Search Documents

By Guangliang Wu, Dong-chang Huang, Xin-bin Liu

High temperature mechanical properties of 50Cr5MoV roll steel was investigated by Gleeble 1500 thermal simulator testing machine The morphology, composition and microstructure of fracture surface were observed and analyzed by OM, SEM and EDS The results are indicative of that, there are two brittle temperature zones of 50Cr5MoV roll steel at the temperature of 600°C~950°C and 1300°C~1450°C, respectively. The section shrinkage rate is less than 60% The fracture mode changes from mixed ones dominated by intergranular to toughness transgranular one with the increase of temperature at the range of 650°C~1300°C. The fracture is along the solid--liquid phase at the range of 1300°C~ melting point It is crucial to formulate the 50Cr5MoV casting technology, to prevent the cracks and improve the quality of 50Cr5MoV roll steel.

Jan 1, 2016

By Zhang Yongzhu

Sulfoxides are one kind of extractants for precious metals. The structure, the coordination reaction, the extraction behaviour and the precious metals complexes of sulfoxides are summarized. The differences between sulfides, sulfoxides and sulphones are also discussed.

Jan 1, 1992

By P. A. Treasure

The EMEW® cell has been developed to overcome a number of inherent limitations in conventional electrowinning technology, particularly the high cost and restricted process windows characteristic of conventional hardware. The technology has been widely demonstrated to achieve high performance for various metals under chemical conditions well outside the limits required for efficient operation of conventional cells. This process flexibility offers significant opportunities for cost savings. in recovery of zinc from primary and secondary sources. The EMEW® technology is now available on a fully engineered basis, as a versatile commercial alternative to conventional electrowinning hardware. Application of the EMEW® cell for recovery of secondary zinc material offers significant advantages to the recycling industry. For example, a selective caustic leach can be used where there are high levels of iron or other contaminants in the target material. The reagent requirement is minimal as most of the caustic is regenerated in the bell and zinc dust that may be required for electrolyte purification is produced in the cell. A high purity zinc powder or cathode is produced in the cell. In the case of acidic zinc electrolytes, the cell is capable of operating over a much wider range of operating conditions than a conventional cell.

Jan 1, 2000

By Wei Gao, Qing-cai Liu, Cun-fang Lu, Huimin Zheng, Jian Yang, Chun-ling Yao

"Mercury in flue gas of coal-fired plants was concerned as another serious pollution when sulfur dioxide pollution was controlled now. The adsorbent made from fly ash by thermal precipitation sulfur to remove mercury in fuel gas from coal combustion plant, SEM, BET, TGA and other measurement methods were used to characterize the effect on surface morphology, sulfur distribution and specific surface. High temperature deposition furnace was applied to increase sulfur content in fly ash based adsorbents produced in lab. The study found that sulfur attached to the adsorbent surface, mesopore and microporous structure, increasing its sulfur content of adsorbent. Sulfur was filled in interspace as small molecule S2, S5, increased their surface area and enhanced their adsorption capacity. The specific surface area increased by thermal precipitation sulfur, and specific surface area which increased with increasing temperature.1. IntroductionThe mercury emission caused by human activity has accounted for 10%-30% of total mercury emission all over the world[11, and the emission from coal-fired power plant have a huge proportion of these emission caused by human activity. Active carbon microstructure and surface morphology play an important role in its adsorption capability, which offers the potential for controlling environmental pollutant, such as sewage, fuel gas, atmosphere and et al [2,31, because it is a material with high specific surface area that long been considered as an excellent adsorbent. At present, include activated carbon, fly ash, calcium-based sorbents and other novel adsorbents. The adsorption capacity and production cost were very important in the process of mercury removal by adsorbents, so the mercury removal has focus on developing adsorbents of highly-efficient. In particular, the waste of metallurgical from coal combustion and the others have a significant advantage about the cost, and they have the highly-efficient in mercury removal after modified to enhance their adsorption capacity, such as fly ash of coal-fired. Apart from specific surface area, element content, pore structure, and surface morphology of activated carbon have great effect on its adsorption ability. Compared to adsorbents without modification, active carbon impregnated with other elements, such as chlorine, sulfur, bromine and et al. had more excellent characteristics to remove specific pollutants."

