Search Documents

By A. K. Mukherjee

The roles of pulsating mechanisms such as the amplitude and frequency of the jig cycle are well established in jigging. Also well established are the roles of the size ratio and the volume fraction of the feed. In iron ore beneficiation plants, these process parameters are optimized to achieve the highest efficiency. However, the role of one of the more important feed characteristics, the liberation characteristic of the feed, has not been studied in detail. Evaluation of the liberation characteristics is difficult because the required washability test is not viable for iron ore feed. In this paper, a new method is proposed in which the liberation characteristics are measured through a separation efficiency value. In the new evaluation method, jigging parameters such as amplitude and frequency of the jig cycle are optimized from the fundamental understanding of the process dynamics and feed characteristics such as size distribution. Then, feeds with different liberation characteristics are tested to evaluate the liberation characteristics of feed in jigging.

Jan 1, 2008

By R. A. Wood, R. I. Jaffee, H. R. Ogden, D. N. Williams

Strain-induced porosity has been found to occur in titanium and other materials at tensile strains greater than the uniform elongation of the material. Porosity in titanium increases with increasing strain and temperature, being most severe at 300° to 800°F. Strain-induced porosity is believed to be a normal part of the mechanism of deformation in ductile materials. DURING the past few years there have been numerous references to the occurrence of voids in laboratory test specimens of metals subjected to strain.l-7 These voids have been referred to as intercrystalline cracking, strain-induced porosity, intergranular cav-itation, voids, and porosity. They appear to occur at grain boundaries or interfaces, and are generally associated with large amounts of strain and have been found mostly in creep specimens and to a lesser extent in tensile specimens. Because the phenomenon does not occur unless the material has been strained,

Jan 1, 1960

By P. C. Schutte

Ergonomics is the scientific discipline concerned with the understanding of interactions among humans and other elements of a system, and the profession that applies theory, principles, data and methods to design in order to optimize human well-being and overall system performance. Despite the fact that the application of ergonomics principles can make a major contribution to the management of significant occupational safety and health risks, ergonomics is currently applied on a limited scale in the South African mining industry. The objective of this paper is to provide a perspective of ergonomics, the main aim being to create a point of departure for the development of strategic objectives to enhance existing health and safety initiatives through the application of sound ergonomics principles. Two of the major consequences of poor ergonomics, namely work-related musculoskeletal disorders and worker fatigue, and possible means of introducing ergonomics into the South African mining industry, are discussed.

Jan 1, 2005

Gas well tests were performed on 17 wells in the Roma area. The procedure used in the test programme incorporates an initial isochronal test followed by what is described as the "two flow drawdown" technique. The second flow of the two flow drawdown test was conducted for sufficient time to allow transient investigation of the surrounding reservoir. This combination of tests allows the evaluation of stabilized production capacity in addition to the determination ,of several important reservoir characteristics.It also provides a qualitative indication of reserves, by reflecting the presence or absence of reservoir boundaries within the drainage area affected during the test.

Jan 1, 1968

By I. E. Wahn, E. A. Boutin

"The Manibridge Mill is unique in its treatment of relatively high grade nickel-copper ore because in the mill design are included one 10' diam. x 10' Maxwell cell, and three 12' diam. x 12' tank cells. These large cells are used as rougher-scavenger cells. Three 8' diam. x 8' tank cells as well are used for cleaning and recleaning of the tank cell concentrate.Flexibility of flow is the main criterion in the tank cell circuit. Targets from these cells are a high grade nickel-copper product with a minimum of talcose gangue.The operation of the tank cells has been encouraging and they have performed well with both low and high grade heads, yielding a high grade concentrate product.Manibridge Tank CellsDescription:The tank cells at Manibridge consist of one 10' x 10' Maxwell cell, three 12' x 12' tank cells, and three 8' x 8' tank cells. The four large cells are currently being used as rougher scavenger cells. The three small cells are used as cleaner cells.Both sets of tank cells consist of Denver steel tank and Super Agitator Mechanisms with steel beam super-structures. The agitator mechanism has a totally enclosed ball bearing spindle housing with a cold rolled steel shaft, and a stanclard standpipe with adjustable collar.The air rings for the tanks were fabricated by Nelson Machinery. Both large and small cells have injection rings with equally spaced air holes in the bottom centre line of the ring.Air is supplied to the tank cells by a Dresser Clark low pressure air blower.The following is a table of pertinent data on the tank cells:"

