered. For example, it is reasonable to assume that the whole of the melt pool is at the same temperature, due to rotary mixing. This may then be modeled with a single set of parameters, and the detail is contained in obtaining the correct heat transfer mechanisms from the rest of the furnace.

Jan 1, 2002

By Gerardo R. F. Alvear, Alistair S. Burrows, Stanko Nikolic, James S. Edwards

"The copper ISASMELT™ process has evolved over more than a quarter of a century and can now be considered mainstream, with single furnaces producing more than 340,000 tpa of copper in matte. The next evolutionary step for the ISASMELT™ technology is to directly challenge the dominance of the Peirce-Smith converter by the implementation of a continuous copper converting process on a commercial scale. The present work describes the status of the continuous converting process – ISACONVERT™.Continuous converting has been performed successfully in pilot scale ISACONVERT™ plants, where operating results have verified the predictions of fundamental research and reinforced the underlying confidence in the design parameters. From a matte feed rate of 250 kg/hr, a calcium ferrite slag and a low-sulfur blister have been produced. Design is now complete for the first commercial application of the ISACONVERT™ process. The present paper describes the status of ISACONVERT™ by summarising results of recent pilot plant tests and describing the first commercial plant design."

Jan 1, 2009

By Joseph C. Milbourne

Tetra Technologies CCIX? (continuous countercurrent ion exchange) system has been involved in a wide range of uranium concentration, separation and purification applications over the past 40 years. Uranium ion exchange applications have ranged from the treatment of copper heap leach solution containing 5 parts per million of uranium to the treatment of high strength sulfuric acid solutions containing several thousand parts per million of uranium. The flexibility and the countercurrent mode of operation and other unique features of the CCIX? have resulted in successful uranium recovery from these solutions and many others.

Jan 1, 1995

By E. Anelli

Based on experimental continuous cooling transformation (CCT) diagrams, an artificial neural network has been trained to predict the amount of microsturctural constituents and hardness resulting from and controlled cooling at rates from 150 to 0.015 K/s. It can be applied to quenching and normalizing processes of low-alloy steels with 0.05-0.30 C% and 0.4-2.0% Mn -with possible microalloying additions. Examples of the good predictive capabilities about 15 Vickers standard deviation for hardness and a few percent for volume fraction of phases) are reported' Keywords: Austenite decomposition, low. And medium-carbon steels, artificial neural networks

Jan 1, 2003