Jan 1, 2011

By Denise Cristina de O. Nascimento

Natural lignocellulosic fibers are increasingly being used as polymeric matrix composite reinforcement owing to economical and environmental advantages as renewable and biodegradable materials. Among these, the piassava fiber extracted from a palm tree native of South America stands as one of the most rigid with a potential to be used as composite reinforcement. Therefore, the present work investigates the notch toughness behavior, by Izod impact tests, of epoxy composites reinforced with up to 40 % in volume of continuous and aligned piassava fibers. It was found that the incorporation of piassava fibers results in significant increase in the impact energy of the composite. Scanning electron microscopy analysis showed that the nature of the piassava fiber interface with the epoxy matrix is the major responsible for the superior toughness of the composite.

Jan 1, 2009

By Isabela Leao Amaral da Silva, Felipe Perisse Duarte Lopes, Alice Barreto Bevitori, Sergio Neves Monteiro, Ruben Sanchez Rodriguez

"The fibers extracted from the stem of the ramie plant are among the strongest natural lignocellulosic fibers with a potential to be used as reinforcement of polymer matrix composites. Characterization of the ramie fiber has recently been conducted for its physical and mechanical properties. However, the effect of increasing temperature on the ramie fiber behavior has not yet been fully investigated. Therefore, the objective of this work was to perform a thermal analysis on ramie fibers with different diameters within the naturally found range of practical interest. The analysis was conducted by thermo-gravimetric, TGA and DTG, as well as differential scanning calorimetric, DSC, techniques. It was found that the ramie fibers present thermal stability up to 200°C and then suffer a sharp deterioration between 300 and 500°C, resulting in characteristic peaks.IntroductionSince the middle of last century, polymer composites have substituted many conventional monolithic materials in applications ranging from aerospace to sport [l]. The main advantages of these composites are the low density and flexible properties specially using fiber as reinforcement to suit the mechanical performance requirements [2]. These are usually high strength and stiffness requirements that could be reached with synthetic fibers such as glass, carbon and aramid fibers. In recent years, however, the use of synthetic fibers is being questioned in terms of problems caused to the environment. In fact, as non degradable material, synthetic fibers are associated with long term pollution when discarded. Moreover, the expended energy for fabrication and processing can be related to relatively large amounts of C02 emissions and represents a contribution to global warming [3]. Glass fiber, in addition, is toxic and cannot be incinerated as a waste in thermal power plants [ 4]. Possible substitutes for glass fiber are the natural fibers. Many natural fibers are today being considered as viable alternatives to replace glass fiber as reinforcement of polymer composites. In particular, some natural lignocellulosic fiber extracted from plants present a real potential for this replacement [2-8]. Their comparative advantages are lower density and reduced cost as well as renewability, biodegradability, recyclability and neutrality with respect to C02 emission [3]."

Jan 1, 2011

By Thomas Niehoff, Yin Qing, Wei Zhongling, Liu Yongguo, Zhang Deliang, Tang Le

The gold ore of Shandong Gold Mining (Xinhui) was a refractory ore, which contained multi metallic sulfides (ZnS and PbS etc.) and carbonaceous. The gold ore concentrate came into leaching process and thickener and zinc replacement to recover gold. In order to improve gold recovery, the GOLDOX™ hydrometallurgy process was studied in Shandong Gold (Xinhui) by bench scale and 6 month plant scale test supported by Linde Gas. It was shown that the process promoted the leaching kinetics and improved gold recovery. The residue grade reduced 0.22 g/t in average after oxygen was applied. This indicates an operating profit increase 850,000 yuan/a in the plant. It was setting a good example for similar gold mine plant and would promote the oxygen application in Chinese gold mining industry.

Jan 1, 2015

By S. A. Davis

In July of 1996, the Kroll process began production again at TIMET's Henderson, NV, manufacturing facility. This, after being shut down for several years due to low market demand for titanium. Faced with limited pond capacity and increasing costs for water and wastewater disposal and storage; process changes were made to recycle water used to wash Kroll titanium sponge back into the sponge leaching process. This idea was revisited from 1992-93, when three consecutive attempts to recycle water for this application were unsuccessful due to early pump failure. Since it was uncertain why previous attempts failed, a complete understanding of the existing system was first sought. This included reviewing piping and flow diagrams; taking field measurements for all the piping, valves, and fittings; analyzing the wastewater composition; and modeling the fluid dynamics and control of the system. The fluid dynamics of the system were modeled by breaking the piping network up into nodes and applying the Bernoulli equation to each segment. The fluid flowrate control valves were modeled for this purpose also and the models were used to help specify the required processing equipment and control ranges and tolerances. Once the project was completed, an operating procedure was prepared for operation, startup, and shutdown of the washer water recycle system.