Jan 1, 1974

De acuerdo a los últimos trabajos realizados sobre la exploración en la mina Cercapuquio, se realizó un muestreo de la veta 53 donde se observó que en la caliza, más allá del ala norte, como en el lugar llamado Chaupirange, existe grandes depósitos de carbonado estático con siderita y limonita, en bolsa de erosión de la caliza normal. Asimismo, se describe otros métodos utilizados para la exploración geofísicadel subsuelo como los electromagnéticos e inducción. En ese sentido, se trata de crear un campo (primario) a través de una corriente eléctrica alterna (primaría) en un circuito. A este campo, es concadenada una corriente (secundaria) que circula en el cuerpo conductor mismo ( en general desfasada respecto de la primaria), que genera a su vez, un campo secundario. Este último se compone con el campo primario para formar un campo total, que está relacionado con la posición y naturaleza del cuerpo conductor que funciona de circuito secundario.

Jan 1, 1956

Pressure Oxidation of Sulfide Gold-Bearing Concentrates with Double Refractoriness

Sep 13, 2010

By Z. J. Hladysz

A Deep Underground Science and Engineering Laboratory (DUSEL) is being planned at the site of the former Homestake Gold Mine in Lead, South Dakota, under the sponsorship of the National Science Foundation (NSF) in cooperation with the Department of Energy (DOE). This national facility will host a variety of multi-disciplinary science and engineering experiments including physics experiments that require shielding from cosmogenic radiation. Current plans include construction of large rooms (up to 55 m in width) at depths of 1.48 km (4850 ft) and 2.25 km (7400 ft) below the surface. Preparation of the preliminary design required the development of a geotechnical characterization program including: preliminary drilling and coring, core logging, drill hole mapping with a televiewer, drift mapping of the geology and rock structure, in-situ stress measurements, and laboratory testing of the mechanical properties of the rocks and discontinuities. Overall rock quality is very good to excellent. Site investigations were followed by geotechnical assessments for the construction of caverns and laboratory modules. The results are favorable and reaffirm selection of the Homestake site for establishment of a Deep Underground Engineering and Science Laboratory.

Jan 1, 2011

By Walter D. Holland

This is one of a series of instruction guides developed to help instructors present health and safety training courses to workers in the coal mining industry. This course is intended for training those, usually the safety officers, who perform surveys fur inhalation contaminants in above ground work areas. The handbook entitled ?Handbook for Surveys of Inhalation Contaminants in Above Ground Coal Mining and Processing Work Areas? (NTIS #PB-243-35";) is used as a manual for the course and as a prime reference when performing the actual surveys or interpreting the sampling results. There are six experiments for the students to perform during the course to familiarize them with the sampling devices routinely used during the surveys.

Jan 1, 1976

By Horst Peter Wölfel

The goal of biodynamic models is to simulate the vibration behaviour of the human body. In combination with experimental studies biodynamical models can be a powerful tool for the analysis of the effects of vibration exposure on health [1] and comfort. This paper gives an overview of the state of the art of biodynamic whole-body vibration models of humans, addressing both numerical models and hardware dummies. Method Two approaches are distinguished, the phenomenological and the anatomical, as illustrated in Figure 1. [ ] Phenomenological models aim to reproduce the vibration behaviour of humans with respect to particular physical quantities, chiefly the driving-point impedance at the interface to the seat, and partly with respect to other transfer functions. Discrete systems of masses, springs, and dampers with several degrees of freedom whose topology and parameters are determined by structure- and parameter identification methods are used in the sense that the functions derived from measurements are reproduced as well as possible. This paper provides an evaluation of this methodology and defines its range of application as well as its limits.