Jan 1, 1999

By Guanghui Li

Nickel pig iron (NPI), used as a substitute for electrolytic nickel, is able to reduce the production cost of stainless steel greatly. Aiming for preparing NPI from nickeliferous laterite ore, a pilot-plant scale test of coal-based rotary kiln direct reduction of laterite ore was performed and reported in this study. In this process, the ground laterite sample (18.85% TFe and 1.52% Ni) mixed with additives, pulverized coal and binder was briquetted into briquettes with the size of 40mm×40mm×31mm, laterite ore briquettes and reducing coal were charged into a rotary kiln with the diameter of 1.6 m and the length of 16 m, for a retention period of 6~7 hours, in which reduction section temperature was ranging from 950~1050 oC. The reduced briquettes were water quenched, ball mill ground and beneficated via low intensity magnetic separation. A magnetic concentrate, Ferronickel powder, with 86.9% TFe and 8.0% Ni was obtained, and the corresponding magnetic recovery of iron and nickel are 75% and 96.3%, respectively.

Jan 1, 2014

By Jinliang Zhang, Jian Pan, Deqing Zhu

"Limestone and burnt magnesite were added to vary MgO content and basicity (CaO/SiO2 ratio) of pellets for investigating their influences on the properties of specularite pellets. At fixed MgO content, the addition of limestone does not affect on the properties of green balls significantly. The addition of burnt magnesite has obvious influence on the quality of green balls, especially on the thermal shock temperature. Without burnt magnesite, the thermal shock temperatures are about 400°C, and, the thermal shock temperature increases to 600~630°C by adding burnt magnesite. For preheated pellets, when the burnt magnesite is added, the compressive strength will be decreased. For roasted pellets without burnt magnesite, the calcium additives can form binding phase of calcium-ferrite, and suitable liquid phase will improve recrystallization of hematite, but excessive liquid will destroy the structure of pellets, so the compressive strength of pellet increases firstly and then decreases. When adding burnt magnesite, the compressive strength will increase as the basicity increases. When the basicity is more than 0.2, the compressive strength of the pellets various MgO content and basicity is above 2500N/pellet and then MgO-bearing fluxes can be added to prepare pellets with good high temperature properties.IntroductionWith the rapid development of the steel industry in China, oxidized pellets, possessing good mechanical and metallurgical properties, are becoming indispensable burdens for blast furnace ironmaking [1-3]. However, this has resulted in the shortage of domestic iron concentrates, so many Chinese steel plants begin to use imported hematite concentrate to prepare pellets. Compared with magnetite pellets, the hematite pellets require high roasting temperature and narrow roasting temperature range (1300–1350°C) and possess low compressive strength [4,5].1"

Jan 1, 2012

By Liya Bochkareva, David Hui, Sergey Eremeev, Maksim Kireitseu, Igor Nedavniy

The principal goal of the present paper is to demonstrate an application of modern software engineering tools for modeling virtual reality and molecular dynamics of novel nanocomposites. The main technical components of presented system are I) software and nanoengineering tools for modeling of virtual reality, molecular dynamic and 30 video images of novel diamcindscontaining nanocomposites and 2) Problem tracking system to be used during modeling of virtual reality. A computational scheme and software, which utilizes neural networks and/or Microsoft. Net technique was developed to predict properties of nano-structured materials and optimization and control of nano-devices. Developed software and IT nanoengineering tools can be used by both industrial and private single users. For commercial companies proposed technology may provide better cost-effective alternative to the existing solutions for nanoengineering and modeling their virtual realit. For private users (students, professors, and engineers) proposed technology and IT tools can provide simple and cost-effective solution for nanoengineering while studying, exploring virtual reality and modeling novel nanostructures and its properties leading to an innovation or a discovery. Because of using novel software and methodologies, users can easily operate proposed technologies by available computers and operating systems (Pentium III or IV). In addition, users can upgrade it by their own self-written models, if necessary. The proposed technologies could replace or be used along with technologies for modeling such as 30 max studio and others.