Jan 6, 2006

Rhyolitic rocks are volumetrically significant in the eastern part of the Coromandel gold province, yet deposits hosted by rhyolite (Kapowai, Broken Hills, Neavesville, Wharekirauponga and Waihi Beach) are generally low grade and subeconomic, especially compared with andesite-hosted deposits. In contrast, rhyolitic volcanic centres in Nevada host a number of economically significant epithermal gold deposits such as Round Mountain, Sleeper and Bullfrog. The Nevada deposits are associated with 27-20 Ma continental arc volcanics dominated by ignimbrites (eg Round Mountain), or younger 17-9 Ma bimodal rhyolite-basalt volcanism related to extensional basin-and-range tectonics (eg Sleeper). The Round Mountain deposit is localised on a caldera boundary fault and the mineralisation was deposited soon after eruption of the host rhyodacitic ignimbrite. In other Nevada deposits, hydrothermal systems are linked to the closing stages of flow-dome complexes and mineralisation is localised along normal faults associated with extensional basin-and-range tectonism. The style and composition of the mineralisation is similar in both the Coromandel and Nevada deposits and consists of sheeted and stockwork quartz veins, containing electrum as the main ore mineral and only minor sulphides (mainly pyrite) Likewise, the vein minerals were deposited from low salinity hydrothermal fluids in the temperature range of 200-270¦C. Both the Neavesville and Round Mountain deposits are geochemically anomalous in molybdenum. The deep oxidation of the Nevada gold deposits, dry climate and low level of competing land uses combine to make it economic to mine and process very low grade ore (0.2 - 2.0 g/t Au) by heap-leaching with cyanide solutions in most areas of Nevada. Although extensive low grade gold mineralisation is known at deposits such as Wharekirauponga and Neavesville, it is sub-economic because of shallow oxidation and land use conditions that are unfavourable for open pit mining and heap leaching.

Jan 1, 1996

By Jeffrey M. Listak

This report describes a study, conducted jointly by BethEnergy Mines Inc. and the Bureau of Mines, to assess the effects of longwall front abutment loading on various supplemental support materials utilized in a predriven recovery room. The purpose of the predriven recovery room is to reduce longwall equipment transfer time by eliminating the premove preparation associated with conventional recovery methods. In addition, the room provides a large area in which face salvage equipment can maneuver. Results of four recovery-room study areas show the progression and influence of the front abutment on the longwall panel and supports and their subsequent behavior. The best performance (i. e. the support that most facilitated recovery) of support material was achieved through the use of a concrete mixture which had a sand content of 35 percent by volume. The longwall transfer time was reduced by 30 percent which translates to a production advantage of 37,000 raw tons of coal per panel.

Jan 1, 1989

By C. H. Dionne, J. A. Holmes, B. J. Huls

"Falconbridge Limited is presently developing flowsheet alternatives for implementation at the Strathcona Mill. The main thrust for change arises from the need to reject more pyrrhotite from the concentrate. To maintain appropriate levels of sulphur in the smelter concentrate, however, enhanced removal of non-sulphide gangue minerals must be realized. This could best be done in the Non-magnetics flotation circuit.Laboratory investigations were followed by an on-stream pilot test at Strathcona. The application of a column cleaner on the Non-magnetics concentrate resulted in significantly lower levels of fine gangue at equivalent sulphides recovery.This paper discusses the laboratory and pilot testing and results, with a focus on piloting. Also included is a discussion of the Strathcona Mill Flowsheet and the role of the Nonmagnetics flotation circuit.INTRODUCTIONFalconbridge Ltd. is currently developing means to reduce atmospheric sulphur dioxide emissions. One alternative is a reduction in the amount of pyrrhotite in Strathcona Mill concentrate, which reports to the smelter. Pyrrhotite in the Falconbridge ores contains an average of 39 percent sulphur and 0.64 percent nickel. By comparison, pentlandite contains an average of 33 percent sulphur and 34 percent nickel.A consequence of the rejection of pyrrhotite is a decrease in the sulphur assay in the remaining concentrate. This decrease causes downstream difficulties in the roasting process. Therefore, the content of non-sulphide gangue in the mill concentrate must also be reduced in order to maintain sulphur grades adequate for roasting. The resulting concentrate will have lower sulphur dioxide emissions while maintaining nickel production."

Jan 1, 1991

By Albert Zima

ACCORDING to recently published statistics, it is predicted that as much oil must be produced during the next 16 years as has been produced during the past 75, in order to satisfy the high rate of consumption of petroleum products. During 1934, over 17,000 oil wells were completed in the United States, and it is expected that over 20,000 additional wells will be drilled during the current year. Were it not for the remarkable progress made during recent years in the improvement of drilling technique and in the development of equipment used in the production phase of the oil industry, it is doubtful whether sufficient oil could be produced to meet present requirements. A few years ago, wells seldom were deeper than 3500 to 4000 ft., owing to the limitations of the drilling methods and equipment employed. Today, however, through the application of scientific drilling methods and the adaptation of modern equipment and improved materials, many wells range from 6000 to 8000 ft. in depth, and a few recent completions exceed 10,000 feet.

Jan 1, 1935

By Donald Thompson, Jessie Bonner, Ileana Tibuleac

Predicting ground motion from complicated mining explosions is important for mines developing blasting programs in regions where vibrations must be kept below certain levels. Additionally, predicting ground motion from explosions in complex 3D media is important for source size estimation for nuclear treaty monitoring. Both problems have been addressed under the development of a new series of programs including: 1) Generalized Fourier Methods to generate synthetic seismograms (Green’s functions) in 3D media for a moment tensor source implementation and 2) MineSeis3D, a program that simulates seismograms for delay-fired mining explosions with a linear relationship between signals from small size individual shots. To test the programs, three-component seismic recordings of three production shots at an iron mine in northern Minnesota were compared to synthetic waveforms in 3D media. Comparison of the observed and synthetic waveforms shows promising results. The shape and arrival times of the normalized synthetic and observed waveforms are similar for most of the stations. The synthetic and observed waveform amplitude fit is best for the vertical components in the mean 3D model but not as promising for the transversal components. The observed effect of spall on the waveform spectra was weak in the case of fragmentation delay-fired mining explosions. Commercial applications of the code could provide data needed for designing explosions that do not exceed ground vibration requirements posed by the United States Department of Interior, Office of Surface Mining.

Jan 1, 2005

By W P. Player

The legislative operating environment, or the mineral regime, that a country has to offer is one of the key determinants that a company wanting to invest in an area takes into account in formulating its investment decision.   The New Zealand Government recognises this and the importance of getting the regime right in order to provide for continuing investment in mineral exploration and mining in New Zealand . In recent years, the Government has given considerable attention to developing legislation which provides for investment to take place; for those making the investments to have a stable, fair and open investment environment with government intervention only when considered absolutely necessary because other approaches are not working; and for the people of New Zealand to know that investment must meet acceptable health and safety standards and have acceptable impact on the environment. Also of key importance is having a clearly defined mining regime which includes rules on how to obtain a permit and rules in respect of ongoing permit compliance, rights to develop a mineral resource and permit conditions (in particular, the royalty regime). In New Zealand , these matters will all be addressed in what are referred to as 'minerals programmes'.   The Crown Minerals Act 1991, which is the legislation governing the allocation and management of permits for Crown owned minerals, requires that the Minister of Energy prepare minerals programmes. Minerals programmes establish the policies, procedures and provisions that the Minister shall follow in exercising his or her functions and powers under the Crown Minerals Act. Minerals programmes set out the principal reasons for and against adopting these policies, procedures and provisions and also restrictions on prospecting, exploration and mining for Crown owned minerals. Essentially minerals programmes define the mining regime for the minerals to which they apply, other than the taxation regime, environmental and health, safety provisions, land access matters and general matters concerning the investment climate.

Jan 1, 1995

The paper outlines the development of a solvent extraction process for the recovery of scandium, yttrium, thorium, and heavy lanthanides from waste sulphate liquor at the Port Pirie uranium treatment plant. A summary is given of known solvents for these elements, including the recently developed alkyl-phosphoric acid esters which are applicable to sulphate solutions.A kerosene solution of di- (2'-ethylhexyl) phosphoric acid (EHPA) has been suggested by some workers as a suitable solvent for fractionation of the lanthanides. Experimental work with this solvent showed that it could be used for initial recovery of the above elements from low concentrations in the complex sulphate liquor. In particular, scandium could be recovered as a high grade product by extraction with 0·lM EHPA, followed by a purification strip with 9N sulphuric acid, and final stripping of scandium with sodium hydroxide solution.To enable alkaline stripping to be used successfully, the kerosene solution of the reagent was modified by the addition of a small proportion of nonanol. Experimental work included laboratory scale batch tests and small pilot scale continuous tests.A proposed extension of the process for the separate recovery of individual heavy lanthanides, yttrium, and thorium is described.INTRODUCTIONAt the Port Pirie uranium treatment plant of the South Australian Government, large volumes of "barren liquor", free from 'uranium, are at present run to waste. This "barren liquor" results from sulphuric acid leaching of Radium,Hill uranium concentrate, followed by separation of solid residues and removal of uranium from the clear solution by ion exchange. The mineral davidite, from which the uranium is derived, contains other potentially valuable components, notably vanadium, chromium, thorium, yttrium, scandium, and the lanthanides. These constituents are...