Jan 1, 2004

By Laurent Cohen

Since the 1970s, Solvent Extraction (SX) in hydrometallurgical processes has been a key enabling technology in the production of high-purity metals. Examples include copper, rare earth oxides, uranium, cobalt and nickel. Notwithstanding incremental improvements in extractant formulations, few breakthroughs can be recounted in this industry outside of the initial amine-, oxime- or phosphine-based reagent chemistries. However, the advent of lithium-ion batteries and their stringent requirements for critical materials (lithium, cobalt and nickel) offer new challenges and opportunities for SX. Solvay recently introduced a new extractant for lithium, CYANEX® 936, and developed unique modeling software capabilities in cobalt/nickel separation using CYANEX® 272, zinc SX using DEHPA® and rare earth separations using CYANEX® 572. This paper discusses trends in SX and provides insight on processing of critical materials essential to energy sources. It also summarizes the technical and economic benefits based on extractant selection and advances in modeling.

By Jun Chang, Jin-hui Peng, Jing Chen, Li-bo Zhang

The leaching of indium from refractory zinc oxide flue dust(ZOFD) is attempted to utilize microwave sulfating roasting process, followed by water leaching. The ZOFD and roasted product were characterized by XRD and SEM/EDS analysis. The effects of various roasting parameters, such as roasting temperature/duration, the proportion of sulfuric acid, as well as the leaching parameters such as the leaching duration and liquid/solid ratio, were assessed. The results indicate that nearly 97% of indium could be leached under the following conditions: mass ratio of concentrated sulfuric acid to ZOFD to be 0.5, roasting temperature of 150 ℃ and duration of 1.5 hours; while the optimal leaching conditions hold at temperature of 25 ℃ for 1 hour, with 4:1 of liquid/solid ratio. The indium leaching rate by the microwave roasting increased by 8% as compared with the conventional roasting process under identical conditions.

Jan 1, 2015

By Mim Li, Huimin Lu, Lisha Yang

"CuInS2 thin films solar cells have drawn much attention for their low-cost, stability and high conversion efficiency. The electrodeposition of Cu-In precursor films, as the first step in making CuinS2 solar cells electrochemically in the air-and water-stable ionic liquid based on choline chloride/urea eutectic mixture has been investigated at constant potential. Compared with aqueous electrolytes, the large electrochemical window as well as the high thermal stability of this ionic liquid allow the direct electrodeposition of Cu-In precursor films. Then the precursor films were sulfuretted in a tube furnace at different sulfurization temperatures to optimize the films properties. The films obtained were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), energy dispersive spectroscopy (EDS).IntroductionCuInS2 is one of the most prospective absorber materials for low cost thin film solar cells, with a high conversion efficiency that exceeds 32% in terms of theory and nearly 13% in laboratory level [1-2]. In addition to its long-term stability, CuinS2 has a band gap energy Eg ranging from 1.3 to 1.55 eV and an optimal optical absorption coefficient reaching 105cm-1 [3-4]. CuinS2 thin films have been prepared by several methods such as spray pyrolysis [5-6], r.f.sputtering [7], vacuum evaporation [8-9] and electrodeposition. Comparing with vacuum methods, electrodeposition has lots of advantages such as less energy consumption, preparation big area thin film, stable system and enabling cheaper films.The electrodeposition of most technologically important metals has been shown to be possible from a wide range of ionic liquids. These ionic liquids are currently applied in a wide variety area. It is reported that the cell efficiency of chalcopyrite absorber layer (CIS, CISeS, and CIGS) via an electrodeposition route in laboratory condition has reached 11.3% [10]. Copper and indium alloy film is regarded as important precursor for the production of compound semiconductors with sulfur. The electrodeposition of the alloy film from room temperature ionic liquid (RTIL) has not been widely investigated. Only few alloy films, such as ZnTe, CdTe, GaAs and AlSb have been electrodeposited."

Jan 1, 2011

By C. B. Piazzarollo

Ceramic materials exhibit dispersion results after being subjected to various levels of stress, from the point of view of mechanical strength. With the focus on sustainable development and to improve the strength of these material, was incorporated ornamental rock waste into clay in up to 10% in mass to conform some samples, that was fired to 750ºC, 850ºC and 950ºC and submitted to technological tests. This paper presents an analysis of the technological properties of the samples through the use of Weibull statistic to determine which the best firing temperature for these red ceramic materials. The Weibull Modulus indicates a greater homogeneity for samples with 10R at 950ºC.

Jan 1, 2015

By Jay R. Hitchings

A technique that enables excellent color photograph production from black and white negatives of electron microprobe x-ray images is described in this paper. The photographs are made by superimposing one, two or three negatives of black and white x-ray images individually through assigned primary color filters directly onto color print paper. When used to examine metallurgical or geological microstructures, the resulting color photograph provides detailed, qualitative information about spatial arrangements, elemental associations and relative concentrations of at least three elements. The technique is simple and straightforward, requiring only standard darkroom equipment. The use of color to display or present complicated microprobe data also allows a non-technical reader or audience to better understand the data.