Jan 1, 1961

By B. G. Tarasov

This paper proposes the further development of a recently identified shear rupture mechanism (fan mechanism) that elucidates a paradoxical feature of hard rocks ? the possibility of shear rupture propagation through a highly confined intact rock mass at shear stresses that can be significantly less than frictional strength. In the fan mechanism, failure is associated with consecutive creation of small slabs (known as ?domino blocks?) from the intact rock in the rupture tip, driven by a fan-shaped domino structure representing the rupture head. The fan head combines such unique features as extremely low shear resistance, self-sustaining stress intensification, and self-unbalancing conditions. Consequently, the failure process caused by the mechanism is inevitably spontaneous and violent. Physical and mathematical models explain unique and paradoxical features of the mechanism, which can be generated in primary ruptures and segmented faults. The fan mechanism provides a novel point of view for understanding the nature of spontaneous failure processes, including shear rupture rockbursts. The process explains, in particular, features of shear rupture rockbursts such as activation at great depths, generation of new shear ruptures in intact rock mass, nucleation of hypocentres at significant distances from the excavation, shear rupture development at low shear stresses, and abnormal rupture violence.

Jan 1, 2014

By B. M. Coombes

The McCracken and Stacey (1989) method of assessing geotechnical risk for largediameter raisebored shafts has been the basis for most Australian pre-construction raisebore investigations for the past 20 years. At the time of its publication, the McCracken and Stacey (M&S) Method did not include a database of raisebore diameter and rock mass conditions versus actual performance. It did, however, provide a chart that quantified geotechnical risk in terms of proposed shaft diameter and the raisebore rock quality index, QR. Two parameters, RQD/Jn and Jr/Ja were identified as being critical to raisebore stability, but the contribution of these to overall raisebore stability was not quantified. Peck and Lee (2008) published a database of raisebore performance from Australian case histories. Raisebore diameter and ground conditions, in terms of a Lower Bound QR value, were presented for 50 cases versus raisebore performance. This paper updates the database with further case histories and corrected SRF values. This paper further evaluates the reasons for the variable raisebore performance for similar RSR values. For all case histories, three parameters, RQD/Jn, Jr/Ja and Jw/SRF are investigated to assess their influence on raisebore performance.

May 1, 2011

By M Dickie

During the 1980s and early 1990s low cost gold treatment plants were at the forefront of the Australian engineering and mineral processing business. This opportunity was the result of a high gold price and innovative design by emerging engineering companies in an expanding market. The low cost approach to gold plant design and project execution resulted in smaller and shorter life projects becoming viable and the multiplicity and fast track approach of the projects resulted in sharp learning curves. From the mid 1990s to the early 2000s the relatively low commodity prices and resultant reduction in minerals opportunities also resulted in innovative design in both small and large plants, albeit on a reduced scale. The innovation was associated with alleviating capital cost pressures for large capacity low-grade (eg NewcrestÆs Cadia) or small-scale (eg JubileeÆs Cosmos) projects to either improve NPV or to enable the project to be won and profitable in the competitive lump sum environment. Between 2004 and 2008 the engineering market became less competitive from an engineerÆs perspective due to the high demand for engineering services in a high price commodity market. The need for innovation remained but was driven overtly by shortages in water, power and personnel and long equipment lead times. This paper discusses some of the factors that contribute to the capital cost of a project and the scope for improving the likelihood of financing and increasing the project net present value (NPV). Case studies with recent large copper concentrator projects will be used to demonstrate how a value driven approach to project and plant layout can result in significant improvement in NPV.

Jan 1, 2009