Jan 1, 1981

By Tatsuzo Kitamura

The tank house of Tamano refinery, that started its operation in January, 1972, was constructed incorporating the application of Periodic Reverse Current (P.R.C.) from the outset of design works. In 1973, the production of electrolytic copper came up to 8,000 mtpm, a sharp increase ds compared with the designed capacity of 7,000 mtpm, and successful operation has been achieved up to the present. P.R.C. has been employed for the purpose of raising productivity level and reducing copper inventories. Since there were various problems in P.R.C. application to such a large sized cathode as 1 m x 1 m, special attentions were paid to the following items: -Development of a unique bus bar to make an electrolytic current to each electrode as uniform as possible. -Improvement of circulating method of electrolyte. -Application of high-performance equipment to realize a uniform spacing between anode and cathode. Owing to these creative technical developments mentioned above, technical level for operation up to 350 amp per sq m of cathode current density has been established. The quality of electrolytic copper, which was a matter of interest, has been proved to be as excellent as those of conventional electrolysis products through a long term supply to the field of SCR and Dip forming where high levels in quality are required.

Jan 1, 1976

By Minting Li, Hailong Yang, ChangWei, Cunxiong Li, Gang Fan, Xingbin Li, ZhiganDeng

The filtration problems on acid leaching sludge of high silicon zinc ore have been paid extensive attention in zinc hydrometallurgy. It was found that soluble silica can be effectively converted into silica precipitate with good settling, filtration and washing properties, and the filtration rate can be in excess of 800 L/m2 · h under certain leaching conditions. According to investigating on the filtration rate, viscosity and concentration of silica of leaching sludge or liquor, the filtering temperature can tremendously improve the filtration property of pulp. At the same time, the experimental data indicated that the viscosity of leaching liquor was the key factor influencing filtration property of leaching sludge.

Jan 1, 2016

By Yongqi Sun, Zuotai Zhang

Our study investigated the influence of P2O5 and B2O3 on the viscosity and crystallization behavior of Ti-bearing blast furnace (Ti-BF) slags for the purpose of Ti extraction. The investigation of the crystallization behaviors were carried out using a single hot thermocouple technique (SHTT) and the viscosity was obtained by rotating cylinder method. For the viscosity, the results showed that P2O5 substantially increased the slag viscosity. P2O5 is a network-forming oxide, which increased the degree of polymerization of slags and accordingly increased the slag viscosity. However, both of slag viscosity and apparent activation energy for viscous flow remarkably decreased with B2O3 addition. As a typical network forming oxide, B2O3 was introduced into the network and existed dominantly as 2-D structure, BO3 triangular, which caused a simpler structure and a decreasing slag viscosity. As for the crystallization behaviors of Ti-BF slags, both P2O5 and B2O3 enhanced the crystallization trend of rod-shape rutile and suppressed the crystallization trend of dendrite CaTiO3. Therefore the added P2O5 and B2O3 caused the primary phase change from CaTiO3 to rutile. Additionally, it was found that the rod-shape rutile showed a 1-D growth, whereas the dendrite CaTiO3 showed a 3-D growth style.

Jan 1, 2015

By Jiang Feng, Zhang Libo, Peng Jinhui, Guo Zhanyong, Ju Shaohua, Lei Ting

The clean utilization of the residue containing chloride, CuCl residue, produced from zinc hydrometallurgy is very important for the recycle of valuable metals. And drying is the main process in recycling. In this study, response surface methodology was used to optimize operating conditions of the drying of CuCl residue in a convection oven and desirability function used as the methodology for the optimization. Optimization factors were air temperature (80–100°C), material thickness (10–25mm) and process time (80–120min) while investigated responses was final moisture content. The optimum conditions were found to be the temperature of 95.48°C with the material thickness of 13.47mm for the process time of 89.48 min. Under optimum conditions, the predicted moisture content of CuCl residue was 4.11% while the experimental date was 4.13%. The experimental value after process optimization was found to agree satisfactory with the predicted value. After drying, XRD was used to analyze the main phases of CuCl residue. The CuCl residue is made up of CuCl,Cu2O, ZnS and other compounds.

Jan 1, 2015